The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The following bug was reported by sometime back:
https://lkml.org/lkml/2016/6/29/795
This commit fixes this bug by setting value for the prefix string.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA channel names are specified through struct snd_dmaengine_pcm_config
rather than using SND_DMAENGINE_PCM_FLAG_CUSTOM_CHANNEL_NAME flag when
booting with devicetree in order to properly support deferred probing.
Without this change the sound machine driver initialization can complete
successfully with unavailable DMA resources.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure they secondary DAI device is freed properly when asoc_dma_platform
registration fails. This change is needed for proper deferred probe support
and will help preventing situations when the CPU DAI's initialization
completes without required DMA resources.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TDM mode using PCM format now has two-bit right shift due to the
format configuration in the driver. According to Figure 4-13 in the
CS53L30 datasheet, using ASP_SCLK_INV = 0 and SHIFT_LEFT = 1 should
be the correct combination to create one-bit right shift for the DSP
type A format.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum slot number of CS53L30 is 4 while it should support
the situation that's less than 4 channels based on the rx_mask.
So when the driver validates the last slot location, it should
check the last active slot instead of always the 4th one.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spdif mclk should be 128 times of sample rate, and there is a
internal divider, the real rate of spdif mclk is mclk / (div + 1).
Hence, the original driver always get the good frequency for
48000/96000/44100/192000. But for 32000, the mclk is incorrect,
it should be 32000*128, but get 48000*128. Do not use the internal
divider here, just set all mclk to 128 * sample rate directly.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-card needs to get its card name.
This patch makes this method simple style standard.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card is creating dai_link->name / dai_link->stream_name.
These are based on CPU + Codec name, or "fe.CPU" or "be.Codec" if it
was DPCM.
This patch adds asoc_simple_card_set_dailink_name() and set dailink
name as common method.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Thanks Mark and Anatol for the discussion. According to the result,
the standard C will translate any non-zero value into true, or
false otherwise.
QUOTE:
"6.3.1.2 Boolean type
When any scalar value is converted to _Bool, the result is 0 if the
value compares equal to 0; otherwise, the result is 1
"
Thus, the "!!" idiom is removed.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The original design only covers the jack insertion logic is active low.
Add more condition to cover no matter the logic is active low and high.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds HDMI audio output support to the MT8173 RT5650 machine
driver.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
sound/soc/mediatek/mt2701/mt2701-afe-pcm.c:72:5: warning:
symbol 'mt2701_dai_num_to_i2s' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
soc-core sets the snd_soc_pcm_runtime->dev drvdata to
snd_soc_pcm_runtime in soc_post_component_init, and access
it in places like codec_reg_show.
hsw_pcm_open overwrites the drvdata to point to hsw_pcm_data,
confusing soc-core, and causing crashes when cat
/sys/devices/pci0000:00/INT3438:00/.../System PCM/codec_reg
This patch removes the set in hsw_pcm_open since it's no longer
used. commit 7ff9d6714a ("ASoC: Intel: Split hsw_pcm_data for
playback and capture") already removed all calls to
snd_soc_pcm_get_drvdata(rtd).
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like SKL we have skl_nau88l25_ssm4567 machine for KBL,
so add the ID for this machine too.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like SKL we have skl_nau88l25_max98357a machine for KBL,
so add the ID for this machine too.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like SKL, we have two more machines for KBL, so add these IDs
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform device id table expects names to be less that
20chars, so truncate the name in skl id table and
skl_nau88l25_max98357a machine.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform device id table expects names to be less that
20chars, so truncate the name in skl id table and
skl_nau88l25_ssm4567 machine.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
FW reload had two issues:
- We need to disable the core 0 on when fw fails
- Before loading firmware mark boot flag as false
This patch fixes these two
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_* API to simplify the code.
This patch also fixes the return value in probe error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ux500 platform hasn't used board files for a long time, and
nothing defines a ab8500_codec_platform_data, so we can just
remove the probing based on that and always use device tree
properties directly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This controls the volume for the line out pins of SGTL5000.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake platform is similar to Skylake. So, add machine id.
