Currently the for-loop will spin forever if variable supported is
non-zero because supported is never changed. Fix this by adding in
the missing right shift of supported.
Addresses-Coverity: ("Infinite loop")
Fixes: 48cb39522a ("mac80211: minstrel_ht: improve rate probing for devices with static fallback")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190822122034.28664-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On some devices that only support static rate fallback tables sending rate
control probing packets can be really expensive.
Probing lower rates can already hurt throughput quite a bit. What hurts even
more is the fact that on mt76x0/mt76x2, single probing packets can only be
forced by directing packets at a different internal hardware queue, which
causes some heavy reordering and extra latency.
The reordering issue is mainly problematic while pushing lots of packets to
a particular station. If there is little activity, the overhead of probing is
neglegible.
The static fallback behavior is designed to pretty much only handle rate
control algorithms that use only a very limited set of rates on which the
algorithm switches up/down based on packet error rate.
In order to better support that kind of hardware, this patch implements a
different approach to rate probing where it switches to a slightly higher rate,
waits for tx status feedback, then updates the stats and switches back to
the new max throughput rate. This only triggers above a packet rate of 100
per stats interval (~50ms).
For that kind of probing, the code has to reduce the set of probing rates
a lot more compared to single packet probing, so it uses only one packet
per MCS group which is either slightly faster, or as close as possible to
the max throughput rate.
This allows switching between similar rates with different numbers of
streams. The algorithm assumes that the hardware will work its way lower
within an MCS group in case of retransmissions, so that lower rates don't
have to be probed by the high packets per second rate probing code.
To further reduce the search space, it also does not probe rates with lower
channel bandwidth than the max throughput rate.
At the moment, these changes will only affect mt76x0/mt76x2.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On hardware with static fallback tables (e.g. mt76x2), rate probing attempts
can be very expensive.
On such devices, avoid sampling rates slower than the per-group max throughput
rate, based on the assumption that the fallback table will take care of probing
lower rates within that group if the higher rates fail.
To further reduce unnecessary probing attempts, skip duplicate attempts on
rates slower than the max throughput rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The group number needs to be multiplied by the number of rates per group
to get the full rate index
Fixes: 5935839ad7 ("mac80211: improve minstrel_ht rate sorting by throughput & probability")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
he_spr_ie_elem is dereferenced before the NULL check. fix this by moving
the assignment after the check.
fixes commit 697f6c507c ("mac80211: propagate HE operation info into
bss_conf")
This was reported by the static code checker.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190813070712.25509-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Report timestamp for when sta becomes associated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-2-greearb@candelatech.com
[fix ktime_get_boot_ns() to ktime_get_boottime_ns(), assoc_at type to u64]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the 802.11ax specification a new band is introduced, which
is also proposed by FCC for unlicensed use. This band is referred
to as 6GHz spanning frequency range from 5925 to 7125 MHz.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-2-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code generating the Tx Radiotap header when using tx_status_ext was
missing a field increment after setting the VHT bandwidth.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-4-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting 80MHz, we need to set 4 and not 2 inside the corresponding
field inside the Tx Radiotap header.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting legacy rates inside the TX Radiotap header we need to split
the check between "uses tx_statua_ext" and "is legacy rate". Not doing so
would make the code drop into the !tx_status_ext path.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RX Radiotap header length was not calculated properly when reporting
legacy rates using tx_status_ext.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of HE AP-STA link, ieee80211_send_nullfunc() will not
send the QOS NULL packet to check if AP is still associated.
In this case, probe_send_count will be non-zero and
ieee80211_sta_work() will later disassociate the AP, even
though no packet was ever sent.
Fix this by decrementing probe_send_count and not calling
ieee80211_send_nullfunc() in case of HE link, so that we
still wait for some time for the AP beacon to reappear and
don't disconnect right away.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20190703131848.22879-1-shay.bar@celeno.com
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Store the OBSS PD parameters inside bss_conf when bringing up an AP and/or
when a station connects to an AP. This allows the driver to configure the
HW accordingly.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190730163701.18836-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This came up in fuzz testing, and really we don't consider
all-zeroes to be a valid MAC address in most places, so
also reject it here to avoid confusion later on.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Link: https://lore.kernel.org/r/1563959770-21570-1-git-send-email-periyasa@codeaurora.org
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return from ieee80211_get_sband can potentially be a null pointer, so
it seems prudent to add a null check to avoid a null pointer dereference
on sband.
Addresses-Coverity: ("Dereference null return")
Fixes: 2ab4587675 ("mac80211: add support for the ADDBA extension element")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190730143205.14261-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert this for now, it has been reported multiple times that it
completely breaks connectivity on various devices.
Cc: stable@vger.kernel.org
Fixes: 8dbb000ee7 ("mac80211: set NETIF_F_LLTX when using intermediate tx queues")
Reported-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Peter Lebbing <peter@digitalbrains.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HE allows peers to negotiate the aggregation fragmentation level to be used
during transmission. The level can be 1-3. The Ext element is added behind
the ADDBA request inside the action frame. The responder will then reply
with the same level or a lower one if the requested one is not supported.
This patch only handles the negotiation part as the ADDBA frames get passed
to the ATH11k firmware, which does the rest of the magic for us aswell as
generating the requests.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190729104512.27615-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upon a successful assoc a station shall store the content of the HE
operation element inside bss_conf so that the driver can setup the
hardware accordingly.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190729102342.8659-2-john@phrozen.org
[use struct copy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a very similar spirit to commit c470bdc1aa ("mac80211: don't WARN
on bad WMM parameters from buggy APs"), an AP may not transmit a
fully-formed WMM IE. For example, it may miss or repeat an Access
Category. The above loop won't catch that and will instead leave one of
the four ACs zeroed out. This triggers the following warning in
drv_conf_tx()
wlan0: invalid CW_min/CW_max: 0/0
and it may leave one of the hardware queues unconfigured. If we detect
such a case, let's just print a warning and fall back to the defaults.
Tested with a hacked version of hostapd, intentionally corrupting the
IEs in hostapd_eid_wmm().
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190726224758.210953-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the basics required for supporting high efficiency with mesh:
include HE information elements in beacons, probe responses, and peering
action frames, and check for compatible HE configurations when peering.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Forwarded: https://patchwork.kernel.org/patch/11029299/
Link: https://lore.kernel.org/r/20190724163359.3507-2-sven@narfation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add IEEE80211_KEY_FLAG_GENERATE_MMIE flag to ieee80211_key_flags in order
to allow the driver to notify mac80211 to generate MMIE and that it
requires sequence number generation only.
This is a preliminary patch to add BIP_CMAC_128 hw support to mt7615
driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/dfe275f9aa0f1cc6b33085f9efd5d8447f68ad13.1563228405.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to mac80211 for parsing SPR elements as per
P802.11ax_D4.0 section 9.4.2.241.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190618061915.7102-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to ieee80211_add_tx_radiotap_header() for handling rates
reported via ieee80211_tx_status. This allows us to also report HE rates.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190714154419.11854-4-john@phrozen.org
[remove text about 60 GHz, mac80211 doesn't support it, fix endianness issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on
crypto controlled devices") has introduced a change which allows
4addr operation on crypto controlled devices (ex: ath10k). This
change has inadvertently impacted the interface combinations logic
on such devices.
General rule is that software interfaces like AP/VLAN should not be
listed under supported interface combinations and should not be
considered during validation of these combinations; because of the
aforementioned change, AP/VLAN interfaces(if present) will be checked
against interfaces supported by the device and blocks valid interface
combinations.
Consider a case where an AP and AP/VLAN are up and running; when a
second AP device is brought up on the same physical device, this AP
will be checked against the AP/VLAN interface (which will not be
part of supported interface combinations of the device) and blocks
second AP to come up.
Add a new API cfg80211_iftype_allowed() to fix the problem, this
API works for all devices with/without SW crypto control.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Fixes: 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on crypto controlled devices")
Link: https://lore.kernel.org/r/1563779690-9716-1-git-send-email-mpubbise@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extended Key ID allows A-MPDU sessions while rekeying as long as each
A-MPDU aggregates only MPDUs with one keyid together.
Drivers able to segregate MPDUs accordingly can tell mac80211 to not
stop A-MPDU sessions when rekeying by setting the new flag
IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190629195015.19680-3-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1) Drop IEEE80211_HW_EXT_KEY_ID_NATIVE and let drivers directly set
the NL80211_EXT_FEATURE_EXT_KEY_ID flag.
2) Drop IEEE80211_HW_NO_AMPDU_KEYBORDER_SUPPORT and simply assume all
drivers are unable to handle A-MPDU key borders.
The new Extended Key ID API now requires all mac80211 drivers to set
NL80211_EXT_FEATURE_EXT_KEY_ID when they implement set_key() and can
handle Extended Key ID. For drivers not providing set_key() mac80211
itself enables Extended Key ID support, using the internal SW crypto
services.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190629195015.19680-2-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since ieee80211_tx_dequeue() must not be called with softirqs enabled
(i.e. from process context without proper disable of bottom halves),
we add a wrapper that disables bottom halves before calling
ieee80211_tx_dequeue()
The new function is named ieee80211_tx_dequeue_ni() just as all other
from-process-context versions found in mac80211.
