My patch, memcg-fix-gfp_mask-of-callers-of-charge.patch changed gfp_mask
of callers of charge to be GFP_HIGHUSER_MOVABLE for showing what will
happen at memory reclaim.
But in recent discussion, it's NACKed because it sounds ugly.
This patch is for reverting it and add some clean up to gfp_mask of
callers of charge. No behavior change but need review before generating
HUNK in deep queue.
This patch also adds explanation to meaning of gfp_mask passed to charge
functions in memcontrol.h.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements per cgroup limit for usage of memory+swap. However
there are SwapCache, double counting of swap-cache and swap-entry is
avoided.
Mem+Swap controller works as following.
- memory usage is limited by memory.limit_in_bytes.
- memory + swap usage is limited by memory.memsw_limit_in_bytes.
This has following benefits.
- A user can limit total resource usage of mem+swap.
Without this, because memory resource controller doesn't take care of
usage of swap, a process can exhaust all the swap (by memory leak.)
We can avoid this case.
And Swap is shared resource but it cannot be reclaimed (goes back to memory)
until it's used. This characteristic can be trouble when the memory
is divided into some parts by cpuset or memcg.
Assume group A and group B.
After some application executes, the system can be..
Group A -- very large free memory space but occupy 99% of swap.
Group B -- under memory shortage but cannot use swap...it's nearly full.
Ability to set appropriate swap limit for each group is required.
Maybe someone wonder "why not swap but mem+swap ?"
- The global LRU(kswapd) can swap out arbitrary pages. Swap-out means
to move account from memory to swap...there is no change in usage of
mem+swap.
In other words, when we want to limit the usage of swap without affecting
global LRU, mem+swap limit is better than just limiting swap.
Accounting target information is stored in swap_cgroup which is
per swap entry record.
Charge is done as following.
map
- charge page and memsw.
unmap
- uncharge page/memsw if not SwapCache.
swap-out (__delete_from_swap_cache)
- uncharge page
- record mem_cgroup information to swap_cgroup.
swap-in (do_swap_page)
- charged as page and memsw.
record in swap_cgroup is cleared.
memsw accounting is decremented.
swap-free (swap_free())
- if swap entry is freed, memsw is uncharged by PAGE_SIZE.
There are people work under never-swap environments and consider swap as
something bad. For such people, this mem+swap controller extension is just an
overhead. This overhead is avoided by config or boot option.
(see Kconfig. detail is not in this patch.)
TODO:
- maybe more optimization can be don in swap-in path. (but not very safe.)
But we just do simple accounting at this stage.
[nishimura@mxp.nes.nec.co.jp: make resize limit hold mutex]
[hugh@veritas.com: memswap controller core swapcache fixes]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For accounting swap, we need a record per swap entry, at least.
This patch adds following function.
- swap_cgroup_swapon() .... called from swapon
- swap_cgroup_swapoff() ... called at the end of swapoff.
- swap_cgroup_record() .... record information of swap entry.
- swap_cgroup_lookup() .... lookup information of swap entry.
This patch just implements "how to record information". No actual method
for limit the usage of swap. These routine uses flat table to record and
lookup. "wise" lookup system like radix-tree requires requires memory
allocation at new records but swap-out is usually called under memory
shortage (or memcg hits limit.) So, I used static allocation. (maybe
dynamic allocation is not very hard but it adds additional memory
allocation in memory shortage path.)
Note1: In this, we use pointer to record information and this means
8bytes per swap entry. I think we can reduce this when we
create "id of cgroup" in the range of 0-65535 or 0-255.
Reported-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Tested-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Reported-by: Hugh Dickins <hugh@veritas.com>
Reported-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Pavel Emelianov <xemul@openvz.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix misuse of gfp_kernel.
Now, most of callers of mem_cgroup_charge_xxx functions uses GFP_KERNEL.
I think that this is from the fact that page_cgroup *was* dynamically
allocated.
But now, we allocate all page_cgroup at boot. And
mem_cgroup_try_to_free_pages() reclaim memory from GFP_HIGHUSER_MOVABLE +
specified GFP_RECLAIM_MASK.
