The core st-nci module is useless without either the I2C or the
SPI access module. So hide NFC_ST_NCI and select it automatically
if either NFC_ST_NCI_I2C or NFC_ST_NCI_SPI is selected.
This avoids presenting NFC_ST_NCI when neither NFC_ST_NCI_I2C nor
NFC_ST_NCI_SPI can be selected.
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for acpi probing.
SMO2101 is used for st21nfcb
SMO2102 is used for st21nfcc
It has been tested with the following acpi node on Minnowboard:
Note: Remove uicc-present or ese-present Package if one them is not
supported.
Device (NFC1)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "SMO2101") // _HID: Hardware ID
Name (_CID, "SMO2101") // _CID: Compatible ID
Name (_DDN, "SMO NFC") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Name (_DSD, Package (0x02)
{
/* Device Properties for _DSD */
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package (0x02)
{
Package (0x02) { "uicc-present", 1 },
Package (0x02) { "ese-present", 1 }
}
})
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (SBUF, ResourceTemplate ()
{
I2cSerialBus (0x0008, ControllerInitiated, 400000,
AddressingMode7Bit, "\\_SB.I2C7",
0x00, ResourceConsumer, ,)
GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0001
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0002,
}
})
Return (SBUF) /* \_SB_.I2C7.NFC1._CRS.SBUF */
}
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add macro definition for each gpio string for an easier code
maintenance.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Group device table at the same place in order to make the code
easier to read and parse.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
DT headers already define NOOP routines when CONFIG_OF is not
defined.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove SPI_DUMP_SKB and I2C_DUMP_SKB as skb is already dumped
in ndlc layer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Upon some conditions (timing, CLF errors, platform errors...), the
irq might be already active when powering the device.
Add irq_active variable as a guard to avoid kernel warning message
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A secure element can be activated in different order.
The host_list is updated keeping a fixed order:
<terminal_host_id><uicc_id><ese_id>.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
After internal discussion, it appears this timing should be
increased to 20 ms for interoperability reason.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to align with st21nfca, dts configuration properties
ese_present and uicc_present are made available in st-nci driver.
So far, in early development firmware, because
nci_nfcee_mode_set(DISABLE) was not supported we had to try to
enable it during the secure element discovery phase.
After several trials on commercial and qualified firmware it appears
that nci_nfcee_mode_set(ENABLE) and nci_nfcee_mode_set(DISABLE) are
properly supported.
Such feature also help us to eventually save some time (~5ms) when
only one secure element is connected.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Potentially an unexpected HCI event may occur because of a
firmware bug. It could be transparent for the user but we need to
at least log it.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for proprietary commands useful mainly for
factory testings. Here is a list:
- FACTORY_MODE: Allow to set the driver into a mode where
no secure element are activated. It does not consider any
NFC_ATTR_VENDOR_DATA.
- HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes
command. It does not consider any NFC_ATTR_VENDOR_DATA.
- HCI_DM_PUT_DATA: Allow to configure specific CLF registry
like for example RF trimmings or low level drivers
configurations (I2C, SPI, SWP).
- HCI_DM_UPDATE_AID: Allow to configure an AID routing into the
CLF routing table following RF technology, CLF mode or protocol.
- HCI_DM_GET_INFO: Allow to retrieve CLF information.
- HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as
low level drivers configurations or RF trimmings.
- HCI_DM_DIRECT_LOAD: Allow to load a firmware into the CLF.
A complete packet can be more than 8KB.
- HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF
configuration changes without CLF power off.
- HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example
the white list).
- HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF
technology. When using this command to anti-collision is done.
- HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF
connectivity.
- HCI_DM_VDC_MEASUREMENT_VALUE: Allow to measure the field applied
on the CLF antenna. A value between 0 and 0x0f is returned. 0 is
maximum.
- HCI_DM_FWUPD_START: Allow to put CLF into firmware update mode.
It is a specific CLF command as there is no GPIO for this.
- HCI_DM_FWUPD_END: Allow to complete firmware update.
- HCI_DM_VDC_VALUE_COMPARISON: Allow to compare the field applied
on the CLF antenna to a reference value.
- MANUFACTURER_SPECIFIC: Allow to retrieve manufacturer specific data
received during a NCI_CORE_INIT_CMD.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST_NCI_DM_GETINFO(ST_NCI_DM_GETINFO_PIPE_LIST).
The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI_HCI_IDENTITY_MGMT_GATE might be useful to get information
about hardware or firmware version.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When initializing ndev->hci_dev->init_data, only gates field
was set. gate_count needs to be initialized as well.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We need to keep initial st_nci_gates values in order for
nci_hci_dev_connect_gates to create and open pipe when necessary.
For example after a firmware update CLF pipes are cleared. Changing
pipe values in st_nci_gates was causing nci_hci_dev_connect_gates
not using accurate pipes value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI_HCI_LINK_MGMT_PIPE was never opened in st_nci_hci_load_session.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When sending data over SPI, the maximum expected length is the maximum
nci packet payload + data header size + the frame head room (1 for the
ndlc header) + the frame trail room (0).
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Initially it was used to create hooks in the driver for
proprietary operations. Currently it is being used for hooks
for both proprietary and generic operations.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
spi phy needs to use ndlc_recv at every spi transaction causing
"unknown packet control byte" error message each time the header
is 00. Make this silent.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
st21nfcb does support another phy than i2c: spi.
st21nfcc does not support spi as the spi ios are used
by the AMS RF booster.
st21nfcb is not following NCI NFC Forum recommendations for spi
but rely on ST prioritary protocol ndlc as for i2c.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PCB_SYNC different than PCB_TYPE_SUPERVISOR or PCB_TYPE_DATAFRAME
should be discarded.
Irrelevant data may be forwarded up to the ndlc state machine by
phys like spi to prevent missing potential data during "write"
transactions.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When receiving a NDLC PCB_SYNC_ACK the pending data was never
removed from ack_pending_q and cleared.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
st_nci_hci_load_session() calls kfree_skb() on unitialized
variables skb_pipe_info and skb_pipe_list if the call to
nci_hci_connect_gate() failed. Reword the error path to not use
these variables when they are not initialized. While at it, there
seemed to be a memory leak because skb_pipe_info was only freed
once, after the for-loop, even though several ones were created
by nci_hci_send_cmd.
Cc: stable@vger.kernel.org
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to a copy and paste error st_nci_i2c_read still contains
st21nfca header comment.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace ST21NFCB with ST_NCI or st21nfcb with st_nci as it
was forgotten in commit "nfc: st-nci: Rename st21nfcb to st-nci"
ed06aeefda
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMicroelectronics NFC NCI chips family is extending
with the new ST21NFCC using the AMS AS39230 RF booster.
The st21nfcb driver is relevant for this solution and
might be with future products.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard
Linus Torvalds
Andrew F. Davis
Christophe Ricard
Robert Dolca
Samuel Ortiz