Граф коммитов

181 Коммитов

Автор SHA1 Сообщение Дата
Johannes Weiner 72835c86ca mm: unify remaining mem_cont, mem, etc. variable names to memcg
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-01-12 20:13:06 -08:00
Mel Gorman f90ac3982a mm: avoid livelock on !__GFP_FS allocations
Colin Cross reported;

  Under the following conditions, __alloc_pages_slowpath can loop forever:
  gfp_mask & __GFP_WAIT is true
  gfp_mask & __GFP_FS is false
  reclaim and compaction make no progress
  order <= PAGE_ALLOC_COSTLY_ORDER

  These conditions happen very often during suspend and resume,
  when pm_restrict_gfp_mask() effectively converts all GFP_KERNEL
  allocations into __GFP_WAIT.

  The oom killer is not run because gfp_mask & __GFP_FS is false,
  but should_alloc_retry will always return true when order is less
  than PAGE_ALLOC_COSTLY_ORDER.

In his fix, he avoided retrying the allocation if reclaim made no progress
and __GFP_FS was not set.  The problem is that this would result in
GFP_NOIO allocations failing that previously succeeded which would be very
unfortunate.

The big difference between GFP_NOIO and suspend converting GFP_KERNEL to
behave like GFP_NOIO is that normally flushers will be cleaning pages and
kswapd reclaims pages allowing GFP_NOIO to succeed after a short delay.
The same does not necessarily apply during suspend as the storage device
may be suspended.

This patch special cases the suspend case to fail the page allocation if
reclaim cannot make progress and adds some documentation on how
gfp_allowed_mask is currently used.  Failing allocations like this may
cause suspend to abort but that is better than a livelock.

[mgorman@suse.de: Rework fix to be suspend specific]
[rientjes@google.com: Move suspended device check to should_alloc_retry]
Reported-by: Colin Cross <ccross@android.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-01-10 16:30:42 -08:00
Linus Torvalds 32aaeffbd4 Merge branch 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
  Revert "tracing: Include module.h in define_trace.h"
  irq: don't put module.h into irq.h for tracking irqgen modules.
  bluetooth: macroize two small inlines to avoid module.h
  ip_vs.h: fix implicit use of module_get/module_put from module.h
  nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
  include: replace linux/module.h with "struct module" wherever possible
  include: convert various register fcns to macros to avoid include chaining
  crypto.h: remove unused crypto_tfm_alg_modname() inline
  uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
  pm_runtime.h: explicitly requires notifier.h
  linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
  miscdevice.h: fix up implicit use of lists and types
  stop_machine.h: fix implicit use of smp.h for smp_processor_id
  of: fix implicit use of errno.h in include/linux/of.h
  of_platform.h: delete needless include <linux/module.h>
  acpi: remove module.h include from platform/aclinux.h
  miscdevice.h: delete unnecessary inclusion of module.h
  device_cgroup.h: delete needless include <linux/module.h>
  net: sch_generic remove redundant use of <linux/module.h>
  net: inet_timewait_sock doesnt need <linux/module.h>
  ...

Fix up trivial conflicts (other header files, and  removal of the ab3550 mfd driver) in
 - drivers/media/dvb/frontends/dibx000_common.c
 - drivers/media/video/{mt9m111.c,ov6650.c}
 - drivers/mfd/ab3550-core.c
 - include/linux/dmaengine.h
2011-11-06 19:44:47 -08:00
David Rientjes 43362a4977 oom: fix race while temporarily setting current's oom_score_adj
test_set_oom_score_adj() was introduced in 72788c3856 ("oom: replace
PF_OOM_ORIGIN with toggling oom_score_adj") to temporarily elevate
current's oom_score_adj for ksm and swapoff without requiring an
additional per-process flag.

Using that function to both set oom_score_adj to OOM_SCORE_ADJ_MAX and
then reinstate the previous value is racy since it's possible that
userspace can set the value to something else itself before the old value
is reinstated.  That results in userspace setting current's oom_score_adj
to a different value and then the kernel immediately setting it back to
its previous value without notification.

