As the options passed to ip6_append_data may be ephemeral, we need
to duplicate it for corking. This patch applies the simplest fix
which is to memdup all the relevant bits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP header pointer assignment must happen after calling
pskb_may_pull(). As pskb_may_pull() can potentially alter the SKB
buffer.
This was exposted by running multicast traffic through the NIU driver,
as it won't prepull the protocol headers into the linear area on
receive.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 93821778de (udp: Fix rcv socket
locking) accidentally removed sk_drops increments for UDP IPV4
sockets.
This field can be used to detect incorrect sizing of socket receive
buffers.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
packet_lookup_frames() fails to get user frame if current frame header
status contains extra flags.
This is due to the wrong assumption on the operators precedence during
frame status tests.
Fixed by forcing the right operators precedence order with explicit brackets.
Signed-off-by: Paolo Abeni <paolo.abeni@gmail.com>
Signed-off-by: Sebastiano Di Paola <sebastiano.dipaola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
igb: fix link reporting when using sgmii
igb: prevent skb_over panic w/ mtu smaller than 1K
igb: Fix DCA errors and do not use context index for 82576
ipv6: compile fix for ip6mr.c
packet: Avoid lock_sock in mmap handler
sfc: Replace stats_enabled flag with a disable count
sfc: SFX7101/SFT9001: Fix AN advertisements
sfc: SFT9001: Always enable XNP exchange on SFT9001 rev B
sfc: Update board info for hardware monitor on SFN4111T-R5 and later
sfc: Test for PHYXS faults whenever we cannot test link state bits
sfc: Reinitialise the PHY completely in case of a PHY or NIC reset
sfc: Fix post-reset MAC selection
sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1
sfc: SFT9001: Fix speed reporting in 1G PHY loopback
sfc: SFX7101: Remove workaround for bad link training
sfc: SFT9001: Enable robust link training
sky2: fix hard hang with netconsoling and iface going up
net/ipv6/ip6mr.c: In function 'pim6_rcv':
net/ipv6/ip6mr.c:368: error: implicit declaration of function 'csum_ipv6_magic'
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the mmap handler gets called under mmap_sem, and we may grab
mmap_sem elsewhere under the socket lock to access user data, we
should avoid grabbing the socket lock in the mmap handler.
Since the only thing we care about in the mmap handler is for
pg_vec* to be invariant, i.e., to exclude packet_set_ring, we
can achieve this by simply using a new mutex.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Martin MOKREJŠ <mmokrejs@ribosome.natur.cuni.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tulip: fix 21142 with 10Mbps without negotiation
drivers/net/skfp: if !capable(CAP_NET_ADMIN): inverted logic
gianfar: Fix Wake-on-LAN support
smsc911x: timeout reaches -1
smsc9420: fix interrupt signalling test failures
ucc_geth: Change uec phy id to the same format as gianfar's
wimax: fix build issue when debugfs is disabled
netxen: fix memory leak in drivers/net/netxen_nic_init.c
tun: Add some missing TUN compat ioctl translations.
ipv4: fix infinite retry loop in IP-Config
net: update documentation ip aliases
net: Fix OOPS in skb_seq_read().
net: Fix frag_list handling in skb_seq_read
netxen: revert jumbo ringsize
ath5k: fix locking in ath5k_config
cfg80211: print correct intersected regulatory domain
cfg80211: Fix sanity check on 5 GHz when processing country IE
iwlwifi: fix kernel oops when ucode DMA memory allocation failure
rtl8187: Fix error in setting OFDM power settings for RTL8187L
mac80211: remove Michael Wu as maintainer
...
As reported by Toralf Förster and Randy Dunlap.
- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html
- http://lkml.org/lkml/2009/1/29/279
The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.
These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It oopsd for me in skb_seq_read. addr2line said it was
linux-2.6/net/core/skbuff.c:2228, which is this line:
while (st->frag_idx < skb_shinfo(st->cur_skb)->nr_frags) {
I added some printks in there and it looks like we hit this:
} else if (st->root_skb == st->cur_skb &&
skb_shinfo(st->root_skb)->frag_list) {
st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
st->frag_idx = 0;
goto next_skb;
}
Actually I did some testing and added a few printks and found that the
st->cur_skb->data was 0 and hence the ptr used by iscsi_tcp was null.
