If the PHY is halted on stop, then do not set the state to PHY_UP. This
ensures the phy will be restarted later in phy_start when the machine is
started again.
Fixes: 00db8189d9 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.")
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Acked-by: Xander Huff <xander.huff@ni.com>
Acked-by: Kyle Roeschley <kyle.roeschley@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can build modular code that uses mdiobus_register_board_info() which would
lead to linking failure since this symbol is not expoerted.
Fixes: 648ea01340 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hwmon temperature sensor devices is registered using a devm_hwmon
API call. The marvell_release() would then manually free the device,
not using a devm_hmon API, resulting in the device being removed
twice, leading to a crash in kernfs_find_ns() during the second
removal.
Remove the manual removal, which makes marvell_release() empty, so
remove it as well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 0b04680fda ("phy: marvell: Add support for temperature sensor")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Generic PHY driver is a catch-all PHY driver and it should preserve
whatever prior initialization has been done by boot loader or firmware
agents. For specific PHY device configuration it is expected that a
specialized PHY driver would take over that role.
Resetting the generic PHY was a bad idea that has lead to several
complaints and downstream workarounds e.g: in OpenWrt/LEDE so restore
the behavior prior to 87aa9f9c61 ("net: phy: consolidate PHY
reset in phy_init_hw()").
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan's static checker caught a potential code path in phy_state_machine() where
we were not checking phydev->drv which is in phy_aneg_done().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 25149ef9d2 ("net: phy: Check phydev->drv")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are number of function calls, originating from user-space,
typically through the Ethernet driver that can make us crash by
dereferencing phydev->drv which will be NULL once we unbind the driver
from the PHY.
There are still functional issues that prevent an unbind then rebind to
work, but these will be addressed separately.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library does not deal very well with bind and unbind events. The first
thing we would see is that we were not properly canceling the PHY state machine
workqueue, so we would be crashing while dereferencing phydev->drv since there
is no driver attached anymore.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Generic PHY drivers gets assigned after we checked that the current
PHY driver is NULL, so we need to check a few things before we can
safely dereference d->driver. This would be causing a NULL deference to
occur when a system binds to the Generic PHY driver. Update
phy_attach_direct() to do the following:
- grab the driver module reference after we have assigned the Generic
PHY drivers accordingly, and remember we came from the generic PHY
path
- update the error path to clean up the module reference in case the
Generic PHY probe function fails
- split the error path involving phy_detacht() to avoid double free/put
since phy_detach() does all the clean up
- finally, have phy_detach() drop the module reference count before we
call device_release_driver() for the Generic PHY driver case
Fixes: cafe8df8b9 ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LED Mode:
Microsemi PHY support 2 LEDs (LED[0] and LED[1]) to display different
status information that can be selected by setting LED mode.
LED Mode parameter (vsc8531, led-0-mode) and (vsc8531, led-1-mode) get
from Device Tree.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the lane swapping (called
"port mirroring" in PHY's CFG4 register) feature of the DP83867 TI's PHY
device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the BCM74371 PHY ID to the list of supported chips. This is a 28nm
technology Gigabit PHY SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e1545 PHYs are discrete Marvell PHYs, found in a quad package on
the zii-devel-b board. Add support for it to the Marvell PHY driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 Ethernet switch has internal PHYs. These PHYs don't have
an model ID in the ID2 register. So the MDIO driver in the switch
intercepts reads to this register, and returns the switch family ID.
Extend the Marvell PHY driver by including this ID, and treat the PHY
as a 88E1540.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device match tables for both the xgene_enet driver and its phy driver
have forward declarations that declare an array without a length, leading
to a clang warning when they are not followed by an actual defitinition:
drivers/net/ethernet/apm/xgene/../../../phy/mdio-xgene.h:135:34: warning: tentative array definition assumed to have one element
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning: tentative array definition assumed to have one element
The declarations for the mdio driver are even in a header file, so they
cause duplicate definitions of the tables for each file that includes
them.