To fix this, a new compare_swap_oom_score_adj() function is introduced
with the same semantics as the compare and swap CAS instruction, or
CMPXCHG on x86.  It is used to reinstate the previous value of
oom_score_adj if and only if the present value is the same as the old
value.

Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-10-31 17:30:45 -07:00
Paul Gortmaker e25934a517 mm: delete various needless include <linux/module.h>
There is nothing modular in these files, and no reason to drag
in all the 357 headers that module.h brings with it, since
it just slows down compiles.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 09:20:11 -04:00
Hugh Dickins a2c16d6cb0 mm: let swap use exceptional entries
If swap entries are to be stored along with struct page pointers in a
radix tree, they need to be distinguished as exceptional entries.

Most of the handling of swap entries in radix tree will be contained in
shmem.c, but a few functions in filemap.c's common code need to check
for their appearance: find_get_page(), find_lock_page(),
find_get_pages() and find_get_pages_contig().

So as not to slow their fast paths, tuck those checks inside the
existing checks for unlikely radix_tree_deref_slot(); except for
find_lock_page(), where it is an added test.  And make it a BUG in
find_get_pages_tag(), which is not applied to tmpfs files.

A part of the reason for eliminating shmem_readpage() earlier, was to
minimize the places where common code would need to allow for swap
entries.

The swp_entry_t known to swapfile.c must be massaged into a slightly
different form when stored in the radix tree, just as it gets massaged
into a pte_t when stored in page tables.

In an i386 kernel this limits its information (type and page offset) to
30 bits: given 32 "types" of swapfile and 4kB pagesize, that's a maximum
swapfile size of 128GB.  Which is less than the 512GB we previously
allowed with X86_PAE (where the swap entry can occupy the entire upper
32 bits of a pte_t), but not a new limitation on 32-bit without PAE; and
there's not a new limitation on 64-bit (where swap filesize is already
limited to 16TB by a 32-bit page offset).  Thirty areas of 128GB is
probably still enough swap for a 64GB 32-bit machine.

Provide swp_to_radix_entry() and radix_to_swp_entry() conversions, and
enforce filesize limit in read_swap_header(), just as for ptes.

Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-08-03 14:25:22 -10:00
Kay Sievers f15146380d fs: seq_file - add event counter to simplify poll() support
Moving the event counter into the dynamically allocated 'struc seq_file'
allows poll() support without the need to allocate its own tracking
structure.

All current users are switched over to use the new counter.

Requested-by: Andrew Morton akpm@linux-foundation.org
Acked-by: NeilBrown <neilb@suse.de>
Tested-by: Lucas De Marchi lucas.demarchi@profusion.mobi
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2011-07-20 20:47:50 -04:00
Hugh Dickins 072441e21d mm: move shmem prototypes to shmem_fs.h
Before adding any more global entry points into shmem.c, gather such
prototypes into shmem_fs.h.  Remove mm's own declarations from swap.h,
but for now leave the ones in mm.h: because shmem_file_setup() and
shmem_zero_setup() are called from various places, and we should not
force other subsystems to update immediately.

Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-06-27 18:00:12 -07:00
David Rientjes 72788c3856 oom: replace PF_OOM_ORIGIN with toggling oom_score_adj
There's a kernel-wide shortage of per-process flags, so it's always
helpful to trim one when possible without incurring a significant penalty.
 It's even more important when you're planning on adding a per- process
flag yourself, which I plan to do shortly for transparent hugepages.

PF_OOM_ORIGIN is used by ksm and swapoff to prefer current since it has a
tendency to allocate large amounts of memory and should be preferred for
killing over other tasks.  We'd rather immediately kill the task making
the errant syscall rather than penalizing an innocent task.

This patch removes PF_OOM_ORIGIN since its behavior is equivalent to
setting the process's oom_score_adj to OOM_SCORE_ADJ_MAX.

The process's old oom_score_adj is stored and then set to
OOM_SCORE_ADJ_MAX during the time it used to have PF_OOM_ORIGIN.  The old
value is then reinstated when the process should no longer be considered a
high priority for oom killing.

Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Izik Eidus <ieidus@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-05-25 08:39:10 -07:00
Linus Torvalds 6c51038900 Merge branch 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
  Documentation/iostats.txt: bit-size reference etc.
  cfq-iosched: removing unnecessary think time checking
  cfq-iosched: Don't clear queue stats when preempt.
  blk-throttle: Reset group slice when limits are changed
  blk-cgroup: Only give unaccounted_time under debug
  cfq-iosched: Don't set active queue in preempt
  block: fix non-atomic access to genhd inflight structures
  block: attempt to merge with existing requests on plug flush
  block: NULL dereference on error path in __blkdev_get()
  cfq-iosched: Don't update group weights when on service tree
  fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
  block: Require subsystems to explicitly allocate bio_set integrity mempool
  jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
  jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
  fs: make fsync_buffers_list() plug
  mm: make generic_writepages() use plugging
  blk-cgroup: Add unaccounted time to timeslice_used.
  block: fixup plugging stubs for !CONFIG_BLOCK
  block: remove obsolete comments for blkdev_issue_zeroout.
  blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
  ...

Fix up conflicts in fs/{aio.c,super.c}
2011-03-24 10:16:26 -07:00
KAMEZAWA Hiroyuki 56039efa18 memcg: fix ugly initialization of return value is in caller
Remove initialization of vaiable in caller of memory cgroup function.
Actually, it's return value of memcg function but it's initialized in
caller.

Some memory cgroup uses following style to bring the result of start
function to the end function for avoiding races.

   mem_cgroup_start_A(&(*ptr))
   /* Something very complicated can happen here. */
   mem_cgroup_end_A(*ptr)

In some calls, *ptr should be initialized to NULL be caller.  But it's
ugly.  This patch fixes that *ptr is initialized by _start function.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 19:46:22 -07:00
Cesar Eduardo Barros 2130781e2a sys_swapon: fix inode locking
A conflict between 52c50567d8 ("mm: swap: unlock swapfile inode mutex
before closing file on bad swapfiles") and 83ef99befc ("sys_swapon:
remove did_down variable") caused a double unlock of the inode mutex
(once in bad_swap: before the filp_close, once at the end just before
returning).

The patch which added the extra unlock cleared did_down to avoid
unlocking twice, but the other patch removed the did_down variable.

To fix, set inode to NULL after the first unlock, since it will be used
after that point only for the final unlock.

While checking this patch, I found a path which could unlock without
locking, in case the same inode was added as a swapfile twice. To fix,
move the setting of the inode variable further down, to just before
claim_swapfile, which will lock the inode before doing anything else.

Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 07:54:22 -07:00
Cesar Eduardo Barros 24b8ff7c27 mm: remove inline from scan_swap_map()
scan_swap_map() is a large function (224 lines), with several loops and a
complex control flow involving several gotos.

Given all that, it is a bit silly that it is marked as inline.  The
compiler agrees with me: on a x86-64 compile, it did not inline the
function.

Remove the "inline" and let the compiler decide instead.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:09 -07:00
Cesar Eduardo Barros 40531542e2 sys_swapon: separate final enabling of the swapfile
The block in sys_swapon which does the final adjustments to the
swap_info_struct and to swap_list is the same as the block which
re-inserts it again at sys_swapoff on failure of try_to_unuse(). Move
this code to a separate function, and use it both in sys_swapon and
sys_swapoff.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:08 -07:00
Cesar Eduardo Barros c6a2b64ba5 sys_swapoff: change order to match sys_swapon
The block in sys_swapon which does the final adjustments to the
swap_info_struct and to swap_list is the same as the block which
re-inserts it again at sys_swapoff on failure of try_to_unuse(), except
for the order of the operations within the lock. Since the order should
not matter, arbitrarily change sys_swapoff to match sys_swapon, in
preparation to making both share the same code.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:08 -07:00
Cesar Eduardo Barros c69dbfb84e sys_swapon: move printk outside lock
The block in sys_swapon which does the final adjustments to the
swap_info_struct and to swap_list is the same as the block which
re-inserts it again at sys_swapoff on failure of try_to_unuse(). To be
able to make both share the same code, move the printk() call in the
middle of it to just after it.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:08 -07:00
Cesar Eduardo Barros 9c8100ef26 sys_swapon: remove nr_good_pages variable
It still exists within setup_swap_map_and_extents(), but after it
nr_good_pages == p->pages.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:08 -07:00
Cesar Eduardo Barros bdb8e3f683 sys_swapon: simplify error flow in setup_swap_map_and_extents()
Since there is no cleanup to do, there is no reason to jump to a label.
Return directly instead.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:08 -07:00
Cesar Eduardo Barros 915d4d7bc0 sys_swapon: separate parsing of bad blocks and extents
Move the code which parses the bad block list and the extents to a
separate function. Only code movement, no functional changes.