* This is because we just want to reduce memory usage.
"Where we should reclaim from ?" is not a problem in memcg.
This patch modifies gfp masks to be GFP_HIGUSER_MOVABLE if possible.
Note: This patch is not for fixing behavior but for showing sane information
in source code.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a small race in do_swap_page(). When the page swapped-in is
charged, the mapcount can be greater than 0. But, at the same time some
process (shares it ) call unmap and make mapcount 1->0 and the page is
uncharged.
CPUA CPUB
mapcount == 1.
(1) charge if mapcount==0 zap_pte_range()
(2) mapcount 1 => 0.
(3) uncharge(). (success)
(4) set page's rmap()
mapcount 0=>1
Then, this swap page's account is leaked.
For fixing this, I added a new interface.
- charge
account to res_counter by PAGE_SIZE and try to free pages if necessary.
- commit
register page_cgroup and add to LRU if necessary.
- cancel
uncharge PAGE_SIZE because of do_swap_page failure.
CPUA
(1) charge (always)
(2) set page's rmap (mapcount > 0)
(3) commit charge was necessary or not after set_pte().
This protocol uses PCG_USED bit on page_cgroup for avoiding over accounting.
Usual mem_cgroup_charge_common() does charge -> commit at a time.
And this patch also adds following function to clarify all charges.
- mem_cgroup_newpage_charge() ....replacement for mem_cgroup_charge()
called against newly allocated anon pages.
- mem_cgroup_charge_migrate_fixup()
called only from remove_migration_ptes().
we'll have to rewrite this later.(this patch just keeps old behavior)
This function will be removed by additional patch to make migration
clearer.
Good for clarifying "what we do"
Then, we have 4 following charge points.
- newpage
- swap-in
- add-to-cache.
- migration.
[akpm@linux-foundation.org: add missing inline directives to stubs]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page_queue_congested() was introduced in 2002, but it was never used
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Complete zap_pte_range()'s coverage of bad pagetable entries by calling
print_bad_pte() on a pte_file in a linear vma and on a bad swap entry.
That needs free_swap_and_cache() to tell it, which will also have shown
one of those "swap_free" errors (but with much less information).
Similar checks in fork's copy_one_pte()? No, that would be more noisy
than helpful: we'll see them when parent and child exec or exit.
Where do_nonlinear_fault() calls print_bad_pte(): omit !VM_CAN_NONLINEAR
case, that could only be a bug in sys_remap_file_pages(), not a bad pte.
VM_FAULT_OOM rather than VM_FAULT_SIGBUS? Well, okay, that is consistent
with what happens if do_swap_page() operates a bad swap entry; but don't
we have patches to be more careful about killing when VM_FAULT_OOM?
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the srandom32((u32)get_seconds()) from non-rotational swapon:
there's been a coincidental discussion of earlier randomization, assume
that goes ahead, let swapon be a client rather than stirring for itself.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Joern Engel <joern@logfs.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change pgoff_t nr_blocks in discard_swap() and discard_swap_cluster() to
sector_t: given the constraints on swap offsets (in particular, the 5 bits
of swap type accommodated in the same unsigned long), pgoff_t was actually
safe as is, but it certainly looked worrying when shifted left.
[akpm@linux-foundation.org: fix shift overflow]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Though attempting to find free clusters (Andrea), swap allocation has
always restarted its searches from the beginning of the swap area (sct),
to reduce seek times between swap pages, by not scattering them all over
the partition.
But on a solidstate swap device, seeks are cheap, and block remapping to
level the wear may be limited by zones: in that case it's better to cycle
around the whole partition.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Swap allocation has always started from the beginning of the swap area;
but if we're dealing with a solidstate swap device which can only remap
blocks within limited zones, that would sooner wear out the first zone.
Therefore sys_swapon() test whether blk_queue is non-rotational, and if so
randomize the cluster_next starting position for allocation.
