This makes the late e820 resources use 'insert_resource_expand_to_fit()'
instead of doing a 'reserve_region_with_split()', and also avoids
marking them as IORESOURCE_BUSY.
This results in us being perfectly happy to use pre-existing PCI
resources even if they were marked as being in a reserved region, while
still avoiding any _new_ allocations in the reserved regions. It also
makes for a simpler and more accurate resource tree.
Example resource allocation from Jonathan Corbet, who has firmware that
has an e820 reserved entry that covered a big range (e0000000-fed003ff),
and that had various PCI resources in it set up by firmware.
With old kernels, the reserved range would force us to re-allocate all
pre-existing PCI resources, and his reserved range would end up looking
like this:
e0000000-fed003ff : reserved
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
where only the pre-allocated special regions (IOAPIC and HPET) were kept
around.
With 2.6.28-rc2, which uses 'reserve_region_with_split()', Jonathan's
resource tree looked like this:
e0000000-fe7fffff : reserved
fe800000-fe8fffff : PCI Bus 0000:01
fe800000-fe8fffff : reserved
fe900000-fe9d9aff : reserved
fe9d9b00-fe9d9bff : 0000:00:1f.3
fe9d9b00-fe9d9bff : reserved
fe9d9c00-fe9d9fff : 0000:00:1a.7
fe9d9c00-fe9d9fff : reserved
fe9da000-fe9dafff : 0000:00:03.3
fe9da000-fe9dafff : reserved
fe9db000-fe9dbfff : 0000:00:19.0
fe9db000-fe9dbfff : reserved
fe9dc000-fe9dffff : 0000:00:1b.0
fe9dc000-fe9dffff : reserved
fe9e0000-fe9fffff : 0000:00:19.0
fe9e0000-fe9fffff : reserved
fea00000-fea7ffff : 0000:00:02.0
fea00000-fea7ffff : reserved
fea80000-feafffff : 0000:00:02.1
fea80000-feafffff : reserved
feb00000-febfffff : 0000:00:02.0
feb00000-febfffff : reserved
fec00000-fed003ff : reserved
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
and because the reserved entry had been split and moved into the
individual resources, and because it used the IORESOURCE_BUSY flag, the
drivers that actually wanted to _use_ those resources couldn't actually
attach to them:
e1000e 0000:00:19.0: BAR 0: can't reserve mem region [0xfe9e0000-0xfe9fffff]
HDA Intel 0000:00:1b.0: BAR 0: can't reserve mem region [0xfe9dc000-0xfe9dffff]
with this patch, the resource tree instead becomes
e0000000-fed003ff : reserved
fe800000-fe8fffff : PCI Bus 0000:01
fe9d9b00-fe9d9bff : 0000:00:1f.3
fe9d9c00-fe9d9fff : 0000:00:1a.7
fe9d9c00-fe9d9fff : ehci_hcd
fe9da000-fe9dafff : 0000:00:03.3
fe9db000-fe9dbfff : 0000:00:19.0
fe9db000-fe9dbfff : e1000e
fe9dc000-fe9dffff : 0000:00:1b.0
fe9dc000-fe9dffff : ICH HD audio
fe9e0000-fe9fffff : 0000:00:19.0
fe9e0000-fe9fffff : e1000e
fea00000-fea7ffff : 0000:00:02.0
fea80000-feafffff : 0000:00:02.1
feb00000-febfffff : 0000:00:02.0
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
ie the one reserved region now ends up surrounding all the PCI resources
that were allocated inside of it by firmware, and because it is not
marked BUSY, drivers have no problem attaching to the pre-allocated
resources.
Reported-and-tested-by: Jonathan Corbet <corbet@lwn.net>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the links to architecture and machine dependent directories
(boot, lib, drivers, arch, mach)
The links were created and used mostly from the arch/cris/Makefile,
so why not dispense with them altogether?
Changed $(ARCH) to "cris" in Makefile, it is easier to read this way.
The CRISv32 head.S common files for the kernel and compressed images
needed to be modified to use ifdefs instead of using the now removed
mach link. Since there are only two versions, this is not a huge loss
in readability.
The link to vmlinux.lds.S is also replaced with a merged version
which uses ifdefs to select the correct layout.
System.map before and after are identical.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Eliminates the link to arch specific asm-offsets.c from CRIS
architecture build system.
Resulting asm-offsets.s are identical before and after change
for both arch-v10 and arch-v32.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
Revert "powerpc: Sync RPA note in zImage with kernel's RPA note"
powerpc: Fix compile errors with CONFIG_BUG=n
powerpc: Fix format string warning in arch/powerpc/boot/main.c
powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()
powerpc: Remove duplicate DMA entry from mpc8313erdb device tree
powerpc/cell/OProfile: Fix on-stack array size in activate spu profiling function
powerpc/mpic: Fix regression caused by change of default IRQ affinity
powerpc: Update remaining dma_mapping_ops to use map/unmap_page
powerpc/pci: Fix unmapping of IO space on 64-bit
powerpc/pci: Properly allocate bus resources for hotplug PHBs
OF-device: Don't overwrite numa_node in device registration
powerpc: Fix swapcontext system for VSX + old ucontext size
powerpc: Fix compiler warning for the relocatable kernel
powerpc: Work around ld bug in older binutils
powerpc/ppc64/kdump: Better flag for running relocatable
powerpc: Use is_kdump_kernel()
powerpc: Kexec exit should not use magic numbers
powerpc/44x: Update 44x defconfigs
powerpc/40x: Update 40x defconfigs
powerpc: enable heap randomization for linkstations
...
Updated the patch to address comments by Michael Ellerman.
Specifically, changed upper limit in for loop to
ARRAY_SIZE() macro and added a check to make sure the
number of events specified by the user, which is used as
the max for indexing various arrays, is no bigger then the
declared size of the arrays.
The size of the pm_signal_local array should be equal to the
number of SPUs being configured in the array. Currently, the
array is of size 4 (NR_PHYS_CTRS) but being indexed by a for
loop from 0 to 7 (NUM_SPUS_PER_NODE).
Signed-off-by: Carl Love <carll@us.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (21 commits)
sh: fix sh2a cache entry_mask
sh: Enable NFS root in Migo-R defconfig.
sh: FTRACE renamed to FUNCTION_TRACER.
sh: Fix up the shared IRQ demuxer's control bit testing logic.
Define SCSPTR1 for SH 7751R
sh: Add sci_rxd_in of SH4-202
Add support usb setting on sh 7366
sh: Change register name SCSPTR to SCSPTR2
sh: use the new byteorder headers.
sh: SHmedia ISA tuning fixups.
sh: Kill off long-dead HD64465 cchip support.
sh: Revert "SH 7366 needs SCIF_ONLY"
sh: Simplify and lock down the ISA tuning.
sh: sh7785lcr: Select uImage as default image target.
sh: Add on-chip RTC support for SH7722.