Since same machine driver supports both, add these in id table.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like in Skylake, Kabylake also uses combo jack so add Kabylake to
DMI match for combo jack configuration.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake platform is similar to Skylake. So, add the device id.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake is next generation Intel platform which has similar
audio controller to Skylake, so add the ID and driver data in
SKL driver.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we correctly error an attempt to execute an unsupported operation.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module list was not initialized for Broxton DSP code, so
initialize it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static checker warns:
Pointer 'hlink' returned from call to function 'snd_hdac_ext_bus_get_link'
at line may be NULL and will be dereferenced"
So we should always check the return of snd_hdac_ext_bus_get_link() before
referencing the link pointer
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent commit [a92ea59b74e2: ASoC: Intel: sst: only select
sst-firmware when DW DMAC is built-in] introduced more strict kconfig
dependency (depends on DW_DMAC_CORE=y) for avoiding the build failures
due to dependency messes in intel-sst. This makes, however, it
impossible to use this driver with the modularized systems,
i.e. typically on Linux distros.
The problem addressed in the commit above is that sst_dsp_new() and
sst_dsp_free() includes the firmware init / finish that call dw_*()
functions. Thus building it as built-in with DW_DMAC_CORE module
results in the missing symbols.
However, these sst_dsp functions are basically called only from the
drivers that depend on DW_DMAC_CORE already. That is, once when these
functions are split out, the rest can be independent from dw stuff.
This patch attempts to solve the issue by the following:
- Split sst-dsp stuff into two modules: snd-soc-sst-dsp and
snd-soc-sst-firmware.
- Move sst_dsp_new() and sst_dsp_free() to the latter module so that
the former module can be independent from DW_DMAC_CORE.
- Add a new kconfig SND_SOC_INTEL_SST_FIRMWARE to select the latter
module by machine drivers.
One only remaining pitfall is that each machine driver has to select
SND_SOC_INTEL_SST_FIRMWARE carefully depending on DW_DMAC_CORE.
This can't be done cleanly due to the restriction of the current
kbuild.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=988117
Fixes: a92ea59b74 ('ASoC: Intel: sst: only select sst-firmware when DW DMAC is built-in')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse rightly warns:
sound/soc/intel/atom/sst/sst_acpi.c:353:22: warning: symbol 'cht_quirk' was not declared. Should it be static?
So statify this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kbuild bot reports that we might use dai_index uninitialized.
sound/soc/intel/boards/cht_bsw_rt5645.c:391:37: warning: 'dai_index' may be used uninitialized in this function [-Wmaybe-uninitialized]
Since it is theoretically possible, set it while initializing.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP expects the actual length of parameters that is set through
TLV to be passed in large config set, so pass the actual size
received in tlv_control_set() instead of max size.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some CHT platforms use RT5645 codec which has entry 10EC5640 so add it.
Also add DMI quirk for jack detection.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98001
[Jack detection]
Suggested-by: Stephen Just <stephenjust@gmail.com>
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Surface3 device is a CHT machine, so add entry for it.
Also update the HID from BIOS.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98001
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Surface 3 is CHT based device which shows up with RT5645 codec. But the
BIOS reports ACPI ID as 5640!
To solve this, add a DMI overide for cht-5640 machine.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98001
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add an alsa control for DAC1 digital volume control function
selection. The options are:
0: Gain update immediately
1: Gain update when a zero crossing
2: Gain update when a zero crossing with a soft ramp
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
follow-up patch from c706f2e55f ASoC: atmel_ssc_dai: distinguish the
different SSC
cpu_dai id is always 0, use platform_device id to distinguish DMA
parameters of SSCs
Signed-off-by: Peter Meerwald-Stadler <p.meerwald@bct-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5645_PRIV_INDEX(0x6a) indicate the address of PR- registers. So,
it should be volatile.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The check for if the "afe" allocation failed was too late and there
wasn't a check for "afe->platform_priv".
Fixes: 43a6a7e710 ('ASoC: mediatek: add mt2701 platform driver implementation.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is useful outside the core, when one dapm element is added
at a time.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add BT implementation for mt2701 platform driver.