If blk_queue is nonrot, note SWP_SOLIDSTATE for later use, and report it
with an "SS" at the right end of the kernel's "Adding ... swap" message
(so that if it's both nonrot and discardable, "SSD" will be shown there).
Perhaps something should be shown in /proc/swaps (swapon -s), but we have
to be more cautious before making any addition to that format.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When scan_swap_map() finds a free cluster of swap pages to allocate,
discard the old contents of the cluster if the device supports discard.
But don't bother when swap is so fragmented that we allocate single pages.
Be careful about racing allocations made while we're scanning for a
cluster; and hold up allocations made while we're discarding.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When adding swap, all the old data on swap can be forgotten: sys_swapon()
discard all but the header page of the swap partition (or every extent but
the header of the swap file), to give a solidstate swap device the
opportunity to optimize its wear-levelling.
If that succeeds, note SWP_DISCARDABLE for later use, and report it with a
"D" at the right end of the kernel's "Adding ... swap" message. Perhaps
something should be shown in /proc/swaps (swapon -s), but we have to be
more cautious before making any addition to that format.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before making functional changes, rearrange scan_swap_map() to simplify
subsequent diffs. Actually, there is one functional change in there:
leave cluster_nr negative while scanning for a new cluster - resetting it
early increased the likelihood that when we have difficulty finding a free
cluster, another task may come in and try doing exactly the same - just a
waste of cpu.
Before making functional changes, rearrange struct swap_info_struct
slightly: flags will be needed as an unsigned long (for wait_on_bit), next
is a good int to pair with prio, old_block_size is uninteresting so shift
it to the end.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel has not supported v0 SWAP-SPACE since 2.5.22: I think we can
now safely drop its "version 0 swap is no longer supported" message - just
say "Unable to find swap-space signature" as usual. This removes one
level of indentation from a stretch of sys_swapon().
I'd have liked to be specific, saying "Unable to find SWAPSPACE2
signature", but it's just too confusing that the version 1 signature shows
the number 2.
Irrelevant nearby cleanup: kmap(page) already gives page_address(page).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the SWP_ACTIVE mask: it just obscures the SWP_WRITEOK flag.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sys_swapon()'s swapfilesize (better renamed swapfilepages) is declared as
an int, but should be an unsigned long like the maxpages it's compared
against: on 64-bit (with 4kB pages) a swapfile of 2^44 bytes was rejected
with "Swap area shorter than signature indicates".
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rik suggests a simplified get_scan_ratio() for !CONFIG_SWAP. Yes, the gcc
optimizer gives us that, when nr_swap_pages is #defined as 0L. Move usual
declaration to swapfile.c: it never belonged in page_alloc.c.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's a possible race in try_to_unuse() which Nick Piggin led me to two
years ago. Where it does lock_page() after read_swap_cache_async(), what
if another task removed that page from swapcache just before we locked it?
It would sail though the (*swap_map > 1) tests doing nothing (because it
could not have been removed from swapcache before its swap references were
gone), until it reaches the delete_from_swap_cache(page) near the bottom.
Now imagine that this page has been allocated to swap on a different swap
area while we dropped page lock (perhaps at the top, perhaps in unuse_mm):
we could wrongly remove from swap cache before the page has been written
to swap, so a subsequent do_swap_page() would read in stale data from
swap.
I think this case could not happen before: remove_exclusive_swap_page()
refused while page count was raised. But now with reuse_swap_page() and
try_to_free_swap() removing from swap cache without minding page count, I
think it could happen - the previous patch argued that it was safe because
try_to_unuse() already ignored page count, but overlooked that it might be
breaking the assumptions in try_to_unuse() itself.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove_exclusive_swap_page(): its problem is in living up to its name.
It doesn't matter if someone else has a reference to the page (raised
page_count); it doesn't matter if the page is mapped into userspace
(raised page_mapcount - though that hints it may be worth keeping the
swap): all that matters is that there be no more references to the swap
(and no writeback in progress).
swapoff (try_to_unuse) has been removing pages from swapcache for years,
with no concern for page count or page mapcount, and we used to have a
comment in lookup_swap_cache() recognizing that: if you go for a page of
swapcache, you'll get the right page, but it could have been removed from
swapcache by the time you get page lock.