SH 7366 needs SCIF_ONLY
gdrom: Fix compile error
sh: Provide a sample defconfig for the UL2 (SH7366) board.
sh: Fix FPU tuning on toolchains with mismatched multilib targets.
sh: oprofile: Fix up the SH7750 performance counter name.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Add missing null terminating entry to bq4802_match[].
sparc: use the new byteorder headers
rtc-m48t59: shift zero year to 1968 on sparc (rev 2)
dbri: check dma_alloc_coherent errors
sparc64: remove byteshifting from out* helpers
This reverts commit 91a0030295, plus
commit 0dcd440120 ("powerpc: Revert CHRP
boot wrapper to real-base = 12MB on 32-bit") which depended on it.
Commit 91a00302 was causing NVRAM corruption on some pSeries machines,
for as-yet unknown reasons, so this reverts it until the cause is
identified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes sure we don't try to call find_bug or is_warning_bug when
CONFIG_BUG=n and CONFIG_XMON=y. Otherwise we get these errors:
arch/powerpc/xmon/xmon.c: In function ‘print_bug_trap’:
arch/powerpc/xmon/xmon.c:1364: error: implicit declaration of function ‘find_bug’
arch/powerpc/xmon/xmon.c:1364: warning: assignment makes pointer from integer without a cast
arch/powerpc/xmon/xmon.c:1367: error: implicit declaration of function ‘is_warning_bug’
arch/powerpc/xmon/xmon.c:1374: error: dereferencing pointer to incomplete type
make[2]: *** [arch/powerpc/xmon/xmon.o] Error 1
make[1]: *** [arch/powerpc/xmon] Error 2
make: *** [sub-make] Error 2
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix format string warning in arch/powerpc/boot/main.c. Also correct
a typo ("uncomressed") on the same line.
BOOTCC arch/powerpc/boot/main.o
arch/powerpc/boot/main.c: In function 'prep_kernel':
arch/powerpc/boot/main.c:65: warning: format '%08x' expects type
'unsigned int', but argument 3 has type 'long unsigned int'
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's currently an off-by-one bug in fdt_subnode_offset_namelen()
which causes it to keep searching after it's finished the subnodes of
the given parent, and into the subnodes of siblings of the original
node which come after it in the tree. This bug was introduced in
commit ed95d7450d ("powerpc: Update
in-kernel dtc and libfdt to version 1.2.0").
A patch has already been submitted to dtc/libfdt mainline. We don't
really want to pull in a new upstream version during the 2.6.28 cycle,
but we should still fix this bug, hence this standalone version of the
fix for the in-kernel libfdt.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Impact: introduce new APIs, separate kmap code from CONFIG_HIGHMEM
This takes the code used for CONFIG_HIGHMEM memory mappings except that
it's designed for dynamic IO resource mapping.
These fixmaps are available even with CONFIG_HIGHMEM turned off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix on certain UP configs
fix:
arch/x86/kernel/cpu/common.c: In function 'cpu_init':
arch/x86/kernel/cpu/common.c:1141: error: 'boot_cpu_id' undeclared (first use in this function)
arch/x86/kernel/cpu/common.c:1141: error: (Each undeclared identifier is reported only once
arch/x86/kernel/cpu/common.c:1141: error: for each function it appears in.)
Pull in asm/smp.h on UP, so that we get the definition of
boot_cpu_id.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch add usb setting for sh 7366
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-5 doesn't support any elaborate ISA inheritance schemes (-dsp, -up,
etc.), so only bother with that if we are building an sh32 kernel.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The size of the pm_signal_local array should be equal to the
number of SPUs being configured in the array. Currently, the
array is of size 4 (NR_PHYS_CTRS) but being indexed by a for
loop from 0 to 7 (NUM_SPUS_PER_NODE). This could potentially
cause an oops or random memory corruption since the pm_signal_local
array is on the stack. This fixes it.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Freescale implementation of MPIC only allows a single CPU destination
for non-IPI interrupts. We add a flag to the mpic_init to distinquish
these variants of MPIC. We pull in the irq_choose_cpu from sparc64 to
select a single CPU as the destination of the interrupt.
This is to deal with the fact that the default smp affinity was
changed by commit 1840475676 ("genirq:
Expose default irq affinity mask (take 3)") to be all CPUs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After the merge of the 32 and 64bit DMA code, dma_direct_ops lost
their map/unmap_single() functions but gained map/unmap_page(). This
caused a problem for Cell because Cell's dma_iommu_fixed_ops called
the dma_direct_ops if the fixed linear mapping was to be used or the
iommu ops if the dynamic window was to be used. So in order to fix
this problem we need to update the 64bit DMA code to use
map/unmap_page.
First, we update the generic IOMMU code so that iommu_map_single()
becomes iommu_map_page() and iommu_unmap_single() becomes
iommu_unmap_page(). Then we propagate these changes up through all
the callers of these two functions and in the process update all the
dma_mapping_ops so that they have map/unmap_page rahter than
map/unmap_single. We can do this because on 64bit there is no HIGHMEM
memory so map/unmap_page ends up performing exactly the same function
as map/unmap_single, just taking different arguments.
This has no affect on drivers because the dma_map_single_attrs() just
ends up calling the map_page() function of the appropriate
dma_mapping_ops and similarly the dma_unmap_single_attrs() calls
unmap_page().
This fixes an oops on Cell blades, which oops on boot without this
because they call dma_direct_ops.map_single, which is NULL.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A typo/thinko made us pass the wrong argument to __flush_hash_table_range
when unplugging bridges, thus not flushing all the translations for
the IO space on unplug. The third parameter to __flush_hash_table_range
is `end', not `size'.
This causes the hypervisor to refuse unplugging slots.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Resources for PHB's that are dynamically added to a system are not
properly allocated in the resource tree.
Not having these resources allocated causes an oops when removing
the PHB when we try to release them.
The diff appears a bit messy, this is mainly due to moving everything
one tab to the left in the pcibios_allocate_bus_resources routine.
The functionality change in this routine is only that the
list_for_each_entry() loop is pulled out and moved to the necessary
calling routine.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the numa_node of OF-devices will be overwritten during
device_register, which simply sets the node to -1. On cell machines,
this means that devices can't find their IOMMU, which is referenced
through the device's numa node.
Set the numa node for OF devices with no parent, and use the
lower-level device_initialize and device_add functions, so that the
node is preserved.
We can remove the call to set_dev_node in of_device_alloc, as it
will be overwritten during register.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since VSX support was added, we now have two sizes of ucontext_t;
the older, smaller size without the extra VSX state, and the new
larger size with the extra VSX state. A program using the
sys_swapcontext system call and supplying smaller ucontext_t
structures will currently get an EINVAL error if the task has
used VSX (e.g. because of calling library code that uses VSX) and
the old_ctx argument is non-NULL (i.e. the program is asking for
its current context to be saved). Thus the program will start
getting EINVAL errors on calls that previously worked.
This commit changes this behaviour so that we don't send an EINVAL in
this case. It will now return the smaller context but the VSX MSR bit
will always be cleared to indicate that the ucontext_t doesn't include
the extra VSX state, even if the task has executed VSX instructions.
Both 32 and 64 bit cases are updated.
