Don't send an IDLE ACK at the end of the transmission of the response to a
service call. The service end resends DATA packets until the client sends an
ACK that hard-acks all the send data. At that point, the call is complete.
Signed-off-by: David Howells <dhowells@redhat.com>
Set the timestamp on sk_buffs holding packets to be transmitted before
queueing them because the moment the packet is on the queue it can be seen
by the retransmission algorithm - which may see a completely random
timestamp.
If the retransmission algorithm sees such a timestamp, it may retransmit
the packet and, in future, tell the congestion management algorithm that
the retransmit timer expired.
Signed-off-by: David Howells <dhowells@redhat.com>
With TCP MTU probing enabled and offload TX checksumming disabled,
tcp_mtu_probe() calculated the wrong checksum when a fragment being copied
into the probe's SKB had an odd length. This was caused by the direct use
of skb_copy_and_csum_bits() to calculate the checksum, as it pads the
fragment being copied, if needed. When this fragment was not the last, a
subsequent call used the previous checksum without considering this
padding.
The effect was a stale connection in one way, as even retransmissions
wouldn't solve the problem, because the checksum was never recalculated for
the full SKB length.
Signed-off-by: Douglas Caetano dos Santos <douglascs@taghos.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the following patch can make FQ very precise, even in VM
or stressed hosts. It matters at high pacing rates.
We take into account the difference between the time that was programmed
when last packet was sent, and current time (a drift of tens of usecs is
often observed)
Add an EWMA of the unthrottle latency to help diagnostics.
This latency is the difference between current time and oldest packet in
delayed RB-tree. This accounts for the high resolution timer latency,
but can be different under stress, as fq_check_throttled() can be
opportunistically be called from a dequeue() called after an enqueue()
for a different flow.
Tested:
// Start a 10Gbit flow
$ netperf --google-pacing-rate 1250000000 -H lpaa24 -l 10000 -- -K bbr &
Before patch :
$ sar -n DEV 10 5 | grep eth0 | grep Average
Average: eth0 17106.04 756876.84 1102.75 1119049.02 0.00 0.00 0.52
After patch :
$ sar -n DEV 10 5 | grep eth0 | grep Average
Average: eth0 17867.00 800245.90 1151.77 1183172.12 0.00 0.00 0.52
A new iproute2 tc can output the 'unthrottle latency' :
$ tc -s qd sh dev eth0 | grep latency
0 gc, 0 highprio, 32490767 throttled, 2382 ns latency
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_acked() is using 32bit arithmetics on 16bits vars, via TSN_lte()
macros, which is weird and confusing.
Once the offset to ctsn is calculated, all wrapping is already handled
and thus to verify the Gap Ack blocks we can just use pure
less/big-or-equal than checks.
Also, rename gap variable to tsn_offset, so it's more meaningful, as
it doesn't point to any gap at all.
Even so, I don't think this discrepancy resulted in any practical bug.
This patch is a preparation for the next one, which will introduce
typecheck() for TSN_lte() macros and would cause a compile error here.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 2ccccf5fb4 ("net_sched: update hierarchical backlog too")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Stas Nichiporovich <stasn77@gmail.com>
Fixes: 2ccccf5fb4 ("net_sched: update hierarchical backlog too")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error path in route4_change(), 'f' could be NULL,
so we should check NULL before calling tcf_exts_destroy().
Fixes: b9a24bb76b ("net_sched: properly handle failure case of tcf_exts_init()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already checked for !found just a bit before:
if (!found) {
regs->verdict.code = NFT_BREAK;
return;
}
if (found && set->flags & NFT_SET_MAP)
^^^^^
So this redundant check can just go away.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It's better to use sizeof(info->name)-1 as index to force set the string
tail instead of literal number '29'.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There are some codes which are used to get one random once in netfilter.
We could use net_get_random_once to simplify these codes.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
pkt->xt.thoff is not always set properly, but we use it without any check.
For payload expr, it will cause wrong results. For nftrace, we may notify
the wrong network or transport header to the user space, furthermore,
input the following nft rules, warning message will be printed out:
# nft add rule arp filter output meta nftrace set 1
WARNING: CPU: 0 PID: 13428 at net/netfilter/nf_tables_trace.c:263
nft_trace_notify+0x4a3/0x5e0 [nf_tables]
Call Trace:
[<ffffffff813d58ae>] dump_stack+0x63/0x85
[<ffffffff810a4c0b>] __warn+0xcb/0xf0
[<ffffffff810a4d3d>] warn_slowpath_null+0x1d/0x20
[<ffffffffa0589703>] nft_trace_notify+0x4a3/0x5e0 [nf_tables]
[ ... ]
[<ffffffffa05690a8>] nft_do_chain_arp+0x78/0x90 [nf_tables_arp]
[<ffffffff816f4aa2>] nf_iterate+0x62/0x80
[<ffffffff816f4b33>] nf_hook_slow+0x73/0xd0
[<ffffffff81732bbf>] arp_xmit+0x8f/0xb0
[ ... ]
[<ffffffff81732d36>] arp_solicit+0x106/0x2c0
So before we use pkt->xt.thoff, check the tprot_set first.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There's an off-by-one issue in nft_payload_fast_eval, skb_tail_pointer
and ptr + priv->len all point to the last valid address plus 1. So if
they are equal, we can still fetch the valid data. It's unnecessary to
fall back to nft_payload_eval.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, the user can specify the queue numbers by _QUEUE_NUM and
_QUEUE_TOTAL attributes, this is enough in most situations.
But acctually, it is not very flexible, for example:
tcp dport 80 mapped to queue0
tcp dport 81 mapped to queue1
tcp dport 82 mapped to queue2
In order to do this thing, we must add 3 nft rules, and more
mapping meant more rules ...
So take one register to select the queue number, then we can add one
simple rule to mapping queues, maybe like this:
queue num tcp dport map { 80:0, 81:1, 82:2 ... }
Florian Westphal also proposed wider usage scenarios:
queue num jhash ip saddr . ip daddr mod ...
queue num meta cpu ...
queue num meta mark ...
The last point is how to load a queue number from sreg, although we can
use *(u16*)®s->data[reg] to load the queue number, just like nat expr
to load its l4port do.
But we will cooperate with hash expr, meta cpu, meta mark expr and so on.
They all store the result to u32 type, so cast it to u16 pointer and
dereference it will generate wrong result in the big endian system.
So just keep it simple, we treat queue number as u32 type, although u16
type is already enough.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fetch value and validate u32 netlink attribute. This validation is
usually required when the u32 netlink attributes are being stored in a
field whose size is smaller.
This patch revisits 4da449ae1d ("netfilter: nft_exthdr: Add size check
on u8 nft_exthdr attributes").
Fixes: 96518518cc ("netfilter: add nftables")
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
From: Andrey Vagin <avagin@openvz.org>
Each namespace has an owning user namespace and now there is not way
to discover these relationships.
Pid and user namepaces are hierarchical. There is no way to discover
parent-child relationships too.
Why we may want to know relationships between namespaces?
One use would be visualization, in order to understand the running
system. Another would be to answer the question: what capability does
process X have to perform operations on a resource governed by namespace
Y?
One more use-case (which usually called abnormal) is checkpoint/restart.
In CRIU we are going to dump and restore nested namespaces.
There [1] was a discussion about which interface to choose to determing
relationships between namespaces.
Eric suggested to add two ioctl-s [2]:
> Grumble, Grumble. I think this may actually a case for creating ioctls
> for these two cases. Now that random nsfs file descriptors are bind
> mountable the original reason for using proc files is not as pressing.
>
> One ioctl for the user namespace that owns a file descriptor.
> One ioctl for the parent namespace of a namespace file descriptor.
Here is an implementaions of these ioctl-s.
$ man man7/namespaces.7
...
Since Linux 4.X, the following ioctl(2) calls are supported for
namespace file descriptors. The correct syntax is:
fd = ioctl(ns_fd, ioctl_type);
where ioctl_type is one of the following:
NS_GET_USERNS
Returns a file descriptor that refers to an owning user names‐
pace.
NS_GET_PARENT
Returns a file descriptor that refers to a parent namespace.
This ioctl(2) can be used for pid and user namespaces. For
user namespaces, NS_GET_PARENT and NS_GET_USERNS have the same
meaning.
In addition to generic ioctl(2) errors, the following specific ones
can occur:
EINVAL NS_GET_PARENT was called for a nonhierarchical namespace.
EPERM The requested namespace is outside of the current namespace
scope.
[1] https://lkml.org/lkml/2016/7/6/158
[2] https://lkml.org/lkml/2016/7/9/101
Changes for v2:
* don't return ENOENT for init_user_ns and init_pid_ns. There is nothing
outside of the init namespace, so we can return EPERM in this case too.