This change uses the fact that, after the success path, nr_good_pages ==
p->pages.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:08 -07:00
Cesar Eduardo Barros 1421ef3cd1 sys_swapon: call swap_cgroup_swapon() earlier
The call to swap_cgroup_swapon is in the middle of loading the swap map
and extents. As it only does memory allocation and does not depend on
the swapfile layout (map/extents), it can be called earlier (or later).

Move it to just after the allocation of swap_map, since it is
conceptually similar (allocates a map).

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:08 -07:00
Cesar Eduardo Barros 3871902538 sys_swapon: simplify error flow in read_swap_header()
Since there is no cleanup to do, there is no reason to jump to a label.
Return directly instead.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:08 -07:00
Cesar Eduardo Barros ca8bd38bf6 sys_swapon: separate parsing of swapfile header
Move the code which parses and checks the swapfile header (except for
the bad block list) to a separate function. Only code movement, no
functional changes.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros 5de771e41f sys_swapon: move setting of swapfilepages near use
There is no reason I can see to read inode->i_size long before it is
needed. Move its read to just before it is needed, to reduce the
variable lifetime.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros 87ade72a79 sys_swapon: simplify error flow in claim_swapfile()
Since there is no cleanup to do, there is no reason to jump to a label.
Return directly instead.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros 4d0e1e1075 sys_swapon: separate bdev claim and inode lock
Move the code which claims the bdev (S_ISBLK) or locks the inode
(S_ISREG) to a separate function. Only code movement, no functional
changes.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros bd69010b04 sys_swapon: use a single error label
sys_swapon currently has two error labels, bad_swap and bad_swap_2.
bad_swap does the same as bad_swap_2 plus destroy_swap_extents() and
swap_cgroup_swapoff(); both are noops in the places where bad_swap_2 is
jumped to. With a single extra test for inode (matching the one in the
S_ISREG case below), all the error paths in the function can go to
bad_swap.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros 9b01c350af sys_swapon: do only cleanup in the cleanup blocks
The only way error is 0 in the cleanup blocks is when the function is
returning successfully. In this case, the cleanup blocks were setting
S_SWAPFILE in the S_ISREG case. But this is not a cleanup.

Move the setting of S_SWAPFILE to just before the "goto out;" to make
this more clear. At this point, we do not need to test for inode because
it will never be NULL.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros f2090d2df5 sys_swapon: remove bdev variable
The bdev variable is always equivalent to (S_ISBLK(inode->i_mode) ?
p->bdev : NULL), as long as it being set is moved to a bit earlier. Use
this fact to remove the bdev variable.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros 7de7fb6b34 sys_swapon: move setting of error nearer use
Move the setting of the error variable nearer the goto in a few places.

Avoids calling PTR_ERR() if not IS_ERR() in two places, and makes the
error condition more explicit in two other places.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros 83ef99befc sys_swapon: remove did_down variable
Since mutex_lock(&inode->i_mutex) is called just after setting inode,
did_down is always equivalent to (inode && S_ISREG(inode->i_mode)).