This caused the kernel panic.
if (abs_offset < block_limit) {
- *data = st->cur_skb->data + abs_offset;
+ *data = st->cur_skb->data + (abs_offset - st->stepped_offset);
I enabled the debug_tcp and with a few printks found that the code did
not go to the next_skb label and could find that the sequence being
followed was this -
It hit this if condition -
if (st->cur_skb->next) {
st->cur_skb = st->cur_skb->next;
st->frag_idx = 0;
goto next_skb;
And so, now the st pointer is shifted to the next skb whereas actually
it should have hit the second else if first since the data is in the
frag_list.
else if (st->root_skb == st->cur_skb &&
skb_shinfo(st->root_skb)->frag_list) {
st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
goto next_skb;
}
Reversing the two conditions the attached patch fixes the issue for me
on top of Herbert's patches.
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The frag_list handling was broken in skb_seq_read:
1) We didn't add the stepped offset when looking at the head
are of fragments other than the first.
2) We didn't take the stepped offset away when setting the data
pointer in the head area.
3) The frag index wasn't reset.
This patch fixes both issues.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_CFG80211_REG_DEBUG is enabled and an intersection
occurs we are printing the regulatory domain passed by CRDA
and indicating its the intersected regulatory domain. Lets fix
this and print the intersection as originally intended.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two issues with the sanity check loop when processing
the country IE:
1. Do not use frequency for the current subband channel check,
this was a big fat typo.
2. Apply the 5 GHz 4-channel steps when considering max channel
on each subband as was done with a recent patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kernel manages this value internally, as necessary, as
VIFs are added/removed and as multicast routers are registered
and deregistered.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the IPv6 multicast routing issues described
below. It was tested with XORP 1.4/1.5 as the IPv6 PIM-SM routing
daemon against FreeBSD peers.
net/ipv6/ip6_input.c:
- Don't try to forward link-local multicast packets.
- Don't reset skb2->dev before calling ip6_mr_input() so packets can
be identified as coming from the PIM register vif properly.
net/ipv6/ip6mr.c:
- Fix incoming PIM register messages processing:
* The IPv6 pseudo-header should be included when checksumming PIM
messages (RFC 4601 section 4.9; RFC 3973 section 4.7.1).
* Packets decapsulated from PIM register messages should have
skb->protocol ETH_P_IPV6.
- Enable/disable IPv6 multicast forwarding on the corresponding
interface when a routing daemon adds/removes a multicast virtual
interface.
- Remove incorrect skb_pull() to fix userspace signaling.
- Enable/disable global IPv6 multicast forwarding when an IPv6
multicast routing socket is opened/closed.
net/ipv6/route.c:
- Don't use strict routing logic for packets decapsulated from PIM
register messages (similar to disabling rp_filter for the IPv4
case).
Signed-off-by: Thomas Goff <thomas.goff@boeing.com>
Reviewed-by: Fred Templin <fred.l.templin@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the xfrm reverse flow lookup for icmp6 so that icmp6 packets
don't get lost over ipsec tunnels. Similar patch is in RHEL5 kernel for a quite
long time and I do not see why it isn't in mainline.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_splice_data_recv has two lengths to consider: the len parameter it
gets from tcp_read_sock, which specifies the amount of data in the skb,
and rd_desc->count, which is the amount of data the splice caller still
wants. Currently it passes just the latter to skb_splice_bits, which then
splices min(rd_desc->count, skb->len - offset) bytes.
Most of the time this is fine, except when the skb contains urgent data.
In that case len goes only up to the urgent byte and is less than
skb->len - offset. By ignoring len tcp_splice_data_recv may a) splice
data tcp_read_sock told it not to, b) return to tcp_read_sock a value > len.
Now, tcp_read_sock doesn't handle used > len and leaves the socket in a
bad state (both sk_receive_queue and copied_seq are bad at that point)
resulting in duplicated data and corruption.
Fix by passing min(rd_desc->count, len) to skb_splice_bits.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9088c56095
(udp: Improve port randomization) introduced a regression for UDP bind() syscall
to null port (getting a random port) in case lot of ports are already in use.
This is because we do about 28000 scans of very long chains (220 sockets per chain),
with many spin_lock_bh()/spin_unlock_bh() calls.
Fix this using a bitmap (64 bytes for current value of UDP_HTABLE_SIZE)
so that we scan chains at most once.