> The fewer special cases the easier the code is to get
> correct, and the easier it is to read. // Eric
Changes for v3:
* rename ns->get_owner() to ns->owner(). get_* usually means that it
grabs a reference.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: "W. Trevor King" <wking@tremily.us>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Return -EPERM if an owning user namespace is outside of a process
current user namespace.
v2: In a first version ns_get_owner returned ENOENT for init_user_ns.
This special cases was removed from this version. There is nothing
outside of init_user_ns, so we can return EPERM.
v3: rename ns->get_owner() to ns->owner(). get_* usually means that it
grabs a reference.
Acked-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Use xdr->nwords to tell us how much buffer remains.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When we copy the first part of the data, we need to ensure that value
of xdr->nwords is updated as well. Do so by calling __xdr_inline_decode()
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The current error codes returned when a the per user per user
namespace limit are hit (EINVAL, EUSERS, and ENFILE) are wrong. I
asked for advice on linux-api and it we made clear that those were
the wrong error code, but a correct effor code was not suggested.
The best general error code I have found for hitting a resource limit
is ENOSPC. It is not perfect but as it is unambiguous it will serve
until someone comes up with a better error code.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Pull networking fixes from David Miller:
"Mostly small bits scattered all over the place, which is usually how
things go this late in the -rc series.
1) Proper driver init device resets in bnx2, from Baoquan He.
2) Fix accounting overflow in __tcp_retransmit_skb(),
sk_forward_alloc, and ip_idents_reserve, from Eric Dumazet.
3) Fix crash in bna driver ethtool stats handling, from Ivan Vecera.
4) Missing check of skb_linearize() return value in mac80211, from
Johannes Berg.
5) Endianness fix in nf_table_trace dumps, from Liping Zhang.
6) SSN comparison fix in SCTP, from Marcelo Ricardo Leitner.
7) Update DSA and b44 MAINTAINERS entries.
8) Make input path of vti6 driver work again, from Nicolas Dichtel.
9) Off-by-one in mlx4, from Sebastian Ott.
10) Fix fallback route lookup handling in ipv6, from Vincent Bernat.
11) Fix stack corruption on probe in qed driver, from Yuval Mintz.
12) PHY init fixes in r8152 from Hayes Wang.
13) Missing SKB free in irda_accept error path, from Phil Turnbull"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tcp: properly account Fast Open SYN-ACK retrans
tcp: fix under-accounting retransmit SNMP counters
MAINTAINERS: Update b44 maintainer.
net: get rid of an signed integer overflow in ip_idents_reserve()
net/mlx4_core: Fix to clean devlink resources
net: can: ifi: Configure transmitter delay
vti6: fix input path
ipmr, ip6mr: return lastuse relative to now
r8152: disable ALDPS and EEE before setting PHY
r8152: remove r8153_enable_eee
r8152: move PHY settings to hw_phy_cfg
r8152: move enabling PHY
r8152: move some functions
cxgb4/cxgb4vf: Allocate more queues for 25G and 100G adapter
qed: Fix stack corruption on probe
MAINTAINERS: Add an entry for the core network DSA code
net: ipv6: fallback to full lookup if table lookup is unsuitable
net/mlx5: E-Switch, Handle mode change failures
net/mlx5: E-Switch, Fix error flow in the SRIOV e-switch init code
net/mlx5: Fix flow counter bulk command out mailbox allocation
...
Scan response data should not be updated unless there
is an advertising instance.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support of an offset value for incremental counter and random. With
this option the sysadmin is able to start the counter to a certain value
and then apply the generated number.
Example:
meta mark set numgen inc mod 2 offset 100
This will generate marks with the serie 100, 101, 100, 101, ...
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-----BEGIN PGP SIGNATURE-----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=3zfm
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160922-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Preparation for slow-start algorithm [ver #2]
Here are some patches that prepare for improvements in ACK generation and
for the implementation of the slow-start part of the protocol:
(1) Stop storing the protocol header in the Tx socket buffers, but rather
generate it on the fly. This potentially saves a little space and
makes it easier to alter the header just before transmission (the
flags may get altered and the serial number has to be changed).
(2) Mask off the Tx buffer annotations and add a flag to record which ones
have already been resent.
(3) Track RTT on a per-peer basis for use in future changes. Tracepoints
are added to log this.
(4) Send PING ACKs in response to incoming calls to elicit a PING-RESPONSE
ACK from which RTT data can be calculated. The response also carries
other useful information.
(5) Expedite PING-RESPONSE ACK generation from sendmsg. If we're actively
using sendmsg, this allows us, under some circumstances, to avoid
having to rely on the background work item to run to generate this
ACK.
This requires ktime_sub_ms() to be added.
(6) Set the REQUEST-ACK flag on some DATA packets to elicit ACK-REQUESTED
ACKs from which RTT data can be calculated.
(7) Limit the use of pings and ACK requests for RTT determination.
Changes:
(V2) Don't use the C division operator for 64-bit division. One instance
should use do_div() and the other should be using nsecs_to_jiffies().
The last two patches got transposed, leading to an undefined symbol
in one of them.
Reported-by: kbuild test robot <lkp@intel.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't want to send a PING ACK for every new incoming call as that just
adds to the network traffic. Instead, we send a PING ACK to the first
three that we receive and then once per second thereafter.
This could probably be made adjustable in future.
Signed-off-by: David Howells <dhowells@redhat.com>
Reduce the number of ACK-Requests we set on DATA packets that we're sending
to reduce network traffic. We set the flag on odd-numbered DATA packets to
start off the RTT cache until we have at least three entries in it and then
probe once per second thereafter to keep it topped up.
This could be made tunable in future.
Note that from this point, the RXRPC_REQUEST_ACK flag is set on DATA
packets as we transmit them and not stored statically in the sk_buff.
Signed-off-by: David Howells <dhowells@redhat.com>
Since the TFO socket is accepted right off SYN-data, the socket
owner can call getsockopt(TCP_INFO) to collect ongoing SYN-ACK
retransmission or timeout stats (i.e., tcpi_total_retrans,
tcpi_retransmits). Currently those stats are only updated
upon handshake completes. This patch fixes it.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes these under-accounting SNMP rtx stats
LINUX_MIB_TCPFORWARDRETRANS
LINUX_MIB_TCPFASTRETRANS
LINUX_MIB_TCPSLOWSTARTRETRANS
when retransmitting TSO packets
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to sending a PING ACK to gain RTT data, we can set the
RXRPC_REQUEST_ACK flag on a DATA packet and get a REQUESTED-ACK ACK. The
ACK packet contains the serial number of the packet it is in response to,
so we can look through the Tx buffer for a matching DATA packet.
This requires that the data packets be stamped with the time of
transmission as a ktime rather than having the resend_at time in jiffies.
This further requires the resend code to do the resend determination in
ktimes and convert to jiffies to set the timer.
Signed-off-by: David Howells <dhowells@redhat.com>
Expedite the transmission of a response to a PING ACK by sending it from
sendmsg if one is pending. We're most likely to see a PING ACK during the
client call Tx phase as the other side may use it to determine a number of
parameters, such as the client's receive window size, the RTT and whether
the client is doing slow start (similar to RFC5681).
If we don't expedite it, it's left to the background processing thread to
transmit.
Signed-off-by: David Howells <dhowells@redhat.com>
Send a PING ACK packet to the peer when we get a new incoming call from a
peer we don't have a record for. The PING RESPONSE ACK packet will tell us
the following about the peer:
(1) its receive window size
(2) its MTU sizes
(3) its support for jumbo DATA packets
(4) if it supports slow start (similar to RFC 5681)
(5) an estimate of the RTT
This is necessary because the peer won't normally send us an ACK until it
gets to the Rx phase and we send it a packet, but we would like to know
some of this information before we start sending packets.
A pair of tracepoints are added so that RTT determination can be observed.
Signed-off-by: David Howells <dhowells@redhat.com>
And avoid the usage of '&~3'. This is the last place still not using
the macro.
Also break the line to make it easier to read.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To something more meaningful these days, specially because this is
working on packet headers or lengths and which are not tied to any CPU
arch but to the protocol itself.
So, WORD_TRUNC becomes SCTP_TRUNC4 and WORD_ROUND becomes SCTP_PAD4.
Reported-by: David Laight <David.Laight@ACULAB.COM>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2016-09-21
1) Propagate errors on security context allocation.
From Mathias Krause.
2) Fix inbound policy checks for inter address family tunnels.
From Thomas Zeitlhofer.
3) Fix an old memory leak on aead algorithm usage.
From Ilan Tayari.
4) A recent patch fixed a possible NULL pointer dereference
but broke the vti6 input path.
Fix from Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We saw sch_fq drops caused by the per flow limit of 100 packets and TCP
when dealing with large cwnd and bursts of retransmits.
