The R_INTC in the A31 and newer sun8i/sun50i SoCs is more similar to the
original sun4i interrupt controller than the sun7i/sun9i NMI controller.
It is used for two distinct purposes:
- To control the trigger, latch, and mask for the NMI input pin
- To provide the interrupt input for the ARISC coprocessor
As this interrupt controller is not documented, information about it
comes from vendor-provided firmware blobs and from experimentation.
Differences from the sun4i interrupt controller appear to be:
- It only has one or two registers of each kind (max 32 or 64 IRQs)
- Multiplexing logic is added to support additional inputs
- There is no FIQ-related logic
- There is no interrupt priority logic
In order to fulfill its two purposes, this hardware block combines four
types of IRQs. First, the NMI pin is routed to the "IRQ 0" input on this
chip, with a trigger type controlled by the NMI_CTRL_REG. The "IRQ 0
pending" output from this chip, if enabled, is then routed to a SPI IRQ
input on the GIC. In other words, bit 0 of IRQ_ENABLE_REG *does* affect
the NMI IRQ seen at the GIC.
The NMI is followed by a contiguous block of 15 "direct" (my name for
them) IRQ inputs that are connected in parallel to both R_INTC and the
GIC. Or in other words, these bits of IRQ_ENABLE_REG *do not* affect the
IRQs seen at the GIC.
Following the direct IRQs are the ARISC's copy of banked IRQs for shared
peripherals. These are not relevant to Linux. The remaining IRQs are
connected to a multiplexer and provide access to the first (up to) 128
SPIs from the ARISC. This range of SPIs overlaps with the direct IRQs.
Because of the 1:1 correspondence between R_INTC and GIC inputs, this is
a perfect scenario for using a stacked irqchip driver. We want to hook
into setting the NMI trigger type, but not actually handle any IRQ here.
To allow access to all multiplexed IRQs, this driver requires a new
binding where the interrupt number matches the GIC interrupt number.
(This moves the NMI from number 0 to 32 or 96, depending on the SoC.)
For simplicity, copy the three-cell GIC binding; this disambiguates
interrupt 0 in the old binding (the NMI) from interrupt 0 in the new
binding (SPI 0) by the number of cells.
Since R_INTC is in the always-on power domain, and its output is visible
to the power management coprocessor, a stacked irqchip driver provides a
simple way to add wakeup support to any of its IRQs. That is the next
patch; for now, just the NMI is moved over.
This commit mostly reverts commit 173bda53b3 ("irqchip/sunxi-nmi:
Support sun6i-a31-r-intc compatible").
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210118055040.21910-4-samuel@sholland.org
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add option for Allwinner ARMv5 SoCs and SoC F1C100s (which has a die
used for many new F-series products, including F1C100A, F1C100s, F1C200s,
F1C500, F1C600).
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner also has some ARMv5 SoCs.
In order to add support for them, check ARM_MULTI_V7 before enabling
ARMv7 SoC's. Add help text for ARCH_SUNXI menuconfig.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the support for A83T.
A83T SoC has an additional register than A80 to handle CPU configurations:
R_CPUS_CFG. Information about the register comes from Allwinner's BSP
driver.
An important difference is the Power Off Gating register for clusters
which is BIT(4) in case of SUN9I-A80 and BIT(0) in case of SUN8I-A83T.
There is also a bit swap between sun8i-a83t and sun9i-a80 that must be
handled.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 is a big.LITTLE SoC with 1 cluster of 4 Cortex-A7s and
1 cluster of 4 Cortex-A15s.
This patch adds support to bring up the second cluster and thus all
cores using custom platform SMP code. Core/cluster power down has not
been implemented, thus CPU hotplugging is not supported.
Parts of the trampoline and re-entry code for the boot cpu was adapted
from the MCPM framework.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Device frequency scaling is implemented through devfreq in the kernel,
which requires CONFIG_PM_OPP.