So, give up asking for exclusivity: get rid of
remove_exclusive_swap_page(), and remove_exclusive_swap_page_ref() and
remove_exclusive_swap_page_count() which were spawned for the recent LRU
work: replace them by the simpler try_to_free_swap() which just checks
page_swapcount().
Similarly, remove the page_count limitation from free_swap_and_count(),
but assume that it's worth holding on to the swap if page is mapped and
swap nowhere near full. Add a vm_swap_full() test in free_swap_cache()?
It would be consistent, but I think we probably have enough for now.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A good place to free up old swap is where do_wp_page(), or do_swap_page(),
is about to redirty the page: the data on disk is then stale and won't be
read again; and if we do decide to write the page out later, using the
previous swap location makes an unnecessary disk seek very likely.
So give can_share_swap_page() the side-effect of delete_from_swap_cache()
when it safely can. And can_share_swap_page() was always a misleading
name, the more so if it has a side-effect: rename it reuse_swap_page().
Irrelevant cleanup nearby: remove swap_token_default_timeout definition
from swap.h: it's used nowhere.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The swap code is over-provisioned with BUG_ONs on assorted page flags,
mostly dating back to 2.3. They're good documentation, and guard against
developer error, but a waste of space on most systems: change them to
VM_BUG_ONs, conditional on CONFIG_DEBUG_VM. Just delete the PagePrivate
ones: they're later, from 2.5.69, but even less interesting now.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup, code robustization
The __swp_...() macros silently relied upon which bits are used for
_PAGE_FILE and _PAGE_PROTNONE. After having changed _PAGE_PROTNONE in
our Xen kernel to no longer overlap _PAGE_PAT, live locks and crashes
were reported that could have been avoided if these macros properly
used the symbolic constants. Since, as pointed out earlier, for Xen
Dom0 support mainline likewise will need to eliminate the conflict
between _PAGE_PAT and _PAGE_PROTNONE, this patch does all the necessary
adjustments, plus it introduces a mechanism to check consistency
between MAX_SWAPFILES_SHIFT and the actual encoding macros.
This also fixes a latent bug in that x86-64 used a 6-bit mask in
__swp_type(), and if MAX_SWAPFILES_SHIFT was increased beyond 5 in (the
seemingly unrelated) linux/swap.h, this would have resulted in a
collision with _PAGE_FILE.
Non-PAE 32-bit code gets similarly adjusted for its pte_to_pgoff() and
pgoff_to_pte() calculations.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
trylock_page, unlock_page open and close a critical section. Hence,
we can use the lock bitops to get the desired memory ordering.
Also, mark trylock as likely to succeed (and remove the annotation from
callers).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If vm_swap_full() (swap space more than 50% full), the system will free
swap space at swapin time. With this patch, the system will also free the
swap space in the pageout code, when we decide that the page is not a
candidate for swapout (and just wasting swap space).
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: MinChan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converting page lock to new locking bitops requires a change of page flag
operation naming, so we might as well convert it to something nicer
(!TestSetPageLocked_Lock => trylock_page, SetPageLocked => set_page_locked).
This also facilitates lockdeping of page lock.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the following needlessly global code static:
- swap_lock
- nr_swapfiles
- struct swap_list
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mapping->tree_lock has no read lockers. convert the lock from an rwlock
to a spinlock.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vegard Nossum has noticed the ever-decreasing negative priority in a
swapon /swapoff loop, which eventually would misprioritize when int wraps
positive. Not worth spending much code on, but probably better fixed.
It's easy to handle the swapping on and off of just one area, but there's
not much point if a pair or more still misbehave. To handle the general
case, swapoff should compact negative priorities, keeping them always from
-1 to -MAX_SWAPFILES. That's a change, but should cause no regression,
since these negative (unspecified) priorities are disjoint from the the
positive specified priorities 0 to 32767.
