Add SDHC DMA channel description to the mpc512x device tree to enable
slave channel requesting in the mxcmmc driver.
mpc512x DMA engine doesn't support endianness conversion when
reading/writing data from peripheral's FIFO, so we have to swap data
buffers before each DMA write and after each DMA read transfer manually.
Since chained SDHC DMA transfers are not supported on mpc512x, limit
'max_segs' tunable parameter to one and initialise it to 64 only when
running on i.MX platforms.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
slot-gpio API suppors read-only detection when "wp-gpios"
property is present in the device tree mmc node. Use this
API for write-protect detection.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDHC controller on mpc512x is compatible with i.MX31 SDHC,
so the mxcmmc driver can be used on mpc512x, too. Extend the
driver to support mpc512x as well.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
mxcmci_dma_callback() is invoked by DMA drivers in soft-irq
context and can be interrupted by the mxcmci_irq() interrupt
which can finish the mmc request or data transfer and set
host->req or host->data pointers to NULL. Then mxcmci_data_done()
crashes with a null pointer dereferences. Protect all accesses
to host->req and host->data by spin locks.
Also check host->data pointer in mxcmci_watchdog() before
dereferencing it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adding devicetree support for imx21-mmc and imx31-mmc. Based on generic
gpio helper functions by Guennadi and generic DMA devicetree bindings.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes bug when card is present during boot.
Bug was introduced due commit "mmc: mxcmmc: fix bug that may block a
data transfer forever". When a card is present "mxcmci_setup_data"
function is executed, but the timer is not initialized.
...
i.MX SDHC driver
mmc0: SD Status: Invalid Allocation Unit size.
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 1.91 GiB
------------[ cut here ]------------
kernel BUG at kernel/timer.c:729!
Internal error: Oops - BUG: 0 [#1] PREEMPT ARM
CPU: 0 Not tainted (3.9.0-rc5-next-20130404 #2)
PC is at mod_timer+0x168/0x198
LR is at mxcmci_request+0x21c/0x328
...
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to be
part of the multiplatform support -- the first "big" SoC that is moved
over (more multiplatform work comes in a separate branch later during
the merge window).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zfPd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
When a SD card is initialized some data transfers of 64 and 8 bytes
are issued. It seems the DMA has some problems dealing with these kind
of "short" transfers, leading sometimes to the SD card not being detected.
In order to solve this problem, do not use DMA for transfer sizes lower
than the sector size.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The correct name for the driver is "mxc-mmc".
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chris Ball <cjb@laptop.org>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: linux-mmc@vger.kernel.org
Core:
- Add DT properties for card detection (broken-cd, cd-gpios, non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't already
have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qyY5
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"Core:
- Add DT properties for card detection (broken-cd, cd-gpios,
non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't
already have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree
support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of
presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)"
* tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (67 commits)
mmc: core: Fixup broken suspend and eMMC4.5 power off notify
mmc: sdhci-spear: Add clk_{un}prepare() support
mmc: sdhci-spear: add device tree bindings
mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resume
mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator
mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirks
mmc: dt: Support "broken-cd" property in sdhci-pltfm
mmc: sdhci-s3c: fix the wrong number of max bus clocks
mmc: sh-mmcif: avoid oops on spurious interrupts
mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQ
mmc: sdhci-s3c: Fix crash on module insertion for second time
mmc: sdhci-s3c: Enable only required bus clock
mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration"
mmc: mxcmmc: fix bug that may block a data transfer forever
mmc: omap_hsmmc: Pass on the suspend failure to the PM core
mmc: atmel-mci: AP700x PDC is not connected to MCI
mmc: atmel-mci: DMA can be used with other controllers
mmc: mmci: use clk_prepare_enable and clk_disable_unprepare
mmc: sdhci-s3c: Add device tree support
mmc: dw_mmc: add support for exynos specific implementation of dw-mshc
...
The problem can be easily reproduced using a script that loops
copying a file in an SD card to another place in the same SD card
and its related to read transfers. This only happens with DMA enabled.
This is related to the fact that, when reading, an MMC irq signals
the fact that all data from the SD card has been copied to the
internal buffers. However, it doesn't signal whether the DMA transfer
that is in charge of moving data from these internal buffers to RAM
has finished or not. Thus, calling dmaengine_terminate_all() in the
MMC irq routine can cancel an ongoing DMA transfer leaving some data
in the internal buffers that produces an accumulative effect which,
in the end, blocks a read data transfer forever.
