ab5bd5cbc8 introduced the following
bug in linear software raid for large arrays on 32 bit machines:
which_dev() computes the device holding a given sector by shifting
down the sector number to a 32 bit range, dividing by the array
spacing and looking up the resulting index in the hash table of
the array.
Because the computed index might be slightly too small, a loop at
the end of which_dev() increases the index until the given sector
actually falls into the range of the device associated with that index.
The changes of the above mentioned commit caused this loop to check
whether the _index_ rather than the sector number is small enough,
effectively bypassing the loop and thus possibly returning the wrong
device.
As reported by Simon Kirby, this leads to errors such as
linear_make_request: Sector 2340486136 out of bounds on dev sdi: 156301312 sectors, offset 2109870464
Fix this bug by introducing a local variable for the index so that
the variable containing the passed sector is left unchanged.
Cc: stable@kernel.org
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
If a raid1 only has a single working device and gets a read error,
we choose to simply return that error up to the filesystem (or whatever)
rather than failing the whole array.
However the codes doesn't quite do that. We attempt a readbalance
which allocates the same drive, so we retry the read - indefinitely.
Instead: If read_balance in the error case chooses the same drive that just
failed, treat it as a failure and don't retry.
Signed-off-by: NeilBrown <neilb@suse.de>
Prevent kprobes from catching spurious faults which will cause infinite
recursive page-fault and memory corruption by stack overflow.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... and yes, gcc is insane enough to eat that without complaint.
We probably want sparse to scream on those...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
Revert "configfs: Silence lockdep on mkdir(), rmdir() and configfs_depend_item()"
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix up T-bit error handling in SH-4A mutex fastpath.
sh: Fix up spurious syscall restarting.
sh: fcnvds fix with denormalized numbers on SH-4 FPU.
sh: Only reserve memory under CONFIG_ZERO_PAGE_OFFSET when it != 0.
sh: Handle calling csum_partial with misaligned data
sh: ap325rxa: Enable ov772x in defconfig.
sh: ap325rxa: Add ov772x support.
sh: ap325rxa: control camera power toggling.
sh: mach-migor: Enable ov772x and tw9910 in defconfig.
As the options passed to ip6_append_data may be ephemeral, we need
to duplicate it for corking. This patch applies the simplest fix
which is to memdup all the relevant bits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP header pointer assignment must happen after calling
pskb_may_pull(). As pskb_may_pull() can potentially alter the SKB
buffer.
This was exposted by running multicast traffic through the NIU driver,
as it won't prepull the protocol headers into the linear area on
receive.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
lseek() further than length of the file will leave stale ->index
(second-to-last during iteration). Next seq_read() will not notice
that ->f_pos is big enough to return 0, but will print last item
as if ->f_pos is pointing to it.
Introduced in commit cb510b8172
aka "seq_file: more atomicity in traverse()".
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In 2.6.25 some /proc files were converted to use the seq_file
infrastructure. But seq_files do not correctly support pread(), which
broke some usersapce applications.
To handle pread correctly we can't assume that f_pos is where we left it
in seq_read. So move traverse() so that we can eventually use it in
seq_read and do thus some day support pread().
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Cc: Paul Turner <pjt@google.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A missing type cast results in writing way beyond the end of a kzalloc()'d
memory segment resulting in slab corruption. But it seems like the better
solution is to define ->recv_msg_slots as a 'void *' rather than a
'struct xpc_notify_mq_msg_uv *' and add the type cast.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do usual do {} while (0) dance, otherwise
fs/gfs2/util.c:99: error: expected expression before 'else'
drivers/scsi/lpfc/lpfc_sli.c:363: error: expected expression before 'else'
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we return directly with -EPERM then lock_kernel() is still held.
This was found with a code checker (http://repo.or.cz/w/smatch.git/).
[akpm@linux-foundation.org: fix another such path - missed func_exit()]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: <R.E.Wolff@BitWizard.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix namespace violations by changing non-kconfig CONFIG_ names to CNFG_*.
Fixes breakage in staging/, which adds a real CONFIG_PANEL.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently both da903x backlight and voltage reulator drivers have the
same name. Rename the backlight driver to allow use of both drivers as
modules.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ssc pointer is not valid when the id is not found in the list.
Convert the message from a debug one into an error message and avoid
dereferencing the bad pointer.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix do_wp_page for VM_MIXEDMAP mappings.
In the case where pfn_valid returns 0 for a pfn at the beginning of
do_wp_page and the mapping is not shared writable, the code branches to
label `gotten:' with old_page == NULL.
In case the vma is locked (vma->vm_flags & VM_LOCKED), lock_page,
clear_page_mlock, and unlock_page try to access the old_page.
This patch checks whether old_page is valid before it is dereferenced.
The regression was introduced by "mlock: mlocked pages are unevictable"
(commit b291f00039).