[paulus@samba.org - also fix some access_ok() and get_user() calls]
Thanks to Ben Herrenschmidt for noticing this problem.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes this warning:
arch/powerpc/kernel/setup_64.c:447:5: warning: "kernstart_addr" is not defined
which arises because PHYSICAL_START is no longer a constant when
CONFIG_RELOCATABLE=y.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 549e8152de ("powerpc: Make the
64-bit kernel as a position-independent executable") added lines to
vmlinux.lds.S to add the extra sections needed to implement a
relocatable kernel. However, those lines seem to trigger a bug in
older versions of GNU ld (such as 2.16.1) when building a
non-relocatable kernel. Since ld 2.16.1 is still a popular choice for
cross-toolchains, this adds an #ifdef to vmlinux.lds.S so the added
lines are only included when building a relocatable kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The __kdump_flag ABI is overly constraining for future development.
As of 2.6.27, the kernel entry point has 4 constraints: Offset 0 is
the starting point for the master (boot) cpu (entered with r3 pointing
to the device tree structure), offset 0x60 is code for the slave cpus
(entered with r3 set to their device tree physical id), offset 0x20 is
used by the iseries hypervisor, and secondary cpus must be well behaved
when the first 256 bytes are copied to address 0.
Placing the __kdump_flag at 0x18 is bad because:
- It was taking the last 8 bytes before the iseries hypervisor data.
- It was 8 bytes for a boolean flag
- It had no way of identifying that the flag was present
- It does leave any room for the master to add any additional code
before branching, which hurts debug.
- It will be unnecessarily hard for 32 bit code to be common (8 bytes)
Now that we have eliminated the use of __kdump_flag in favor of
the standard is_kdump_kernel(), this flag only controls run without
relocating the kernel to PHYSICAL_START (0), so rename it __run_at_load.
Move the flag to 0x5c, 1 word before the secondary cpu entry point at
0x60. Initialize it with "run0" to say it will run at 0 unless it is
set to 1. It only exists if we are relocatable.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
linux/crash_dump.h defines is_kdump_kernel() to be used by code that
needs to know if the previous kernel crashed instead of a (clean) boot
or reboot.
This updates the just added powerpc code to use it. This is needed
for the next commit, which will remove __kdump_flag.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 54622f10a6 ("powerpc: Support for
relocatable kdump kernel") added a magic flag value in a register to
tell purgatory that it should be a panic kernel. This part is wrong
and is reverted by this commit.
The kernel gets a list of memory blocks and a entry point from user space.
Its job is to copy the blocks into place and then branch to the designated
entry point (after turning "off" the mmu).
The user space tool inserts a trampoline, called purgatory, that runs
before the user supplied code. Its job is to establish the entry
environment for the new kernel or other application based on the contents
of memory. The purgatory code is compiled and embedded in the tool,
where it is later patched using the elf symbol table using elf symbols.
Since the tool knows it is creating a purgatory that will run after a
kernel crash, it should just patch purgatory (or the kernel directly)
if something needs to happen.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: fix irq vectors.
lguest: fix early_ioremap.
lguest: fix example launcher compile after moved asm-x86 dir.
do_IRQ: cannot handle IRQ -1 vector 0x20 cpu 0
------------[ cut here ]------------
kernel BUG at arch/x86/kernel/irq_32.c:219!
We're not ISA: we have a 1:1 mapping from vectors to irqs.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
dmi_scan_machine breaks under lguest:
lguest: unhandled trap 14 at 0xc04edeae (0xffa00000)
This is because we use current_cr3 for the read_cr3() paravirt
function, and it isn't set until the first cr3 change. We got away
with it until this happened.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
fix:
arch/x86/kernel/cpu/common.c: In function 'early_identify_cpu':
arch/x86/kernel/cpu/common.c:553: error: 'struct cpuinfo_x86' has no member named 'cpu_index'
as cpu_index is only available on SMP.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix /proc/cpuinfo output on x86/Voyager
Ever since
| commit 92cb7612ae
| Author: Mike Travis <travis@sgi.com>
| Date: Fri Oct 19 20:35:04 2007 +0200
|
| x86: convert cpuinfo_x86 array to a per_cpu array
We've had an extra field in cpuinfo_x86 which is cpu_index.
Unfortunately, voyager has never initialised this, although the only
noticeable impact seems to be that /proc/cpuinfo shows all zeros for
the processor ids.
Anyway, fix this by initialising the boot CPU properly and setting the
index when the secondaries update.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix on x86/Voyager
Given commits like this:
| Author: Suresh Siddha <suresh.b.siddha@intel.com>
| Date: Tue Jul 29 10:29:19 2008 -0700
|
| x86, xsave: enable xsave/xrstor on cpus with xsave support
Which deliberately expose boot cpu dependence to pieces of the system,
I think it's time to explicitly have a variable for it to prevent this
continual misassumption that the boot CPU is zero.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: allow /dev/mem mmaps on non-PAT CPUs/platforms
Fix mmap to /dev/mem when CONFIG_X86_PAT is off and CONFIG_STRICT_DEVMEM is
off
mmap to /dev/mem on kernel memory has been failing since the
introduction of PAT (CONFIG_STRICT_DEVMEM=n case). Seems like
the check to avoid cache aliasing with PAT is kicking in even
when PAT is disabled. The bug seems to have crept in 2.6.26.
This patch makes sure that the mmap to regular
kernel memory succeeds if CONFIG_STRICT_DEVMEM=n and
PAT is disabled, and the checks to avoid cache aliasing
still happens if PAT is enabled.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Tested-by: Tim Sirianni <tim@scalemp.com>
Cc: <stable@kernel.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix build failure on x86/Voyager
Before:
| commit 329513a35d
| Author: Yinghai Lu <yhlu.kernel@gmail.com>
| Date: Wed Jul 2 18:54:40 2008 -0700
|
| x86: move prefill_possible_map calling early
prefill_possible_mask() was hidden under CONFIG_HOTPLUG_CPU rendering
it invisitble to voyager. Since this commit it's exposed, but not
provided by the voyager subarch, so add a dummy stub to fix the link
breakage.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix x86/Voyager boot
CONFIG_SMP is used for features which work on *all* x86 boxes.
CONFIG_X86_SMP is used for standard PC like x86 boxes (for things like
multi core and apics)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: boot up secondary CPUs as well on x86/Voyager systems
This commit:
| commit 3e9704739d
| Author: Glauber Costa <gcosta@redhat.com>
| Date: Wed May 28 13:01:54 2008 -0300
|
| x86: boot secondary cpus through initial_code
removed the use of initialize_secondary. However, it didn't update
voyager, so the secondary cpus no longer boot. Fix this by adding the
initial_code switch to voyager as well.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
CHAR: Delete old and now unused M48T35 RTC driver for SGI IP27.
CHAR: Delete old and now unused DS1286 driver.
MIPS: Sort out CPU type to name translation.
MIPS: Use the new byteorder headers
MIPS: Probe for watch registers on cores of all vendors, not just MTI.
MIPS: Switch FPU emulator trap to BREAK instruction.
MIPS: SMP: Do not initialize __cpu_number_map/__cpu_logical_map for CPU 0.
MIPS: Consider value of c0_ebase when computing value of exception base.