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the HDMI CODECs to get private data passed in in callbacks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXd3kSAAoJECTWi3JdVIfQuVcH/A3UN9SCUMjPfRvpSOr5fEV7
MRn4AHxnP0DWucN041rdTvuxJVpIcLpkj15qfJLFOYLtN0ub2YVNlic2a3pFoRtx
ajbDC//5TFvrWjEEkMAPgdALymVYwCOKLuUgSI6xBKe+RW58JIYLzz+T+NUKHor4
3tEBNSvEQL7ljZWwr9657EO/KX9PIO7juWYk2wFHyLN7YBZEz8PZDI9y37bjnpce
PjK7X5uWXss/DRwcSvKZX6MVmErn6egxzhlFon3YpSWEzqalGsEUsJxW7Jhwk8G5
XA4EntLWAQnwW2R4Jf/5+TI1DTHXsne0iRNZbVyDf//LX5GIPJp6Ck5AYI0QVTw=
=JcYF
-----END PGP SIGNATURE-----
Merge tag 'asoc-hdmi-codec-pdata' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into drm-next
ASoC: Add private data for HDMI CODEC callbacks
Allow the HDMI CODECs to get private data passed in in callbacks.
[airlied:
Add STI/mediatek patches from Arnd for drivers merged later in drm tree.]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* tag 'asoc-hdmi-codec-pdata' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound:
ASoC: hdmi-codec: callback function will be called with private data
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add machine driver and config option for MT2701.
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mt2701 platform driver implementation for playback and capture.
The implement follow DAPM structure (memory interface as FE and I2S
as BE).
Because of the hardware design, i2s out required to be enabled when
we need to enable i2s in. This patch includes the implementation.
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add supports for 16k (wideband BT) and add a general compatible
string "linux,bt-sco"
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to
devm_ioremap_resource.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to
devm_ioremap_resource.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can use simpel utils asoc_simple_card_parse_daifmt().
Let's use it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
reg-8a assign the tracking source for each ASRC tracker. The default
value is 0x0000 which means all ASRC trackers will track LRCK1. But
in most cases, we wish each ASRC tracker track the corresponding LRCK.
i.e. ASRC1 tracks LRCK1, ASRC2 tracks LRCK2 and so on. So, we rewrite
reg-8a as 0x0120.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value of reg-2f in codec rt5650 is 0x5002, not 0x1002.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_gpiod_get_optional() returns NULL when the gpio is not assigned.
So the if (PTR_ERR(cs35l33->reset_gpio) == -ENOENT) test is always false.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Allwinner A10 and later come with a hardware block that used for the
PCM and I2S interfaces.
Add a driver for it in ASoC.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver for the MAX98504 speaker amplifier. The MAX98504
is a high efficiency mono class D amplifier that features an integrated
boost converter with voltage and current sensing ADCs for Dynamic Speaker
Management.
This driver does not include support for the I2S DAI, as we wouldn't be
able to test such code in a hardware configuration where the amplifier
has only wired the analogue input.
Signed-off-by: Inha Song <ideal.song@samsung.com>
[k.kozlowski: rebased on 4.1]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[s.nawrocki: removed unused macro definitions, rewrote regulator supply
related parts, rewrote regmap configuration code, added support for speaker
enable and global chip enable through DAPM, rewritten as component driver,
added PDM DAI definition and TDM callbacks for PDM channels configuration]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
--
Changes since v2:
- added parsing of the VBAT brownout DT properties,
- removed MAX98504_REG_SPEAKER_SOURCE_SELECT register initialization,
- removed unused macro definitions.
Changes since v1:
- none.
Changes since initial version:
- added regulator supply handling,
- added DAPM widges for speaker source selection,
- added PDM DAI definition and TDM callbacks for setting up active
PDM Tx channels and I/V sense ADC data mapping,
- removed all optional DT properties, added regulator supply properties
in the DT binding.
Signed-off-by: Mark Brown <broonie@kernel.org>
add structure define and clock control function for 2701.
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify mt8173 driver implementation to use common structure.
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
implement mediatek basic structure, include common private data,
afe fe dai operator and afe platform driver.
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
move mt8173 driver to another folder and add prefix.
add config option SND_SOC_MT8173
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i.MX51 datasheet says:
Chapter 56.1.2.4 I2S Mode
...
When I2S modes are entered (I2S master (01) or I2S slave (10)),
the following settings are recommended:
...
- TX Frame Rate should be 2 i.e. (STCCR[12:8] = 1)
- RX Frame Rate should be 2 i.e. (SRCCR[12:8] = 1)
Chapter 56.3.3.12 SSI Transmit and Receive Clock Control Registers (STCCR & SRCCR)
...