Use this fact to remove the did_down variable.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros 28b36bd741 sys_swapon: remove initial value of name variable
Now there is nothing which jumps to the cleanup blocks before the name
variable is set. There is no need to set it initially to NULL anymore.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:07 -07:00
Cesar Eduardo Barros 730c0581c8 sys_swapon: simplify error flow in alloc_swap_info()
Since there is no cleanup to do, there is no reason to jump to a label.
Return directly instead.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:06 -07:00
Cesar Eduardo Barros 2542e5134d sys_swapon: simplify error return from swap_info allocation
At this point in sys_swapon, there is nothing to free. Return directly
instead of jumping to the cleanup block at the end of the function.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:06 -07:00
Cesar Eduardo Barros 53cbb2435f sys_swapon: separate swap_info allocation
Move the swap_info allocation to its own function. Only code movement,
no functional changes.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:06 -07:00
Cesar Eduardo Barros e8e6c2ec40 sys_swapon: do not depend on "type" after allocation
Within sys_swapon, after the swap_info entry has been allocated, we
always have type == p->type and swap_info[type] == p. Use this fact to
reduce the dependency on the "type" local variable within the function,
as a preparation to move the allocation of the swap_info entry to a
separate function.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujisu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:06 -07:00
Cesar Eduardo Barros 80b0df12b8 sys_swapon: remove changelog from function comment
Changelogs belong in the git history instead of in the source code.

Also, "The swapon system call" is redundant with
"SYSCALL_DEFINE2(swapon, ...)".

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Gaah. That's a _historical_ comment. But the patch-series depends on removal ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:05 -07:00
Cesar Eduardo Barros 803d0c8351 sys_swapon: use vzalloc() instead of vmalloc/memset
This patch series refactors the sys_swapon function.

sys_swapon is currently a very large function, with 313 lines (more than
12 25-line screens), which can make it a bit hard to read. This patch
series reduces this size by half, by extracting large chunks of related
code to new helper functions.

One of these chunks of code was nearly identical to the part of
sys_swapoff which is used in case of a failure return from
try_to_unuse(), so this patch series also makes both share the same
code.

As a side effect of all this refactoring, the compiled code gets a bit
smaller (from v1 of this patch series):

   text       data        bss        dec        hex    filename
  14012        944        276      15232       3b80    mm/swapfile.o.before
  13941        944        276      15161       3b39    mm/swapfile.o.after

This patch:

Use vzalloc() instead of vmalloc/memset.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Acked-by: Eric B Munson <emunson@mgebm.net>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:44:05 -07:00
Mel Gorman 52c50567d8 mm: swap: unlock swapfile inode mutex before closing file on bad swapfiles
If an administrator tries to swapon a file backed by NFS, the inode mutex is
taken (as it is for any swapfile) but later identified to be a bad swapfile
due to the lack of bmap and tries to cleanup. During cleanup, an attempt is
made to close the file but with inode->i_mutex still held. Closing an NFS
file syncs it which tries to acquire the inode mutex leading to deadlock. If
lockdep is enabled the following appears on the console;

    =============================================
    [ INFO: possible recursive locking detected ]
    2.6.38-rc8-autobuild #1
    ---------------------------------------------
    swapon/2192 is trying to acquire lock:
     (&sb->s_type->i_mutex_key#13){+.+.+.}, at: vfs_fsync_range+0x47/0x7c

    but task is already holding lock:
     (&sb->s_type->i_mutex_key#13){+.+.+.}, at: sys_swapon+0x28d/0xae7

    other info that might help us debug this:
    1 lock held by swapon/2192:
     #0:  (&sb->s_type->i_mutex_key#13){+.+.+.}, at: sys_swapon+0x28d/0xae7

    stack backtrace:
    Pid: 2192, comm: swapon Not tainted 2.6.38-rc8-autobuild #1
    Call Trace:
        __lock_acquire+0x2eb/0x1623
        find_get_pages_tag+0x14a/0x174
        pagevec_lookup_tag+0x25/0x2e
        vfs_fsync_range+0x47/0x7c
        lock_acquire+0xd3/0x100
        vfs_fsync_range+0x47/0x7c
        nfs_flush_one+0x0/0xdf [nfs]
        mutex_lock_nested+0x40/0x2b1
        vfs_fsync_range+0x47/0x7c
        vfs_fsync_range+0x47/0x7c
        vfs_fsync+0x1c/0x1e
        nfs_file_flush+0x64/0x69 [nfs]
        filp_close+0x43/0x72
        sys_swapon+0xa39/0xae7
        sysret_check+0x2e/0x69
        system_call_fastpath+0x16/0x1b

This patch releases the mutex if its held before calling filep_close()
so swapon fails as expected without deadlock when the swapfile is backed
by NFS.  If accepted for 2.6.39, it should also be considered a -stable
candidate for 2.6.38 and 2.6.37.

Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: <stable@kernel.org>		[2.6.37+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-22 17:43:58 -07:00
Jens Axboe 4c63f5646e Merge branch 'for-2.6.39/stack-plug' into for-2.6.39/core
Conflicts:
	block/blk-core.c
	block/blk-flush.c
	drivers/md/raid1.c
	drivers/md/raid10.c
	drivers/md/raid5.c
	fs/nilfs2/btnode.c
	fs/nilfs2/mdt.c

Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-03-10 08:58:35 +01:00
Jens Axboe 7eaceaccab block: remove per-queue plugging
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().

Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-03-10 08:52:07 +01:00
Miklos Szeredi 8074b26f67 mm: fix refcounting in swapon
Grab a reference to bdev before calling blkdev_get(), which expects
the refcount to be already incremented and either returns success or
decrements the refcount and returns an error.

The bug was introduced by e525fd89 (block: make blkdev_get/put()
handle exclusive access), which didn't take into account this behavior
of blkdev_get().

Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-02-24 08:55:01 -08:00
Andrea Arcangeli 3f04f62f90 thp: split_huge_page paging
Paging logic that splits the page before it is unmapped and added to swap
to ensure backwards compatibility with the legacy swap code.  Eventually
swap should natively pageout the hugepages to increase performance and
decrease seeking and fragmentation of swap space.  swapoff can just skip
over huge pmd as they cannot be part of swap yet.  In add_to_swap be
careful to split the page only if we got a valid swap entry so we don't
split hugepages with a full swap.

In theory we could split pages before isolating them during the lru scan,
but for khugepaged to be safe, I'm relying on either mmap_sem write mode,
or PG_lock taken, so split_huge_page has to run either with mmap_sem
read/write mode or PG_lock taken.  Calling it from isolate_lru_page would
make locking more complicated, in addition to that split_huge_page would
deadlock if called by __isolate_lru_page because it has to take the lru
lock to add the tail pages.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-01-13 17:32:41 -08:00
Tejun Heo e525fd89d3 block: make blkdev_get/put() handle exclusive access
Over time, block layer has accumulated a set of APIs dealing with bdev
open, close, claim and release.

* blkdev_get/put() are the primary open and close functions.

* bd_claim/release() deal with exclusive open.

* open/close_bdev_exclusive() are combination of open and claim and
  the other way around, respectively.

* bd_link/unlink_disk_holder() to create and remove holder/slave
  symlinks.

* open_by_devnum() wraps bdget() + blkdev_get().

The interface is a bit confusing and the decoupling of open and claim
makes it impossible to properly guarantee exclusive access as
in-kernel open + claim sequence can disturb the existing exclusive
open even before the block layer knows the current open if for another
exclusive access.  Reorganize the interface such that,

* blkdev_get() is extended to include exclusive access management.
  @holder argument is added and, if is @FMODE_EXCL specified, it will
  gain exclusive access atomically w.r.t. other exclusive accesses.

* blkdev_put() is similarly extended.  It now takes @mode argument and
  if @FMODE_EXCL is set, it releases an exclusive access.  Also, when
  the last exclusive claim is released, the holder/slave symlinks are
  removed automatically.

* bd_claim/release() and close_bdev_exclusive() are no longer
  necessary and either made static or removed.

* bd_link_disk_holder() remains the same but bd_unlink_disk_holder()
  is no longer necessary and removed.

* open_bdev_exclusive() becomes a simple wrapper around lookup_bdev()
  and blkdev_get().  It also has an unexpected extra bdev_read_only()
  test which probably should be moved into blkdev_get().

* open_by_devnum() is modified to take @holder argument and pass it to
  blkdev_get().

Most of bdev open/close operations are unified into blkdev_get/put()
and most exclusive accesses are tested atomically at the open time (as
it should).  This cleans up code and removes some, both valid and
invalid, but unnecessary all the same, corner cases.

open_bdev_exclusive() and open_by_devnum() can use further cleanup -
rename to blkdev_get_by_path() and blkdev_get_by_devt() and drop
special features.  Well, let's leave them for another day.