Even after increasing the limit to 1000, and even after commit
10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time"),
we can still have these drops.
Under certain conditions, TCP can spend a considerable amount of
time queuing thousands of skbs in a single tcp_xmit_retransmit_queue()
invocation, incurring latency spikes and stalls of other softirq
handlers.
This patch implements TSQ for retransmits, limiting number of packets
and giving more chance for scheduling packets in both ways.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko reported an UBSAN warning happening in ip_idents_reserve()
[] UBSAN: Undefined behaviour in ./arch/x86/include/asm/atomic.h:156:11
[] signed integer overflow:
[] -2117905507 + -695755206 cannot be represented in type 'int'
Since we do not have uatomic_add_return() yet, use atomic_cmpxchg()
so that the arithmetics can be done using unsigned int.
Fixes: 04ca6973f7 ("ip: make IP identifiers less predictable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 'skb_vlan_pop' to use eth_type_vlan instead of directly comparing
skb->protocol to ETH_P_8021Q or ETH_P_8021AD.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 93515d53b1
"net: move vlan pop/push functions into common code"
skb_vlan_pop was moved from its private location in openvswitch to
skbuff common code.
In case skb has non hw-accel vlan tag, the original 'pop_vlan()' assured
that skb->len is sufficient (if skb->len < VLAN_ETH_HLEN then pop was
considered a no-op).
This validation was moved as is into the new common 'skb_vlan_pop'.
Alas, in its original location (openvswitch), there was a guarantee that
'data' points to the mac_header, therefore the 'skb->len < VLAN_ETH_HLEN'
condition made sense.
However there's no such guarantee in the generic 'skb_vlan_pop'.
For short packets received in rx path going through 'skb_vlan_pop',
this causes 'skb_vlan_pop' to fail pop-ing a valid vlan hdr (in the non
hw-accel case) or to fail moving next tag into hw-accel tag.
Remove the 'skb->len < VLAN_ETH_HLEN' condition entirely:
It is superfluous since inner '__skb_vlan_pop' already verifies there
are VLAN_ETH_HLEN writable bytes at the mac_header.
Note this presents a slight change to skb_vlan_pop() users:
In case total length is smaller than VLAN_ETH_HLEN, skb_vlan_pop() now
returns an error, as opposed to previous "no-op" behavior.
Existing callers (e.g. tc act vlan, ovs) usually drop the packet if
'skb_vlan_pop' fails.
Fixes: 93515d53b1 ("net: move vlan pop/push functions into common code")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Pravin Shelar <pshelar@ovn.org>
Reviewed-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCA_VLAN_ACT_MODIFY allows one to change an existing tag.
It accepts same attributes as TCA_VLAN_ACT_PUSH (protocol, id,
priority).
If packet is vlan tagged, then the tag gets overwritten according to
user specified attributes.
For example, this allows user to replace a tag's vid while preserving
its priority bits (as opposed to "action vlan pop pipe action vlan push").
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This exports the functionality of extracting the tag from the payload,
without moving next vlan tag into hw accel tag.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to track the average RTT for a peer. Sources of RTT data
will be added in subsequent patches.
The RTT data will be useful in the future for determining resend timeouts
and for handling the slow-start part of the Rx protocol.
Also add a pair of tracepoints, one to log transmissions to elicit a
response for RTT purposes and one to log responses that contribute RTT
data.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a Tx-phase annotation for packet buffers to indicate that a buffer has
already been retransmitted. This will be used by future congestion
management. Re-retransmissions of a packet don't affect the congestion
window managment in the same way as initial retransmissions.
Signed-off-by: David Howells <dhowells@redhat.com>
Don't store the rxrpc protocol header in sk_buffs on the transmit queue,
but rather generate it on the fly and pass it to kernel_sendmsg() as a
separate iov. This reduces the amount of storage required.
Note that the security header is still stored in the sk_buff as it may get
encrypted along with the data (and doesn't change with each transmission).
Signed-off-by: David Howells <dhowells@redhat.com>
Implement .stats_update() callback. The implementation
is generic and can be reused by other simple actions if
needed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call into offloaded filters to update stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cls_bpf support for the TCA_CLS_FLAGS_SKIP_SW flag.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cls_bpf support for the TCA_CLS_FLAGS_SKIP_HW flag.
Unlike U32 and flower cls_bpf already has some netlink
flags defined. Create a new attribute to be able to use
the same flag values as the above.
Unlike U32 and flower reject unknown flags.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware offload capability to cls_bpf classifier,
similar to what have been done with U32 and flower.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is called from the packet input path, we get lock contention
if many cpus handle ipsec in parallel.
After recent rcu conversion it is safe to call __xfrm_state_lookup
without the spinlock.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Since commit 1625f45299, vti6 is broken, all input packets are dropped
(LINUX_MIB_XFRMINNOSTATES is incremented).
XFRM_TUNNEL_SKB_CB(skb)->tunnel.ip6 is set by vti6_rcv() before calling
xfrm6_rcv()/xfrm6_rcv_spi(), thus we cannot set to NULL that value in
xfrm6_rcv_spi().
A new function xfrm6_rcv_tnl() that enables to pass a value to
xfrm6_rcv_spi() is added, so that xfrm6_rcv() is not touched (this function
is used in several handlers).
CC: Alexey Kodanev <alexey.kodanev@oracle.com>
Fixes: 1625f45299 ("net/xfrm_input: fix possible NULL deref of tunnel.ip6->parms.i_key")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When I introduced the lastuse member I made a subtle error because it was
returned as an absolute value but that is meaningless to user-space as it
doesn't allow to see how old exactly an entry is. Let's make it similar to
how the bridge returns such values and make it relative to "now" (jiffies).
This allows us to show the actual age of the entries and is much more
useful (e.g. user-space daemons can age out entries, iproute2 can display
the lastuse properly).
Fixes: 43b9e12740 ("net: ipmr/ip6mr: add support for keeping an entry age")
Reported-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements a new TCP congestion control algorithm: BBR
(Bottleneck Bandwidth and RTT). A detailed description of BBR will be
published in ACM Queue, Vol. 14 No. 5, September-October 2016, as
"BBR: Congestion-Based Congestion Control".
BBR has significantly increased throughput and reduced latency for
connections on Google's internal backbone networks and google.com and
YouTube Web servers.
BBR requires only changes on the sender side, not in the network or
the receiver side. Thus it can be incrementally deployed on today's
Internet, or in datacenters.
The Internet has predominantly used loss-based congestion control
(largely Reno or CUBIC) since the 1980s, relying on packet loss as the
signal to slow down. While this worked well for many years, loss-based
congestion control is unfortunately out-dated in today's networks. On
today's Internet, loss-based congestion control causes the infamous
bufferbloat problem, often causing seconds of needless queuing delay,
since it fills the bloated buffers in many last-mile links. On today's
high-speed long-haul links using commodity switches with shallow
buffers, loss-based congestion control has abysmal throughput because
it over-reacts to losses caused by transient traffic bursts.
In 1981 Kleinrock and Gale showed that the optimal operating point for
a network maximizes delivered bandwidth while minimizing delay and
loss, not only for single connections but for the network as a
whole. Finding that optimal operating point has been elusive, since
any single network measurement is ambiguous: network measurements are
the result of both bandwidth and propagation delay, and those two
cannot be measured simultaneously.
While it is impossible to disambiguate any single bandwidth or RTT
measurement, a connection's behavior over time tells a clearer
story. BBR uses a measurement strategy designed to resolve this
ambiguity. It combines these measurements with a robust servo loop
using recent control systems advances to implement a distributed
congestion control algorithm that reacts to actual congestion, not
packet loss or transient queue delay, and is designed to converge with
high probability to a point near the optimal operating point.
In a nutshell, BBR creates an explicit model of the network pipe by
sequentially probing the bottleneck bandwidth and RTT. On the arrival
of each ACK, BBR derives the current delivery rate of the last round
trip, and feeds it through a windowed max-filter to estimate the
bottleneck bandwidth. Conversely it uses a windowed min-filter to
estimate the round trip propagation delay. The max-filtered bandwidth
and min-filtered RTT estimates form BBR's model of the network pipe.
Using its model, BBR sets control parameters to govern sending
behavior. The primary control is the pacing rate: BBR applies a gain
multiplier to transmit faster or slower than the observed bottleneck
bandwidth. The conventional congestion window (cwnd) is now the
secondary control; the cwnd is set to a small multiple of the
estimated BDP (bandwidth-delay product) in order to allow full
utilization and bandwidth probing while bounding the potential amount
of queue at the bottleneck.