The documentation of ieee80211_tx_dequeue() is also updated so it
mentions that the function should not be called from process context.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Link: https://lore.kernel.org/r/20190617200140.6189-1-erik.stromdahl@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The remove_sta_debugfs callback in struct rate_control_ops is no longer
used by any driver, as there is no need for it (the debugfs directory is
already removed recursivly by the mac80211 core.) Because no one needs
it, just remove it to keep anyone else from accidentally using it in the
future.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190612142658.12792-5-gregkh@linuxfoundation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_set_wmm_default() normally sets up the initial CW min/max for
each queue, except that it skips doing this if the driver doesn't
support ->conf_tx. We still end up calling drv_conf_tx() in some cases
(e.g., ieee80211_reconfig()), which also still won't do anything
useful...except it complains here about the invalid CW parameters.
Let's just skip the WARN if we weren't going to do anything useful with
the parameters.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190718015712.197499-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
The WEP code in the mac80211 subsystem currently uses the crypto
API to access the arc4 (RC4) cipher, which is overly complicated,
and doesn't really have an upside in this particular case, since
ciphers are always synchronous and therefore always implemented in
software. Given that we have no accelerated software implementations
either, it is much more straightforward to invoke a generic library
interface directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Based on 1 normalized pattern(s):
gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 58 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.556988620@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
-----BEGIN PGP SIGNATURE-----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=j+Um
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Many changes all over:
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
-----BEGIN PGP SIGNATURE-----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=AHi5
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes, all over:
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the offchannel TX wait time expires, send the appropriate event.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is not a good idea to try to perform any work (e.g. send an auth
frame) during reconfigure flow.
Prevent this from happening, and at the end of the reconfigure flow
requeue all the works.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multiple SSID cases, it takes time to prepare every AP interface
to be ready in initializing phase. If a sta already knows everything it
needs to join one of the APs and sends authentication to the AP which
is not fully prepared at this point of time, AP's channel context
could be NULL. As a result, warning message occurs.
Even worse, if the AP is under attack via tools such as MDK3 and massive
authentication requests are received in a very short time, console will
be hung due to kernel warning messages.
WARN_ON_ONCE() could be a better way for indicating warning messages
without duplicate messages to flood the console.
Johannes: We still need to address the underlying problem, but we
don't really have a good handle on it yet. Suppress the
worst side-effects for now.
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
[johannes: add note, change subject]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving a robust management frame, drop it if we don't have
rx->sta since then we don't have a security association and thus
couldn't possibly validate the frame.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This appears to happen occasionally, and if it does we
really want even more information than we have now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If HW advertises it has rate control, we skip all of the
rate control assignments, but sometimes the data we have
here is useful, especially so that we don't have to do
the lookups again on which rates are configured and are
supported.
So do the low rate assignment anyway to help out drivers
that might need it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if we have a station, we currently call rate_control_send_low()
with the NULL station unless further rate control (driver, minstrel)
has been initialized.
Change this so we can use more information about the station to use
a better rate. For example, when we associate with an AP, we will
now use the lowest rate it advertised as supported (that we can)
rather than the lowest mandatory rate. This aligns our behaviour
with most other 802.11 implementations.
To make this possible, we need to also ensure that we have non-zero
rates at all times, so in case we really have *nothing* pre-fill
the supp_rates bitmap with the very lowest mandatory bitmap (11b
and 11a on 2.4 and 5 GHz respectively).
Additionally, hostapd appears to be giving us an empty supported
rates bitmap (it can and should do better, since the STA must have
supported for at least the basic rates in the BSS), so ignore any
such bitmaps that would actually zero out the supp_rates, and in
that case just keep the pre-filled mandatory rates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the userland daemon to en/disable TWT support for an AP.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
[simplify parsing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Turn TWT for STA interfaces when they associate and/or receive a
beacon where the twt_responder bit has changed.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE 802.11 - 2016 forbids mixing MPDUs with different keyIDs in one
A-MPDU. Drivers supporting A-MPDUs and Extended Key ID must actively
enforce that requirement due to the available two unicast keyIDs.
Allow driver to signal mac80211 that they will not check the keyID in
MPDUs when aggregating them and that they expect mac80211 to stop Tx
aggregation when rekeying a connection using Extended Key ID.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on 1 normalized pattern(s):
this file is gplv2 as found in copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.657082701@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ifa_list is protected by rcu, yet code doesn't reflect this.
Add the __rcu annotations and fix up all places that are now reported by
sparse.
I've done this in the same commit to not add intermediate patches that
result in new warnings.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
freeing peer keys after vif down is resulting in peer key uninstall
to fail due to interface lookup failure. so fix that.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ifmsh->csa is an RCU-protected pointer. The writer context
in ieee80211_mesh_finish_csa() is already mutually
exclusive with wdev->sdata.mtx, but the RCU checker did
not know this. Use rcu_dereference_protected() to avoid a
warning.
fixes the following warning:
[ 12.519089] =============================
[ 12.520042] WARNING: suspicious RCU usage
[ 12.520652] 5.1.0-rc7-wt+ #16 Tainted: G W
[ 12.521409] -----------------------------
[ 12.521972] net/mac80211/mesh.c:1223 suspicious rcu_dereference_check() usage!
[ 12.522928] other info that might help us debug this:
[ 12.523984] rcu_scheduler_active = 2, debug_locks = 1
[ 12.524855] 5 locks held by kworker/u8:2/152:
[ 12.525438] #0: 00000000057be08c ((wq_completion)phy0){+.+.}, at: process_one_work+0x1a2/0x620
[ 12.526607] #1: 0000000059c6b07a ((work_completion)(&sdata->csa_finalize_work)){+.+.}, at: process_one_work+0x1a2/0x620
[ 12.528001] #2: 00000000f184ba7d (&wdev->mtx){+.+.}, at: ieee80211_csa_finalize_work+0x2f/0x90
[ 12.529116] #3: 00000000831a1f54 (&local->mtx){+.+.}, at: ieee80211_csa_finalize_work+0x47/0x90
[ 12.530233] #4: 00000000fd06f988 (&local->chanctx_mtx){+.+.}, at: ieee80211_csa_finalize_work+0x51/0x90
Signed-off-by: Thomas Pedersen <thomas@eero.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_aes_gmac() uses the mic argument directly in sg_set_buf() and
that does not allow use of stack memory (e.g., BUG_ON() is hit in
sg_set_buf() with CONFIG_DEBUG_SG). BIP GMAC TX side is fine for this
since it can use the skb data buffer, but the RX side was using a stack
variable for deriving the local MIC value to compare against the
received one.
Fix this by allocating heap memory for the mic buffer.
This was found with hwsim test case ap_cipher_bip_gmac_128 hitting that
BUG_ON() and kernel panic.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per the current design, in the case of sw crypto controlled devices,
it is the device which advertises the support for AP/VLAN iftype based
on it's ability to tranmsit packets encrypted in software
(In VLAN functionality, group traffic generated for a specific
VLAN group is always encrypted in software). Commit db3bdcb9c3
("mac80211: allow AP_VLAN operation on crypto controlled devices")
has introduced this change.
Since 4addr AP operation also uses AP/VLAN iftype, this conditional
way of advertising AP/VLAN support has broken 4addr AP mode operation on
crypto controlled devices which do not support VLAN functionality.
In the case of ath10k driver, not all firmwares have support for VLAN
functionality but all can support 4addr AP operation. Because AP/VLAN
support is not advertised for these devices, 4addr AP operations are
also blocked.
Fix this by allowing 4addr operation on devices which do not support
AP/VLAN iftype but can support 4addr AP operation (decision is based on
the wiphy flag WIPHY_FLAG_4ADDR_AP).
Cc: stable@vger.kernel.org
Fixes: db3bdcb9c3 ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
net/mac80211/key.c: In function 'ieee80211_set_tx_key':
net/mac80211/key.c:271:24: warning:
variable 'old' set but not used [-Wunused-but-set-variable]
It is not used since introduction in
commit 96fc6efb9a ("mac80211: IEEE 802.11 Extended Key ID support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving a deauthentication/disassociation frame from a TDLS
peer, a station should not disconnect the current AP, but only
disable the current TDLS link if it's enabled.
Without this change, a TDLS issue can be reproduced by following the
steps as below:
1. STA-1 and STA-2 are connected to AP, bidirection traffic is running
between STA-1 and STA-2.
2. Set up TDLS link between STA-1 and STA-2, stay for a while, then
teardown TDLS link.
3. Repeat step #2 and monitor the connection between STA and AP.
During the test, one STA may send a deauthentication/disassociation
frame to another, after TDLS teardown, with reason code 6/7, which
means: Class 2/3 frame received from nonassociated STA.
On receive this frame, the receiver STA will disconnect the current
AP and then reconnect. It's not a expected behavior, purpose of this
frame should be disabling the TDLS link, not the link with AP.
Cc: stable@vger.kernel.org
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
-----BEGIN PGP SIGNATURE-----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=JQOx
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The requirement for mesh link metric refreshing, is that from one
mesh point we be able to send some data frames to other mesh points
which are not currently selected as a primary traffic path, but which
are only 1 hop away. The absence of the primary path to the chosen node
makes it necessary to apply some form of marking on a chosen packet
stream so that the packets can be properly steered to the selected node
for testing, and not by the regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allows setting of control flags of skb cb - if needed -
when calling ieee80211_subif_start_xmit().
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mac80211 SW crypto handles replacing PTK keys correctly.
Don't trigger needless warnings or workarounds when the driver can only
use the known good SW crypto provided by mac80211.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Only enable Extended Key ID support for drivers which are not supporting
crypto offload and also do not support A-MPDU.
