The DT-based panel capabilities selection was picking up
a subset of available modes based on hardware configuration.
This was wrong, as the capabilities describe available
memory models and adapt the display controller to them
that the RGB output is wired up correctly (as in: R and
B components are not swapped).
This patch fixes it by removing the unnecessary limitation.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When looking at this driver for a client, I noticed the code that
configures the HSYNC pulse clobbers the display width in the same
register. It only preserves the MS part of the width in bit 3 and zeros
the LS part of the width in bits 9 to 4. This doesn't matter during
initialization as the width is configured afterwards, but subsequent use
of the FBIPUT_HSYNC ioctl would clobber the width.
Preserve bits 9 to 0 of LCD_RASTER_TIMING_0_REG when configuring the
horizontal sync.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Convert a zero return value on error to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the device-tree specifies a max-memory-bandwidth property then the
CLCD driver uses that to calculate the bits-per-pixel supported,
however, this calculation is faulty for two reasons.
1. It doesn't ensure that the result is a sane value, i.e. a power of 2
and <= 32 as the rest of the code assumes.
2. It uses the displayed resolution and calculates the average bandwidth
across the whole frame. It should instead calculate the peak
bandwidth based on the pixel clock.
This patch fixes both the above.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix build failure caused as follows:
The function chipsfb_pci_init() references
the function __init chips_hw_init().
This is often because chipsfb_pci_init lacks a __init
annotation or the annotation of chips_hw_init is wrong.
make: *** [drivers] Error 2
by removing the __init annotation from chips_hw_init(). The other thing that
could have been done was annotating chipsfb_pci_init(). But that cannot be done
since chipsfb_pci_init() is called from non __init functions.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* Much better HDMI infoframe support for OMAP
* Cirrus Logic CLPS711X framebuffer driver
* DT support for PL11x CLCD driver
* Various small fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gXX+
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
After v3.16-rc1, devices populated with of_platform_populate() should be
depopulated using of_platform_depopulate(). Failure to do so prevents
the devices from being populated again (e.g. when loading a module).
This patch fixes the problem for the OMAP DSI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
We don't want random users to be able to spam the logs, and commit
37549e94c7 (sysfs: disallow
world-writable files.) finally makes this a build error.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently the VSC has no chance to notify the VSP of the dirty rectangle on VM
panic because the notification work is done in a workqueue, and in panic() the
kernel typically ends up in an infinite loop, and a typical kernel config has
CONFIG_PREEMPT_VOLUNTARY=y and CONFIG_PREEMPT is not set, so a context switch
can't happen in panic() and the workqueue won't have a chance to run. As a
result, the VM Connection window can't refresh until it's closed and we
re-connect to the VM.
We can register a handler on panic_notifier_list: the handler can notify
the VSC and switch the framebuffer driver to a "synchronous mode", meaning
the VSC flushes any future framebuffer change to the VSP immediately.
v2: removed the MS-TFS line in the commit message
v3: remove some 'unlikely' markings
v4: avoid global variables as Tomi Valkeinen suggested
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch fixes the following error when !CONFIG_OF:
drivers/video/fbdev/amba-clcd.c:800:54: warning: ‘struct amba_dev’ declared inside parameter list [enabled by default]
static struct clcd_board *clcdfb_of_get_board(struct amba_dev *dev)
^
and adds a missing Kconfig select causing this
when CONFIG_OF && !CONFIG_FB_MODE_HELPERS:
drivers/video/fbdev/amba-clcd.c:567: undefined reference to `fb_videomode_from_videomode'
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the clock framework to en/disable the clock to the au1100
framebuffer device.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7474/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes all absolute SYS_XY registers to offsets from the
SYS block base, prefixes them with AU1000 to avoid silent failures due
to changed addresses, and introduces helper functions to read/write
them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7464/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code has a variable to change the polarity of the PWM backlight control but
it was not being initialized. This patch adds a devicetree entry to set the
variable if required.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds basic DT bindings for the PL11x CLCD cells
and make their fbdev driver use them.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The Versatile CLCD helpers call dma_alloc_writecombine() which is only
available on ARM and AVR32, meaning they won't build on other platforms
including arm64. Unfortunately the current Kconfig enables the symbol
by default if ARCH_VEXPRESS is defined which means that it is enabled on
arm64 when building for the ARM reference platforms and models for ARMv8
since they have many hardware similarities with their pre-ARMv8 systems.