MIPS: Clean up MIPSxx-optimized bitop functions
MIPS: New feature test macro cpu_has_mips_r
MIPS: RBTX4927: Add GPIO-LED support
MIPS: TXx9: Fix RBTX4939 ethernet address initialization
Impact: include file dependency cleanup
Fix compile errors of files that include asm/uv/uv_hub.h but do
not include linux/timer.h.
[ such files are not mainline right now. ]
Signed-of-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
i2c_board_info array was filled incorrectly.
Due to circumstances, the way it is filled works.
This patch fills array properly.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mx31ads_defconfig compilation failed with
arch/arm/mach-mx3/mx31ads.c: In function 'mxc_init_imx_uart':
arch/arm/mach-mx3/mx31ads.c:102: error: 'mxc_uart_device0' undeclared (first use in this function)
arch/arm/mach-mx3/mx31ads.c:102: error: (Each undeclared identifier is reported only once
arch/arm/mach-mx3/mx31ads.c:102: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-mx3/mx31ads.o] Error 1
Add missing include
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Data register holds the value we have written to a gpio. To
get the input value we must read the Pad Status Register MX3 (or Sample
Status register in MX1/2 terms)
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The internal devices of the MX3 Processor have to be mapped
MT_DEVICE_NONSHARED devices, otherwise cache corruptions occur.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It was only used by this one SGI platform which recently was converted to
RTC_LIB and with RTC_LIB enabled the legacy drivers are no more selectable.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was only used by two SGI platforms which recently were converted to
RTC_LIB and with RTC_LIB enabled the legacy drivers are no more selectable.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
As noticed by David Daney <ddaney@caviumnetworks.com>, the old long switch
statement did not comply with the Linux C coding style. It was also yet
another place of code to be changed when adding a new processor type
leading to annoying bugs for example in /proc/cpuinfo.
Fixed by moving the setting of the CPU type string into the core of the
probing code and a few BUG_ON() test to ensure the CPU probing code indeed
did its job and removing multiple now redundant tests.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Arguably using the address error handler has always been ugly. But with
processors that handle unaligned loads and stores in hardware the
current mechanism ceases to work so switch it to a BREAK instruction and
allocate break code 514 to the FPU emulator.
Yoichi Yuasa provided a build fix for CONFIG_BUG=n.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
A system isn't necessarily booted on physical processor 0 as this code
assumes. Also the array happens to be allocated in .bss so it's zero
initialized anyway. Systems which need to override this can do so in
their mp_ops->smp_setup() method.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It just so happens to be zero on all currently supported systems so this
hasn't bitten yet ...
[Ralf: Original patch from Cavium; handling of set_uncached_handler() and
de-ifdef'ed trap_init() implementation by me.]
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the arm architecture.
DaVinci is skipped on purpose to simplify the merge process for patches
switching it over to use gpiolib as per request by David Brownell.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix compilation of sharpsl_pm when CONFIG_PM in unselected.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Impact: cleanup
To the unsuspecting user it is quite annoying that this broken and
inconsistent with x86-64 definition still exists.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The internal devices of the MX3 Processor have to be mapped
MT_DEVICE_NONSHARED devices, otherwise cache corruptions occur.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Shift the first year to 1968 for Sun SPARC machines.
Move this logic from platform specific files to rtc driver
as this fixes problems with calculating a century bit.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Alexander Beregalov
Signed-off-by: David S. Miller <davem@davemloft.net>
__raw_write avoids the need to byteswap, as we are reading from a
host-endian area, just deref the pointers directly, taking care
of alignment.
As before, outsw must be called with a 2-byte aligned pointer.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: remove incorrect WARN_ON(1)
Gets rid of dmesg spam created during physical memory hot-add which
will very likely confuse users. The change removes what appears to
be debugging code which I assume was unintentionally included in:
x86: arch/x86/mm/init_64.c printk fixes
commit 10f22dde55
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: some new sparse warnings in e820.c etc, but no functional change.
As with regular ioremap, iounmap etc, annotate with __iomem.
Fixes the following sparse warnings, will produce some new ones
elsewhere in arch/x86 that will get worked out over time.
arch/x86/mm/ioremap.c:402:9: warning: cast removes address space of expression
arch/x86/mm/ioremap.c:406:10: warning: cast adds address space to expression (<asn:2>)
arch/x86/mm/ioremap.c:782:19: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
corgi_lcd has symbol conflict with corgi_bl driver.
Fix it by renaming common symbol in new corgi_lcd driver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
ftrace: fix current_tracer error return
tracing: fix a build error on alpha
ftrace: use a real variable for ftrace_nop in x86
tracing/ftrace: make boot tracer select the sched_switch tracer
tracepoint: check if the probe has been registered
asm-generic: define DIE_OOPS in asm-generic
trace: fix printk warning for u64
ftrace: warning in kernel/trace/ftrace.c
ftrace: fix build failure
ftrace, powerpc, sparc64, x86: remove notrace from arch ftrace file
ftrace: remove ftrace hash
ftrace: remove mcount set
ftrace: remove daemon
ftrace: disable dynamic ftrace for all archs that use daemon
ftrace: add ftrace warn on to disable ftrace
ftrace: only have ftrace_kill atomic
ftrace: use probe_kernel
ftrace: comment arch ftrace code
ftrace: return error on failed modified text.
ftrace: dynamic ftrace process only text section
...
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: fix irqs on/off ip tracing
lockdep: minor fix for debug_show_all_locks()
x86: restore the old swiotlb alloc_coherent behavior
x86: use GFP_DMA for 24bit coherent_dma_mask
swiotlb: remove panic for alloc_coherent failure
xen: compilation fix of drivers/xen/events.c on IA64
xen: portability clean up and some minor clean up for xencomm.c
xen: don't reload cr3 on suspend
kernel/resource: fix reserve_region_with_split() section mismatch
printk: remove unused code from kernel/printk.c
Impact: fix AMD Family 11h boot hangs / USB device problems
The AMD Fam11h CPUs have a K8 northbridge. This northbridge is different
from other family's because it lacks GART support (as I just learned).
But the kernel implicitly expects a GART if it finds an AMD northbridge.
Fix this by removing the Fam11h northbridge id from the scan list of K8
northbridges. This patch also changes the message in the GART driver
about missing K8 northbridges to tell that the GART is missing which is
the correct information in this case.
Reported-by: Jouni Malinen <jkmalinen@gmail.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so users are not confused with memhole causing big total ram
we don't need to worry about 32 bit, because memhole is always
above max_low_pfn.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix kdump crash on 32-bit sparsemem kernels
Since linux-2.6.27, kdump has failed on i386 sparsemem kernel.
1st-kernel gets a panic just before switching to 2nd-kernel.
The cause is that a kernel accesses invalid mem_section by
page_to_pfn(image->swap_page) at machine_kexec().
image->swap_page is allocated if kexec for hibernation, but
it is not allocated if kdump. So if kdump, a kernel should
not access the mem_section corresponding to image->swap_page.
The attached patch fixes this invalid access.