Bits 12-8 DC4-DC0
Frame Rate Divider Control. These bits are used to control the divide ratio
for the programmable frame rate dividers. The divide ratio works on the word
clock. In Normal mode, this ratio determines the word transfer rate.
In Network mode, this ratio sets the number of words per frame. The divide
ratio ranges from 1 to 32 in Normal mode and from 2 to 32 in Network mode.
In Normal mode, a divide ratio of 1 (DC=00000) provides continuous periodic
data word transfer. A bit-length frame sync must be used in this case.
Function fsl_ssi_hw_params() setup Normal mode for MONO output,
so with DC=0, SSI enters to continuous periodic data word transfer.
To fix this, setup DC for any I2S mode.
Patch has tested on custom board based on Digi CCMX-51 module (i.MX51).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC has simple-card driver which is supporting both
platform and DT probe.
Now, some sound cards driver are created based on simple-card.
They have similar feature or function, but implemented separately
on each drivers. This is a waste of code.
OTOH, merging these driver into same driver is highly risk,
because it will be very difficult to keep compatibility.
More over, ALSA SoC want to have graph base of DT feature in the
future. Maybe it want to use simple-card like feature / function.
Because of these background, this patch creates simple-card
helper utils, and provides common function to each drivers.
1st is asoc_simple_card_parse_daifmt()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card supports snd_soc_jack/pin/gpio.
These code are very similar, but driver has verbosity code.
So, this patch adds new snd_soc_jack and cleanups code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added cs35l33 driver produces a harmless warning when
CONFIG_PM is disabled:
sound/soc/codecs/cs35l33.c:908:12: error: 'cs35l33_runtime_suspend' defined but not used [-Werror=unused-function]
sound/soc/codecs/cs35l33.c:868:12: error: 'cs35l33_runtime_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations to shut up the warning
regardless of the configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is done by ASoC core now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code uses devm_request_threaded_irq() so it does not need to
explicitly call free_irq() in .probe error path and .remove.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current hdmi-codec driver is assuming that it will be registered
from HDMI driver. Because of this assumption, each callback function
has struct device pointer which is parent device (= HDMI).
Then, it can use dev_get_drvdata() to get private data.
OTOH, on some SoC/HDMI case, SoC has VIDEO/SOUND and HDMI IPs.
This case, it needs SoC VIDEO, SoC SOUND and HDMI video, HDMI codec
driver. In DesignWare HDMI IP case, SoC VIDEO (= DRM/KMS) driver tries
to bind DesignWare HDMI video driver, and HDMI codec driver
(= hdmi-codec). This case, above "parent device" of HDMI codec driver
is DRM/KMS driver and its "device" already has private data.
And, from DT and ASoC CPU/Codec/Card binding point of view, HDMI codec
(= hdmi-codec) needs to have "parent device" (= DRM/KMS), otherwise,
it never detect sound card.
Because of these reasons, some driver can't use dev_get_drvdata() to
get private data on hdmi-codec driver. This patch add new void pointer
on hdmi_codec_pdata for private data, and callback function will be
called with it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/cs35l33.c:1301:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of the Cirrus Logic cs35l33 8V boosted class D
amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is log spam while doing playback, record or reloading the
audio firmware.
print_hex_dump uses printk(KERN_DEBUG,... which is different from
dev_dbg used elsewhere in the driver: it's always enabled at
compile-time. Change it to print_hex_dump_debug for logging consistency.
For consistency with other log statements, change dev_info to dev_dbg
for a kernel print which is frequently printed by the driver.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For consistency with other log statements, change dev_info to dev_dbg
for a kernel print which is frequently printed by the driver.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdac_hdmi codec driver prints the ELD information everytime an
external monitor is connected. Make it so that the information is only
printed when someone trying to debug the driver explicitly enables it.
print_hex_dump_bytes (which just calls print_hex_dump) uses
printk(KERN_DEBUG,... which is different from dev_dbg used elsewhere in
the driver: it's always enabled at compile-time. Change it to
print_hex_dump_debug for logging consistency.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change converts the driver from using the of_* functions to using
the device_* and fwnode_* functions for accssing FW related data.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in pr_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we correctly error an attempt to execute an unsupported operation.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace goto err_gpio by return ret
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Tested-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DAPM support and updated rx51 accordingly.