The following patch watches DMA irq for reading and MMC irqs for
writing transfers. The 'dangerous' usage of dmaengine_terminate_all()
is removed and a timeout of 10 seconds is added so that the MMC won't
block forever anymore.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
.device_fc is added in struct dma_slave_config recently. All user drivers, which
want DMA to be the flow controller must pass this field as false. As earlier
driver don't look to use this feature, mark it false for now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch converts the drivers in drivers/mmc/host/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When we can't configure the dma channel we want to fall
back to PIO. We do this by setting host->do_dma to zero.
This does not work as do_dma is used to see whether dma
can be used for the current transfer. Instead, we have
to set host->dma to NULL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves mmc drivers to use new enum
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When indirect inclusion to <mach/hardware.h> via <mach/gpio.h> gets
removed, we will see the following compile error.
CC drivers/mmc/host/mxcmmc.o
drivers/mmc/host/mxcmmc.c: In function ‘mxcmci_init_card’:
drivers/mmc/host/mxcmmc.c:811:2: error: implicit declaration of function ‘cpu_is_mx3’
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
dmaengine expects the maxburst parameter in words, not bytes.
The imxdma driver and its users do this wrong. Fix this.
As a side note the imx-pcm-dma-mx2 driver was 'fixed' to work
with imx-dma. This broke the driver with imx-sdma support which
correctly takes the maxburst parameter in words. This patch
puts the sdma based sound back to work.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the mxcmmc driver to use the dmaengine API. Unlike
the old one this one is always present in the tree, even if no DMA
is implemented, hence we can remove all the #ifdefs in from the driver.
The driver automatically switches to PIO mode if no DMA support or no
suitable channel is available.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove release_resource() after release_mem_region().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This also fixes the build problem introduced by my previous patch
due to unhandled API changes introduced by commit:
99fc513101 (mmc: Move regulator handling closer to core)
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This implementation is based on the pxamci.c driver and it will
be used to support the mx31_3ds machine.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have deprecated the distinction between hardware and physical
segments in the block layer. Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
Even though many mmc host drivers pass a pm_message_t argument to
mmc_suspend_host() that argument isn't used the by MMC core. As host
drivers are converted to dev_pm_ops they'll have to construct
pm_message_t's (as they won't be passed by the PM subsystem any more) just
to appease the mmc suspend interface.
We might as well just delete the unused paramter.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>ZZ
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From cefcdab08d1c9636c4a7290bc2bbe937d051bce4 Mon Sep 17 00:00:00 2001
From: Volker Ernst <volker.ernst@txtr.com>
Date: Mon, 26 Apr 2010 22:51:07 +0200
Subject: [PATCH] ARM: mx3: Fix a race condition in mxcmmc
This fixes a race condition regarding interrupt bits in the SDHC
controller driver code.
In case of PIO-transfer it does not clear SDHC-status bit#11/12
in the INT-handler anymore. INT-handler might be called during
an ongoing PIO-data-transfer (with some other INT-flag set) and
PIO-transfer depends on these bits being set to detect the end
of the data-transfer. This also means that at the end of PIO-
transfer that PIO-software has to clear these bits itself.
However in case of DMA-transfer these bits have to be cleared
in the INT-handler, because they are used to generate INTs then.
Works solid, no more problems here, can transfer big files.
Signed-off-by: Volker Ernst <volker.ernst@txtr.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Cc: Andy Green <andy@warmcat.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MX3 SoCs have a silicon bug which corrupts CRC calculation of
multi-block transfers when connected SDIO peripheral doesn't drive the
BUSY line as required by the specs.
One way to prevent this is to only allow 1-bit transfers.
Another way is playing tricks with the DMA engine, but this isn't
mainline yet. So for now, we live with the performance drawback of 1-bit
transfers until a nicer solution is found.
This patch introduces a new host controller callback 'init_card' which
is for now only called from mmc_sdio_init_card().
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Be more verbose on error messages and add one debug message.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
This unpleasant typo appeared while porting the driver from Freescale
original sources, where anyone can easily find the correct version.
Current incorrect version potentially can influence segment and merge
handling in block subsystem via MMC request queue settings.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After a failing allocation of mmc or a failed ioremap in mxcmci_probe host was
used uninitialized.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MMC core has now been fixed to not send silly frequencies to the
drivers which means we can remove this workaround.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
When a software timeout occurs in polling mode hardware was left in
an indeterminate state causing subsequent operations to block.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
This is a temporary workaround until the MMC stack can be fixed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>