While any driver using SW crypto from mac80211 is generally able to also
support Extended Key ID these drivers are likely to mix keyIDs in
AMPDUs when rekeying.
According to IEEE 802.11-2016 "9.7.3 A-MPDU contents" this is not
allowed.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[reword comment a bit, move ! into logic expression]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cfg80211_merge_profile() and ieee802_11_find_bssid_profile() are
a bit cleaner if we just pass the merged_ie pointer instead of a pointer
to the pointer.
This isn't a functional change, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch introduce a new driver callback drv_sta_set_txpwr. This API will
copy the transmit power value passed from user space and call the driver
callback to set the tx power for the station.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to allocate than one queue in the iTXQs case
now that we no longer use ndo_select_queue to assign the AC.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At Technical University of Munich we use MAC 802.11 TX status frames to
perform several measurements in MAC 802.11 setups.
With ath based drivers this was possible until commit d94a461d7a
("ath9k: use ieee80211_tx_status_noskb where possible") as the driver
ignored the IEEE80211_TX_CTL_REQ_TX_STATUS flag and always delivered
tx_status frames. Since that commit, this behavior was changed and the
driver now adheres to IEEE80211_TX_CTL_REQ_TX_STATUS.
Due to performance reasons, IEEE80211_TX_CTL_REQ_TX_STATUS is not set for
data frames from interfaces in managed mode. Hence, frames that are sent
from a managed mode interface do never deliver tx_status frames. This
remains true even if a monitor mode interface (the measurement interface)
is added to the same ieee80211 physical device. Thus, there is no
possibility for receiving tx_status frames for frames sent on an interface
in managed mode, if the driver adheres to IEEE80211_TX_CTL_REQ_TX_STATUS.
In order to force delivery of tx_status frames for research and debugging
purposes, implement a debugfs option force_tx_status for ieee80211 physical
devices. When this option is set for a physical device,
IEEE80211_TX_CTL_REQ_TX_STATUS is enabled in all packets sent from that
device. This option can be set via
/sys/kernel/debug/ieee80211/<dev>/force_tx_status. The default is disabled.
Co-developed-by: Charlie Groh <ga58taw@mytum.de>
Signed-off-by: Charlie Groh <ga58taw@mytum.de>
Signed-off-by: Julius Niedworok <julius.n@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FullMAC STAs have no way to update bss channel after CSA channel switch
completion. As a result, user-space tools may provide inconsistent
channel info. For instance, consider the following two commands:
$ sudo iw dev wlan0 link
$ sudo iw dev wlan0 info
The latter command gets channel info from the hardware, so most probably
its output will be correct. However the former command gets channel info
from scan cache, so its output will contain outdated channel info.
In fact, current bss channel info will not be updated until the
next [re-]connect.
Note that mac80211 STAs have a workaround for this, but it requires
access to internal cfg80211 data, see ieee80211_chswitch_work:
/* XXX: shouldn't really modify cfg80211-owned data! */
ifmgd->associated->channel = sdata->csa_chandef.chan;
This patch suggests to convert mac80211 workaround into cfg80211 behavior
and to update current bss channel in cfg80211_ch_switch_notify.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A per-group shift was added to reduce the size of the per-rate transmit
duration field to u16 without sacrificing a lot of precision
This patch changes the macros to automatically calculate the best value for
this shift based on the lowest rate within the group.
This simplifies adding more groups and slightly improves accuracy for some of
the existing groups.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is needed for the upcoming driver for MT7615 4x4 802.11ac chipsets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using iTXQ, the network stack does not need the real queue number, since
mac80211 is using its internal queues anyway. In that case we can defer
selecting the queue and remove a redundant station lookup in the tx path to save
some CPU cycles.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for Extended Key ID as defined in IEEE 802.11-2016.
- Implement the nl80211 API for Extended Key ID
- Extend mac80211 API to allow drivers to support Extended Key ID
- Enable Extended Key ID by default for drivers only supporting SW
crypto (e.g. mac80211_hwsim)
- Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX)
- Select the decryption key based on the MPDU keyid
- Enforce existing assumptions in the code that rekeys don't change the
cipher
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[remove module parameter]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Optimize/cleanup the delay tailroom checks and adds one missing tailroom
update.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using iTXQ, tx sequence number allocation and statistics are run at
dequeue time. Because of that, it is safe to enable NETIF_F_LLTX, which
allows tx handlers to run on multiple CPUs in parallel.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reduces lock contention on enqueue/dequeue of iTXQ packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reduces lock contention on enqueue/dequeue of iTXQ packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The callers of these functions are all within RCU locked sections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since an element is limited to 255 octets, a profile may be split
split to several elements. Support the split as defined in the 11ax
draft 3.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Subelement profile may specify element IDs it doesn't inherit
from the management frame. Support it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to dereference the directory to get its parent to
be able to rename it, so it's clearly not safe to try to
do this with ERR_PTR() pointers. Skip in this case.
It seems that this is most likely what was causing the
report by syzbot, but I'm not entirely sure as it didn't
come with a reproducer this time.
Cc: stable@vger.kernel.org
Reported-by: syzbot+4ece1a28b8f4730547c9@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The txq of vif is added to active_txqs list for ATF TXQ scheduling
in the function ieee80211_queue_skb(), but it was not properly removed
before freeing the txq object. It was causing use after free of the txq
objects from the active_txqs list, result was kernel panic
due to invalid memory access.
Fix kernel invalid memory access by properly removing txq object
from active_txqs list before free the object.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The original patch neglected to take byte order conversions
into account, fix that.
Fixes: d9bb410888 ("mac80211: allow overriding HT STBC capabilities")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Restore SW_CRYPTO_CONTROL operation on AP_VLAN interfaces for unicast
keys, the original override was intended to be done for group keys as
those are treated specially by mac80211 and would always have been
rejected.
Now the situation is that AP_VLAN support must be enabled by the driver
if it can support it (meaning it can support software crypto GTK TX).
Thus, also simplify the code - if we get here with AP_VLAN and non-
pairwise key, software crypto must be used (driver doesn't know about
the interface) and can be used (driver must've advertised AP_VLAN if
it also uses SW_CRYPTO_CONTROL).
Fixes: db3bdcb9c3 ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for mesh airtime link metric attribute
NL80211_STA_INFO_AIRTIME_LINK_METRIC.
Signed-off-by: Narayanraddi Masti <team.nmasti@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Holding the lock around the entire duration of tx scheduling can create
some nasty lock contention, especially when processing airtime information
from the tx status or the rx path.
Improve locking by only holding the active_txq_lock for lookups / scheduling
list modifications.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are several scenarios in which mac80211 can call drv_wake_tx_queue
after ieee80211_restart_hw has been called and has not yet completed.
Driver private structs are considered uninitialized until mac80211 has
uploaded the vifs, stations and keys again, so using private tx queue
data during that time is not safe.
The driver can also not rely on drv_reconfig_complete to figure out when
it is safe to accept drv_wake_tx_queue calls again, because it is only
called after all tx queues are woken again.
To fix this, bail out early in drv_wake_tx_queue if local->in_reconfig
is set.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
skb->truesize can change due to memory reallocation or when adding extra
fragments. Adjust fq->memory_usage accordingly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Looks that 100 chars isn't enough for messages, as we keep getting
warnings popping from different places due to message shortening.
Instead of trying to shorten the prints, just increase the buffer size.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pointer to the last four bytes of the address is not guaranteed to be
aligned, so we need to use __get_unaligned_cpu32 here
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Once a station enters powersave, its queues should not be returned by
ieee80211_next_txq() anymore. They will be re-scheduled again after the
station has woken up again
Fixes: 1866760096 ("mac80211: Add TXQ scheduling API")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
Forwarded packets enter the tx path through ieee80211_add_pending_skb,
which skips the ieee80211_skb_resize call.
Fixes WARN_ON in ccmp_encrypt_skb and resulting packet loss.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code in mesh_path_add tries to handle the case where a duplicate
entry is added to the rhashtable by doing a lookup after a failed
insertion. It also tries to handle races by repeating the insertion
should the lookup fail.
This is now unnecessary as we have rhashtable API functions that can
directly return the mathcing object.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next to resolve a conflict and to get the mac80211
rhashtable fixes so further patches can be applied on top.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update element names and new fields according to D3.3 of
the HE spec.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some buggy APs keep the CSA IE in probes after the channel
switch was completed and can silence us for no good reason.
Apply quiet mode only from beacons. If there is real channel
switch going on, we will see the beacon anyway.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, due to some buggy APs that continue to include
CSA IEs after the switch, we ignore CSA to same channel.
However, some other APs may do CSA to self in order to have
immediate quiet. Allow it. Do it only for beacons.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to track further the CSA beacons, for example
to compensate for buggy APs that change the beacon count or quiet
mode during CSA flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_vendor_radiotap was read from the beginning
of the skb->data regardless of the existence of other
elements in radiotap that would cause it to move to another
position. Fix this by taking into account where it really
should be.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we receive a beacon without CSA IE while we are in
the middle of channel switch - abort the operation.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018 REVmd of the spec introduces the max channel switch time
element which is optionally included in beacons/probes when there
is a channel switch / extended channel switch element.
The value represents the maximum delay between the time the AP
transmitted the last beacon in current channel and the expected
time of the first beacon in the new channel, in TU.