Since all the systems that need the helpers are ARM systems fix this by
adding a dependency on ARM.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
commit 11c32d7b62 ("video: move Versatile CLCD helpers")
moved files out of the plat-versatile directory but in the process
got a few of the dependencies wrong:
- If CONFIG_FB is not set, the file no longer gets built, resulting
in a link error
- If CONFIG_FB or CONFIG_FB_ARMCLCD are disabled, we also get a
Kconfig warning for incorrect dependencies due to the symbol
being 'select'ed from the platform Kconfig.
- When the file is not built, we also get a link error for missing
symbols.
This patch should fix all three, by removing the 'select' statements,
changing the Kconfig description of the symbol to be enabled in
exactly the right configurations, and adding inline stub functions
for the case when the framebuffer driver is disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
some constification from static code analysis.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTvm0dAAoJEEEQszewGV1z0+QQALK+SJvPRMum4lBaorNmmdQs
2rz760astlUwGqojk4Fd3YilkQobXTe9Tv4tQiMb7p6XSbuktSYPZzGzG4EHarwn
nyWxJSTdXNwljEg1LykwddTin1MBLxWpUyPb8IKoebcO1Bsxz93pdVqkViiiUfgi
8auTQRCzt2bSRtYq2wLq7tot6vMW2thI7f8TtayXJEA+MkuDEx+F280dnpyJrXVM
+dxzYwJVfe3wjPuJ2cL8tkib4FbPftlv/jgj4RpegFqzmxQkzcPxEm53IW8rhuZH
R6LxRiqPvHvCtaXYQYbqhSa2DODIH2hNIUo2VgX8dOEFHbz5Ti72V4dVV3rdhRUJ
EM5EnI30kStB/qA9pY1nmGYybnmZlUzeouzy/DbwPAl5kW1+EieXPQXtsLYDBMFm
Tz09Hw+xLq+iqBOOreu2ohpcrUEsbSPiV5fx5K93G2/wcxOTBoO5UAlWpYhDaYTD
aP5u7YQEubgwk2Pqggs3NJxfwISUflw7m+V628Zqr2g3+g3UvBHDTxN7/6qDraVa
IgpnYLDUEnDmgPFjdTT5Ybcgs2D4uSo6xTN+O4F1AcKbE2G56x9Qt6YUvyPZalyH
elQc9egDvZkVt1eO/HWW1qfmEU2LYaXsJYxhIjkxKQ0GdFq4E2IKq+0Ydz5p0omG
2NGSFWxlTgqN/I0zWPbD
=OmbF
-----END PGP SIGNATURE-----
Merge tag 'ux500-core-for-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
Merge "Ux500 core changes for v3.17 take 1" from Linus Walleij:
Some minor cleanups to the Ux500 core. DT-only probe path and
some constification from static code analysis.
* tag 'ux500-core-for-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: remove pointless cache setup complexity
ARM: ux500: storage class should be before const qualifier
ARM: ux500: Staticize ab8505_regulators
ARM: ux500: Staticize local symbols in cpu-db8500.c
ARM: ux500: Staticise ux500_soc_attr
+ Linux 3.16-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
- removing s5p64x0 SoCs and s5pc100 SoC in mainline because
no more user and if it is required next time, it will be
supported with DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CFpb
-----END PGP SIGNATURE-----
Merge tag 's5p-cleanup-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
Merge "Samsung cleanup 2nd version for S5P SoCs for 3.17" from Kukjin Kim:
Cleanup S5P SoCs for 3.17
- removing s5p64x0 SoCs and s5pc100 SoC in mainline because
no more user and if it is required next time, it will be
supported with DT.
* tag 's5p-cleanup-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
video: fbdev: s3c-fb: remove s5pc100 related fimd and fb codes
mtd: onenand: remove s5pc100 related onenand codes
spi: s3c64xx: remove s5pc100 related spi codes
gpio: samsung: remov s5pc100 related gpio codes
ARM: S5PC100: no more support S5PC100 SoC
video: fbdev: s3c-fb: remove s5p64x0 related fimd codes
spi: s3c64xx: remove s5p64x0 related spi codes
gpio: samsung: remove s5p64x0 related gpio codes
ARM: S5P64X0: no more support S5P6440 and S5P6450 SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch removes fimd and fb codes for s5pc100 SoC.
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes fimd codes for s5p6440 and s5p6450 SoCs.