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Cc: kexec-ml <kexec@lists.infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
APIC_DEBUG is always 2.
need to update inquire_remote_apic to check apic_verbosity with
it instead.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Improve the help text of the X86_PTRACE_BTS config.
Make X86_DS invisible and depend on X86_PTRACE_BTS.
Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current defconfig for Linkstation/Kuroboxes has the "Disable Heap
Randomization" option enabled.
Since some of these machines are facing the internet, it helps to have
heap randomization enabled. This patch enables it.
Signed-off-by: Rogério Brito <rbrito@ime.usp.br>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since Linkstations and Kuroboxes often have *very* little memory (as
they are embedded systems), it is desirable to get their kernels
compiled optimized for size.
Signed-off-by: Rogério Brito <rbrito@ime.usp.br>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The i2c bus defn is broken on linkstation / kurobox machines since at
least 2.6.27. Fix it. Also remove CONFIG_SERIAL_OF_PLATFORM, which, if
enabled, breaks the serial console after the
"console handover: boot [udbg0] -> real [ttyS1]" message.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the HCU4 Kconfig option to 'default n'. We don't want the
board to always be enabled for other board defconfigs.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Common halt logic was changed by x86 and did not update ia64. This patch
updates halt for ia64.
Fixes a regression causing guests to hang with more than 2 vcpus.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Every call of kvm_set_irq() should offer an irq_source_id, which is
allocated by kvm_request_irq_source_id(). Based on irq_source_id, we
identify the irq source and implement logical OR for shared level
interrupts.
The allocated irq_source_id can be freed by kvm_free_irq_source_id().
Currently, we support at most sizeof(unsigned long) different irq sources.
[Amit: - rebase to kvm.git HEAD
- move definition of KVM_USERSPACE_IRQ_SOURCE_ID to common file
- move kvm_request_irq_source_id to the update_irq ioctl]
[Xiantao: - Add kvm/ia64 stuff and make it work for kvm/ia64 guests]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The pvmmu TLB flush handler should request a root sync, similarly to
a native read-write CR3.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This code has been dead for many years. The last update it received
was in 2003 in order to update it for the driver model changes, though
it had already been in disarray and unused before that point. The only
boards that ever used this chip have not had users in many years either,
so it is finally safe to just kill it off and move on with life.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The ISA tuning as it is today can not cope with all of the different
variations that are possible, so all we can do is a best attempt based on
the CPU family. The DSP and FPU generation are already at odds with each
other, and the nommu tuning we weren't handling at all. Additionally,
for platforms that never had an FPU, the -nofpu variant never existed,
meaning that we would lose out on family granular tuning completely in
certain cases.
With tat out of the way, we were also using -up versions, allowing for
later instructions that branched off of a particular subset of the ISA,
but are not actually reflected on the hardware being targetted. This
leads to some confusion, and the possibility of bogus instructions on
older parts. Kill that off and lock it down to the family being built
for specifically.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The s390 kernel does not compile if virtio console is enabled, but guest
support is disabled:
LD .tmp_vmlinux1
arch/s390/kernel/built-in.o: In function `setup_arch':
/space/linux-2.5/arch/s390/kernel/setup.c:773: undefined reference to
`s390_virtio_console_init'
The fix is related to
commit 99e65c92f2
Author: Christian Borntraeger <borntraeger@de.ibm.com>
Date: Fri Jul 25 15:50:04 2008 +0200
KVM: s390: Fix guest kconfig
Which changed the build process to build kvm_virtio.c only if CONFIG_S390_GUEST
is set. We must ifdef the prototype in the header file accordingly.
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
allyesconfig and allmodconfig built kernels have a tape IPL record.
A the vmreader record makes much more sense, since hardly anybody will
ever IPL a kernel from tape. So change the default.
As I side effect I can test these kernels without fiddling around with
the kernel config ;)
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use sysdev_class_create_file() to create create sysdev class attributes
instead of sysfs_create_file(). Using sysfs_create_file() wasn't a very
good idea since the show and store functions have a different amount of
parameters for sysfs files and sysdev class files.
In particular the pointer to the buffer is the last argument and
therefore accesses to random memory regions happened.
Still worked surprisingly well until we got a kernel panic.
Cc: stable@kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current enable_sie code sets the mm->context.pgstes bit to tell
dup_mm that the new mm should have extended page tables. This bit is also
used by the s390 specific page table primitives to decide about the page
table layout - which means context.pgstes has two meanings. This can cause
any kind of bugs. For example - e.g. shrink_zone can call
ptep_clear_flush_young while enable_sie is running. ptep_clear_flush_young
will test for context.pgstes. Since enable_sie changed that value of the old
struct mm without changing the page table layout ptep_clear_flush_young will
do the wrong thing.
The solution is to split pgstes into two bits
- one for the allocation
- one for the current state
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Impact: fix crash with memory hotplug
Shuahua Li found:
| I just did some experiments on a desktop for memory hotplug and this bug
| triggered a crash in my test.
|
| Yinghai's suggestion also fixed the bug.
We don't need to round it, just remove that extra -1
Signed-off-by: Yinghai <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Presently there is very little standing in the way of using an SH-4
toolchain for building an SH-2 kernel, and vice versa. Binutils itself
has no limitations whatsoever and supports explicit ISA hinting, which
we already use with varying degrees of success today.
This leaves GCC as the odd one out, due to a rather dubious policy
decision by the GCC folks to not include all of the CPU family variants
in the default list of multilib targets in GCC4. Despite best efforts to
the contrary, libgcc itself already contains awareness of the various CPU
types and remains generally usable, allowing it to safely be referenced
even on a mismatched target (and indeed, explicit ISA tuning by binutils
keeps us honest in terms of ensuring that we do not link incompatible
objects in).
In order to support this, a couple of changes had to be made. Firstly,
the introduction of MAYBE_DECLARE_EXPORT(), which provides a __weak
extern reference for libgcc resident routines when finer-grained
-m<cpu-family> based tuning is not supported by the toolchain. This
fixes up the __sdivsi3_i4i and __udivsi3_i4i references when dealing
with SH-2 kernels linked with an SH-4 libgcc. Secondly, in case where we
are unable to find a suitable match for CPU family tuning but still
have a toolchain that defaults to FP instruction generation, a suitable
nofpu target must be selected. This is accomplished by selecting the
first nofpu multilib target supported by the toolchain, which is
also necessary for selecting the proper libgcc to link against.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure IFLUSH is not the last instruction in the hardware loop to avoid
infinite core stall.
The dcache/icache function that only gets used in writeback mode was putting
IFLUSH as the last instruction in the hardware loop ... we know from design
that this may often lead to inifite core stalling, so switch the FLUSH/IFLUSH
order.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The cache code I added flushes 1 line too little if the start address is
not aligned to the cache size. Cache align the start address so that when
we straddle cache aligns, we get the right count.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The size of the pm_signal_local array should be equal to the
number of SPUs being configured in the call. Currently, the
array is of size 4 (NR_PHYS_CTRS) but being indexed by a for
loop from 0 to 7 (NUM_SPUS_PER_NODE).
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Fixes screwing up text output when doing a make oldconfig and viewing
help text of "OProfile AMD IBS support". When the terminal is
not using an UTF8 locale / LANG. "make config" breaks terminal output
and its not possible to continue.