Parse the value and pass it to the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends the NL80211_CMD_ASSOCIATE event case to report
NL80211_ATTR_REQ_IE similarly to what is already done with the
NL80211_CMD_CONNECT events if the driver provides this information. In
practice, this adds (Re)Association Request frame information element
reporting to mac80211 drivers for the cases where user space SME is
used.
This provides more information for user space to figure out which
capabilities were negotiated for the association. For example, this can
be used to determine whether HT, VHT, or HE is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we did the original tests for the optimal value of sk_pacing_shift, we
came up with 6 ms of buffering as the default. Sadly, 6 is not a power of
two, so when picking the shift value I erred on the size of less buffering
and picked 4 ms instead of 8. This was probably wrong; those 2 ms of extra
buffering makes a larger difference than I thought.
So, change the default pacing shift to 7, which corresponds to 8 ms of
buffering. The point of diminishing returns really kicks in after 8 ms, and
so having this as a default should cut down on the need for extensive
per-device testing and overrides needed in the drivers.
Cc: stable@vger.kernel.org
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
spin_lock_bh() is used in table_path_del() but rcu_read_unlock()
is used for unlocking. Fix it by using spin_unlock_bh() instead
of rcu_read_unlock() in the error handling case.
Fixes: b4c3fbe636 ("mac80211: Use linked list instead of rhashtable walk for mesh tables")
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
The starting of AP interface can fail due to invalid
beacon interval, which does not match the minimum gcd
requirement set by the wifi driver. In such case, the
beacon interval of that interface gets updated with
that invalid beacon interval.
The next time that interface is brought up in AP mode,
an interface combination check is performed and the
beacon interval is taken from the previously set value.
In a case where an invalid beacon interval, i.e. a beacon
interval value which does not satisfy the minimum gcd criteria
set by the driver, is set, all the subsequent trials to
bring that interface in AP mode will fail, even if the
subsequent trials have a valid beacon interval.
To avoid this, in case of a failure in bringing up an
interface in AP mode due to interface combination error,
the interface beacon interval which is stored in bss
conf, needs to be restored with the last working value
of beacon interval.
Tested on ath10k using WCN3990.
Cc: stable@vger.kernel.org
Fixes: 0c317a02ca ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When rhashtable insertion fails the mesh table code doesn't free
the now-orphan mesh path object. This patch fixes that.
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh table code walks over hash tables for two purposes. First of
all it's used as part of a netlink dump process, but it is also used
for looking up entries to delete using criteria other than the hash
key.
The second purpose is directly contrary to the design specification
of rhashtable walks. It is only meant for use by netlink dumps.
This is because rhashtable is resizable and you cannot obtain a
stable walk over it during a resize process.
In fact mesh's use of rhashtable for dumping is bogus too. Rather
than using rhashtable walk's iterator to keep track of the current
position, it always converts the current position to an integer
which defeats the purpose of the iterator.
Therefore this patch converts all uses of rhashtable walk into a
simple linked list.
This patch also adds a new spin lock to protect the hash table
insertion/removal as well as the walk list modifications. In fact
the previous code was buggy as the removals can race with each
other, potentially resulting in a double-free.
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 requests the low level driver to stop an ongoing
Tx aggregation, the low level driver is expected to call
ieee80211_stop_tx_ba_cb_irqsafe() to indicate that it is ready
to stop the session. The callback in turn schedules a worker
to complete the session tear down, which in turn also handles
the relevant state for the intermediate Tx queue.
However, as this flow in asynchronous, the intermediate queue
should be stopped and not continue servicing frames, as in
such a case frames that are dequeued would be marked as part
of an aggregation, although the aggregation is already been
stopped.
Fix this by stopping the intermediate Tx queue, before
calling the low level driver to stop the Tx aggregation.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a driver does any significant activity in its ibss_join method,
then it will very well expect that to be called during restart,
before any stations are added. Do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Set multi-bssid support flags according to driver support.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for multi-bssid.
This includes:
- Parsing multi-bssid element
- Overriding DTIM values
- Taking into account in various places the inner BSSID instead of
transmitter BSSID
- Save aside some multi-bssid properties needed by drivers
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow iterating over multiple BSSs inside
cfg80211_bss, in case of multiple BSSID.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multiple BSSID, we have nested IEs inside the multiple
BSSID IE, that override the external ones for that specific
BSS. As preparation for supporting that, pass 2 BSSIDs to the
parse function, the transmitter, and the selected BSSID, so
it can know which IEs to choose. If the selected BSSID is
NULL, the outer ones will be applied.
Change ieee80211_bss_info_update to parse elements itself,
instead of receiving them parsed, so we have the relevant
bss entry in hand.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the missing and malformed documentation that kernel-doc and
sphinx warn about. While at it, also add some things to the docs
to fix missing links.
Sadly, the only way I could find to fix this was to add some
trailing whitespace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers use IEEE80211_KEY_FLAG_SW_MGMT_TX to indicate that management
frames need to be software encrypted. Since normal data packets are still
encrypted by the hardware, crypto_tx_tailroom_needed_cnt gets decremented
after key upload to hw. This can lead to passing skbs to ccmp_encrypt_skb,
which don't have the necessary tailroom for software encryption.
Change the code to add tailroom for encrypted management packets, even if
crypto_tx_tailroom_needed_cnt is 0.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next so that we get the changes from net, which would
otherwise conflict with the NLA_POLICY_NESTED/_ARRAY changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was a typo in the documentation for weight_multiplier in mac80211.h,
and the doc was missing entirely for airtime and airtime_weight in sta_info.h.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clearly, I missed this when trying out the previously
merged patches. Remove the spurious variable now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we reworked ieee80211_return_txq() so it assumes that the caller
takes care of logging, we need another function that can be called without
holding any locks. Introduce ieee80211_schedule_txq() which serves this
purpose.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During refactor in commit 9e478066ea ("mac80211: fix MU-MIMO
follow-MAC mode") a new struct 'action' was declared with packed
attribute as:
struct {
struct ieee80211_hdr_3addr hdr;
u8 category;
u8 action_code;
} __packed action;
But since struct 'ieee80211_hdr_3addr' is declared with an aligned
keyword as:
struct ieee80211_hdr {
__le16 frame_control;
__le16 duration_id;
u8 addr1[ETH_ALEN];
u8 addr2[ETH_ALEN];
u8 addr3[ETH_ALEN];
__le16 seq_ctrl;
u8 addr4[ETH_ALEN];
} __packed __aligned(2);
Solve the ambiguity of placing aligned structure in a packed one by
adding the aligned(2) attribute to struct 'action'.
This removes the following warning (W=1):
net/mac80211/rx.c:234:2: warning: alignment 1 of 'struct <anonymous>' is less than 2 [-Wpacked-not-aligned]
Cc: Johannes Berg <johannes.berg@intel.com>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardware (e.g. MediaTek MT7603) cannot report A-MPDU length in tx status
information. Add support for a flag to indicate that, to allow minstrel_ht
to use a fixed value in its internal calculation (which gives better results
than just defaulting to 1).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This helps to reduce frequent path switches when multiple path
candidates have the same or very similar path metrics.
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use bitrate moving average to smooth out link metric and stablize path
selection.
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose path change count to destination in mpath info
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose hop count to destination information in mpath info
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow user to override STBC configuration for Rx and Tx spatial streams.
In practice RX/TX STBC settings can be modified using appropriate
options in wpa_supplicant configuration file:
tx_stbc=-1..1
rx_stbc=-1..3
This functionality has been added to wpa_supplicant in commit cdeea70f59d0.
In FullMAC case these STBC options are passed to drivers by cfg80211
connect callback in fields of cfg80211_connect_params structure.
However for mac80211 drivers, e.g. for mac80211_hwsim,
overrides for STBC settings are ignored.
The reason why RX/TX STBC capabilities are not modified for mac80211
drivers is as follows. All drivers need to specify supported HT/VHT
overrides explicitly: see ht_capa_mod_mask and vht_capa_mod_mask fields
of wiphy structure. Only supported overrides will be passed to drivers by
cfg80211_connect and cfg80211_mlme_assoc operations: see bitwise 'AND'
performed by cfg80211_oper_and_ht_capa and cfg80211_oper_and_vht_capa.
This commit adds RX/TX STBC HT capabilities to mac80211_ht_capa_mod_mask,
allowing their modifications, as well as applies requested STBC
modifications in function ieee80211_apply_htcap_overrides.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds airtime accounting and scheduling to the mac80211 TXQ
scheduler. A new callback, ieee80211_sta_register_airtime(), is added
that drivers can call to report airtime usage for stations.
When airtime information is present, mac80211 will schedule TXQs
(through ieee80211_next_txq()) in a way that enforces airtime fairness
between active stations. This scheduling works the same way as the ath9k
in-driver airtime fairness scheduling. If no airtime usage is reported
by the driver, the scheduler will default to round-robin scheduling.
For drivers that don't control TXQ scheduling in software, a new API
function, ieee80211_txq_may_transmit(), is added which the driver can use
to check if the TXQ is eligible for transmission, or should be throttled to
enforce fairness. Calls to this function must also be enclosed in
ieee80211_txq_schedule_{start,end}() calls to ensure proper locking.
The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
aligned aginst driver's own round-robin scheduler list. i.e it rotates
the TXQ list till it makes the requested node becomes the first entry
in TXQ list. Thus both the TXQ list and driver's list are in sync.