When a BBR connection starts, it enters STARTUP mode and applies a
high gain to perform an exponential search to quickly probe the
bottleneck bandwidth (doubling its sending rate each round trip, like
slow start). However, instead of continuing until it fills up the
buffer (i.e. a loss), or until delay or ACK spacing reaches some
threshold (like Hystart), it uses its model of the pipe to estimate
when that pipe is full: it estimates the pipe is full when it notices
the estimated bandwidth has stopped growing. At that point it exits
STARTUP and enters DRAIN mode, where it reduces its pacing rate to
drain the queue it estimates it has created.
Then BBR enters steady state. In steady state, PROBE_BW mode cycles
between first pacing faster to probe for more bandwidth, then pacing
slower to drain any queue that created if no more bandwidth was
available, and then cruising at the estimated bandwidth to utilize the
pipe without creating excess queue. Occasionally, on an as-needed
basis, it sends significantly slower to probe for RTT (PROBE_RTT
mode).
BBR has been fully deployed on Google's wide-area backbone networks
and we're experimenting with BBR on Google.com and YouTube on a global
scale. Replacing CUBIC with BBR has resulted in significant
improvements in network latency and application (RPC, browser, and
video) metrics. For more details please refer to our upcoming ACM
Queue publication.
Example performance results, to illustrate the difference between BBR
and CUBIC:
Resilience to random loss (e.g. from shallow buffers):
Consider a netperf TCP_STREAM test lasting 30 secs on an emulated
path with a 10Gbps bottleneck, 100ms RTT, and 1% packet loss
rate. CUBIC gets 3.27 Mbps, and BBR gets 9150 Mbps (2798x higher).
Low latency with the bloated buffers common in today's last-mile links:
Consider a netperf TCP_STREAM test lasting 120 secs on an emulated
path with a 10Mbps bottleneck, 40ms RTT, and 1000-packet bottleneck
buffer. Both fully utilize the bottleneck bandwidth, but BBR
achieves this with a median RTT 25x lower (43 ms instead of 1.09
secs).
Our long-term goal is to improve the congestion control algorithms
used on the Internet. We are hopeful that BBR can help advance the
efforts toward this goal, and motivate the community to do further
research.
Test results, performance evaluations, feedback, and BBR-related
discussions are very welcome in the public e-mail list for BBR:
https://groups.google.com/forum/#!forum/bbr-dev
NOTE: BBR *must* be used with the fq qdisc ("man tc-fq") with pacing
enabled, since pacing is integral to the BBR design and
implementation. BBR without pacing would not function properly, and
may incur unnecessary high packet loss rates.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit introduces an optional new "omnipotent" hook,
cong_control(), for congestion control modules. The cong_control()
function is called at the end of processing an ACK (i.e., after
updating sequence numbers, the SACK scoreboard, and loss
detection). At that moment we have precise delivery rate information
the congestion control module can use to control the sending behavior
(using cwnd, TSO skb size, and pacing rate) in any CA state.
This function can also be used by a congestion control that prefers
not to use the default cwnd reduction approach (i.e., the PRR
algorithm) during CA_Recovery to control the cwnd and sending rate
during loss recovery.
We take advantage of the fact that recent changes defer the
retransmission or transmission of new data (e.g. by F-RTO) in recovery
until the new tcp_cong_control() function is run.
With this commit, we only run tcp_update_pacing_rate() if the
congestion control is not using this new API. New congestion controls
which use the new API do not want the TCP stack to run the default
pacing rate calculation and overwrite whatever pacing rate they have
chosen at initialization time.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the TCP send buffer expands to twice cwnd, in order to allow
limited transmits in the CA_Recovery state. This assumes that cwnd
does not increase in the CA_Recovery.
For some congestion control algorithms, like the upcoming BBR module,
if the losses in recovery do not indicate congestion then we may
continue to raise cwnd multiplicatively in recovery. In such cases the
current multiplier will falsely limit the sending rate, much as if it
were limited by the application.
This commit adds an optional congestion control callback to use a
different multiplier to expand the TCP send buffer. For congestion
control modules that do not specificy this callback, TCP continues to
use the previous default of 2.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export tcp_mss_to_mtu(), so that congestion control modules can use
this to help calculate a pacing rate.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow congestion control modules to use the default TSO auto-sizing
algorithm as one of the ingredients in their own decision about TSO sizing:
1) Export tcp_tso_autosize() so that CC modules can use it.
2) Change tcp_tso_autosize() to allow callers to specify a minimum
number of segments per TSO skb, in case the congestion control
module has a different notion of the best floor for TSO skbs for
the connection right now. For very low-rate paths or policed
connections it can be appropriate to use smaller TSO skbs.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the tso_segs_goal() function in tcp_congestion_ops to allow the
congestion control module to specify the number of segments that
should be in a TSO skb sent by tcp_write_xmit() and
tcp_xmit_retransmit_queue(). The congestion control module can either
request a particular number of segments in TSO skb that we transmit,
or return 0 if it doesn't care.
This allows the upcoming BBR congestion control module to select small
TSO skb sizes if the module detects that the bottleneck bandwidth is
very low, or that the connection is policed to a low rate.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit export two new fields in struct tcp_info:
tcpi_delivery_rate: The most recent goodput, as measured by
tcp_rate_gen(). If the socket is limited by the sending
application (e.g., no data to send), it reports the highest
measurement instead of the most recent. The unit is bytes per
second (like other rate fields in tcp_info).
tcpi_delivery_rate_app_limited: A boolean indicating if the goodput
was measured when the socket's throughput was limited by the
sending application.
This delivery rate information can be useful for applications that
want to know the current throughput the TCP connection is seeing,
e.g. adaptive bitrate video streaming. It can also be very useful for
debugging or troubleshooting.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds code to track whether the delivery rate represented
by each rate_sample was limited by the application.
Upon each transmit, we store in the is_app_limited field in the skb a
boolean bit indicating whether there is a known "bubble in the pipe":
a point in the rate sample interval where the sender was
application-limited, and did not transmit even though the cwnd and
pacing rate allowed it.
This logic marks the flow app-limited on a write if *all* of the
following are true:
1) There is less than 1 MSS of unsent data in the write queue
available to transmit.
2) There is no packet in the sender's queues (e.g. in fq or the NIC
tx queue).
3) The connection is not limited by cwnd.
4) There are no lost packets to retransmit.
The tcp_rate_check_app_limited() code in tcp_rate.c determines whether
the connection is application-limited at the moment. If the flow is
application-limited, it sets the tp->app_limited field. If the flow is
application-limited then that means there is effectively a "bubble" of
silence in the pipe now, and this silence will be reflected in a lower
bandwidth sample for any rate samples from now until we get an ACK
indicating this bubble has exited the pipe: specifically, until we get
an ACK for the next packet we transmit.
When we send every skb we record in scb->tx.is_app_limited whether the
resulting rate sample will be application-limited.
The code in tcp_rate_gen() checks to see when it is safe to mark all
known application-limited bubbles of silence as having exited the
pipe. It does this by checking to see when the delivered count moves
past the tp->app_limited marker. At this point it zeroes the
tp->app_limited marker, as all known bubbles are out of the pipe.
We make room for the tx.is_app_limited bit in the skb by borrowing a
bit from the in_flight field used by NV to record the number of bytes
in flight. The receive window in the TCP header is 16 bits, and the
max receive window scaling shift factor is 14 (RFC 1323). So the max
receive window offered by the TCP protocol is 2^(16+14) = 2^30. So we
only need 30 bits for the tx.in_flight used by NV.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generates data delivery rate (throughput) samples on a
per-ACK basis. These rate samples can be used by congestion control
modules, and specifically will be used by TCP BBR in later patches in
this series.
Key state:
tp->delivered: Tracks the total number of data packets (original or not)
delivered so far. This is an already-existing field.
tp->delivered_mstamp: the last time tp->delivered was updated.
Algorithm:
A rate sample is calculated as (d1 - d0)/(t1 - t0) on a per-ACK basis:
d1: the current tp->delivered after processing the ACK
t1: the current time after processing the ACK
d0: the prior tp->delivered when the acked skb was transmitted
t0: the prior tp->delivered_mstamp when the acked skb was transmitted
When an skb is transmitted, we snapshot d0 and t0 in its control
block in tcp_rate_skb_sent().
When an ACK arrives, it may SACK and ACK some skbs. For each SACKed
or ACKed skb, tcp_rate_skb_delivered() updates the rate_sample struct
to reflect the latest (d0, t0).
Finally, tcp_rate_gen() generates a rate sample by storing
(d1 - d0) in rs->delivered and (t1 - t0) in rs->interval_us.
One caveat: if an skb was sent with no packets in flight, then
tp->delivered_mstamp may be either invalid (if the connection is
starting) or outdated (if the connection was idle). In that case,
we'll re-stamp tp->delivered_mstamp.
At first glance it seems t0 should always be the time when an skb was
transmitted, but actually this could over-estimate the rate due to
phase mismatch between transmit and ACK events. To track the delivery
rate, we ensure that if packets are in flight then t0 and and t1 are
times at which packets were marked delivered.