As a consequence:
- the exported function tpa6130a2_stereo_enable is not needed anymore
- the mutex is dealt in the DAPM
- the power state is tracked by the DAPM
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Tested-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we correctly error an attempt to execute an unsupported operation.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop redundant include of moduleparam.h
The Coccinelle semantic patch used to make this change is as follows:
@ includesmodule @
@@
@ depends on includesmodule @
@@
- #include <linux/moduleparam.h>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_{info,get,put}_volsw instead of custom volume functions
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
[On N900]
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regmap instead of open-coding IO access and caching
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
[On N900]
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add tpa6130a2 controls by the component API and update rx51 accordingly
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec chip has a physical MUTE pin to let users control it via
GPIO. So this patch add a mute control support to the driver.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Both soc_compr_pointer and the platform driver pointer callback return
ints but current soc_compr_pointer always returns 0. Update this so we
return the actual value from the platform driver callback. This doesn't
fix any issues simply makes the code more consistent.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add multicore DSP support in Broxton DSP operations.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add multicore DSP support in Skylake DSP operations.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP can have more than one cores. In that case the secondary
core has to be managed by the driver. This patch adds the changes
to driver infrastructure to support multiple core.
A new object skl_dsp_cores is introduced to support multiple
core. Helpers skl_dsp_get_core() skl_dsp_put_core() help to
managed the cores.
Many of the power_up/down and DSP APIs take additional argument
of core_id. The primary core, 0 is always powered up first and
then on demand second core.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch fixes the issue that variable dereferenced before checking
'rt5514_dsp->substream'. Move the assignment to after the variable
checking of 'rt5514_dsp->substream'.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Noticed a style inconsistency in a comment, so update that
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We do not support async suspend due to dependency with rest of
card and require suspend/resume be executed synchronously, mark
the device accordingly.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 3513798ca4 ("ASoC: Intel: Add support for
PM ops in bxt-rt298") as the right way to fix this is to disable
async suspend
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds the control of MCLK that depends on the status of DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change file permissions of source files max9867.c/h from 0755 to 0644.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kconfig help texts were missing periods as suggested by Randy.
Also fix the alignment on a block of help text to be consistent
with rest.
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Randy reported following error when ACPI is not enabled:
warning: (SND_SOC_INTEL_BYTCR_RT5640_MACH && SND_SOC_INTEL_BYTCR_RT5651_MACH
&& SND_SOC_INTEL_CHT_BSW_RT5672_MACH && SND_SOC_INTEL_CHT_BSW_RT5645_MACH &&
SND_SOC_INTEL_CHT_BSW_MAX98090_TI_MACH) selects SND_SST_IPC_ACPI
+which has unmet direct dependencies (SOUND && !M68K && !UML && SND &&
SND_SOC && ACPI)
causing these build errors:
In file included from ../sound/soc/intel/atom/sst/sst_acpi.c:40:0:
../include/acpi/acpi_bus.h:65:20: error: conflicting types for
'acpi_evaluate_dsm'
union acpi_object *acpi_evaluate_dsm(acpi_handle handle, const u8 *uuid,
In file included from ../sound/soc/intel/atom/sst/sst_acpi.c:31:0:
../include/linux/acpi.h:676:34: note: previous definition of
'acpi_evaluate_dsm' was here
static inline union acpi_object *acpi_evaluate_dsm(acpi_handle handle,
CONFIG_SND_SST_IPC_ACPI was already dependent upon ACPI, but that was not
solving it. So move the depends up to machine drivers and remove from
CONFIG_SND_SST_IPC_ACPI.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch reorders the clearing of the DMA masks to avoid potential
artefacts being introduced.