One small functional difference, which seems appropriate: when swapoff
fails to free all swap from a negative priority area, that area is now
reinserted at lowest priority, rather than at its original priority.
In moving down swapon's setting of priority, I notice that an area is
visible to /proc/swaps when it has swap_map set, yet that was being set
before all the visible fields were properly filled in: corrected.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create() to make sure that ->proc_fops be setup before gluing PDE to
main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When checking for the swap header try byteswapping the endianess dependent
fields to allow the swap partition to be shared between big & little endian
systems.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
seq_path() is always called with a dentry and a vfsmount from a struct path.
Make seq_path() take it directly as an argument.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch reinstates the "swapoff: scan ptes preemptibly" mod we started
with: in due course it should be rendered down into the earlier patches,
leaving us with a more straightforward mem_cgroup_charge mod to unuse_pte,
allocating with GFP_KERNEL while holding no spinlock and no atomic kmap.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Pavel Emelianov <xemul@openvz.org>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Kirill Korotaev <dev@sw.ru>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: David Rientjes <rientjes@google.com>
Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin pointed out that swap cache and page cache addition routines
could be called from non GFP_KERNEL contexts. This patch makes the
charging routine aware of the gfp context. Charging might fail if the
cgroup is over it's limit, in which case a suitable error is returned.
This patch was tested on a Powerpc box. I am still looking at being able
to test the path, through which allocations happen in non GFP_KERNEL
contexts.
[kamezawa.hiroyu@jp.fujitsu.com: problem with ZONE_MOVABLE]
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Pavel Emelianov <xemul@openvz.org>
Cc: Paul Menage <menage@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Kirill Korotaev <dev@sw.ru>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: David Rientjes <rientjes@google.com>
Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the accounting hooks. The accounting is carried out for RSS and Page
Cache (unmapped) pages. There is now a common limit and accounting for both.
The RSS accounting is accounted at page_add_*_rmap() and page_remove_rmap()
time. Page cache is accounted at add_to_page_cache(),
__delete_from_page_cache(). Swap cache is also accounted for.
Each page's page_cgroup is protected with the last bit of the
page_cgroup pointer, this makes handling of race conditions involving
simultaneous mappings of a page easier. A reference count is kept in the
page_cgroup to deal with cases where a page might be unmapped from the RSS
of all tasks, but still lives in the page cache.
Credits go to Vaidyanathan Srinivasan for helping with reference counting work
of the page cgroup. Almost all of the page cache accounting code has help
from Vaidyanathan Srinivasan.
[hugh@veritas.com: fix swapoff breakage]
[akpm@linux-foundation.org: fix locking]
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Pavel Emelianov <xemul@openvz.org>
Cc: Paul Menage <menage@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Kirill Korotaev <dev@sw.ru>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: David Rientjes <rientjes@google.com>
Cc: <Valdis.Kletnieks@vt.edu>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch precisely reverts the "swapoff: scan ptes preemptibly" patch
just presented. It's a temporary measure to allow existing memory
controller patches to apply without rejects: in due course they should be
rendered down into one sensible patch, and this reversion disappear.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a couple of reasons (patches follow) why it would be good to open a
window for sleep in shmem_unuse_inode, between its search for a matching swap
entry, and its handling of the entry found.
shmem_unuse_inode must then use igrab to hold the inode against deletion in
that window, and its corresponding iput might result in deletion: so it had
better unlock_page before the iput, and might as well release the page too.
Nor is there any need to hold on to shmem_swaplist_mutex once we know we'll
leave the loop. So this unwinding moves from try_to_unuse and shmem_unuse
into shmem_unuse_inode, in the case when it finds a match.
Let try_to_unuse break on error in the shmem_unuse case, as it does in the
unuse_mm case: though at this point in the series, no error to break on.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provided that CONFIG_HIGHPTE is not set, unuse_pte_range can reduce latency
in swapoff by scanning the page table preemptibly: so long as unuse_pte is
careful to recheck that entry under pte lock.
