ttyprintk driver calls tty_unregister_driver() wrongly in the error
path of tty_register_driver(). Also, setting ttyprintk_driver to NULL
is utterly superfluous, so let's get rid of it, too.
Reported-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 driver now reports many of these:
serial8250: too much work for irq4
These messages turned out to be common these days with a use of
virtualization. I tried to increase the limit of processed characters
in commit e7328ae184 (serial: 8250,
increase PASS_LIMIT) in 2011. It was raised from 256 to 512, but it is
still not enough, apparently.
So disable the warning unless somebody turns on DEBUG (or
DYNAMIC_DEBUG _and_ the message).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Martin Pluskal <mpluskal@suse.com>
Reported-by: Takashi Iwai <tiwai@suse.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
References: https://bugzilla.novell.com/show_bug.cgi?id=868394
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These serial drivers were removed in kernel v3.1, so we can drop their
documentation files and references to their magic numbers and
parameters.
There are still references to these old drivers in
Documentation/devices.txt but I'm afraid they can't be removed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lack of pm_runtime_resume handling for the device state leads into
device wake-up interrupts not working after a while for runtime PM.
Also, serial-omap is confused about the use of device_may_wakeup.
The checks for device_may_wakeup should only be done for suspend and
resume, not for pm_runtime_suspend and pm_runtime_resume. The wake-up
events for PM runtime should always be enabled.
The lack of pm_runtime_resume handling leads into device wake-up
interrupts not working after a while for runtime PM.
Rather than try to patch over the issue of adding complex tests to
the pm_runtime_resume, let's fix the issues properly:
1. Make serial_omap_enable_wakeup deal with all internal PM state
handling so we don't need to test for up->wakeups_enabled elsewhere.
Later on once omap3 boots in device tree only mode we can also
remove the up->wakeups_enabled flag and rely on the wake-up
interrupt enable/disable state alone.
2. Do the device_may_wakeup checks in suspend and resume only,
for runtime PM the wake-up events need to be always enabled.
3. Finally just call serial_omap_enable_wakeup and make sure we
call it also in pm_runtime_resume.
4. Note that we also have to use disable_irq_nosync as serial_omap_irq
calls pm_runtime_get_sync.
Fixes: 2a0b965cfb (serial: omap: Add support for optional wake-up)
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is closed, uart_close() takes care of shutting down the
hardware, and powering it down.
When a serial port is unbound while in use, uart_close() bypasses all of
this, as this is supposed to be done through uart_hangup() (invoked via
tty_vhangup() in uart_remove_one_port()).
However, uart_hangup() does not set the hardware's power state, leaving it
powered up. This may also lead to unbounded nesting counts in clock and
power management, depending on their internal implementation.
Make sure to power down the port in uart_hangup(), except when the port is
used as a serial console.
For serial consoles, this operation must be postponed until after the port
becomes completely unused. This case is not fixed yet, as it depends on a
(future) fix for the tty->count vs. port->count imbalance on failed
uart_open().
After this, the module clock used by the sh-sci driver is disabled on
unbind while the serial port is in use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The amba-pl011.c driver sets DMA burst size equal to FIFO trigger level.
If now exactly DMA burst size bytes are received, the DMAC will retrieve
them all and no Rx timeout interrupt will be generated. To fix that set
the burst size to half the FIFO trigger level.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As far as I know the Timberdale chip was only used as a companion for
Intel Atom E600 series processors. As such, its drivers are only
useful on X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver, like several others, uses the upper bits of the character
to track both real and dummy state. Unfortunately it neglects to mask
these bits properly when passing the character data around. This means
neither break detection nor sysrq character handling work correctly.
This patch adds the requires masking and has been tested to confirm
that it correctly handles magic sysrq sequences on ST's B2020 board.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 63e3ad3252,
since this not works as expected and produce runtime error:
BUG: sleeping function called from invalid context at drivers/tty/serial/clps711x.c:379
in_atomic(): 0, irqs_disabled(): 128, pid: 287, name: mount
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial_core ring buffer empties just as the tty layer receives
an XOFF, then start_tx will never be called when the tty layer
receives an XON as the serial_core ring buffer is empty. This will
possibly leave a few bytes trapped in the fifo for drivers that
disable the transmitter when flow controlled.
Signed-off-by: Seth Bollinger <sethb@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the
common scheme and prefix device with "efm32-". The old compatible string
is left in place until arch/arm/boot/dts/efm32* is fixed.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only ws2012r2 hosts support the ability to reconnect to the host on VMBUS. This functionality
is needed by kexec in Linux. To use this functionality we need to negotiate version 3.0 of the
VMBUS protocol.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The English and Korean translations were updated, the Chinese and Japanese
weren't.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The topology_##name() macro does not use its argument when CONFIG_SMP is not
set, as it ultimately calls the cpu_data() macro.