Signed-off-by: Simon Trimmer <simont@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
reg-8a assign the tracking source for each ASRC tracker. The default
value is 0x0000 which means all ASRC trackers will track LRCK1. But
in most case, we wish each ASRC tracker track the corresponding LRCK.
i.e. ASRC1 tracks LRCK1, ASRC2 tracks LRCK2 and so on. So, we rewrite
reg-8a as 0x0123.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new PIO mode for the dwc audio driver causes a link failure
when it is built as a loadable module but the audio driver is built-in:
sound/built-in.o: In function `i2s_irq_handler':
:(.text+0x58c64): undefined reference to `dw_pcm_push_tx'
sound/built-in.o: In function `dw_i2s_probe':
:(.text+0x593dc): undefined reference to `dw_pcm_register'
We could link both into a single module, but apparently the
author intended them to be separate, so this instead changes
the Makefile to force the pcm module to be built-in if the
base module is. This is a bit hacky but not as bad as trying
to work around it in Kconfig language.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 79361b2b98 ("ASoC: dwc: Add PIO PCM extension")
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is using the set_bias_level to control the power on and
off so it should get SND_SOC_BIAS_OFF in order to proceed normal
powering sequences. This patch enables the idle_bias_off option so
the DAPM core will set the bias level to SND_SOC_BIAS_OFF instead
of stopping at SND_SOC_BIAS_STANDBY.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/cs53l30.c:182:20: warning:
symbol 'input1_sel_values' was not declared. Should it be static?
sound/soc/codecs/cs53l30.c:202:20: warning:
symbol 'input2_sel_values' was not declared. Should it be static?
sound/soc/codecs/cs53l30.c:734:20: warning:
symbol 'cs53l30_src_rates' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/max9860.c:120:28: warning:
symbol 'max9860_regmap' was not declared. Should it be static?
sound/soc/codecs/max9860.c:596:25: warning:
symbol 'max9860_pm_ops' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 79901317ce ("n_tty: Don't flush buffer when closing ldisc"),
introduced in v3.10, revealed a bug in the cx20442 codec driver
which has never been setting tty->receive_room on line discipline
open as it should from the beginning. Fix it.
Created and tested on Amstrad Delta against Linux-4.7-rc3
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the suspend callback to accompany the existing resume operation.
With the suspend/resume callbacks the regmap (regcache) state handling
can follow the recommended sequence.
Based on commit a2ebd58627 ("ASoC: ak4642: Implement suspend
callback") by Peter Ujfalusi <peter.ujfalusi@ti.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
During system resume:
kernel BUG at drivers/base/regmap/regcache.c:347!
...
PC is at regcache_sync+0x1c/0x128
LR is at ak4613_resume+0x28/0x34
The ak4613 driver is using a regmap cache sync to restore the
configuration of the chip on resume but does not actually define a
register cache which means that the resume is never going to work and we
trigger asserts in regmap. Fix this by enabling caching.
Based on commit d3030d1196 ("ASoC: ak4642: Enable cache usage to
fix crashes on resume") by Mark Brown <broonie@kernel.org>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8940 driver is using a regmap cache sync to restore the
configuration of the chip when switching from OFF to STANDBY, but does
not actually define a register cache which means that the restore is
never going to work and we trigger asserts in regmap. Fix this by
enabling caching.
Based on commit d3030d1196 ("ASoC: ak4642: Enable cache usage to
fix crashes on resume") by Mark Brown <broonie@kernel.org>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds 32 bit word capability to the wm8731 driver. The wm8731
codec is capable of handling 32 bit word sizes, however that has not
previously been activated in the codec driver.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I just added an I2C dependency to the wm8985 driver to work around
a build failure, but it turns out that was premature: we actually
need to depend on SND_SOC_I2C_AND_SPI, as the driver can work with either
of the two, and we only need to prevent a configuration that has
I2C=m and SND_SOC_WM8985=y.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 05252513fb ("ASoC: wm8985: add i2c dependency")
Signed-off-by: Mark Brown <broonie@kernel.org>
The devices from the ADAU17X1 family all have a MCLK clock input which
supplies the master clock for the device. The master clock is used as the
input clock for the PLL. Currently the MCLK rate as well as the desired PLL
output frequency need to be supplied by calling snd_soc_dai_set_pll() form
a machine driver.
Add support for specifying the MCLK using the common clock framework. In
addition to that also automatically configure the PLL to a suitable rate
if the master clock was provided using the CCW. This allows to use the
CODEC driver without any special configuration requirements from the
machine driver.
While the PLL output frequency can be configured over a (more or less)
continuous range the narrowness of the range and the other constraints of
the clocking tree usually only result in two output frequencies that will
actually be chosen. One for 44.1kHz based rates and one for 48kHz based
rates, these are the rates that the automatic PLL configuration will use.