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Louie Lu <git@louie.lu>
[added debugfs write op to reset airtime counter]
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds an API to mac80211 to handle scheduling of TXQs. The interface
between driver and mac80211 for TXQ handling is changed by adding two new
functions: ieee80211_next_txq(), which will return the next TXQ to schedule
in the current round-robin rotation, and ieee80211_return_txq(), which the
driver uses to indicate that it has finished scheduling a TXQ (which will
then be put back in the scheduling rotation if it isn't empty).
The driver must call ieee80211_txq_schedule_start() at the start of each
scheduling session, and ieee80211_txq_schedule_end() at the end. The API
then guarantees that the same TXQ is not returned twice in the same
session (so a driver can loop on ieee80211_next_txq() without worrying
about breaking the loop.
Usage of the new API is optional, so drivers can be ported one at a time.
In this patch, the actual scheduling performed by mac80211 is simple
round-robin, but a subsequent commit adds airtime fairness awareness to the
scheduler.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[minor kernel-doc fix, propagate sparse locking checks out]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_rx_h_mesh_fwding, we increment the 'dropped_frames_ttl'
counter when we decrement the ttl to zero. For unicast frames
destined for other hosts, we stop processing the frame at that point.
For multicast frames, we do not rebroadcast it in this case, but we
do pass the frame up the stack to process it on this STA. That
doesn't match the usual definition of "dropped," so don't count
those as such.
With this change, something like `ping6 -i0.2 ff02::1%mesh0` from a
peer in a ttl=1 network no longer increments the counter rapidly.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAlwaCwkACgkQB8qZga/f
l8S7mA/+I1CJmGC7Pvy+SBFkzoY5zEjjzgZYL6sGo16qMs89NPcURSe5j+uCsDP3
nKEjsvhQMYDfGNLTJJfWbDpGwm9LnKp69AFITlvfzmP6Sm36QMZr7oIC4abi8cW4
osaO3qfdaNoZ//x72jgjrFhUAnphvT2BsRVMNEjz7sXcDd7Jm9NnpRhV8zgXFvLF
dS2Ng51LM/BLMz5jQpyJUDZeeL/iBYybCecyckmVqzXPh1icIZETSqZXiN4ngv2A
6p9BSGNtP6wmjnbkvZz5RDq76VhTPZWsTgTpVb45Wf1k2fm1rB96UgpqvfQtjTgB
+7Zx2WRpMXM5OjGkwaEs8nawFmt7MHCGnhLPLWPCbXc685fhp3OFShysMJdYS/GZ
IIRJ7+IchAQX1yluftB+NkQM9sBDjyseMBwxHRYkj/rQVhoLY1sT+ke7lkuV10o6
DQqfpUTZAsIz7zkuscn7hkNdI/Rjub6BZjbrs1Jt9zSt9WQUBao23XudOI0j5JDa
ErnfC5PISXMQWik5B9M1Zhq3H9qCI2Swh19lMmtxtSDQ9yrLrJkEJ5SA+aHoxNHj
wSxBc3XXSW47qPXGX/D5DNnbOcOrE7kVZuD8YqRsy8VedyjIgEw7oQ21flAD4FC4
R4TgbNkqpfZQsU29gaMkDkYXnfQDB/G9FOk6ARGxjBPjT55Hz0E=
=EpyK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The radiotap vendor data might be placed after some other
radiotap elements, and thus when accessing it, need to access
the correct offset in the skb data. Fix the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 uses the frag list to build AMSDU. When freeing
the skb, it may not be really freed, since someone is still
holding a reference to it.
In that case, when TCP skb is being retransmitted, the
pointer to the frag list is being reused, while the data
in there is no longer valid.
Since we will never get frag list from the network stack,
as mac80211 doesn't advertise the capability, we can safely
free and nullify it before releasing the SKB.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the alignment handling, it actually matters where in the code
we add the 4 bytes for the presence bitmap to the length; the first
field is the timestamp with 8 byte alignment so we need to add the
space for the extra vendor namespace presence bitmap *before* we do
any alignment for the fields.
Move the presence bitmap length accounting to the right place to fix
the alignment for the data properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When disabling HE due to the lack of HT/VHT, do it
at an earlier stage to avoid advertising HE capabilities IE.
Also, at this point, no need to check if AP supports HE, since
it is already checked earlier (in ieee80211_prep_channel).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Up until now, the IEEE80211_STA_DISABLE_HE flag was set only based
on whether the AP has advertised HE capabilities.
This flag should be set also if STA does not support HE
(regardless of the AP support).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to WMM IE, if MU_EDCA IE parameters changed (or ceased to exist)
tell the Driver about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TWT is a feature that was added in 11ah and enhanced in
11ax. There are two bits that need to be set if we want
to use the feature in 11ax: one in the HE Capability IE
and one in the Extended Capability IE. This is because
of backward compatibility between 11ah and 11ax.
In order to simplify the flow for the low level driver
in managed mode, aggregate the two bits and add a boolean
that tells whether TWT is supported or not, but only if
11ax is supported.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we build AMSDU from GSO packets, it can lead to
bad results if anyone tries to call skb_gso_segment
on the packets.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the place where this code lives now, the skb can never be
NULL, so we can remove the pointless NULL check.
It seems to exist because this code was moved around a few times
and originally came from a place where it could in fact be NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This isn't really a problem now, but it means that the function
has a few NULL checks that are only relevant when coming from
the initial interface added in mac80211, and that's confusing.
Just pass non-NULL (but equivalently empty) in that case and
remove all the NULL checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The monitor interface Rx handling of SKBs that contain only
radiotap information was buggy as it tried to access the
SKB assuming it contains a frame.
To fix this, check the RX_FLAG_NO_PSDU flag in the Rx status
(indicting that the SKB contains only radiotap information),
and do not perform data path specific processing when the flag
is set.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pointer and corresponding length is always set in pairs
in cfg80211, so no need to have this strange defensive check
that also confuses static checkers. Clean it up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently TXQ teardown was moved earlier in ieee80211_unregister_hw(),
to avoid a use-after-free of the netdev data. However, interfaces
aren't fully removed at the point, and cfg80211_shutdown_all_interfaces
can for example, TX a deauth frame. Move the TXQ teardown to the
point between cfg80211_shutdown_all_interfaces and the free of
netdev queues, so we can be sure they are torn down before netdev
is freed, but after there is no ongoing TX.
Fixes: 77cfaf52ec ("mac80211: Run TXQ teardown code before de-registering interfaces")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iTXQs stop/wake queue mechanism involves a whole bunch
of locks and this is probably why the call to
ieee80211_wake_txqs is deferred to a tasklet when called from
__ieee80211_wake_queue.
Another advantage of that is that ieee80211_wake_txqs might
call the wake_tx_queue() callback and then the driver may
call mac80211 which will call it back in the same context.
The bug I saw is that when we send a deauth frame as a
station we do:
flush(drop=1)
tx deauth
flush(drop=0)
While we flush we stop the queues and wake them up
immediately after we finished flushing. The problem here is
that the tasklet that de-facto enables the queue may not have
run until we send the deauth. Then the deauth frame is sent
to the driver (which is surprising by itself), but the driver
won't get anything useful from ieee80211_tx_dequeue because
the queue is stopped (or more precisely because
vif->txqs_stopped[0] is true).
Then the deauth is not sent. Later on, the tasklet will run,
but that'll be too late. We'll already have removed all the
vif etc...
Fix this by calling ieee80211_wake_txqs synchronously if we
are not waking up the queues from the driver (we check the
reason to determine that). This makes the code really
convoluted because we may call ieee80211_wake_txqs from
__ieee80211_wake_queue. The latter assumes that
queue_stop_reason_lock has been taken by the caller and
ieee80211_wake_txqs may release the lock to send the frames.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lubomir Rintel recently pointed out a dead link for o11s.org, and
repointed it to a still live, but also stale website. As far as I
know, no one is updating the content at open80211s.org.
Since this Kconfig text was originally written, though, the 802.11s
mesh drafts were approved and ultimately rolled into 802.11 proper.
Meanwhile, the implementation has converged on the final standard,
so we can lose all of the text here and provide something that's a
little more helpful and accurate.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NullFunc packets should never be duplicate just like
QoS-NullFunc packets.
We saw a client that enters / exits power save with
NullFunc frames (and not with QoS-NullFunc) despite the
fact that the association supports HT.
This specific client also re-uses a non-zero sequence number
for different NullFunc frames.
At some point, the client had to send a retransmission of
the NullFunc frame and we dropped it, leading to a
misalignment in the power save state.
Fix this by never consider a NullFunc frame as duplicate,
just like we do for QoS NullFunc frames.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201449
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the buffered broadcast queue contains packets, letting new packets bypass
that queue can lead to heavy reordering, since the driver is probably throttling
transmission of buffered multicast packets after beacons.
Keep buffering packets until the buffer has been cleared (and no client
is in powersave mode).
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it behave like regular ieee80211_tx_status calls, except for the lack of
filtered frame processing.
This fixes spurious low-ack triggered disconnections with powersave clients
connected to an AP.
Fixes: f027c2aca0 ("mac80211: add ieee80211_tx_status_noskb")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
'cipher' algorithms (single block ciphers) are always synchronous, so
passing CRYPTO_ALG_ASYNC in the mask to crypto_alloc_cipher() has no
effect. Many users therefore already don't pass it, but some still do.