This removes all four forward declarations and moves the actual
definitions up a little, so they are in front of their first user. For
the OF match tables, this means having to remove the #ifdef around them,
and passing the actual structure into of_match_device(). This has no
effect on the generated object code though, as the of_match_device
function has an empty stub that does not evaluate its argument, and
the symbol gets dropped either way.
Fixes: 43b3cf6634 ("drivers: net: phy: xgene: Add MDIO driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extra BCM54612E code in PHY driver isn't really aneg specific. Even
without it aneg works OK but the problem is no packets pass through PHY.
Moreover putting this code inside config_aneg callback didn't allow
resuming PHY correctly. When driver called phy_stop and phy_start it was
putting PHY machine into RESUMING state. After that machine was
switching into AN and NOLINK without ever calling phy_start_aneg. This
prevented this extra setup from being called and PHY didn't work.
This change has been verified to fix network on BCM47186B0 SoC device
with BCM54612E.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pr commit "net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause"
this phy driver should not set these feature bits.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Fixes: 9d162ed69f ("net: phy: micrel: add support for KSZ8795")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling delay skew and GTXCLK
bits.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is adds support for the PHYs in the KSZ8795 5port managed switch.
It will allow to detect the link between the switch and the soc
and uses the same read_status functions as the KSZ8873MLL switch.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had two defines for the same bit (both were used with the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC register).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 5b4e290051 ("net: phy: broadcom: add
bcm54xx_auxctl_read") we have a reading helper so use it and avoid code
duplication.
It also means we don't need MII_BCM54XX_AUXCTL_SHDWSEL_MISC define as
it's the same as MII_BCM54XX_AUXCTL_SHDWSEL_MISC just for reading needs
(same value shifted by 12 bits).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
<linux/phy.h> includes <linux/phy_led_triggers.h>, which is not really
needed. Drop the include from <linux/phy.h>, and add it to all users
that didn't include it explicitly.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_attach_direct() ignores errors returned by
phy_led_triggers_register(). I think that's OK, as LED triggers can be
considered a non-critical feature.
However, this causes problems later:
- phy_led_trigger_change_speed() will access the array
phy_device.phy_led_triggers, which has been freed in the error path
of phy_led_triggers_register(), which may lead to a crash.
- phy_led_triggers_unregister() will access the same array, leading to
crashes during s2ram or poweroff, like:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
...
[<c04116d4>] (__list_del_entry_valid) from [<c05e8948>] (led_trigger_unregister+0x34/0xcc)
[<c05e8948>] (led_trigger_unregister) from [<c05336c4>] (phy_led_triggers_unregister+0x28/0x34)
[<c05336c4>] (phy_led_triggers_unregister) from [<c0531d44>] (phy_detach+0x30/0x74)
[<c0531d44>] (phy_detach) from [<c0538bdc>] (sh_eth_close+0x64/0x9c)
[<c0538bdc>] (sh_eth_close) from [<c04d4ce0>] (dpm_run_callback+0x48/0xc8)
or:
list_del corruption. prev->next should be dede6540, but was 2e323931
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:52!
...
[<c02f6d70>] (__list_del_entry_valid) from [<c0425168>] (led_trigger_unregister+0x34/0xcc)
[<c0425168>] (led_trigger_unregister) from [<c03a05a0>] (phy_led_triggers_unregister+0x28/0x34)
[<c03a05a0>] (phy_led_triggers_unregister) from [<c039ec04>] (phy_detach+0x30/0x74)
[<c039ec04>] (phy_detach) from [<c03a4fc0>] (sh_eth_close+0x6c/0xa4)
[<c03a4fc0>] (sh_eth_close) from [<c0483234>] (__dev_close_many+0xac/0xd0)
To fix this, clear phy_device.phy_num_led_triggers in the error path of
phy_led_triggers_register() fails.
Note that the "No phy led trigger registered for speed" message will
still be printed on link speed changes, which is a good cue that
something went wrong with the LED triggers.