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit b4aa016305 ("efifb: Implement vga_default_device() (v2)") added
efifb vga_default_device() so EFI systems that do not load shadow VBIOS or
setup VGA get proper value for boot_vga PCI sysfs attribute on the
corresponding PCI device.
Xorg doesn't detect devices when boot_vga=0, e.g., on some EFI systems such
as MacBookAir2,1. Xorg detects the GPU and finds the DRI device but then
bails out with "no devices detected".
Note: When vga_default_device() is set boot_vga PCI sysfs attribute
reflects its state. When unset this attribute is 1 whenever
IORESOURCE_ROM_SHADOW flag is set.
With introduction of sysfb/simplefb/simpledrm efifb is getting obsolete
while having native drivers for the GPU also makes selecting sysfb/efifb
optional.
Remove the efifb implementation of vga_default_device() and initialize
vgaarb's vga_default_device() with the PCI GPU that matches boot
screen_info in pci_fixup_video().
[bhelgaas: remove unused "dev" in efifb_setup()]
Fixes: b4aa016305 ("efifb: Implement vga_default_device() (v2)")
Tested-by: Anibal Francisco Martinez Cortina <linuxkid.zeuz@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
CC: stable@vger.kernel.org # v3.5+
We no longer need the horrible driver internal videmode tables, which
were used to decide if a given videomode is a HDMI or DVI mode. So
remove all related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using hardcoded AVI infoframe, and a custom HDMI/DVI mode
selection based in internal videomode tables, add support to set the
infoframe and HDMI/DVI mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using hardcoded AVI infoframe, and a custom HDMI/DVI mode
selection based in internal videomode tables, add support to set the
infoframe and HDMI/DVI mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add infoframe and hdmi_dvi_mode fields to 'struct hdmi_config' which
will be used in the following patches for OMAP4 and OMAP5 HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add pass-through functions for set_infoframe and set_hdmi_mode to
hdmi-connector and tpd12s015 drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We now use the common AVI infoframe support, so the OMAP specific AVI
infoframe code can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using OMAP specific AVI infoframe structs, use the common one
from include/linux/hdmi.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using OMAP specific AVI infoframe structs, use the common one
from include/linux/hdmi.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP HDMI driver has an 'enum hdmi_audio_sample_size', which conflicts
with the common include/linux/hdmi.h.
Change the name of the OMAP specific enum with '_omap" postfix.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_timings_ok() is a bit confusing how it handles the return
value.
Change the function to just return immediately when a timing is deemed
not valid, making the code much easier to follow.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP2/3 does not support interlace for LCD out. OMAP4+ does, but is not
supported by the driver at the moment.
The driver still accepts interlaced mode for LCD out, causing broken
display output.
This patch makes dispc reject interlace for LCD out.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch fixes building CLPS711X FB driver if the framebuffer
core is used as a module.
LD init/built-in.o
drivers/built-in.o: In function `clps711x_fb_remove':
:(.text+0x44a8): undefined reference to `unregister_framebuffer'
drivers/built-in.o: In function `clps711x_fb_probe':
:(.text+0x44cc): undefined reference to `fb_get_options'
:(.text+0x45d8): undefined reference to `fb_alloc_cmap'
:(.text+0x45e4): undefined reference to `register_framebuffer'
make: *** [vmlinux] Error 1
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use clk_prepare_enable/clk_disable_unprepare to make the driver
work properly with common clock framework.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The surrounding code and the fact that the previous two if's are
rendered useless without this "else" (since SIS_340==55 and XGI_20==75
are greater than SIS_661==15) suggests that the "else" is indeed
missing.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Checkpatch.pl worries that we have left off the conditional bit because
it isn't indented correctly.
WARNING: suspect code indent for conditional statements (24, 24)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit f8bd493456 by Jingoo Han
introduced this problem. This makes bfin_adv7393fb.c failed to compile.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pawel Moll
Ian Abbott
Julia Lawall
Jon Medhurst (Tixy)
Pranith Kumar
Benoit Taine
Linus Torvalds
Tomi Valkeinen
Rusty Russell
Dexuan Cui
Manuel Lauss
Michael Welling
Mark Brown
Arnd Bergmann
Olof Johansson
Kukjin Kim
Bruno Prémont
Alexander Shiyan
Vasily Khoruzhick
Rasmus Villemoes
Joe Perches
Dan Carpenter
Scott Jiang