If the initial and final RTTs are different then one may be corrupted
by some sort of noise. The noise we see most often is sending gaps
caused by delayed, compressed, or stretched acks. This either affects
both RTTs equally or artificially reduces the final RTT. We approach
this by recording the info we need to compute the initial RTT
(duration of the "send phase" of the window) when we recorded the
associated inflight. Then, for a filter to avoid bandwidth
overestimates, we generalize the per-sample bandwidth computation
from:
bw = delivered / ack_phase_rtt
to the following:
bw = delivered / max(send_phase_rtt, ack_phase_rtt)
In large-scale experiments, this filtering approach incorporating
send_phase_rtt is effective at avoiding bandwidth overestimates due to
ACK compression or stretched ACKs.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the number of packets that a TCP connection marks lost.
Congestion control modules can use this loss rate information for more
intelligent decisions about how fast to send.
Specifically, this is used in TCP BBR policer detection. BBR uses a
high packet loss rate as one signal in its policer detection and
policer bandwidth estimation algorithm.
The BBR policer detection algorithm cannot simply track retransmits,
because a retransmit can be (and often is) an indicator of packets
lost long, long ago. This is particularly true in a long CA_Loss
period that repairs the initial massive losses when a policer kicks
in.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert to the tcp_skb_cb size check that tcp_init() had before commit
b4772ef879 ("net: use common macro for assering skb->cb[] available
size in protocol families"). As related commit 744d5a3e9f ("net:
move skb->dropcount to skb->cb[]") explains, the
sock_skb_cb_check_size() mechanism was added to ensure that there is
space for dropcount, "for protocol families using it". But TCP is not
a protocol using dropcount, so tcp_init() doesn't need to provision
space for dropcount in the skb->cb[], and thus we can revert to the
older form of the tcp_skb_cb size check. Doing so allows TCP to use 4
more bytes of the skb->cb[] space.
Fixes: b4772ef879 ("net: use common macro for assering skb->cb[] available size in protocol families")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds to the fq module a low_rate_threshold parameter to
insert a delay after all packets if the socket requests a pacing rate
below the threshold.
This helps achieve more precise control of the sending rate with
low-rate paths, especially policers. The basic issue is that if a
congestion control module detects a policer at a certain rate, it may
want fq to be able to shape to that policed rate. That way the sender
can avoid policer drops by having the packets arrive at the policer at
or just under the policed rate.
The default threshold of 550Kbps was chosen analytically so that for
policers or links at 500Kbps or 512Kbps fq would very likely invoke
this mechanism, even if the pacing rate was briefly slightly above the
available bandwidth. This value was then empirically validated with
two years of production testing on YouTube video servers.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the TCP min_rtt code to reuse the new win_minmax library in
lib/win_minmax.c to simplify the TCP code.
This is a pure refactor: the functionality is exactly the same. We
just moved the windowed min code to make TCP easier to read and
maintain, and to allow other parts of the kernel to use the windowed
min/max filter code.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upcoming change "lib/win_minmax: windowed min or max estimator"
introduces a struct called minmax, which is then included in
include/linux/tcp.h in the upcoming change "tcp: use windowed min
filter library for TCP min_rtt estimation". This would create a
compilation error for tcp_cdg.c, which defines its own minmax
struct. To avoid this naming conflict (and potentially others in the
future), this commit renames the version used in tcp_cdg.c to
cdg_minmax.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the batch changes that translated transient actions into
a temporary list lost in the translation was the fact that
tcf_action_destroy() will eventually delete the action from
the permanent location if the refcount is zero.
Example of what broke:
...add a gact action to drop
sudo $TC actions add action drop index 10
...now retrieve it, looks good
sudo $TC actions get action gact index 10
...retrieve it again and find it is gone!
sudo $TC actions get action gact index 10
Fixes: 22dc13c837 ("net_sched: convert tcf_exts from list to pointer array"),
Fixes: 824a7e8863 ("net_sched: remove an unnecessary list_del()")
Fixes: f07fed82ad ("net_sched: remove the leftover cleanup_a()")
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work implements direct packet access for helpers and direct packet
write in a similar fashion as already available for XDP types via commits
4acf6c0b84 ("bpf: enable direct packet data write for xdp progs") and
6841de8b0d ("bpf: allow helpers access the packet directly"), and as a
complementary feature to the already available direct packet read for tc
(cls/act) programs.
For enabling this, we need to introduce two helpers, bpf_skb_pull_data()
and bpf_csum_update(). The first is generally needed for both, read and
write, because they would otherwise only be limited to the current linear
skb head. Usually, when the data_end test fails, programs just bail out,
or, in the direct read case, use bpf_skb_load_bytes() as an alternative
to overcome this limitation. If such data sits in non-linear parts, we
can just pull them in once with the new helper, retest and eventually
access them.
At the same time, this also makes sure the skb is uncloned, which is, of
course, a necessary condition for direct write. As this needs to be an
invariant for the write part only, the verifier detects writes and adds
a prologue that is calling bpf_skb_pull_data() to effectively unclone the
skb from the very beginning in case it is indeed cloned. The heuristic
makes use of a similar trick that was done in 233577a220 ("net: filter:
constify detection of pkt_type_offset"). This comes at zero cost for other
programs that do not use the direct write feature. Should a program use
this feature only sparsely and has read access for the most parts with,
for example, drop return codes, then such write action can be delegated
to a tail called program for mitigating this cost of potential uncloning
to a late point in time where it would have been paid similarly with the
bpf_skb_store_bytes() as well. Advantage of direct write is that the
writes are inlined whereas the helper cannot make any length assumptions
and thus needs to generate a call to memcpy() also for small sizes, as well
as cost of helper call itself with sanity checks are avoided. Plus, when
direct read is already used, we don't need to cache or perform rechecks
on the data boundaries (due to verifier invalidating previous checks for
helpers that change skb->data), so more complex programs using rewrites
can benefit from switching to direct read plus write.
For direct packet access to helpers, we save the otherwise needed copy into
a temp struct sitting on stack memory when use-case allows. Both facilities
are enabled via may_access_direct_pkt_data() in verifier. For now, we limit
this to map helpers and csum_diff, and can successively enable other helpers
where we find it makes sense. Helpers that definitely cannot be allowed for
this are those part of bpf_helper_changes_skb_data() since they can change
underlying data, and those that write into memory as this could happen for
packet typed args when still cloned. bpf_csum_update() helper accommodates
for the fact that we need to fixup checksum_complete when using direct write
instead of bpf_skb_store_bytes(), meaning the programs can use available
helpers like bpf_csum_diff(), and implement csum_add(), csum_sub(),
csum_block_add(), csum_block_sub() equivalents in eBPF together with the
new helper. A usage example will be provided for iproute2's examples/bpf/
directory.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit commit db74a3335e ("openvswitch: use percpu
flow stats") flow alloc resets flow-key. So there is no need
to reset the flow-key again if OVS is using newly allocated
flow-key.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to declare separate key on stack,
we can just use sw_flow->key to store the key directly.
This commit fixes following warning:
net/openvswitch/datapath.c: In function ‘ovs_flow_cmd_new’:
net/openvswitch/datapath.c:1080:1: warning: the frame size of 1040 bytes
is larger than 1024 bytes [-Wframe-larger-than=]
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-09-19
Here's the main bluetooth-next pull request for the 4.9 kernel.
- Added new messages for monitor sockets for better mgmt tracing
- Added local name and appearance support in scan response
- Added new Qualcomm WCNSS SMD based HCI driver
- Minor fixes & cleanup to 802.15.4 code
- New USB ID to btusb driver
- Added Marvell support to HCI UART driver
- Add combined LED trigger for controller power
- Other minor fixes here and there
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only 1 of the 3 drivers currently has a set_addr() operation. Make the
set_addr() callback optional to reduce the amount of empty stubs inside
the drivers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 83c0afaec7 ("net: dsa: Add new binding implementation")
has a duplicate invocation of the set_addr() operation callback. Remove one
of them.
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 currently uses rhashtable with insecure_elasticity set
to true. The latter is because of duplicate objects. What's
more, mac80211 walks the rhashtable chains by hand which is broken
as rhashtable may contain multiple tables due to resizing or
rehashing.
This patch fixes it by converting it to the newly added rhltable
interface which is designed for use with duplicate objects.
With rhltable a lookup returns a list of objects instead of a
single one. This is then fed into the existing for_each_sta_info
macro.