Most conversions are straight-forward.  drbd conversion is a bit more
involved as there was some reordering, but the logic should stay the
same.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Brown <neilb@suse.de>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Alex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: dm-devel@redhat.com
Cc: drbd-dev@lists.linbit.com
Cc: Leo Chen <leochen@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Joern Engel <joern@logfs.org>
Cc: reiserfs-devel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
2010-11-13 11:55:17 +01:00
Kay Sievers 66d7dd518a /proc/swaps: support polling
System management wants to subscribe to changes in swap configuration.
Make /proc/swaps pollable like /proc/mounts.

[akpm@linux-foundation.org: document proc_poll_event]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg KH <greg@kroah.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-10-26 16:52:11 -07:00
Jens Axboe fa251f8990 Merge branch 'v2.6.36-rc8' into for-2.6.37/barrier
Conflicts:
	block/blk-core.c
	drivers/block/loop.c
	mm/swapfile.c

Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-10-19 09:13:04 +02:00
Christoph Hellwig dd3932eddf block: remove BLKDEV_IFL_WAIT
All the blkdev_issue_* helpers can only sanely be used for synchronous
caller.  To issue cache flushes or barriers asynchronously the caller needs
to set up a bio by itself with a completion callback to move the asynchronous
state machine ahead.  So drop the BLKDEV_IFL_WAIT flag that is always
specified when calling blkdev_issue_* and also remove the now unused flags
argument to blkdev_issue_flush and blkdev_issue_zeroout.  For
blkdev_issue_discard we need to keep it for the secure discard flag, which
gains a more descriptive name and loses the bitops vs flag confusion.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-09-16 20:52:58 +02:00
Christoph Hellwig 349f429eec swap: do not send discards as barriers
The swap code already uses synchronous discards, no need to add I/O barriers.

tj: superflous newlines removed.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hugh Dickins <hughd@google.com>
Tested-by: Nigel Cunningham <nigel@tuxonice.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-09-10 12:35:39 +02:00
Hugh Dickins 3399446632 swap: discard while swapping only if SWAP_FLAG_DISCARD
Tests with recent firmware on Intel X25-M 80GB and OCZ Vertex 60GB SSDs
show a shift since I last tested in December: in part because of firmware
updates, in part because of the necessary move from barriers to awaiting
completion at the block layer.  While discard at swapon still shows as
slightly beneficial on both, discarding 1MB swap cluster when allocating
is now disadvanteous: adds 25% overhead on Intel, adds 230% on OCZ (YMMV).

Surrender: discard as presently implemented is more hindrance than help
for swap; but might prove useful on other devices, or with improvements.
So continue to do the discard at swapon, but make discard while swapping
conditional on a SWAP_FLAG_DISCARD to sys_swapon() (which has been using
only the lower 16 bits of int flags).

We can add a --discard or -d to swapon(8), and a "discard" to swap in
/etc/fstab: matching the mount option for btrfs, ext4, fat, gfs2, nilfs2.

Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Nigel Cunningham <nigel@tuxonice.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-09-09 18:57:25 -07:00
Christoph Hellwig 8f2ae0faa3 swap: do not send discards as barriers
The swap code already uses synchronous discards, no need to add I/O
barriers.

This fixes the worst of the terrible slowdown in swap allocation for
hibernation, reported on 2.6.35 by Nigel Cunningham; but does not entirely
eliminate that regression.

[tj@kernel.org: superflous newlines removed]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Nigel Cunningham <nigel@tuxonice.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-09-09 18:57:25 -07:00
Hugh Dickins b73d7fcecd swap: prevent reuse during hibernation
Move the hibernation check from scan_swap_map() into try_to_free_swap():
to catch not only the common case when hibernation's allocation itself
triggers swap reuse, but also the less likely case when concurrent page
reclaim (shrink_page_list) might happen to try_to_free_swap from a page.

Hibernation already clears __GFP_IO from the gfp_allowed_mask, to stop
reclaim from going to swap: check that to prevent swap reuse too.

Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Ondrej Zary <linux@rainbow-software.org>
Cc: Andrea Gelmini <andrea.gelmini@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Nigel Cunningham <nigel@tuxonice.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-09-09 18:57:25 -07:00