(Change added by changeset 852402cc Tue Jul 22 21:09:06 2008)
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Robert Richter <robert.richter@amd.com>
When booting Linux on a txx9 board with VxWorks boot loader, it crashes in
prom_getenv(), as VxWorks doesn't pass firmware parameters in a0-a3 (in my
case, the actual leftover values in these registers were 0x80002000,
0x80001fe0, 0x2000, and 0x20).
Make the parsing of argc, argv, and envp a bit more robust by checking if
argc is a number below CKSEG0, and argv/envp point to CKSEG0.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove runtime db_* macros as we don't need them any more. In general,
such helpers are useful for initial porting, but once approved, they are
not indispensable.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current EMMA2RH irq code is mess. Before cleaning it up, gather them
in one place as a first step.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We'll put all EMMA related headers there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
git mv arch/mips/{emma2rh,emma} and fixups Makefiles. We'll put all NEC
EMMA series based machines there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Move EMMA related stuff into arch/mips/emma/Kconfig
- Create CONFIG_SOC_EMMA* to handle more EMMA SoCs effectively
- Rename CONFIG_MARKEINS into CONFIG_NEC_MARKEINS
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We already have sufficient infrastructure to support VR5500 and VR5500A
series processors. Here's a Makefile support to make it selectable by
ports, and enable it for NEC EMMA2RH Markeins board.
This patch also fixes a confused target help, and adds 1Gb PageMask bits
supported by VR5500 and its variants.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following patch add support for the NXP PNX833x SOC. More
specifically it adds support for the STB222/5 variant. It fixes
the vectored interrupt issue.
Signed-off-by: daniel.j.laird <daniel.j.laird@nxp.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a typo in the comment for the TOSHIBA_RBTX4939 config option
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In file included from include/linux/ptrace.h:49,
from arch/mips/kernel/kgdb.c:25:
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:123: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:124: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:126: error: expected declaration specifiers or '...' before '__u32'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:127: error: expected declaration specifiers or '...' before '__u32'
make[1]: *** [arch/mips/kernel/kgdb.o] Error 1
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following functions
disable_local1_irq()
disable_local2_irq()
disable_local3_irq()
are needlessly defined global, so make them static. While at it, fix a
whitespace error in the same file.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add smc91x platform device to RBTX4939 board and some hacks for big endian.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add au1xmmc platform data for PB1200/DB1200 boards and wire up the 2 SD
controllers for them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch sets the correct interrupt status and level
in order to get the CompactFlash adapter working.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mips/pci/fixup-rc32434.c must #include <asm/mach-rc32434/irq.h>
This patch fixes the following compile error caused by
commit 606a083b1e
(MIPS: RB532: Cleanup the headers again):
<-- snip -->
...
CC arch/mips/pci/fixup-rc32434.o
arch/mips/pci/fixup-rc32434.c: In function 'pcibios_map_irq':
arch/mips/pci/fixup-rc32434.c:46: error: 'GROUP4_IRQ_BASE' undeclared (first use in this function)
arch/mips/pci/fixup-rc32434.c:46: error: (Each undeclared identifier is reported only once
arch/mips/pci/fixup-rc32434.c:46: error: for each function it appears in.)
make[2]: *** [arch/mips/pci/fixup-rc32434.o] Error 1
<-- snip -->
A virtually identical patch was also submitted by Yoichi Yuasa
<yoichi_yuasa@tripeaks.co.jp>.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
<asm/ptrace.h> is exported to userland so can't include <linux/ptrace.h>,
so replace the C99 types with their basic C type equivalents.
Bug originally reported and initial patch by Yoichi Yuasa
<yoichi_yuasa@tripeaks.co.jp>.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We were getting away with this for so long only because the only platform
with a non-empty plat_unmap_dma_mem() doesn't call dma_sync_sg_for_cpu()
and dma_sync_sg_for_device() from its commonly used drivers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
debugfs_create_*() returns NULL on error. Make its callers return -ENODEV
on error.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
debugfs_create_*() returns NULL on error. Make its caller debugfs_fpuemu
return -ENODEV on error.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Impact: avoid section mismatch warning, clean up
The dynamic ftrace determines which nop is safe to use at start up.
When it finds a safe nop for patching, it sets a pointer called ftrace_nop
to point to the code. All call sites are then patched to this nop.
Later, when tracing is turned on, this ftrace_nop variable is again used
to compare the location to make sure it is a nop before we update it to
an mcount call. If this fails just once, a warning is printed and ftrace
is disabled.
Rakib Mullick noted that the code that sets up the nop is a .init section
where as the nop itself is in the .text section. This is needed because
the nop is used later on after boot up. The problem is that the test of the
nop jumps back to the setup code and causes a "section mismatch" warning.
Rakib first recommended to convert the nop to .init.text, but as stated
above, this would fail since that text is used later.
The real solution is to extend Rabik's patch, and to make the ftrace_nop
into an array, and just save the code from the assembly to this array.
Now the section can stay as an init section, and we have a nop to use
later on.
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: on SGI UV platforms, fix boot crash
UV initialization is currently called too late to call alloc_bootmem_pages().
The current sequence is:
start_kernel()
mem_init()
free_all_bootmem() <--- discard of bootmem
rest_init()
kernel_init()
smp_prepare_cpus()
native_smp_prepare_cpus()
uv_system_init() <--- uses alloc_bootmem_pages()
It should be calling kmalloc().
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix guest kernel boot crash on certain configs
Recent i686 2.6.27 kernels with a certain amount of memory (between
736 and 855MB) have a problem booting under a hypervisor that supports
batched mprotect (this includes the RHEL-5 Xen hypervisor as well as
any 3.3 or later Xen hypervisor).
The problem ends up being that xen_ptep_modify_prot_commit() is using
virt_to_machine to calculate which pfn to update. However, this only
works for pages that are in the p2m list, and the pages coming from
change_pte_range() in mm/mprotect.c are kmap_atomic pages. Because of
this, we can run into the situation where the lookup in the p2m table
returns an INVALID_MFN, which we then try to pass to the hypervisor,
which then (correctly) denies the request to a totally bogus pfn.
The right thing to do is to use arbitrary_virt_to_machine, so that we
can be sure we are modifying the right pfn. This unfortunately
introduces a performance penalty because of a full page-table-walk,
but we can avoid that penalty for pages in the p2m list by checking if
virt_addr_valid is true, and if so, just doing the lookup in the p2m
table.
The attached patch implements this, and allows my 2.6.27 i686 based
guest with 768MB of memory to boot on a RHEL-5 hypervisor again.
Thanks to Jeremy for the suggestions about how to fix this particular
issue.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when copying L1 regions, go to the start of bss rather
than end since we have code to zero it out already
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
only if the cplb block overlapped with kernel area, this cplb need be locked
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
d_path() can return an error. Most of its callers do something or other to
make up something sane in that case. Do similar for blackfin's
decode_address() call to d_path().