Let's select it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With previous fixes to stmmac, sun4i-emac and sun4i-mmc at least the
Cubieboard2 incarnation of sunxi works correctly in big-endian mode.
Allow the selection of big-endian.
Tested using a Cubieboard2 DualCard and the following
hardware-components:
- GMAC (stmmac)
- EMAC (sun4i-emac)
- SATA
- SPI
- UART
- security system
- touchscreen controller hwmon functionality
- pinctrl (custom interrupt for SPI ethernet controller)
- watchdog as reset controller
- onboard RTC
- DS1307 I2C RTC
- sound codec and with this indirectly the DMA engine
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This replaces:
- "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB" as this can
now be selected directly.
- "select ARCH_WANT_OPTIONAL_GPIOLIB" with no dependency: GPIOLIB
is now selectable by everyone, so we need not declare our
intent to select it.
When ordering the symbols the following rationale was used:
if the selects were in alphabetical order, I moved select GPIOLIB
to be in alphabetical order, but if the selects were not
maintained in alphabetical order, I just replaced
"select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB".
Cc: Michael Büsch <m@bues.ch>
Cc: arm@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Many ARM sub-architectures use prompts followed by "if" conditional,
but it is wrong.
Please notice the difference between
config ARCH_FOO
bool "Foo SoCs" if ARCH_MULTI_V7
and
config ARCH_FOO
bool "Foo SoCs"
depends on ARCH_MULTI_V7
These two are *not* equivalent!
In the former statement, it is not ARCH_FOO, but its prompt that
depends on ARCH_MULTI_V7. So, it is completely valid that ARCH_FOO
is selected by another, but ARCH_MULTI_V7 is still disabled. As it is
not unmet dependency, Kconfig never warns. This is probably not what
you want.
The former should be used only when you need to do so, and you really
understand what you are doing. (In most cases, it should be wrong!)
For enabling/disabling sub-architectures, the latter is always correct.
As a good side effect, this commit fixes some entries over 80 columns
(mach-imx, mach-integrator, mach-mbevu).
[Arnd: I note that there is not really a bug here, according to
the discussion that followed, but I can see value in being consistent
and in making the lines shorter]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Halasa <khc@piap.pl>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
to other sun8i family SoCs like the A23.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As the sunxi usb clocks all contain a reset controller, it is not
possible to build the sunxi clock driver without RESET_CONTROLLER
enabled. Doing so results in an undefined symbol error:
drivers/built-in.o: In function `sunxi_gates_clk_setup':
linux/drivers/clk/sunxi/clk-sunxi.c:1071: undefined reference to
`reset_controller_register'
This is possible if building a minimal kernel without PHY_SUN4I_USB.
The dependency issue is made visible at compile time instead of
link time by the new A80 mmc clocks, which also use a reset control
itself.
This patch makes ARCH_SUNXI select ARCH_HAS_RESET_CONTROLLER and
RESET_CONTROLLER.
Fixes: 559482d1f9 ARM: sunxi: Split the various SoCs support in Kconfig
Cc: <stable@vger.kernel.org> # 3.16+
Reported-by: Lourens Rozema <ik@lourensrozema.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 SoC has reset controls matching bus clock gates.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A80 is a new Cortex octo-core A7/A15 big.LITTLE SoC.
While it's processor cores and interconnecting bus are new, it
re-uses many peripherals found in earlier Allwinner SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
The PINCTRL_SUNXI configuration was kept only to deal with the introduction of
per-machine symbols and the various pintrl drivers through different tree.
Now that it's not useful anymore, we can just remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Select the MFD_SUN6I_PRCM option when sun8i arch is enabled in order to
get the PRCM (Power/Reset/Clock Management) related drivers compiled.