So we avoid maintaining a possibly unused `cpu' variable, to avoid the
following compilation warning:
drivers/base/topology.c: In function ‘show_physical_package_id’:
drivers/base/topology.c:103:118: warning: unused variable ‘cpu’ [-Wunused-variable]
define_id_show_func(physical_package_id);
drivers/base/topology.c: In function ‘show_core_id’:
drivers/base/topology.c:106:106: warning: unused variable ‘cpu’ [-Wunused-variable]
define_id_show_func(core_id);
This can be seen with e.g. x86 defconfig and CONFIG_SMP not set.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org> # 3.10.x
Cc: <stable@vger.kernel.org> # 3.13.x
Cc: <stable@vger.kernel.org> # 3.14.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a Chinese translated version of Documentation/io_ordering.txt
Signed-off-by: Lin Yongting <linyongting@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return the appropriate error code and handle the case when the target
file exists correctly. This fixes a bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save some characters by using to_pci_dev() instead of container_of().
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, tsi148_master_set() assumed the address contained in its
PCI bus resource represented the actual PCI bus address. This is a fine
assumption on some platforms. However, on platforms that don't use a
1:1 (CPU:PCI) mapping this results in the tsi148 driver configuring an
invalid master window translation.
This patch updates the vme_tsi148 driver to first convert the address
contained in the PCI bus resource into a PCI bus address before using
it.
[asierra: account for pcibios_resource_to_bus() prototype change]
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects a typo where "vme_base" was used instead of
"*vme_base". The typo resulted in an incorrect value being returned
to userspace (via vme_user).
It also removes the following compile warning on some platforms:
warning: cast from pointer to integer of different size
[asierra: commit title/log rewording]
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__w1_attach_slave_device calls device_add which calls w1_bus_notify
which calls the w1_bq27000 slave driver, which calls
platform_device_add and device_add and deadlocks on getting
&(&priv->bus_notifier)->rwsem as it is still held in the previous
device_add. This avoids the problem by processing the family
add/remove outside of the slave device_add call.
Commit 47eba33a09 introduced this deadlock and added
a KOBJ_ADD, as the add was already reported in device_register two add
events were being sent. This change suppresses the device_register
add so that any slave device sysfs entries are setup before the add
goes out.
Belisko Marek reported this change fixed the deadlock he was seeing on
ARM device tree, while testing on my x86-64 system never saw the
deadlock.
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: David Fries <David@Fries.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the message type is W1_MASTER_CMD or W1_SLAVE_CMD, then a reference
is taken when searching for the slave or master device. If there
isn't any following data m->len (mlen is a copy) is 0 and packing up
the message for later execution is skipped leaving nothing to
decrement the reference counts.
Way back when, m->len was checked before the search that increments the
reference count, but W1_LIST_MASTERS has no additional data, the check
was moved in 9be62e0b2f causing this bug.
This change reorders to put the check before the reference count is
incremented avoiding the problem.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are also two allocations with GFP_KERNEL in the pre-/post_reset
code paths. That is no good because that is a part of the SCSI error handler.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
intfdata is set only after scsi_scan(). uas_pre_reset() however
needs intfdata to be valid and will follow the NULL pointer
killing khubd. intfdata must be preemptively set before the
host is registered and undone in the error case.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quote Dan:
The patch e36e64930cff: "uas: Use GFP_NOIO rather then GFP_ATOMIC
where possible" from Nov 7, 2013, leads to the following static
checker warning:
drivers/usb/storage/uas.c:806 uas_eh_task_mgmt()
error: scheduling with locks held: 'spin_lock:lock'
Some other allocations under spinlock are not caught.
The fix essentially reverts e36e64930c
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is checking NULL before dereferncing but
it need to add "return".
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By specifying NO_UNION_NORMAL the ACM driver does only use the first two
USB interfaces (modem data & control). The AT Port, Diagnostic and NMEA
interfaces are left to the USB serial driver.
Signed-off-by: Michael Ulbricht <michael.ulbricht@systec-electronic.com>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Power control of hub ports target the CLEAR_FEATURE and SET_FEATURE
requests to ports, not to the hub. Fix the hub control function to
detect the request correctly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ret variable is not initialized in all code paths of the
ohci_jz4740_hub_control function. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid memory fetch underflows with larger USB transfers, Tegra SoCs
need txfill_tuning's txfifothresh register field set to a non-default
value. Add a custom reset override in order to set this up.
These values are recommended practice for all Tegra chips. However,
I've only noticed practical problems when not setting them this way on
systems using Tegra124. Hence, CC: stable only for recent kernels which
actually support Tegra124.
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch 'b8efdaf USB: EHCI: add check for wakeup/suspend race'
adds a check for possible race between suspend and wakeup interrupt,
and thereby it returns -EBUSY as error code if there's a wakeup
interrupt.