Signed-off-by: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Rather than varying this on a subtype level, we use the counter type as a
generic identifier. This simplifies logic in the userspace tools where no
fundamental difference exists across the various subtypes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On Thu, Oct 23, 2008 at 04:09:52PM -0700, Alexander Beregalov wrote:
> arch/x86/kernel/built-in.o: In function `iommu_setup':
> pci-dma.c:(.init.text+0x36ad): undefined reference to `forbid_dac'
> pci-dma.c:(.init.text+0x36cc): undefined reference to `forbid_dac'
> pci-dma.c:(.init.text+0x3711): undefined reference to `forbid_dac
This patch partially reverts a patch to add IOMMU support to ia64. The
forbid_dac variable was incorrectly moved to quirks.c, which isn't built
when PCI is disabled.
Tested-by: "Alexander Beregalov" <a.beregalov@gmail.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 40df2d1d "[ARM] Update Xscale and Xscale3 PTE mappings" was
fingered by git-bisect for a boot failure on iop13xx. The change made
L_PTE_MT_WRITETHROUGH mappings L2-uncacheable. Russell points out that
this mapping is used for the vector page. Given the regression, and the
fact this page is used often, restore the old behaviour.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
math-emu: Fix thinko in _FP_DIV
math-emu: Fix signalling of underflow and inexact while packing result.
sparc: Add checkstack support
sparc: correct section of current_pc()
sparc: correct section of apc_no_idle
sparc64: Fix race in arch/sparc64/kernel/trampoline.S
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: drivers/ide/generic.c -> drivers/ide/ide-pci-generic.c
ide-disk: set non-rotational queue flag for SSD and CF devices
ide-cd: add TEAC CD-224E to the NO_AUTOCLOSE list
ide: Add tx4938ide driver (v2)
TXx9: Add TX4938 ATA support (v3)
ide: Add tx4939ide driver (v6)
ide: two more pci_ioremap_bar() conversions
pci: use pci_ioremap_bar() in drivers/ide
sgiioc4: use ide_host_add() (take 2)
sgiioc4: fix error cleanup path (take 2)
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC
backlight: da903x: Add backlight driver for DA9030/DA9034
tosa: add support for bl/lcd driver
backlight: add support for Sharp SL-6000 LCD and backlight drivers
Add a helper routine to register tx4938ide driver and use it on
RBTX4938 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This restores the old swiotlb alloc_coherent behavior (before the
alloc_coherent rewrite):
http://lkml.org/lkml/2008/8/12/200
The old alloc_coherent avoids GFP_DMA allocation first and if the
allocated address is not fit for the device's coherent_dma_mask, then
dma_alloc_coherent does GFP_DMA allocation. If it fails,
alloc_coherent calls swiotlb_alloc_coherent (in short, we rarely used
swiotlb_alloc_coherent).
After the alloc_coherent rewrite, dma_alloc_coherent
(include/asm-x86/dma-mapping.h) directly calls swiotlb_alloc_coherent.
It means that we possibly can't handle a device having dma_masks >
24bit < 32bits since swiotlb_alloc_coherent doesn't have the above
GFP_DMA retry mechanism.
This patch fixes x86's swiotlb alloc_coherent to use the GFP_DMA retry
mechanism, which dma_generic_alloc_coherent() provides now
(pci-nommu.c and GART IOMMU driver also use
dma_generic_alloc_coherent).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
dma_alloc_coherent (include/asm-x86/dma-mapping.h) avoids GFP_DMA
allocation first and if the allocated address is not fit for the
device's coherent_dma_mask, then dma_alloc_coherent does GFP_DMA
allocation. This is because dma_alloc_coherent avoids precious GFP_DMA
zone if possible. This is also how the old dma_alloc_coherent
(arch/x86/kernel/pci-dma.c) works.
However, if the coherent_dma_mask of a device is 24bit, there is no
point to go into the above GFP_DMA retry mechanism. We had better use
GFP_DMA in the first place.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix section mismatch warning - apic_x2apic_phys
x86: fix section mismatch warning - apic_x2apic_cluster
x86: fix section mismatch warning - apic_x2apic_uv_x
x86: fix section mismatch warning - apic_physflat
x86: fix section mismatch warning - apic_flat
x86: memtest fix use of reserve_early()
x86 syscall.h: fix argument order
x86/tlb_uv: remove strange mc146818rtc include
x86: remove redundant KERN_DEBUG on pr_debug
x86: do_boot_cpu - check if we have ESR register
x86: MAINTAINERS change for AMD microcode patch loader
x86/proc: fix /proc/cpuinfo cpu offline bug
x86: call dmi-quirks for HP Laptops after early-quirks are executed
x86, kexec: fix hang on i386 when panic occurs while console_sem is held
MCE: Don't run 32bit machine checks with interrupts on
x86: SB600: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: make variables static
* 'v28-range-hrtimers-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
hrtimers: add missing docbook comments to struct hrtimer
hrtimers: simplify hrtimer_peek_ahead_timers()
hrtimers: fix docbook comments
DECLARE_PER_CPU needs linux/percpu.h
hrtimers: fix typo
rangetimers: fix the bug reported by Ingo for real
rangetimer: fix BUG_ON reported by Ingo
rangetimer: fix x86 build failure for the !HRTIMERS case
select: fix alpha OSF wrapper
select: fix alpha OSF wrapper
hrtimer: peek at the timer queue just before going idle
hrtimer: make the futex() system call use the per process slack value
hrtimer: make the nanosleep() syscall use the per process slack
hrtimer: fix signed/unsigned bug in slack estimator
hrtimer: show the timer ranges in /proc/timer_list
hrtimer: incorporate feedback from Peter Zijlstra
hrtimer: add a hrtimer_start_range() function
hrtimer: another build fix
hrtimer: fix build bug found by Ingo
hrtimer: make select() and poll() use the hrtimer range feature
...
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix GPIO initcall breakage
avr32: Scale loops_per_jiffy when cpu frequency changes
avr32: Fix bug in LCD pin setup on port C
avr32: Add defconfig for the favr-32 board
avr32: Add defconfig for the mimc200 board
avr32: Add MIMC200 board support
avr32: Fix MIMC200 board use of SPD network pins
avr32: add support for EarthLCD Favr-32 board
avr32: Add support for EVKLCD10X addon boards
avr32: Kconfig: Remove pointless if around atstk1000 include
* git://git.kernel.org/pub/scm/linux/kernel/git/viro/bdev: (66 commits)
[PATCH] kill the rest of struct file propagation in block ioctls
[PATCH] get rid of struct file use in blkdev_ioctl() BLKBSZSET
[PATCH] get rid of blkdev_locked_ioctl()
[PATCH] get rid of blkdev_driver_ioctl()
[PATCH] sanitize blkdev_get() and friends
[PATCH] remember mode of reiserfs journal
[PATCH] propagate mode through swsusp_close()
[PATCH] propagate mode through open_bdev_excl/close_bdev_excl
[PATCH] pass fmode_t to blkdev_put()
[PATCH] kill the unused bsize on the send side of /dev/loop
[PATCH] trim file propagation in block/compat_ioctl.c
[PATCH] end of methods switch: remove the old ones
[PATCH] switch sr
[PATCH] switch sd
[PATCH] switch ide-scsi
[PATCH] switch tape_block
[PATCH] switch dcssblk
[PATCH] switch dasd
[PATCH] switch mtd_blkdevs
[PATCH] switch mmc
...