(To tell the truth, this patch was not inspired by any cries for lower
latency here: rather, this restructuring permits a future memory controller
patch to allocate with GFP_KERNEL in unuse_pte, where before it could not.
But it would be wrong to tuck this change away inside a memcgroup patch.)
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Tested-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
valid_swaphandles is supposed to do a quick pass over the swap map entries
neigbouring the entry which swapin_readahead is targetting, to determine for
it a range worth reading all together. But since it always starts its search
from the beginning of the swap "cluster", a reject (free entry) there
immediately curtails the readaround, and every swapin_readahead from that
cluster is for just a single page. Instead scan forwards and backwards around
the target entry.
Use better names for some variables: a swap_info pointer is usually called
"si" not "swapdev". And at the end, if only the target page should be read,
return count of 0 to disable readaround, to avoid the unnecessarily repeated
call to read_swap_cache_async.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building in a filesystem on a loop device on a tmpfs file can hang when
swapping, the loop thread caught in that infamous throttle_vm_writeout.
In theory this is a long standing problem, which I've either never seen in
practice, or long ago suppressed the recollection, after discounting my load
and my tmpfs size as unrealistically high. But now, with the new aops, it has
become easy to hang on one machine.
Loop used to grab_cache_page before the old prepare_write to tmpfs, which
seems to have been enough to free up some memory for any swapin needed; but
the new write_begin lets tmpfs find or allocate the page (much nicer, since
grab_cache_page missed tmpfs pages in swapcache).
When allocating a fresh page, tmpfs respects loop's mapping_gfp_mask, which
has __GFP_IO|__GFP_FS stripped off, and throttle_vm_writeout is designed to
break out when __GFP_IO or GFP_FS is unset; but when tmfps swaps in,
read_swap_cache_async allocates with GFP_HIGHUSER_MOVABLE regardless of the
mapping_gfp_mask - hence the hang.
So, pass gfp_mask down the line from shmem_getpage to shmem_swapin to
swapin_readahead to read_swap_cache_async to add_to_swap_cache.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace CONFIG_SOFTWARE_SUSPEND with CONFIG_HIBERNATION to avoid
confusion (among other things, with CONFIG_SUSPEND introduced in the
next patch).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the shrink_list name on some files under mm/ directory.
Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ensure pages are uptodate after returning from read_cache_page, which allows
us to cut out most of the filesystem-internal PageUptodate calls.
I didn't have a great look down the call chains, but this appears to fixes 7
possible use-before uptodate in hfs, 2 in hfsplus, 1 in jfs, a few in
ecryptfs, 1 in jffs2, and a possible cleared data overwritten with readpage in
block2mtd. All depending on whether the filler is async and/or can return
with a !uptodate page.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the kernels later than 2.6.19 there is a regression that makes swsusp
fail if the resume device is not explicitly specified.
It can be fixed by adding an additional parameter to
mm/swapfile.c:swap_type_of() allowing us to pass the (struct block_device
*) corresponding to the first available swap back to the caller.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change all the uses of f_{dentry,vfsmnt} to f_path.{dentry,mnt} in linux/mm/.
Signed-off-by: Josef "Jeff" Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- move some file_operations structs into the .rodata section
- move static strings from policy_types[] array into the .rodata section
- fix generic seq_operations usages, so that those structs may be defined
as "const" as well
[akpm@osdl.org: couple of fixes]
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make swsusp use block device offsets instead of swap offsets to identify swap
locations and make it use the same code paths for writing as well as for
reading data.
This allows us to use the same code for handling swap files and swap
partitions and to simplify the code, eg. by dropping rw_swap_page_sync().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Heiko Carstens
KAMEZAWA Hiroyuki
KOSAKI Motohiro
Hugh Dickins
Jan Beulich
Nick Piggin
Rik van Riel
Fernando Luis Vazquez Cao
Adrian Bunk
Denis V. Lunev
Chris Dearman
Jan Blunck
Balbir Singh
Rafael J. Wysocki
Anderson Briglia
Josef "Jeff" Sipek
Helge Deller