This inconsistency can cause confusion, especially since the way the
'mask' argument works is somewhat counterintuitive.
Thus, just remove the unneeded CRYPTO_ALG_ASYNC flags.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When peering is in userspace, some implementations may want to control
which peers are accepted based on RSSI in addition to the information
elements being sent today. Add signal level so that info is available
to clients.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When userspace is controlling mesh routing, it may have better
knowledge about whether a mesh STA is connected to a mesh
gate than the kernel mpath table. Add dot11MeshConnectedToMeshGate
to the mesh config so that such applications can explicitly
signal that a mesh STA is connected to a gate, which will then
be advertised in the beacon.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Capture the current state of gate connectivity from the mesh
formation field in mesh config whenever we receive a beacon,
and report that via GET_STATION. This allows applications
doing mesh peering in userspace to make peering decisions
based on peers' current upstream connectivity.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Connected to Mesh Gate subfield (802.11-2016 9.4.2.98.7) in the Mesh
Formation Info field is currently unset. This field may be useful in
determining which MBSSes to join or which mesh STAs to peer with.
If this mesh STA is a gate, by having turned on mesh gate announcements,
or if we have a path to one (e.g. by having received RANNs) then set this
bit to 1.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, like in the rsi driver hardware scan offload, there
may be scenarios in which hardware scan might not be available or
desirable.
Allow drivers to cope with this by letting them fall back to software
scan by returning the special value 1 from the hardware scan method.
Requested-by: Sushant Kumar Mishra <sushant2k1513@gmail.com>
Requested-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's nothing much for mac80211 to do, so only pass through
the requests with minimal checks and tracing. The driver must
call cfg80211's results APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a bool and an __le16 called qos, rename the inner __le16
to 'qoshdr' to make it more obvious and to avoid sparse warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a macro here that uses an inner variable 'i' that
also exists in the outer scope - use '_i' in the macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a pointer called 'tidstats' that shadows a bool function
argument with the same name, but we actually only use it once so
just remove the pointer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This variable shadows something that gets generated inside
the tracing macros, which causes sparse to warn. Avoid it
so sparse output is more readable, even if it doesn't seem
to cause any trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the FTM responder settings are changed simultaneously with
the CSA beacon, the buffer size allocated isn't sufficient and
we'll have a heap overrun. Fix this.
While at it, also clean up the ftm_responder assignment, doing
it only if ftm_responder is non-zero is valid as it's 0 to start
with, but not really useful to understand the code.
Fixes: bc847970f4 ("mac80211: support FTM responder configuration/statistics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes stale beacon-int values that would keep a netdev
from going up.
To reproduce:
Create two VAP on one radio.
vap1 has beacon-int 100, start it.
vap2 has beacon-int 240, start it (and it will fail
because beacon-int mismatch).
reconfigure vap2 to have beacon-int 100 and start it.
It will fail because the stale beacon-int 240 will be used
in the ifup path and hostapd never gets a chance to set the
new beacon interval.
Cc: stable@vger.kernel.org
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_sta_opmode_change_notify needs a gfp_t flag to hint the nl80211
stack when allocating new skb, but it is called under tasklet context
here with GFP_KERNEL and kernel will yield a warning about it.
Cc: stable@vger.kernel.org
Fixes: ff84e7bfe1 ("mac80211: Add support to notify ht/vht opmode modification.")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the missing unlock before return from function
ieee80211_mark_sta_auth() in the error handling case.
Cc: stable@vger.kernel.org
Fixes: fc107a9330 ("mac80211: Helper function for marking STA authenticated")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[use result variable/label instead of duplicating]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current mac80211 has provision to update tx status through
ieee80211_tx_status() and ieee80211_tx_status_ext(). But
drivers like ath10k updates the tx status from the skb except
txrate, txrate will be updated from a different path, peer stats.
Using ieee80211_tx_status_ext() in two different paths
(one for the stats, one for the tx rate) would duplicate
the stats instead.
To avoid this stats duplication, ieee80211_tx_rate_update()
is implemented.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[minor commit message editing, use initializers in code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.
Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previous implementation of SAE authentication in infrastructure BSS was
somewhat restricting and not exactly clean way of handling the two
auth() operations. This ended up removing and re-adding the STA entry
for the AP in the middle of authentication and also messing up
authentication state tracking through the sequence of four
Authentication frames. Furthermore, this did not work if the AP ended up
sending out SAE Confirm (auth trans #2) immediately after SAE Commit
(auth trans #1) before the station had time to transmit its SAE Confirm.
Clean up authentication state handling for the SAE case to allow two
rounds of auth() calls without dropping all state between those
operations. Track peer Confirmed status and mark authentication
completed only once both ends have confirmed.
ieee80211_mgd_auth() check for EBUSY cases is now handling only the
pending association (ifmgd->assoc_data) while all pending authentication
(ifmgd->auth_data) cases are allowed to proceed to allow user space to
start a new connection attempt from scratch even if the previously
requested authentication is still waiting completion. This is needed to
avoid making SAE error cases with retries take excessive amount of time
with no means for the user space to stop that (apart from setting the
netdev down).
As an extra bonus, the end of ieee80211_rx_mgmt_auth() can be cleaned up
to avoid the extra copy of the cfg80211_rx_mlme_mgmt() call for ongoing
SAE authentication since the new ieee80211_mark_sta_auth() helper
function can handle both completion of authentication and updates to the
STA entry under the same condition and there is no need to return from
the function between those operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to conditionally replace full allocation of
auth_data to use reallocation for the case of continuing SAE
authentication. Furthermore, there was not really any point in having
this check done so late in the function after having already completed
number of steps that cannot be used anyway in the error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication exchange can be completed in both TX and RX paths for
SAE, so move this common functionality into a helper function to avoid
having to implement practically the same operations in two places when
extending SAE implementation in the following commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there are few packets (e.g. for sampling attempts), the exponentially
weighted variance is usually vastly overestimated, making the resulting data
essentially useless. As far as I know, there has not been any practical use
for this, so let's not waste any cycles on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These rates are highly unlikely to be used quickly, even if the link
deteriorates rapidly. This improves throughput in cases where CCK rates
are not reliable enough to be skipped entirely during sampling.
Sampling these rates regularly can cost a lot of airtime.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Long/short preamble selection cannot be sampled separately, since it
depends on the BSS state. Because of that, sampling attempts to
currently not used preamble modes are not counted in the statistics,
which leads to CCK rates being sampled too often.
Fix statistics accounting for long/short preamble by increasing the
index where necessary.
Fix excessive CCK rate sampling by dropping unsupported sample attempts.
This improves throughput on 2.4 GHz channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes a harmless underflow issue when CCK rates are actively being used
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mi->supported[MINSTREL_CCK_GROUP] needs to be updated
short preamble rates need to be marked as supported regardless of
whether it's currently enabled. Its state can change at any time without
a rate_update call.
Fixes: 782dda00ab ("mac80211: minstrel_ht: move short preamble check out of get_rate")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By storing a shift value for all duration values of a group, we can
reduce precision by a neglegible amount to make it fit into a u16 value.
This improves cache footprint and reduces size:
Before:
text data bss dec hex filename
10024 116 0 10140 279c rc80211_minstrel_ht.o
After:
text data bss dec hex filename
9368 116 0 9484 250c rc80211_minstrel_ht.o
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy-only devices are not very common and the overhead of the extra
code for HT and VHT rates is not big enough to justify all those extra
lines of code to make it optional.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
debugfs entries are cleaned up by debugfs_remove_recursive already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If peer support reception of STBC and LDPC, enable them for better
performance.
Signed-off-by: Chaitanya TK <chaitanya.mgit@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I'm not really sure exactly _why_ I've been carrying a note
for what's probably _years_ to check that we don't do this,
but we clearly do reflect frames back to the station itself
if it sends such.
One way or the other, it's useless since the station doesn't
really need the AP to talk to itself, so suppress it.
While at it, clarify some of the logic by removing skb->data
references in favour of the destination address (pointer) we
already have separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next, which pulled in net, so I can merge a few more
patches that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable j will be initialized at trailing step.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix to return a negative error code -ENOMEM from the kmemdup
error handling case instead of 0.
Fixes: 09b4a4faf9 ("mac80211: introduce capability flags for VHT EXT NSS support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that do not have the BUFF_MMPDU_TXQ flag set will not have a
TXQ for the special TID = 16.
In this case, the last member in the *struct ieee80211_sta* txq array
will be NULL.
We must check this in order not to get a NULL pointer dereference when
iterating the txq array.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
key->sta is only valid after ieee80211_key_link, which is called later
in this function. Because of that, the IEEE80211_KEY_FLAG_RX_MGMT is
never set when management frame protection is enabled.
Fixes: e548c49e6d ("mac80211: add key flag for management keys")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Monitor mode interfaces with the active flag are passed down to the driver.
Drivers using TXQ expect that all interfaces have allocated TXQs before
they get added.
Fixes: 79af1f8661 ("mac80211: avoid allocating TXQs that won't be used")
Cc: stable@vger.kernel.org
Reported-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TX status reporting to ieee80211s is through ieee80211s_update_metric.
There are two problems about ieee80211s_update_metric:
1. The purpose is to estimate the fail probability
to a specific link. No need to restrict to data frame.
2. Current implementation does not work if wireless driver does not
pass tx_status with skb.