* 'x86/um-header' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits)
x86: canonicalize remaining header guards
x86: drop double underscores from header guards
x86: Fix ASM_X86__ header guards
x86, um: get rid of uml-config.h
x86, um: get rid of arch/um/Kconfig.arch
x86, um: get rid of arch/um/os symlink
x86, um: get rid of excessive includes of uml-config.h
x86, um: get rid of header symlinks
x86, um: merge Kconfig.i386 and Kconfig.x86_64
x86, um: get rid of sysdep symlink
x86, um: trim the junk from uml ptrace-*.h
x86, um: take vm-flags.h to sysdep
x86, um: get rid of uml asm/arch
x86, um: get rid of uml highmem.h
x86, um: get rid of uml unistd.h
x86, um: get rid of system.h -> system.h include
x86, um: uml atomic.h is not needed anymore
x86, um: untangle uml ldt.h
x86, um: get rid of more uml asm/arch uses
x86, um: remove dead header (uml module-generic.h; never used these days)
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits)
dock: make dock driver not a module
ACPI: fix ia64 build warning
ACPI: hack around sysfs warning with link order
ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n
intel_menlo: fix build warning
panasonic-laptop: fix build
ACPICA: Update version to 20080926
ACPICA: Add support for zero-length buffer-to-string conversions
ACPICA: New: Validation for predefined ACPI methods/objects
ACPICA: Fix for implicit return compatibility
ACPICA: Fixed a couple memory leaks associated with "implicit return"
ACPICA: Optimize buffer allocation procedure
ACPICA: Fix possible memory leak, error exit path
ACPICA: Fix fault after mem allocation failure in AML parser
ACPICA: Remove unused ACPI register bit definition
ACPICA: Update version to 20080829
ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname
ACPICA: Cleanup for internal Reference Object
ACPICA: Update comments - no functional changes
ACPICA: Update for Reference ACPI_OPERAND_OBJECT
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: asm/gpio.h needs linux/kernel.h for might_sleep()/WARN_ON().
sh: mach-highlander: Handle SCIF pinmuxing on R7785RP.
sh: sh7785 pinmux support
sh: update defconfigs.
sh: Kill off unused p1fc divisors from SH7763 clk fwk.
sh: improve pinmux support for single direction pins
sh: use 10MHz VIO_CLK for ov772x on Migo-R
sh: Update gpio_set_value() pin value handling
sh: update ov772x byte order on Migo-R
rtc: Add R2025S/D comment to rs5c372 Kconfig entry.
sh: Export cache flush routines needed by sh_eth on SH7619.
sh: Wire up oops reporting in the die notifier chain.
sh: ap325rxa: Kill off unused port definitions.
sh: Hook up PB0->PB7 input-only pins in SH7203 PFC.
sh: ap325rxa: Move off of hardcoded pinmux for flctl initialization.
sh: add support FLCTL for ap325rxa board
sh: gpio: Stub in dummy GPIO<->IRQ mapping routines.
sh: rsk7203: leds-gpio support for RSK+ LEDs.
sh: gpio: Include asm-generic/gpio.h for non-gpiolib stubs.
sh: fix soc-camera compile breakage on Migo-R.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rric/oprofile: (21 commits)
OProfile: Fix buffer synchronization for IBS
oprofile: hotplug cpu fix
oprofile: fixing whitespaces in arch/x86/oprofile/*
oprofile: fixing whitespaces in arch/x86/oprofile/*
oprofile: fixing whitespaces in drivers/oprofile/*
x86/oprofile: add the logic for enabling additional IBS bits
x86/oprofile: reordering functions in nmi_int.c
x86/oprofile: removing unused function parameter in add_ibs_begin()
oprofile: more whitespace fixes
oprofile: whitespace fixes
OProfile: Rename IBS sysfs dir into "ibs_op"
OProfile: Rework string handling in setup_ibs_files()
OProfile: Rework oprofile_add_ibs_sample() function
oprofile: discover counters for op ppro too
oprofile: Implement Intel architectural perfmon support
oprofile: Don't report Nehalem as core_2
oprofile: drop const in num counters field
Revert "Oprofile Multiplexing Patch"
x86, oprofile: BUG: using smp_processor_id() in preemptible code
x86/oprofile: fix on_each_cpu build error
...
Manually fixed trivial conflicts in
drivers/oprofile/{cpu_buffer.c,event_buffer.h}
* git://git.infradead.org/iommu-2.6:
Admit to maintaining VT-d, for my sins.
dmar: fix uninitialised 'ret' variable in dmar_parse_dev()
intel-iommu: use coherent_dma_mask in alloc_coherent
amd_iommu: fix nasty bug that caused ILLEGAL_DEVICE_TABLE_ENTRY errors
intel-iommu: IA64 support
dmar: remove the quirk which disables dma-remapping when intr-remapping enabled
dmar: Use queued invalidation interface for IOTLB and context invalidation
dmar: context cache and IOTLB invalidation using queued invalidation
dmar: use spin_lock_irqsave() in qi_submit_sync()
Linus Torvalds
Al Viro
Jesper Nilsson
Carl Love
Robert Richter
Paul Mackerras
Venki Pallipadi
Jon Smirl
David Gibson
Keith Packard
Ingo Molnar
Mike Dyer
Yoshihiro Shimoda
Kuninori Morimoto
Paul Mundt
Harvey Harrison
David S. Miller
Kumar Gala
Mark Nelson
Benjamin Herrenschmidt
Nathan Fontenot
Jeremy Kerr
Michael Neuling
Milton Miller
Trent Piepho
Rusty Russell
James Bottomley
Ravikiran G Thirumalai
Josh Boyer
Mike Travis
Alexey Dobriyan
Joerg Roedel
Sergey Lapin
Russell King
Sascha Hauer
Darius Augulis
Ralf Baechle
David Daney
Atsushi Nemoto
Uwe Kleine-König
Matthias Kaehlcke
Dmitry Baryshkov
Jan Beulich
Krzysztof Helt
Gary Hade
Dmitry Baryshkov
Yinghai Lu
Ken'ichi Ohmichi
Peter Oruba
Markus Metzger
Rogério Brito
Guennadi Liakhovetski
Xiantao Zhang
Sheng Yang
Marcelo Tosatti
Christian Borntraeger
Heiko Carstens
Roel Kluin
Shaohua Li
Jie Zhang
Mike Frysinger
Michael Hennerich
Robin Getz
Jesper Dangaard Brouer
Zhang Le
Geert Uytterhoeven
Shinya Kuribayashi
Phil Sutter
Daniel Laird
Yoichi Yuasa
Dmitri Vorobiev
Manuel Lauss
Florian Fainelli
Adrian Bunk
Zhaolei
Steven Rostedt
Cliff Wickman
Chris Lalancette
Graf Yang
Tim Pepper
Fenghua Yu
Dan Williams
FUJITA Tomonori
Nicolas Pitre