This patch also deletes the sta_addr_hash function since rhashtable
defaults to jhash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8c14586fc3 ("net: ipv6: Use passed in table for nexthop
lookups") introduced a regression: insertion of an IPv6 route in a table
not containing the appropriate connected route for the gateway but which
contained a non-connected route (like a default gateway) fails while it
was previously working:
$ ip link add eth0 type dummy
$ ip link set up dev eth0
$ ip addr add 2001:db8::1/64 dev eth0
$ ip route add ::/0 via 2001:db8::5 dev eth0 table 20
$ ip route add 2001:db8:cafe::1/128 via 2001:db8::6 dev eth0 table 20
RTNETLINK answers: No route to host
$ ip -6 route show table 20
default via 2001:db8::5 dev eth0 metric 1024 pref medium
After this patch, we get:
$ ip route add 2001:db8:cafe::1/128 via 2001:db8::6 dev eth0 table 20
$ ip -6 route show table 20
2001:db8:cafe::1 via 2001:db8::6 dev eth0 metric 1024 pref medium
default via 2001:db8::5 dev eth0 metric 1024 pref medium
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
setting conforming action to drop is a valid policy.
When it is set we need to at least see the stats indicating it
for debugging.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sample use case of how this is encoded:
user space via tuntap (or a connected VM/Machine/container)
encodes the tcindex TLV.
Sample use case of decoding:
IFE action decodes it and the skb->tc_index is then used to classify.
So something like this for encoded ICMP packets:
.. first decode then reclassify... skb->tcindex will be set
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xbeef \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify
...next match the decode icmp packet...
sudo $TC filter add dev $ETH parent ffff: prio 4 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue
... last classify it using the tcindex classifier and do someaction..
sudo $TC filter add dev $ETH parent ffff: prio 5 protocol ip \
handle 0x11 tcindex classid 1:1 \
action blah..
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 8a29111c7 ("net: gro: allow to build full sized skb")
gro may build buffers with a frag_list. This can hurt forwarding
because most NICs can't offload such packets, they need to be
segmented in software. This patch splits buffers with a frag_list
at the frag_list pointer into buffers that can be TSO offloaded.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a socket is cloned, the associated sock_cgroup_data is duplicated
but not its reference on the cgroup. As a result, the cgroup reference
count will underflow when both sockets are destroyed later on.
Fixes: bd1060a1d6 ("sock, cgroup: add sock->sk_cgroup")
Link: http://lkml.kernel.org/r/20160914194846.11153-2-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting appearance on controllers without LE support will result
in No Supported error.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds missing event when setting appearance, just like
in the set local name command.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds EIR data to extended info changed event.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If LE is enabled appearance is added to EIR data.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This will also be used for Extended Information Event handling.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is no need to allocate heap for reply only to copy stack data to
it. This also fix rp memory leak and missing hdev unlock if kmalloc
failed.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to the recently added
Read Extended Controller Information and Set Appearance commands.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables prepending appearance value to scan response data.
It also adds support for setting appearance value through mgmt command.
If currently advertised instance has apperance flag set it is expired
immediately.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables appending local name to scan response data. If
currently advertised instance has name flag set it is expired
immediately.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use kzalloc rather than kmalloc followed by memset with 0.
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A comment in the code states that SCO connection should be rejected
with the proper error value between 0xd-0xf. The code uses
HCI_ERROR_REMOTE_LOW_RESOURCES which is 0x14.
This led to following error:
< HCI Command: Reject Synchronous Co.. (0x01|0x002a) plen 7
Address: 34:51:C9:EF:02:CA (Apple, Inc.)
Reason: Remote Device Terminated due to Low Resources (0x14)
> HCI Event: Command Status (0x0f) plen 4
Reject Synchronous Connection Request (0x01|0x002a) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Instead make use of HCI_ERROR_REJ_LIMITED_RESOURCES which is 0xd.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When closing HCI User Channel, the New Settings event was send out to
inform about changed settings. However such event is wrong since the
exclusive HCI User Channel access is active until the Index Added event
has been sent.
@ USER Close: test
@ MGMT Event: New Settings (0x0006) plen 4
Current settings: 0x00000ad0
Bondable
Secure Simple Pairing
BR/EDR
Low Energy
Secure Connections
= Close Index: 00:14:EF:22:04:12
@ MGMT Event: Index Added (0x0004) plen 0
Calling __mgmt_power_off from hci_dev_do_close requires an extra check
for an active HCI User Channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When opening and closing HCI user channel, send monitoring messages to
be able to trace its behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds device class, complete local name and short local name
to EIR data in Extended Controller Info as specified in docs.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This command is used to retrieve the current state and basic
information of a controller. It is typically used right after
getting the response to the Read Controller Index List command
or an Index Added event (or its extended counterparts).
When any of the values in the EIR_Data field changes, the event
Extended Controller Information Changed will be used to inform
clients about the updated information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
In case an unbound HCI raw socket is later on bound, ensure that the
monitor notification messages indicate a close and re-open. None of
the userspace tools use the socket this, but it is actually possible
to use an ioctl on an unbound socket and then later bind it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When opening and closing HCI raw sockets their main usage is for legacy
userspace. To track interaction with the modern mgmt interface, send
open and close monitoring messages for these action.
The HCI raw sockets is special since it supports unbound ioctl operation
and for that special case delay the notification message until at least
one ioctl has been executed. The difference between a bound and unbound
socket will be detailed by the fact the HCI index is present or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The control open and close monitoring events require special channel
checks to ensure messages are only send when the right events happen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Assignment of the hci_pi(sk)->channel should be done early when binding
the HCI socket. This avoids confusion with the RAW channel that is used
for legacy access.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Only when the cookie has been assigned, then send the open and close
monitor messages. Also if the socket is bound to a device, then include
the index into the message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of keeping a version string around, use version and revision
numbers and then stringify them for use as module parameter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of manually allocating cookie information each time, use helper
functions for generating and releasing cookies.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case of failure, the Set IO Capability command is suppose to return
command status and not command complete.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The address information of the Get Clock Information return parameters
is copying from a different memory location. It uses &cmd->param while
it actually needs to be cmd->param.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of hiding everything behind a general managment events flag,
introduce indivdual flags that allow fine control over which events are
send to a given management channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When an Advertising Instance is removed, the Advertising Removed event
shouldn't be sent to the same socket that issued the Remove
Advertising command (it gets a command complete event instead). The
mgmt_advertising_removed() function already has a parameter for
skipping a specific socket, but there was no code to propagate the
right value to this parameter. This patch fixes the issue by making
sure the intermediate hci_req_clear_adv_instance() function gets the
socket pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for tracing all management commands and events via the
monitor interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This sends new notifications to the monitor support whenever a
management channel has been opened or closed. This allows tracing of
control channels really easily.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The mgmt version information will be also needed for the control
changell tracing feature. This provides a helper to pack them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To further allow unique identification and tracking of control socket,
store cookie and comm information when binding the socket.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SOL_HCI level should be enforced when using socket options on the
HCI raw socket interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Just because we don't support certain types of frames yet doesn't mean
we have to flood the message log with warnings about "invalid" frames.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes handling to remove short address for a neigbour entry
if RS/RA/NS/NA doesn't contain a short address. If these messages
doesn't has any short address option, the existing short address from
ndisc cache will be used. The current behaviour will set that the
neigbour doesn't has a short address anymore.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets the net namespace when creating SoftMAC interfaces. This
is important if the namespace at phy layer was switched before.
Currently we losing interfaces in some namespace and it's not possible
to recover that.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of just having a LED trigger for power on a specific controller,
this adds the LED trigger "bluetooth-power" that combines the power
states of all controllers into a single trigger. This simplifies the
trigger selection and also supports multiple controllers per host
system via a single LED.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Write space becoming available may race with putting the task to sleep
in xprt_wait_for_buffer_space(). The existing mechanism to avoid the
race does not work.
This (edited) partial trace illustrates the problem:
[1] rpc_task_run_action: task:43546@5 ... action=call_transmit
[2] xs_write_space <-xs_tcp_write_space
[3] xprt_write_space <-xs_write_space
[4] rpc_task_sleep: task:43546@5 ...
[5] xs_write_space <-xs_tcp_write_space
[1] Task 43546 runs but is out of write space.
[2] Space becomes available, xs_write_space() clears the
SOCKWQ_ASYNC_NOSPACE bit.
[3] xprt_write_space() attemts to wake xprt->snd_task (== 43546), but
this has not yet been queued and the wake up is lost.
[4] xs_nospace() is called which calls xprt_wait_for_buffer_space()
which queues task 43546.
[5] The call to sk->sk_write_space() at the end of xs_nospace() (which
is supposed to handle the above race) does not call
xprt_write_space() as the SOCKWQ_ASYNC_NOSPACE bit is clear and
thus the task is not woken.
Fix the race by resetting the SOCKWQ_ASYNC_NOSPACE bit in xs_nospace()
so the second call to sk->sk_write_space() calls xprt_write_space().