So the platform host controller should not proceed further with
its suspend callback, rather should return immediately to avoid
powering down the essential things, like phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch 'b8efdaf USB: EHCI: add check for wakeup/suspend race'
adds a check for possible race between suspend and wakeup interrupt,
and thereby it returns -EBUSY as error code if there's a wakeup
interrupt.
So the platform host controller should not proceed further with
its suspend callback, rather should return immediately to avoid
powering down the essential things, like phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in hcd-pci.c that matches up EHCI controllers with their
companion UHCI or OHCI controllers assumes that the private drvdata
fields don't get set too early. However, it turns out that this field
gets set by usb_create_hcd(), before hcd-pci expects it, and this can
result in a crash when two controllers are probed in parallel (as can
happen when a new controller card is hotplugged).
The companions_rwsem lock was supposed to prevent this sort of thing,
but usb_create_hcd() is called outside the scope of the rwsem.
A simple solution is to check that the root-hub pointer has been
initialized as well as the drvdata field. This doesn't happen until
usb_add_hcd() is called; that call and the check are both protected by
the rwsem.
This patch should be applied to stable kernels from 3.10 onward.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Stefani Seibold <stefani@seibold.net>
Tested-by: Stefani Seibold <stefani@seibold.net>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If acm_submit_read_urbs() fails in acm_port_activate(), error handling
code calls usb_autopm_put_interface() while it is already called
before acm_submit_read_urbs(). The patch reorganizes error handling code
to avoid double decrement of USB interface's PM-usage counter.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 8e493ca176 ("USB: usb_wwan: fix
bulk-urb allocation") by making sure to require both bulk-in and out
endpoints during port probe.
The original option driver (which usb_wwan is based on) was written
under the assumption that either endpoint could be missing, but
evidently this cannot have been tested properly. Specifically, it would
handle opening a device without bulk-in (but would blow up during resume
which was implemented later), but not a missing bulk-out in write()
(although it is handled in some places such as write_room()).
Fortunately (?), the driver also got the test for missing endpoints
wrong so the urbs were in fact always allocated, although they would be
initialised using the wrong endpoint address (0) and any submission of
such an urb would fail.
The commit mentioned above fixed the test for missing endpoints but
thereby exposed the other bugs which would now generate null-pointer
exceptions rather than failed urb submissions.
The regression was introduced in v3.7, but the offending commit was also
marked for stable.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1ebca9dad5.
This device was erroneously added to the sierra driver even though it's
not a Sierra device and was already handled by the option driver.
Cc: Richard Farina <sidhayn@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zero-initializing ether_type masked that the ether type would never be
obtained for 8021x packets and the comparison against eapol_type
would always fail.
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zero-initializing ether_type masked that the ether type would never be
obtained for 8021x packets and the comparison against eapol_type
would always fail.
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chameleon_parse_cells() bails out if chameleon descriptor type is
invalid but does not free the storage 'header' points to.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ignore client writing state during cb completion to fix a memory
leak.
When moving cbs to the completion list we should not look at
writing_state as this state can be already overwritten by next
write, the fact that a cb is on the write waiting list means
that it was already written to the HW and we can safely complete it.
Same pays for wait in poll handler, we do not have to check the state
wake is done after completion list processing.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NM and SPS FW types that may run on ME device on server platforms
do not have valid MEI/HECI interface and driver should not
be bound to it as this might lead to system hung.
In practice not all BIOSes effectively hide such devices from the
OS and in some cases it is not possible.
We determine FW type by examining Host FW status registers in order to
unbind the driver.
In this patch we are adding check for ME on Cougar Point, Lynx Point
Devices
Cc: stable <stable@vger.kernel.org> # 3.10+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This buffer over was detected using static analysis:
drivers/isdn/icn/icn.c:1325 icn_command()
error: format string overflow. buf_size: 60 length: 98
The calculation for the length of the string is off because it assumes
that the dial[] buffer holds a 50 character string, but actually it is
at most 31 characters and NUL. I have removed the dial[] buffer because
it isn't needed.
The maximum length of the string is actually 79 characters and a NUL. I
have made the cbuf[] array large enough to hold it and changed the
sprintf() to an snprintf() as a further safety enhancement.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai
Jiri Slaby
Jean Delvare
Tony Lindgren
Geert Uytterhoeven
Guennadi Liakhovetski
Daniel Thompson
Alexander Shiyan
Seth Bollinger
Uwe Kleine-König
Sanjay Singh Rawat
K. Y. Srinivasan
Vincent Stehlé
Lin Yongting
Brian Norris
Aaron Sierra
Joe Schultz
David Fries
Oliver Neukum
Daeseok Youn
Michael Ulbricht
Laurent Pinchart
Stephen Warren
Vivek Gautam
Alan Stern
Alexey Khoroshilov
Peter Chen
Johan Hovold
Aaron Sanders
Tristan Bruns
Daniele Palmas
Michele Baldessari
Larry Finger
Christoph Jaeger
Kees Cook
Alexander Usyskin
Tomas Winkler
Dan Carpenter