Also select ARCH_HAS_RESET_CONTROLLER and RESET_CONTROLLER to make sure
the reset controller drivers are compiled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A23 is a dual-core Cortex-A7-based SoC. It re-uses most of
the IPs found in previous SoCs, notably the A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Select the MFD_SUN6I_PRCM option when sun6i arch is enabled in order to get
the PRCM (Power/Reset/Clock Management) related drivers compiled.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This will allow to better isolate various options, and reduce the overall
kernel size if we're interested in only one of the SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order for the architected timers support to be enabled in the kernel, this
option has to be enabled. Otherwise, the architected timers driver won't be
compiled in, and we will not get to use them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
All V7 platforms can run SMP kernels, so make CONFIG_SMP visible for V7
multi-platform builds.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Multi-platform requires various kconfig options to be selected, so
platforms don't need to select them individually.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with some
random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m, i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pgLW
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with
some random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m,
i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in
industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits)
ARM: tegra: fix tegra_powergate_sequence_power_up() inline
ARM: msm_defconfig: Update for multi-platform
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
ARM: shmobile: r8a7790: Fix I2C controller names
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
...
On Allwinner sun7i (A20) SoCs, the SMP operations are implemented in
u-boot, and exposed to the kernel through PSCI.
We thus need to enable PSCI support for Allwinner SoCs so that the
kernel uses it to bring up the additionnal cores.
Signed-off-by: Signed-off-by: Zalan Blenessy <zalan.blenessy@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current code selects ARCH_HAS_RESET_CONTROLLER, that enables the
RESET_CONTROLLER option by default, but doesn't select it, so a configuration
might unselect it, leading to compilation error.
Explictly select RESET_CONTROLLER so that we can't have this breakage anymore.
Reported-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the Allwinner SoCs (at this time, all but the A10) also have a
High Speed timers that are not using the 24MHz oscillator as a source
but rather the AHB clock running much faster.
The IP is slightly different between the A10s/A13 and the one used in
the A20/A31, since the latter have 4 timers available, while the former
have only 2 of them.
[dlezcano] : Fixed conflict with b788beda "Order Kconfig options
alphabetically"
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The A31 has a reset controller, and we have to select this option to
have access to the reset controller framework.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
The Allwinner A31 is a quad-Cortex-A7 based SoC, which shares a lot of
IPs with the previous SoCs from Allwinner, like the PIO, I2C, UARTs,
timers, watchdog IPs, but also differs by dropping the WEMAC ethernet
controller and most notably dropping the in-house IRQ controller in
favor of a ARM GIC one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
CONFIG_ARCH_SUNXI currently doesn't enable a gpiolib, which causes build
problems when building a kernel with only the sunxi platform enabled.
Select ARCH_REQUIRE_GPIOLIB to solve this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
During the introduction of the Allwinner SoC platforms, sunxi was
initially meant as a generic name for all the variants of the Allwinner
SoC.
It was ok at the time of the support of only the A10 and A13 that
looks pretty much the same, but it's beginning to be troublesome with
the future addition of the Allwinner A31 (sun6i) that is quite
different, and would introduce some weird logic, where sunxi would
actually mean in some case sun4i and sun5i but without sun6i...
Moreover, it makes the compatible strings naming scheme not consistent
with other architectures, where usually for this kind of compability, we
just use the oldest SoC name that has this IP, so let's do just this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Using CLKSRC_OF allows to remove the SoC specific sunxi_timer.h header,
and instead of using a custom init function in the machine definition
use the standard clocksource_of_init function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner SoCs have an IP module that handle both the muxing and the
GPIOs.
This IP has 8 banks of 32 bits, with a number of pins actually useful
for each of these banks varying from one to another, and depending on
the SoC used on the board.
This driver only implements the pinctrl part, the gpio part will come
eventually.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Samuel Holland
Thomas Gleixner
Mesih Kilinc
Mylène Josserand
Chen-Yu Tsai
Maxime Ripard
Michael Weiser
Linus Walleij
Masahiro Yamada
Jens Kuske
Linus Torvalds
Boris BREZILLON
Rob Herring
Zalan Blenessy