Suggested-by: Trond Myklebust <trondmy@primarydata.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
cc: stable@vger.kernel.org # 4.4
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: the extra layer of indirection doesn't add value.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: When converting xprtrdma to use the new CQ API, I missed a
spot. The naming convention elsewhere is:
{svc_rdma,rpcrdma}_wc_{operation}
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Tie frwr debugging messages together by always reporting the address
of the frwr.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The Version One default inline threshold is still 1KB. But allow
testing with thresholds up to 64KB.
This maximum is somewhat arbitrary. There's no fundamental
architectural limit I'm aware of, but it's good to keep the size of
Receive buffers reasonable. Now that Send can use a s/g list, a
Send buffer is only as large as each RPC requires. Receive buffers
are always the size of the inline threshold, however.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
An RPC Call message that is sent inline but that has a data payload
(ie, one or more items in rq_snd_buf's page list) must be "pulled
up:"
- call_allocate has to reserve enough RPC Call buffer space to
accommodate the data payload
- call_transmit has to memcopy the rq_snd_buf's page list and tail
into its head iovec before it is sent
As the inline threshold is increased beyond its current 1KB default,
however, this means data payloads of more than a few KB are copied
by the host CPU. For example, if the inline threshold is increased
just to 4KB, then NFS WRITE requests up to 4KB would involve a
memcpy of the NFS WRITE's payload data into the RPC Call buffer.
This is an undesirable amount of participation by the host CPU.
The inline threshold may be much larger than 4KB in the future,
after negotiation with a peer server.
Instead of copying the components of rq_snd_buf into its head iovec,
construct a gather list of these components, and send them all in
place. The same approach is already used in the Linux server's
RPC-over-RDMA reply path.
This mechanism also eliminates the need for rpcrdma_tail_pullup,
which is used to manage the XDR pad and trailing inline content when
a Read list is present.
This requires that the pages in rq_snd_buf's page list be DMA-mapped
during marshaling, and unmapped when a data-bearing RPC is
completed. This is slightly less efficient for very small I/O
payloads, but significantly more efficient as data payload size and
inline threshold increase past a kilobyte.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Have frwr's ro_unmap_sync recognize an invalidated rkey that appears
as part of a Receive completion. Local invalidation can be skipped
for that rkey.
Use an out-of-band signaling mechanism to indicate to the server
that the client is prepared to receive RDMA Send With Invalidate.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Send an RDMA-CM private message on connect, and look for one during
a connection-established event.
Both sides can communicate their various implementation limits.
Implementations that don't support this sideband protocol ignore it.
Once the client knows the server's inline threshold maxima, it can
adjust the use of Reply chunks, and eliminate most use of Position
Zero Read chunks. Moderately-sized I/O can be done using a pure
inline RDMA Send instead of RDMA operations that require memory
registration.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: The fields in the recv_wr do not vary. There is no need to
initialize them before each ib_post_recv(). This removes a large-ish
data structure from the stack.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Most of the fields in each send_wr do not vary. There is
no need to initialize them before each ib_post_send(). This removes
a large-ish data structure from the stack.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up.
Since commit fc66448549 ("xprtrdma: Split the completion queue"),
rpcrdma_ep_post_recv() no longer uses the "ep" argument.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up. The "ia" argument is no longer used.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Currently, each regbuf is allocated and DMA mapped at the same time.
This is done during transport creation.
When a device driver is unloaded, every DMA-mapped buffer in use by
a transport has to be unmapped, and then remapped to the new
device if the driver is loaded again. Remapping will have to be done
_after_ the connect worker has set up the new device.
But there's an ordering problem:
call_allocate, which invokes xprt_rdma_allocate which calls
rpcrdma_alloc_regbuf to allocate Send buffers, happens _before_
the connect worker can run to set up the new device.
Instead, at transport creation, allocate each buffer, but leave it
unmapped. Once the RPC carries these buffers into ->send_request, by
which time a transport connection should have been established,
check to see that the RPC's buffers have been DMA mapped. If not,
map them there.
When device driver unplug support is added, it will simply unmap all
the transport's regbufs, but it doesn't have to deallocate the
underlying memory.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The use of DMA_BIDIRECTIONAL is discouraged by DMA-API.txt.
Fortunately, xprtrdma now knows which direction I/O is going as
soon as it allocates each regbuf.
The RPC Call and Reply buffers are no longer the same regbuf. They
can each be labeled correctly now. The RPC Reply buffer is never
part of either a Send or Receive WR, but it can be part of Reply
chunk, which is mapped and registered via ->ro_map . So it is not
DMA mapped when it is allocated (DMA_NONE), to avoid a double-
mapping.
Since Receive buffers are no longer DMA_BIDIRECTIONAL and their
contents are never modified by the host CPU, DMA-API-HOWTO.txt
suggests that a DMA sync before posting each buffer should be
unnecessary. (See my_card_interrupt_handler).
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Commit 949317464b ("xprtrdma: Limit number of RDMA segments in
RPC-over-RDMA headers") capped the number of chunks that may appear
in RPC-over-RDMA headers. The maximum header size can be estimated
and fixed to avoid allocating buffer space that is never used.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
RPC-over-RDMA needs to separate its RPC call and reply buffers.
o When an RPC Call is sent, rq_snd_buf is DMA mapped for an RDMA
Send operation using DMA_TO_DEVICE
o If the client expects a large RPC reply, it DMA maps rq_rcv_buf
as part of a Reply chunk using DMA_FROM_DEVICE
The two mappings are for data movement in opposite directions.
DMA-API.txt suggests that if these mappings share a DMA cacheline,
bad things can happen. This could occur in the final bytes of
rq_snd_buf and the first bytes of rq_rcv_buf if the two buffers
happen to share a DMA cacheline.
On x86_64 the cacheline size is typically 8 bytes, and RPC call
messages are usually much smaller than the send buffer, so this
hasn't been a noticeable problem. But the DMA cacheline size can be
larger on other platforms.
Also, often rq_rcv_buf starts most of the way into a page, thus
an additional RDMA segment is needed to map and register the end of
that buffer. Try to avoid that scenario to reduce the cost of
registering and invalidating Reply chunks.
Instead of carrying a single regbuf that covers both rq_snd_buf and
rq_rcv_buf, each struct rpcrdma_req now carries one regbuf for
rq_snd_buf and one regbuf for rq_rcv_buf.
Some incidental changes worth noting:
- To clear out some spaghetti, refactor xprt_rdma_allocate.
- The value stored in rg_size is the same as the value stored in
the iov.length field, so eliminate rg_size
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Currently there's a hidden and indirect mechanism for finding the
rpcrdma_req that goes with an rpc_rqst. It depends on getting from
the rq_buffer pointer in struct rpc_rqst to the struct
rpcrdma_regbuf that controls that buffer, and then to the struct
rpcrdma_req it goes with.
This was done back in the day to avoid the need to add a per-rqst
pointer or to alter the buf_free API when support for RPC-over-RDMA
was introduced.
I'm about to change the way regbuf's work to support larger inline
thresholds. Now is a good time to replace this indirect mechanism
with something that is more straightforward. I guess this should be
considered a clean up.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
For xprtrdma, the RPC Call and Reply buffers are involved in real
I/O operations.
To start with, the DMA direction of the I/O for a Call is opposite
that of a Reply.
In the current arrangement, the Reply buffer address is on a
four-byte alignment just past the call buffer. Would be friendlier
on some platforms if that was at a DMA cache alignment instead.
Because the current arrangement allocates a single memory region
which contains both buffers, the RPC Reply buffer often contains a
page boundary in it when the Call buffer is large enough (which is
frequent).
It would be a little nicer for setting up DMA operations (and
possible registration of the Reply buffer) if the two buffers were
separated, well-aligned, and contained as few page boundaries as
possible.
Now, I could just pad out the single memory region used for the pair
of buffers. But frequently that would mean a lot of unused space to
ensure the Reply buffer did not have a page boundary.
Add a separate pointer to rpc_rqst that points right to the RPC
Reply buffer. This makes no difference to xprtsock, but it will help
xprtrdma in subsequent patches.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
xprtrdma needs to allocate the Call and Reply buffers separately.
TBH, the reliance on using a single buffer for the pair of XDR
buffers is transport implementation-specific.
Instead of passing just the rq_buffer into the buf_free method, pass
the task structure and let buf_free take care of freeing both
XDR buffers at once.
There's a micro-optimization here. In the common case, both
xprt_release and the transport's buf_free method were checking if
rq_buffer was NULL. Now the check is done only once per RPC.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
xprtrdma needs to allocate the Call and Reply buffers separately.
TBH, the reliance on using a single buffer for the pair of XDR
buffers is transport implementation-specific.
Transports that want to allocate separate Call and Reply buffers
will ignore the "size" argument anyway. Don't bother passing it.