Instead of 250 ms per bind() call, we get after patch a time of 2.9 ms
Based on a report from Vitaly Mayatskikh
Reported-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (92 commits)
gianfar: Revive VLAN support
vlan: Export symbols as non GPL symbols.
bnx2x: tx_has_work should not wait for FW
netxen: reduce memory footprint
netxen: fix vlan tso/checksum offload
net: Fix linux/if_frad.h's suitability for userspace.
net: Move config NET_NS to from net/Kconfig to init/Kconfig
isdn: Fix missing ifdef in isdn_ppp
networking: document "nc" in addition to "netcat" in netconsole.txt
e1000e: workaround hw errata
af_key: initialize xfrm encap_oa
virtio_net: Fix MAX_PACKET_LEN to support 802.1Q VLANs
lcs: fix compilation for !CONFIG_IP_MULTICAST
rtl8187: Add termination packet to prevent stall
iwlwifi: fix rs_get_rate WARN_ON()
p54usb: fix packet loss with first generation devices
sctp: Fix another socket race during accept/peeloff
sctp: Properly timestamp outgoing data chunks for rtx purposes
sctp: Correctly start rtx timer on new packet transmissions.
sctp: Fix crc32c calculations on big-endian arhes.
...
In previous kernels, any kernel module could get access to the
'real-device' and the VLAN-ID for a particular VLAN. In more recent
kernels, the code was restructured such that this is hard to do
without accessing private .h files for any module that cannot use
GPL-only symbols.
Attached is a patch to once again allow non-GPL modules the ability to
access the real-device and VLAN id for VLANs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make NET_NS available underneath the generic Namespaces config option
since all of the other namespace options are there.
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently encap_oa is left uninitialized, so it contains garbage data which
is visible to userland via Netlink. Initialize it by zeroing it out.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between sctp_rcv() and sctp_accept() where we
have moved the association from the listening socket to the
accepted socket, but sctp_rcv() processing cached the old
socket and continues to use it.
The easy solution is to check for the socket mismatch once we've
grabed the socket lock. If we hit a mis-match, that means
that were are currently holding the lock on the listening socket,
but the association is refrencing a newly accepted socket. We need
to drop the lock on the old socket and grab the lock on the new one.
A more proper solution might be to create accepted sockets when
the new association is established, similar to TCP. That would
eliminate the race for 1-to-1 style sockets, but it would still
existing for 1-to-many sockets where a user wished to peeloff an
association. For now, we'll live with this easy solution as
it addresses the problem.
Reported-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to the retransmit code exposed a long standing
bug where it was possible for a chunk to be time stamped
after the retransmit timer was reset. This caused a rare
situation where the retrnamist timer has expired, but
nothing was marked for retrnasmission because all of
timesamps on data were less then 1 rto ago. As result,
the timer was never restarted since nothing was retransmitted,
and this resulted in a hung association that did couldn't
complete the data transfer. The solution is to timestamp
the chunk when it's added to the packet for transmission
purposes. After the packet is trsnmitted the rtx timer
is restarted. This guarantees that when the timer expires,
there will be data to retransmit.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 62aeaff5cc
(sctp: Start T3-RTX timer when fast retransmitting lowest TSN)
introduced a regression where it was possible to forcibly
restart the sctp retransmit timer at the transmission of any
new chunk. This resulted in much longer timeout times and
sometimes hung sctp connections.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wlan0: switched to short barker preamble (BSSID=00:01:aa:bb:cc:dd)
wlan0: switched to short slot (BSSID=) <something is missing here>
should be:
wlan0: switched to short barker preamble (BSSID=00:01:aa:bb:cc:dd)
wlan0: switched to short slot (BSSID=00:01:aa:bb:cc:dd)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After launching mesh discovery in tx path, reference count was not being
decremented. This was preventing module unload.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Caused by call to request_module() while holding nf_conntrack_lock.
Reported-and-tested-by: Kövesdi György <kgy@teledigit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous fix to paged packets broke the merging because it
reset the skb->len before we added it to the merged packet. This
wasn't detected because it simply resulted in the truncation of
the packet while the missing bit is subsequently retransmitted.
The fix is to store skb->len before we clobber it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a frag is shorter than an Ethernet header, we'd return a
zeroed packet instead of aborting. This patch fixes that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to perform skb_postpull_rcsum after pulling the IPv6
header in order to maintain the correctness of the complete
checksum.
This patch also adds a missing iph reload after pulling.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
register_pernet_gen_subsys omits mutex_unlock in one fail path.
Fix it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fc8c7dc1b2.
As indicated by Jiri Klimes, this won't work. These numbers are
not only used the size validation, they are also used to locate
attributes sitting after the message.
Signed-off-by: David S. Miller <davem@davemloft.net>
The trick in socket splicing where we try to convert the skb->data
into a page based reference using virt_to_page() does not work so
well.
The idea is to pass the virt_to_page() reference via the pipe
buffer, and refcount the buffer using a SKB reference.