Fixes: 2e0bc452f4 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One line was apparently pasted incorrectly during a new feature patch:
drivers/net/phy/marvell.c:2090:15: error: initialized field overwritten [-Werror=override-init]
.features = PHY_GBIT_FEATURES,
I'm removing the extraneous line here to avoid the W=1 warning and restore
the previous flags value, and I'm slightly reordering the lines for consistency
to make it less likely to happen again in the future. The ordering in the
array is still not the same as in the structure definition, instead I picked
the order that is most common in this file and that seems to make more sense
here.
Fixes: 0b04680fda ("phy: marvell: Add support for temperature sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_error() is called in the PHY state machine workqueue context, and
calls phy_trigger_machine() which does a cancel_delayed_work_sync() of
the workqueue we execute from, causing a deadlock situation.
Augment phy_trigger_machine() machine with a sync boolean indicating
whether we should use cancel_*_sync() or just cancel_*_work().
Fixes: 3c293f4e08 ("net: phy: Trigger state machine on state change and not polling.")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the HW design team recommended workaround in for 7278. Since
the GPHY now returns its revision information in MII_PHYS_ID[23] we need
to check whether the revision provided in flags is 0 or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BCM7278 28nm process Gigabit Ethernet PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell PHYs have an inbuilt temperature sensor. Add hwmon
support for this sensor.
There are two different variants. The simpler, older chips have a 5
degree accuracy. The newer devices have 1 degree accuracy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a1cba5613e ("net: phy: Add Broadcom phy library for common
interfaces") make the BCM63xx PHY driver utilize bcm_phy_config_intr()
which would appear to do the right thing, except that it does not write
to the MII_BCM63XX_IR register but to MII_BCM54XX_ECR which is
different.
This would be causing invalid link parameters and events from being
generated by the PHY interrupt.
Fixes: a1cba5613e ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This PHY with fiber support is register compatible with DP83848,
so add support for it.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dp83867 driver returns error if phy interface type
PHY_INTERFACE_MODE_RGMII_RXID is used to set the rx only internal
delay. Similarly issue happens for PHY_INTERFACE_MODE_RGMII_TXID.
Fix this by checking also the interface type if a particular delay
value is missing in the phy dt bindings. Also update the DT document
accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gpiod functions support handling low-active pins, so we can move
thos code out of this driver into the gpio subsystem and simplify
the code a bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using gpiod functions lets us use functionality which is not available
with gpio functions.
There is no gpiod function to match devm_gpio_request_one, so leave it
in place and use gpio_to_desc() to convert absolute pin numbers to gpio
descriptors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using devm_gpio_request_one lets us request gpio pins with initial state
in one go.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an Marvell 88E1512 PHY is connected to a nic in SGMII mode, the
fiber page is used for the SGMII host-side connection. The PHY driver
notices that SUPPORTED_FIBRE is set, so it tries reading the fiber page
for the link status, and ends up reading the MAC-side status instead of
the outgoing (copper) link. This leads to incorrect results reported
via ethtool.
If the PHY is connected via SGMII to the host, ignore the fiber page.
However, continue to allow the existing power management code to
suspend and resume the fiber page.
Fixes: 6cfb3bcc06 ("Marvell phy: check link status in case of fiber link.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As I understand it the Meson GXL PHY driver is only useful on one
architecture so only make it visible on that architecture.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 7334b3e47a ("net: phy: Add Meson GXL Internal PHY driver")
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().
If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.
This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.
This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan
Florian Fainelli
Andrew Lunn
Blomme, Maarten
David S. Miller
Yendapally Reddy Dhananjaya Reddy
Raju Lakkaraju
Lukasz Majewski
Mao Wenan
Arnd Bergmann
Rafał Miłecki
Sean Nyekjaer
Geert Uytterhoeven
Jingju Hou
Daniel Gonzalez Cabanelas
Alvaro G. M
Karicheri, Muralidharan
Guenter Roeck
Russell King
Jean Delvare
Zefir Kurtisi