Fix this by removing ieee80211_is_data condition, passing
ieee80211_tx_status directly to ieee80211s_update_metric, and
putting it in both __ieee80211_tx_status and ieee80211_tx_status_ext.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the TDLS setup happens over a connection to an AP that
doesn't have QoS, we nevertheless assign a non-zero TID
(skb->priority) and queue mapping, which may confuse us or
drivers later.
Fix it by just assigning the special skb->priority and then
using ieee80211_select_queue() just like other data frames
would go through.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In our environment running lots of mesh nodes, we are seeing the
pending queue hang periodically, with the debugfs queues file showing
lines such as:
00: 0x00000000/348
i.e. there are a large number of frames but no stop reason set.
One way this could happen is if queue processing from the pending
tasklet exited early without processing all frames, and without having
some future event (incoming frame, stop reason flag, ...) to reschedule
it.
Exactly this can occur today if ieee80211_tx() returns false due to
packet drops or power-save buffering in the tx handlers. In the
past, this function would return true in such cases, and the change
to false doesn't seem to be intentional. Fix this case by reverting
to the previous behavior.
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both old and new cannot be NULL at the same time, hence checking
new when old is not NULL is unnecessary.
Also, notice that new is being dereferenced before it is checked:
idx = new->conf.keyidx;
The above triggers a static code analysis warning.
Address this by removing the NULL check on new and adding a code
comment based on the following piece of code:
387 /* caller must provide at least one old/new */
388 if (WARN_ON(!new && !old))
389 return 0;
Addresses-Coverity-ID: 1473176 ("Dereference before null check")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardwares have limitations on the packets' type in AMSDU.
Add an optional driver callback to determine if two skbs can
be used in the same AMSDU or not.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may have AMSDU size limitation per TID, due to
HW constrains. Add an option to set this limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a TXQ abstraction for non-data packets that need
powersave buffering. Since the AP cannot sleep, in case
of station we can use this TXQ for all management frames,
regardless if they are bufferable. Add HW flag to allow
that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities
and update drivers' 11ax capabilities and mac80211's debugfs
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After masking the he_oper_params, to get the requested values as
integers one must rshift and not lshift. Fix that by using the
le32_get_bits() macro.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
[converted to use le32_get_bits()]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For certain sounding frames, it may be useful to report them
to userspace even though they don't have a PSDU in order to
determine the PHY parameters (e.g. VHT rate/stream config.)
Add support for this to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise the offchannel frame might be queued due to
IEEE80211_QUEUE_STOP_REASON_PS and later dropped (in
ieee80211_tx_frags()). Anyway, it doesn't make much sense to wake up
the device during ROC.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a frame is dropped for any reason, mac80211 wouldn't report the TX
status back to user space.
As the user space may rely on the TX_STATUS to kick its state
machines, resends etc, it's better to just report this frame as not
acked instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rekeying PTK keys without "Extended Key ID for Individually Addressed
Frames" did use a procedure not suitable to replace in-use keys and
could caused the following issues:
1) Freeze caused by incoming frames:
If the local STA installed the key prior to the remote STA we still
had the old key active in the hardware when mac80211 switched over
to the new key.
Therefore there was a window where the card could hand over frames
decoded with the old key to mac80211 and bump the new PN (IV) value
to an incorrect high number. When it happened the local replay
detection silently started to drop all frames sent with the new key.
2) Freeze caused by outgoing frames:
If mac80211 was providing the PN (IV) and handed over a clear text
frame for encryption to the hardware prior to a key change the
driver/card could have processed the queued frame after switching
to the new key. This bumped the PN value on the remote STA to an
incorrect high number, tricking the remote STA to discard all frames
we sent later.
3) Freeze caused by RX aggregation reorder buffer:
An aggregation session started with the old key and ending after the
switch to the new key also bumped the PN to an incorrect high number,
freezing the connection quite similar to 1).
4) Freeze caused by repeating lost frames in an aggregation session:
A driver could repeat a lost frame and encrypt it with the new key
while in a TX aggregation session without updating the PN for the
new key. This also could freeze connections similar to 2).
5) Clear text leak:
Removing encryption offload from the card cleared the encryption
offload flag only after the card had deleted the key and we did not
stop TX during the rekey. The driver/card could therefore get
unencrypted frames from mac80211 while no longer be instructed to
encrypt them.
To prevent those issues the key install logic has been changed:
- Mac80211 divers known to be able to rekey PTK0 keys have to set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0,
- mac80211 stops queuing frames depending on the key during the replace
- the key is first replaced in the hardware and after that in mac80211
- and mac80211 stops/blocks new aggregation sessions during the rekey.
For drivers not setting
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 the user space must avoid PTK
rekeys if "Extended Key ID for Individually Addressed Frames" is not
being used. Rekeys for mac80211 drivers without this flag will generate a
warning and use an extra call to ieee80211_flush_queues() to both
highlight and try to prevent the issues with not updated drivers.
The core of the fix changes the key install procedure from:
- atomic switch over to the new key in mac80211
- remove the old key in the hardware (stops encryption offloading, fall
back to software encryption with a potential clear text packet leak
in between)
- delete the inactive old key in mac80211
- enable hardware encryption offloading for the new key
to:
- if it's a PTK mark the old key as tainted to drop TX frames with the
outgoing key
- replace the key in hardware with the new one
- atomic switch over to the new (not marked as tainted) key in
mac80211 (which also resumes TX)
- delete the inactive old key in mac80211
With the new sequence the hardware will be unable to decrypt frames
encrypted with the old key prior to switching to the new key in mac80211
and thus prevent PNs from packets decrypted with the old key to be
accounted against the new key.
For that to work the drivers have to provide a clear boundary.
Mac80211 drivers setting @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 confirm
to provide it and mac80211 will then be able to correctly rekey in-use
PTK keys with those drivers.
The mac80211 requirements for drivers to set the flag have been added to
the "Hardware crypto acceleration" documentation section. It drills down
to:
The drivers must not hand over frames decrypted with the old key to
mac80211 once the call to set_key() with %DISABLE_KEY has been
completed. It's allowed to either drop or continue to use the old key
for any outgoing frames which are already in the queues, but it must not
send out any of them unencrypted or encrypted with the new key.
Even with the new boundary in place aggregation sessions with the
reorder buffer are problematic:
RX aggregation session started prior and completed after the rekey could
still dump frames received with the old key at mac80211 after it
switched over to the new key. This is side stepped by stopping all (RX
and TX) aggregation sessions when replacing a PTK key and hardware key
offloading.
Stopping TX aggregation sessions avoids the need to get
the PNs (IVs) updated in frames prepared for the old key and
(re)transmitted after the switch to the new key. As a bonus it improves
the compatibility when the remote STA is not handling rekeys as it
should.
When using software crypto aggregation sessions are not stopped.
Mac80211 won't be able to decode the dangerous frames and discard them
without special handling.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[trim overly long rekey warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As before with HE, the data needs to be provided by the
driver in the skb head, since there's not enough space
in the skb CB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it possibly for drivers to adjust the default skb_pacing_shift
by storing it in the hardware struct.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[adjust commit log, move & adjust comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When taking VHT capabilities for a station, copy the new
fields if we support them as a transmitter. Also adjust
the maximum bandwidth the station supports appropriately.
Also, since it was missing, copy tx_highest and rx_highest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With newer VHT implementations, it's necessary to look at the
HT operation's CCFS2 field to identify the actual bandwidth
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on whether or not rate control supports selecting
rates depending on the bandwidth, we can use VHT extended
NSS support. In essence, this is dot11VHTExtendedNSSBWCapable
from the spec, since depending on that we'll need to parse
the bandwidth.
If needed, also set/clear the VHT Capability Element bit for
this capability so that we don't advertise it erroneously or
don't advertise it when we actually use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, If AP advertises HE capabilities, set to true
bss_conf::he_supported so that the Driver knows about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to also use the TXQ abstraction with
non-data packets that need powersave buffering, so add a
hardware flag to allow this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These checks aren't necessary, cfg80211 never passes NULL.
Some static checkers complain about the missing checks on
the next line, but really the NULL checks are unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Export HE capabilities information via debugfs, similar to HT & VHT.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
-----BEGIN PGP SIGNATURE-----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=lLBA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When tracing is enabled, all the debug messages are recorded and must
not exceed MAX_MSG_LEN (100) columns. Longer debug messages grant the
user with:
WARNING: CPU: 3 PID: 32642 at /tmp/wifi-core-20180806094828/src/iwlwifi-stack-dev/net/mac80211/./trace_msg.h:32 trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Workqueue: phy1 ieee80211_iface_work [mac80211]
RIP: 0010:trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Call Trace:
__sdata_dbg+0xbd/0x120 [mac80211]
ieee80211_ibss_rx_queued_mgmt+0x15f/0x510 [mac80211]
ieee80211_iface_work+0x21d/0x320 [mac80211]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver fails to properly prepare for the channel
switch, mac80211 will disconnect. If the CSA IE had mode
set to 1, it means that the clients are not allowed to send
any Tx on the current channel, and that includes the
deauthentication frame.
Make sure that we don't send the deauthentication frame in
this case.
In iwlwifi, this caused a failure to flush queues since the
firmware already closed the queues after having parsed the
CSA IE. Then mac80211 would wait until the deauthentication
frame would go out (drv_flush(drop=false)) and that would
never happen.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When performing a channel switch flow for a managed interface, the
flow did not update the bandwidth of the AP station and the rate
scale algorithm. In case of a channel width downgrade, this would
result with the rate scale algorithm using a bandwidth that does not
match the interface channel configuration.