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With exclusive waiters, every process woken up through the wait queue must
ensure that the next waiter down the line is woken when it has finished.
Interruptible waiters don't do that when aborting due to a signal. And if
an aborting waiter is concurrently woken up through the waitqueue, noone
will ever wake up the next waiter.
This has been observed with __wait_on_bit_lock() used by
lock_page_killable(): the first contender on the queue was aborting when
the actual lock holder woke it up concurrently. The aborted contender
didn't acquire the lock and therefor never did an unlock followed by
waking up the next waiter.
Add abort_exclusive_wait() which removes the process' wait descriptor from
the waitqueue, iff still queued, or wakes up the next waiter otherwise.
It does so under the waitqueue lock. Racing with a wake up means the
aborting process is either already woken (removed from the queue) and will
wake up the next waiter, or it will remove itself from the queue and the
concurrent wake up will apply to the next waiter after it.
Use abort_exclusive_wait() in __wait_event_interruptible_exclusive() and
__wait_on_bit_lock() when they were interrupted by other means than a wake
up through the queue.
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Mentored-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Chuck Lever <cel@citi.umich.edu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org> ["after some testing"]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I got the "list is moderated message," so add it here.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6710x for having correctly setup
axes.
Signed-off-by: Martin Kebert <gkmarty@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6730x for having correctly setup
axes.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6530x for having correctly setup
axes.
Reported-by: Jerome Poulin <jeromepoulin@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to dmesg my laptop model HP 6510b is not being recognized by this
driver. After I have modified "lis3lv02d.c" axes in Neverball are OK.
Signed-off-by: Jiri Tersel <tersel@mail.muni.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error-path code can call rfkill_unregister() with a pointer which does
not contain the result of a call to rfkill_register(). It goes BUG().
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12560.
Cc: Frans Pop <elendil@planet.nl>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Matthew Garrett <mjg@redhat.com>
Reported-by: Helge Deller <deller@gmx.de>
Testted-by: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 0c2d64fb6c because it causes
(arguably poorly designed) existing userspace to spend interminable
periods closing billions of not-open file descriptors.
We could bring this back, with some sort of opt-in tunable in /proc, which
defaults to "off".
Peter's alanysis follows:
: I spent several hours trying to get to the bottom of a serious
: performance issue that appeared on one of our servers after upgrading to
: 2.6.28. In the end it's what could be considered a userspace bug that
: was triggered by a change in 2.6.28. Since this might also affect other
: people I figured I'd at least document what I found here, and maybe we
: can even do something about it:
:
:
: So, I upgraded some of debian.org's machines to 2.6.28.1 and immediately
: the team maintaining our ftp archive complained that one of their
: scripts that previously ran in a few minutes still hadn't even come
: close to being done after an hour or so. Downgrading to 2.6.27 fixed
: that.
:
: Turns out that script is forking a lot and something in it or python or
: whereever closes all the file descriptors it doesn't want to pass on.
: That is, it starts at zero and goes up to ulimit -n/RLIMIT_NOFILE and
: closes them all with a few exceptions.
:
: Turns out that takes a long time when your limit -n is now 2^20 (1048576).
:
: With 2.6.27.* the ulimit -n was the standard 1024, but with 2.6.28 it is
: now a thousand times that.
:
: 2.6.28 included a patch titled "rlimit: permit setting RLIMIT_NOFILE to
: RLIM_INFINITY" (0c2d64fb6c)[1] that
: allows, as the title implies, to set the limit for number of files to
: infinity.
:
: Closer investigation showed that the broken default ulimit did not apply
: to "system" processes (like stuff started from init). In the end I
: could establish that all processes that passed through pam_limit at one
: point had the bad resource limit.
:
: Apparently the pam library in Debian etch (4.0) initializes the limits
: to some default values when it doesn't have any settings in limit.conf
: to override them. Turns out that for nofiles this is RLIM_INFINITY.
: Commenting out "case RLIMIT_NOFILE" in pam_limit.c:267 of our pam
: package version 0.79-5 fixes that - tho I'm not sure what side effects
: that has.
:
: Debian lenny (the upcoming 5.0 version) doesn't have this issue as it
: uses a different pam (version).
Reported-by: Peter Palfrader <weasel@debian.org>
Cc: Adam Tkac <vonsch@gmail.com>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
shm_get_stat() assumes that the inode is a "struct shmem_inode_info",
which is incorrect for !CONFIG_SHMEM (see fs/ramfs/inode.c:
ramfs_get_inode() vs. mm/shmem.c: shmem_get_inode()).
This bad assumption can cause shmctl(SHM_INFO) to lockup when
shm_get_stat() tries to spin_lock(&info->lock). Users of !CONFIG_SHMEM
may encounter this lockup simply by invoking the 'ipcs' command.
