pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation for multi-phase support, add 'phase' parameter to read_word
and set_page functions. Actual multi-phase support will be added in
a subsequent patch.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Build bot reports the following build issue after commit 9091373ab7
("gpio: remove less important #ifdef around declarations):
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:576:1: error: redefinition of 'gpiochip_add_pin_range'
gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
include/linux/gpio.h:245:1: note: previous definition of 'gpiochip_add_pin_range' was here
gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:583:1: error: redefinition of 'gpiochip_add_pingroup_range'
gpiochip_add_pingroup_range(struct gpio_chip *chip,
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
include/linux/gpio.h:254:1: note: previous definition of 'gpiochip_add_pingroup_range' was here
gpiochip_add_pingroup_range(struct gpio_chip *chip,
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:591:1: error: redefinition of 'gpiochip_remove_pin_ranges'
gpiochip_remove_pin_ranges(struct gpio_chip *chip)
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
include/linux/gpio.h:263:1: note: previous definition of 'gpiochip_remove_pin_ranges' was here
gpiochip_remove_pin_ranges(struct gpio_chip *chip)
This is caused by conflicting defines from linux/gpio.h and
linux/gpio/driver.h. Drivers should not include both the legacy and
the new API headers. This driver doesn't even use linux/gpio.h so
remove it.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190808080144.6183-1-brgl@bgdev.pl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/pmbus/ucd9000.c:154:34: warning:
‘ucd9000_of_match’ defined but not used
Mark ucd9000_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Expose the gpiN_fault fields of mfr_status as individual debugfs
attributes. This provides a way for users to be easily notified of gpi
faults. Also provide the whole mfr_status register in debugfs.
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a struct gpio_chip and define some methods so that this device's
I/O can be accessed via /sys/class/gpio.
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The UCD90160 Power Supply Sequencer reuses the existing register layout,
so just an id addition was required.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Ronak Desai <ronak.desai@rockwellcollins.com>
[groeck: Updated description, ordered alphabetically, added documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since devm_kzalloc() is now used to allocate driver memory, the client
driver remove function has no purpose other than to call pmbus_do_remove().
This means we can get rid of it by redefining pmbus_do_remove() to use the
same prototype, and pointing to it directly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch converts the drivers in drivers/hwmon/* to use the
module_i2c_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Guillaume Ligneul <guillaume.ligneul@gmail.com>
Cc: David George <david.george@ska.ac.za>
Cc: "Hans J. Koch" <hjk@hansjkoch.de>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Always call _pmbus_read_byte() instead of pmbus_read_byte() in PMBus core
driver. With this change, device specific read functions can be implemented for
all registers.
Since the device specific read_byte function is now always called, we need to be
more careful with page validations. Only fail if the passed page number is larger
than 0, since -1 means "current page".
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
EINVAL was over-used in the code. Replace it with more appropriate errors.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Driver remove functions have an error return value, but rarely return an error
in practice. If a driver does return an error from its remove function, the
driver won't be unloaded and is expected to stay alive.
pmbus_do_remove() is defined as returning an int, but always returns 0 (no
error). Calling code passes that return value on to high level driver
remove functions, but does not evaluate it and removes driver data even if
pmbus_do_remove() returned an error (which it in practice never does). Even if
this code could never cause a real problem, it is nevertheless conceptually
wrong.
To reduce confusion and simplify the code, change pmbus_do_remove() to be a void
function, and have PMBus client drivers always return zero in their driver
remove functions.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Rewrite the loop walking the id array during probe. The new code is
better adapted to a null-terminated array, and is also clearer and
more efficient than the original.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Since the number of PMBus drivers is getting large, move them into
directory drivers/hwmon/pmbus to improve readability and scalability.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Stephen Kitt
Guenter Roeck
Jim Wright
Bartosz Golaszewski
Thomas Gleixner
Kees Cook
Christopher Bostic
Wolfram Sang
Javier Martinez Canillas
Matt Weber
Axel Lin
Guenter Roeck
Jean Delvare