Fix this by updating the AP station bandwidth and rate scaling algorithm
before the actual channel change in case of a bandwidth downgrade, or
after the actual channel change in case of a bandwidth upgrade.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We hit a problem with iwlwifi that was caused by a bug in
mac80211. A bug in iwlwifi caused the firwmare to crash in
certain cases in channel switch. Because of that bug,
drv_pre_channel_switch would fail and trigger the restart
flow.
Now we had the hw restart worker which runs on the system's
workqueue and the csa_connection_drop_work worker that runs
on mac80211's workqueue that can run together. This is
obviously problematic since the restart work wants to
reconfigure the connection, while the csa_connection_drop_work
worker does the exact opposite: it tries to disconnect.
Fix this by cancelling the csa_connection_drop_work worker
in the restart worker.
Note that this can sound racy: we could have:
driver iface_work CSA_work restart_work
+++++++++++++++++++++++++++++++++++++++++++++
|
<--drv_cs ---|
<FW CRASH!>
-CS FAILED-->
| |
| cancel_work(CSA)
schedule |
CSA work |
| |
Race between those 2
But this is not possible because we flush the workqueue
in the restart worker before we cancel the CSA worker.
That would be bullet proof if we could guarantee that
we schedule the CSA worker only from the iface_work
which runs on the workqueue (and not on the system's
workqueue), but unfortunately we do have an instance
in which we schedule the CSA work outside the context
of the workqueue (ieee80211_chswitch_done).
Note also that we should probably cancel other workers
like beacon_connection_loss_work and possibly others
for different types of interfaces, at the very least,
IBSS should suffer from the exact same problem, but for
now, do the minimum to fix the actual bug that was actually
experienced and reproduced.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 9236c4523e5b ("mac80211: limit wmm params to comply
with ETSI requirements"), we have limited the WMM parameters to
comply with 802.11 and ETSI standard. Mistakenly the TXOP value
was caluclated wrong. Fix it by taking the minimum between
802.11 to ETSI to make sure we are not violating both.
Fixes: e552af0581 ("mac80211: limit wmm params to comply with ETSI requirements")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initialize 'n' to 2 in order to take into account also the first
packet in the estimation of max_subframe limit for a given A-MSDU
since frag_tail pointer is NULL when ieee80211_amsdu_aggregate
routine analyzes the second frame.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the error path of changing the SKB headroom of the second
A-MSDU subframe, we would not account for the already-changed
length of the first frame that just got converted to be in
A-MSDU format and thus is a bit longer now.
Fix this by doing the necessary accounting.
It would be possible to reorder the operations, but that would
make the code more complex (to calculate the necessary pad),
and the headroom expansion should not fail frequently enough
to make that worthwhile.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not start to aggregate packets in a A-MSDU frame (converting the
first subframe to A-MSDU, adding the header) if max_tx_fragments or
max_amsdu_subframes limits are already exceeded by it. In particular,
this happens when drivers set the limit to 1 to avoid A-MSDUs at all.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
[reword commit message to be more precise]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building building AMSDU from non-linear SKB, we hit a
kernel panic when trying to push the padding to the tail.
Instead, put the padding at the head of the next subframe.
This also fixes the A-MSDU subframes to not have the padding
accounted in the length field and not have pad at all for
the last subframe, both required by the spec.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Reviewed-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE 802.11-2016 14.10.8.3 HWMP sequence numbering says:
If it is a target mesh STA, it shall update its own HWMP SN to
maximum (current HWMP SN, target HWMP SN in the PREQ element) + 1
immediately before it generates a PREP element in response to a
PREQ element.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Modify the API to include all ACK frames in average ACK
signal strength reporting, not just ACKs for data frames.
Make exposing the data conditional on implementing the
extended feature flag.
This is how it was really implemented in mac80211, update
the code there to use the new defines and clean up some of
the setting code.
Keep nl80211.h source compatibility by keeping the old names.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[rewrite commit log, change compatibility to be old=new
instead of the other way around, update kernel-doc,
roll in mac80211 changes, make mac80211 depend on valid
bit instead of HW flag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current mac80211 WDS (4-address mode) can be used to cover most of the
Multi-AP requirements for Data frames per the WFA Multi-AP Specification v1.0.
When configuring AP/STA interfaces in 4-address mode, they are able to function
as fronthaul AP/backhaul STA of Multi-AP device complying below
Tx, Rx requirements except one missing STA Rx requirement added by this patch.
Multi-AP specification section 14.1 describes the following requirements:
Transmitter requirements
------------------------
1. Fronthaul AP
i) When DA!=RA of backhaul STA, must use 4-address format
ii) When DA==RA of backhaul STA, shall use either 3-address
or 4-address format with RA updated with STA MAC
(mac80211 support 4-address format via AP/VLAN interface)
2. Backhaul STA
i) When SA!=TA of backhaul STA, must use 4-address format
ii) When SA==TA of backhaul STA, shall use either 3-address
or 4-address format with RA updated with AP MAC
(mac80211 support 4-address format via use_4addr)
Receiver requirements
---------------------
1. Fronthaul AP
i) When SA!=TA of backhaul STA, must support receiving 4-address
format frames
ii) When SA==TA of backhaul STA, must support receiving both
3-address and 4-address format frames
(mac80211 support both 3-addr & 4-addr via AP/VLAN interface)
2. Backhaul STA
i) When DA!=RA of backhaul STA, must support receiving 4-address
format frames
ii) When DA==RA of backhaul STA, must support receiving both
3-address and 4-address format frames
(mac80211 support only receiving 4-address format via
use_4addr)
This patch addresses the above Rx requirement (ii) for backhaul STA to receive
unicast (DA==RA) 3-address frames in addition to 4-address frames.
The current design doesn't accept 3-address frames when configured in 4-address
mode (use_4addr). Hence add a check to allow 3-address frames when DA==RA of
backhaul STA (adhering to Table 9-26 of IEEE Std 802.11™-2016).
This case was tested with a bridged station interface when associated with
a non-mac80211 based vendor AP implementation using 3-address frames for WDS.
STA was able to support the Multi-AP Rx requirement when DA==RA. No issues,
no loops seen when tested with mac80211 based AP as well.
Verified and confirmed all other Tx and Rx requirements of AP and STA for
Multi-AP respectively. They all work using the current mac80211-WDS design.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes, it is required to stop the transmissions momentarily and
resume it later; stopping the txqs becomes very critical in scenarios where
the packet transmission has to be ceased completely. For example, during
the hardware restart, during off channel operations,
when initiating CSA(upon detecting a radar on the DFS channel), etc.
The TX queue stop/start logic in mac80211 works well in stopping the TX
when drivers make use of netdev queues, i.e, when Qdiscs in network layer
take care of traffic scheduling. Since the devices implementing
wake_tx_queue can run without Qdiscs, packets will be handed to mac80211
directly without queueing them in the netdev queues.
Also, mac80211 does not invoke any of the
netif_stop_*/netif_wake_* APIs if wake_tx_queue is implemented.
Since the queues are not stopped in this case, transmissions can continue
and this will impact negatively on the operation of the wireless device.
For example,
During hardware restart, we stop the netdev queues so that packets are
not sent to the driver. Since ath10k implements wake_tx_queue,
TX queues will not be stopped and packets might reach the hardware while
it is restarting; this can make hardware unresponsive and the only
possible option for recovery is to reboot the entire system.
There is another problem to this, it is observed that the packets
were sent on the DFS channel for a prolonged duration after radar
detection impacting the channel closing time.
We can still invoke netif stop/wake APIs when wake_tx_queue is implemented
but this could lead to packet drops in network layer; adding stop/start
logic for software TXQs in mac80211 instead makes more sense; the change
proposed adds the same in mac80211.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller
Colin Ian King
Felix Fietkau
Alexei Avshalom Lazar
John Crispin
Ben Greear
Arend van Spriel
Johannes Berg
Shay Bar
Karthikeyan Periyasamy
Brian Norris
Sven Eckelmann
Lorenzo Bianconi
Manikanta Pubbisetty
Alexander Wetzel
Erik Stromdahl
Greg Kroah-Hartman
Emmanuel Grumbach
Linus Torvalds
Ard Biesheuvel
Thomas Gleixner
James Prestwood
Naftali Goldstein
Yibo Zhao
Florian Westphal
Pradeep Kumar Chitrapu
Thomas Pedersen
Jouni Malinen
YueHaibing
Yu Wang
Rajkumar Manoharan
Dan Carpenter
Ashok Raj Nagarajan
Julius Niedworok
Sergey Matyukevich
Sara Sharon
Bhagavathi Perumal S
Narayanraddi Masti
Andrei Otcheretianski
Paolo Abeni
Herbert Xu
Liad Kaufman
Jouni Malinen
Toke Høiland-Jørgensen
Wei Yongjun
Rakesh Pillai
Ilan Peer
Mathieu Malaterre
Balaji Pothunoori
Julan Hsu
Toke Høiland-Jørgensen
Bob Copeland
Shaul Triebitz
Eric Biggers
Yan-Hsuan Chuang
Anilkumar Kolli
Chaitanya T K
Masashi Honma
Yuan-Chi Pang
Gustavo A. R. Silva
Wen Gong
Ido Yariv
Dreyfuss, Haim
Lorenzo Bianconi
Sathishkumar Muruganandam
Dedy Lansky