For the rare case where a non-standard setup is required a machine driver
can disable the auto-configuration and configure a custom frequency using
the existing mechanisms.
If the common clock framework is not enabled clk_get() will return NULL and
the driver will function as before and the clock rate needs to be
configured manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Disabling the SGTL5000 through regulators would certainly save more
power than simply disabling the reference voltages as described in the
data sheet, but won't properly restore things on resume.
This driver does not support active regulators. So we simply disable the
reference bias currents.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To handle the soft reboot case, the internal PLL must be
disabled in SGTL5000_CHIP_CLK_CTRL before clearing bits
SGTL5000_VCOAMP_POWERUP and SGTL5000_PLL_POWERUP in
register SGTL5000_CHIP_ANA_POWER.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize CHIP_ANA_POWER to match power on defaults, which disables
ADC, DAC, and charge pumps.
In the process, remove references to the following register/bitfields
from the sgtl5000_set_power_regs routine:
CHIP_ANA_POWER/LINREG_SIMPLE_POWERUP and
CHIP_LINREG_CTRL/LINREG_VDD_MASK
And remove CHIP_ANA_POWER and CHIP_LINREG_CTRL from the set of default
registers so they don't get clobbered by sgtl5000_fill_defaults().
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If an error occurs writing defaults, produce an error message but
continue writing other registers. The failure of a single write should
not cause catastrophic device failure.
In at least one occurrence, I2C writes of CHIP_ANA_POWER were nacked,
though continuing allowed the device to operate properly.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator support on SGTL5000 is broken because the VDDIO and
VDDA and VDDD should be powered on before enabling MCLK as
shown in Figure 4 of [1]. This requires moving control of the
regulators from the codec block to the I2C block of the driver.
The bulk of this patch consists of swapping the codec device with
the i2c client. The new field num_supplies in struct sgtl5000_priv
is used instead of ARRAY_SIZE(supplies) to handle the special case
when the internal LDO is used instead of external VDDD.
Note that ER1 in the SGTL5000 Errata document [2] suggests that
all designs should use external VDDD.
Since the internal LDO can only be enabled after I2C is available,
there's no benefit in treating it as a regulator, so this patch
removes the regulator structure surrounding it.
Instead, a single block of code in sgtl5000_i2c_probe() performs
the initialization sequence in section 2.2.1.1 of [3] and page
26 of [1].
References:
[1] SGTL5000 data sheet
http://cache.nxp.com/files/analog/doc/data_sheet/SGTL5000.pdf
[2] SGTL5000 errata
http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf
[3] SGTL5000 Initialization and programming app note
http://cache.nxp.com/files/analog/doc/app_note/AN3663.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All new designs should use external VDDD according to official
documentation. See ER1 in errata sheet:
http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In is_connected_ep, when custom_stop_condition is true, need to
return the correct paths instead of con which is 0.
Fixes: 6742064aef7f('ASoC: dapm: support user-defined stop condition in dai_get_connected_widgets')
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While clearing loaded module count, we should check first to see
if module list is NULL or not. Some distributions can ship with
no modules and thus list can be empty.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module list was not initialized for Broxton DSP code, so
initialize it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need card to be early suspended and late resumed, so use prepare and
complete for card suspend and resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown
Markus Elfring
Vedang Patel
Sylwester Nawrocki
Nicolin Chen
Chris Zhong
Kuninori Morimoto
John Hsu
PC Liao
Wei Yongjun
Ben Zhang
Vinod Koul
Senthilnathan Veppur
Axel Lin
Arnd Bergmann
Kalle Kankare
Shreyas NC
Alan Cox
Takashi Iwai
Dharageswari R
Bard Liao
Peter Meerwald
Dan Carpenter
Subhransu S. Prusty
Garlic Tseng
Dave Airlie
Wei Yongjun
Amitoj Kaur Chawla
kbuild test robot
Maxime Ripard
Alexander Shiyan
Colin Ian King
kbuild test robot
Paul Handrigan
Adam Thomson
Helen Koike
Charles Keepax
Jayachandran B
Oder Chiou
Enric Balletbo i Serra
Simon Trimmer
Janusz Krzysztofik
Geert Uytterhoeven
Matt Flax
Lars-Peter Clausen
Eric Nelson
Clemens Gruber
Jeeja KP