But if we are splicing from a socket to a socket (via sendpage)
this doesn't work.
The from side processing will grab the page (and SKB) references.
The sendpage() calls will grab page references only, return, and
then the from side processing completes and drops the SKB ref.
The page based reference to skb->data is not enough to keep the
kmalloc() buffer backing it from being reused. Yet, that is
all that the socket send side has at this point.
This leads to data corruption if the skb->data buffer is reused
by SLAB before the send side socket actually gets the TX packet
out to the device.
The fix employed here is to simply allocate a page and copy the
skb->data bytes into that page.
This will hurt performance, but there is no clear way to fix this
properly without a copy at the present time, and it is important
to get rid of the data corruption.
With fixes from Herbert Xu.
Tested-by: Willy Tarreau <w@1wt.eu>
Foreseen-by: Changli Gao <xiaosuo@gmail.com>
Diagnosed-by: Willy Tarreau <w@1wt.eu>
Reported-by: Willy Tarreau <w@1wt.eu>
Fixed-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm trying to track down why people're hitting the checksum warning
in skb_gso_segment. As the problem seems to be hitting lots of
people and I can't reproduce it or locate the bug, here is a patch
to print out more details which hopefully should help us to track
this down.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The country IE number of channels on 5 GHz specifies the number
of 5 GHz channels, not the number of sequential channel numbers.
For example, if in a country IEs if the first channel given is 36
and the number of channels passed is 4 then the individual channel
numbers defined for the 5 GHz PHY by these parameters
are: 36, 40, 44, 48
not: 36, 37, 38, 39
See: http://tinyurl.com/11d-clarification
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a regression on disallowing bands introduced with the new
802.11d support. The issue is that IEEE-802.11 allows APs to send
a subset of what a country regulatory domain defines. This was clarified
in this document:
http://tinyurl.com/11d-clarification
As such it is possible, and this is what is done in practice, that a
single band 2.4 GHz AP will only send 2.4 GHz band regulatory information
through the 802.11 country information element and then the current
intersection with what CRDA provided yields a regulatory domain with
no 5 GHz information -- even though that country may actually allow
5 GHz operation. We correct this by only applying the intersection rules
on a channel if the the intersection yields a regulatory rule on the
same band the channel is on.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to make more wiphy specific judgements when
handling the channels later on.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix (delete) more mac80211 kernel-doc:
Warning(linux-2.6.28-git13//include/net/mac80211.h:375): Excess struct/union/enum/typedef member 'retry_count' description in 'ieee80211_tx_info'
Warning(linux-2.6.28-git13//net/mac80211/sta_info.h:308): Excess struct/union/enum/typedef member 'last_txrate' description in 'sta_info'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (95 commits)
b44: GFP_DMA skb should not escape from driver
korina: do not use IRQF_SHARED with IRQF_DISABLED
korina: do not stop queue here
korina: fix handling tx_chain_tail
korina: do tx at the right position
korina: do schedule napi after testing for it
korina: rework korina_rx() for use with napi
korina: disable napi on close and restart
korina: reset resource buffer size to 1536
korina: fix usage of driver_data
bnx2x: First slow path interrupt race
bnx2x: MTU Filter
bnx2x: Indirection table initialization index
bnx2x: Missing brackets
bnx2x: Fixing the doorbell size
bnx2x: Endianness issues
bnx2x: VLAN tagged packets without VLAN offload
bnx2x: Protecting the link change indication
bnx2x: Flow control updated before reporting the link
bnx2x: Missing mask when calculating flow control
...
If INET=y and INFINIBAND=y, but IPV6=m then INFINIBAND_ADDR_TRANS is set
to n and the RDMA CM functions rdma_connect() et al are not built.
However, the current config dependencies allow NET_9P_RDMA to be selected
in this, which leads to a build failure. Fix this by adding a dependency
on INFINIBAND_ADDR_TRANS to disallow NET_9P_RDMA in this case.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller
Herbert Xu
Jesper Dangaard Brouer
Randy Dunlap
Eric Dumazet
Sebastiano Di Paola
Linus Torvalds
Dave Jones
Inaky Perez-Gonzalez
Benjamin Zores
Shyam Iyer
Luis R. Rodriguez
Thomas Goff
Jiri Pirko
J. Bruce Fields
Dimitris Michailidis
Ben Greear
Matt Helsley
Timo Teras
Vlad Yasevich
Christian Lamparter
Brian Cavagnolo
Alexey Dobriyan
Patrick McHardy
Jiri Slaby
Jarek Poplawski
Roel Kluin
Roland Dreier