Reported by Jiri Olsa back in February 2008:
http://lkml.org/lkml/2008/2/29/74
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Reported-by: Jiri Olsa <olsajiri@gmail.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: <stable@kernel.org> [2.6.everything]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid calling copy_from/to_user() with fb_info->lock mutex held in fbmem
ioctl().
fb_mmap() is called under mm->mmap_sem (A) held, that also acquires
fb_info->lock (B); fb_ioctl() takes fb_info->lock (B) and does
copy_from/to_user() that might acquire mm->mmap_sem (A), causing a
deadlock.
NOTE: it doesn't push down the fb_info->lock in each own driver's
fb_ioctl(), so there are still potential deadlocks elsewhere.
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Johannes Weiner <hannes@saeurebad.de>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple RTC driver for the MSP430 firmware on the DM355 EVM board. Other
than not supporting atomic reads/writes of all four bytes, this is
reasonable as a basic no-alarm RTC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dell-laptop makes use of the power supply class information to choose
which backlight interface to change. Add a depends on it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The swap() macro is accidentally retuning the value of its first argument.
Change it into a doesn't-return-anything macro before someone goes and
relies upon this behaviour.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The device can take a while to respond to an open/close request, so
increase the time kernel will wait for response (1 ms to 10ms).
Also, properly clean up a channel on a failed open, by calling the channel
close routine. Just freeing the memory isn't sufficient, the device needs
to be informed that the channel is no longer open, and the device memory
cleared of references to freed dma buffer.
Signed-off-by: David Altobelli <david.altobelli@hp.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha:
kernel/async.c: In function 'run_one_entry':
kernel/async.c:141: warning: format '%lli' expects type 'long long int', but argument 2 has type 'async_cookie_t'
kernel/async.c:149: warning: format '%lli' expects type 'long long int', but argument 2 has type 'async_cookie_t'
kernel/async.c:149: warning: format '%lld' expects type 'long long int', but argument 4 has type 's64'
kernel/async.c: In function 'async_synchronize_cookie_special':
kernel/async.c:250: warning: format '%lli' expects type 'long long int', but argument 3 has type 's64'
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some fixes regarding snd-hda-intel workqueue:
- Use create_singlethread_workqueue() instead of create_workqueue()
as per-CPU work isn't required.
- Allocate workq name string properly
- Renamed the workq name to "hd-audio*" to be more obvious.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SOFT_RESET must be asserted for at least 3 TX clocks in order for it to work
properly. The syncs in the gfar_write() commands have been hiding this, but
we need to guarantee it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BD_LENGTH_MASK is supposed to catch the low 16-bits of the status field, not
the low byte. The old way, we would never be able to clean up tx packets with
sizes divisible by 256.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LRO switch is always set to 1 in the rx processing loop.
It breaks the accelerated iSCSI receive traffic.
Fix its computation.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: APIC: enable workaround on AMD Fam10h CPUs
xen: disable interrupts before saving in percpu
x86: add x86@kernel.org to MAINTAINERS
x86: push old stack address on irqstack for unwinder
irq, x86: fix lock status with numa_migrate_irq_desc
x86: add cache descriptors for Intel Core i7
x86/Voyager: make it build and boot
Cleans uCode key table bit map iwl_clear_stations_table
since all stations are cleared also the key table must be.
Since the keys are not removed properly on suspend by mac80211
this may result in exhausting key table on resume leading
to memory corruption during removal
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 0e0333429a.
I committed this by accident - Joel and Louis are working with the lockdep
maintainer to provide a better solution than just turning lockdep off.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Acked-by: <Joel Becker <joel.becker@oracle.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: pcm_oss: AFMT_S24_LE is set twice in return value
ALSA: ASoC: email - update email addresses.
OMAP: ASoC: Fix spinlock misuse in omap-pcm.c
ALSA: hda - No widget selection for volume knob widgets in proc output
ALSA: hda - Add support of iMac 24 Aluminium
ALSA: alsa: time reaches -1, tested 0
ALSA: hda - Add quirk for another HP dv5 model
Andre Noll
NeilBrown
Masami Hiramatsu
Al Viro
Linus Torvalds
David S. Miller
Herbert Xu
Jesper Dangaard Brouer
Alexey Dobriyan
Eric Biederman
Dean Nelson
Dan Carpenter
Randy Dunlap
Manish Katiyar
Mike Rapoport
Hans-Christian Egtvedt
Carsten Otte
Johannes Weiner
Martin Kebert
Pavel Herrmann
Eric Piel
Jiri Tersel
Andrew Morton
Tony Battersby
Andrea Righi
David Brownell
Matthew Garrett
Peter Zijlstra
David Altobelli
Chris Mason
Takashi Iwai
Andy Fleming
Divy Le Ray
Reinette Chatre
Mark Fasheh