The buf_alloc method can't return two pointers. Instead, make the
method's return value an error code, and set the rq_buffer pointer
in the method itself.
This gives call_allocate an opportunity to terminate an RPC instead
of looping forever when a permanent problem occurs. If a request is
just bogus, or the transport is in a state where it can't allocate
resources for any request, there needs to be a way to kill the RPC
right there and not loop.
This immediately fixes a rare problem in the backchannel send path,
which loops if the server happens to send a CB request whose
call+reply size is larger than a page (which it shouldn't do yet).
One more issue: looks like xprt_inject_disconnect was incorrectly
placed in the failure path in call_allocate. It needs to be in the
success path, as it is for other call-sites.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: there is some XDR initialization logic that is common
to the forward channel and backchannel. Move it to an XDR header
so it can be shared.
rpc_rqst::rq_buffer points to a buffer containing big-endian data.
Update its annotation as part of the clean up.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: r_xprt is already available everywhere these macros are
invoked, so just dereference that directly.
RPCRDMA_INLINE_PAD_VALUE is no longer used, so it can simply be
removed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Use a setup function to call into the NFS layer to test an rpc_xprt
for session trunking so as to not leak the rpc_xprt_switch into
the nfs layer.
Search for the address in the rpc_xprt_switch first so as not to
put an unnecessary EXCHANGE_ID on the wire.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Give the NFS layer access to the rpc_xprt_switch_add_xprt function
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Give the NFS layer access to the xprt_switch_put function
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
rpc_task_set_client is only called from rpc_run_task after
rpc_new_task and rpc_task_release_client is not needed as the
task is new.
When called from rpc_new_task, rpc_task_set_client also removed the
assigned rpc_xprt which is not desired.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The variable `err` is not used anywhere and just returns the
predefined value `0` at the end of the function. Hence, remove the
variable and return 0 explicitly.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
commit 1a6509d991 ("[IPSEC]: Add support for combined mode algorithms")
introduced aead. The function attach_aead kmemdup()s the algorithm
name during xfrm_state_construct().
However this memory is never freed.
Implementation has since been slightly modified in
commit ee5c23176f ("xfrm: Clone states properly on migration")
without resolving this leak.
This patch adds a kfree() call for the aead algorithm name.
Fixes: 1a6509d991 ("[IPSEC]: Add support for combined mode algorithms")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Acked-by: Rami Rosen <roszenrami@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
-----BEGIN PGP SIGNATURE-----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=/2cJ
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160917-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Tracepoint addition and improvement
Here is a set of patches that add some more tracepoints and improve a couple
of existing ones. New additions include:
(1) Connection refcount tracking.
(2) Client connection state machine tracking.
(3) Tx and Rx packet lifecycle.
(4) ACK reception and transmission.
(5) recvmsg processing.
Updates include:
(1) Print the symbolic packet name in the Rx packet tracepoint.
(2) Additional call refcount trace events.
(3) Improvements to sk_buff tracking with AF_RXRPC.
In addition:
(1) Config option to inject packet loss during both transmission and
reception.
(2) Removal of some printks.
This series needs to be applied on top of the previously posted fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=MjVT
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160917-1' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fixes & miscellany
Here are some more AF_RXRPC fix patches with a couple of miscellaneous
changes also. Fixes include:
(1) Make RxRPC IPv6 support conditional on IPv6 being available.
(2) Move the condition check in rxrpc_locate_data() into the caller and
check the error return.
(3) Fix the detection of the last received packet in recvmsg.
(4) Account calls that need acceptance and clean up any unaccepted ones if
the socket gets closed.
(5) Fix the cleanup of client connections.
(6) Fix the soft-ACK parsing and the retransmission of packets based on
those ACKs.
(7) Suppress transmission of an ACK when there's no pending ACK to
transmit because another thread stole it.
And some miscellany:
(8) Whitespace removal.
(9) Switch-value consistency in rxrpc_send_call_packet().
(10) Fix the basic transmission packet size to allow for spur-of-the-moment
jumbo DATA packet production.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces sk_buff_head struct in Qdiscs with new qdisc_skb_head.
Its similar to the skb_buff_head api, but does not use skb->prev pointers.
Qdiscs will commonly enqueue at the tail of a list and dequeue at head.
While skb_buff_head works fine for this, enqueue/dequeue needs to also
adjust the prev pointer of next element.
The ->prev pointer is not required for qdiscs so we can just leave
it undefined and avoid one cacheline write access for en/dequeue.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After previous patch these functions are identical.
Replace __skb_dequeue in qdiscs with __qdisc_dequeue_head.
Next patch will then make __qdisc_dequeue_head handle
single-linked list instead of strcut sk_buff_head argument.
Doesn't change generated code.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves qdisc stat accouting to qdisc_dequeue_head.
The only direct caller of the __qdisc_dequeue_head version open-codes
this now.
This allows us to later use __qdisc_dequeue_head as a replacement
of __skb_dequeue() (which operates on sk_buff_head list).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A followup change will replace the sk_buff_head in the qdisc
struct with a slightly different list.
Use of the sk_buff_head helpers will thus cause compiler
warnings.
Open-code these accesses in an extra change to ease review.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 311b21774f ("sctp: simplify sk_receive_queue locking"), a call
to 'skb_queue_splice_tail_init()' has been made explicit. Previously it was
hidden in 'sctp_skb_list_tail()'
Now, the code around it looks redundant. The '_init()' part of
'skb_queue_splice_tail_init()' should already do the same.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add _nf_register_hooks() and _nf_unregister_hooks() calls which allow
caller to hold RTNL mutex.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make ip6_route_input_lookup available outside of ipv6 the module
similar to ip_route_input_noref in the IPv4 world.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a nested attribute of offload stats to if_stats_msg
named IFLA_STATS_LINK_OFFLOAD_XSTATS.
Under it, add SW stats, meaning stats only per packets that went via
slowpath to the cpu, named IFLA_OFFLOAD_XSTATS_CPU_HIT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
-----BEGIN PGP SIGNATURE-----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=s1MY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have various things - all across the board:
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* reject aggregation sessions for TSID/TID 8-16 that we
can never use anyway and which could confuse drivers
* check return value of skb_linearize()
-----BEGIN PGP SIGNATURE-----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=3dek
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Two more fixes:
* reject aggregation sessions for TSID/TID 8-16 that we
can never use anyway and which could confuse drivers
* check return value of skb_linearize()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When fq is used on 32bit kernels, we need to lock the qdisc before
copying 64bit fields.
Otherwise "tc -s qdisc ..." might report bogus values.
Fixes: afe4fd0624 ("pkt_sched: fq: Fair Queue packet scheduler")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using flow stats per NUMA node, use it per CPU. When using
megaflows, the stats lock can be a bottleneck in scalability.
On a E5-2690 12-core system, usual throughput went from ~4Mpps to
~15Mpps when forwarding between two 40GbE ports with a single flow
configured on the datapath.
This has been tested on a system with possible CPUs 0-7,16-23. After
module removal, there were no corruption on the slab cache.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Cc: pravin shelar <pshelar@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a system with only node 1 as possible, all statistics is going to be
accounted on node 0 as it will have a single writer.
However, when getting and clearing the statistics, node 0 is not going
to be considered, as it's not a possible node.
Tested that statistics are not zero on a system with only node 1
possible. Also compile-tested with CONFIG_NUMA off.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David and Marcelo's suggestion, ENOMEM err shouldn't return back to
user in transmit path. Instead, sctp's retransmit would take care of
the chunks that fail to send because of ENOMEM.
This patch is only to do some release job when alloc_skb fails, not to
return ENOMEM back any more.
Besides, it also cleans up sctp_packet_transmit's err path, and fixes
some issues in err path:
- It didn't free the head skb in nomem: path.
- No need to check nskb in no_route: path.
- It should goto err: path if alloc_skb fails for head.
- Not all the NOMEMs should free nskb.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_outq_flush return value is meaningless now, this patch is
to make sctp_outq_flush return void, as well as sctp_outq_fail
and sctp_outq_uncork.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time when sctp calls sctp_outq_flush, it sends out the chunks of
control queue, retransmit queue and data queue. Even if some trunks are
failed to transmit, it still has to flush all the transports, as it's
the only chance to clean that transmit_list.
So the latest transmit error here should be returned back. This transmit
error is an internal error of sctp stack.
I checked all the places where it uses the transmit error (the return
value of sctp_outq_flush), most of them are actually just save it to
sk_err.
Except for sctp_assoc/endpoint_bh_rcv, they will drop the chunk if
it's failed to send a REPLY, which is actually incorrect, as we can't
be sure the error that sctp_outq_flush returns is from sending that
REPLY.
So it's meaningless for sctp_outq_flush to return error back.
This patch is to save transmit error to sk_err in sctp_outq_flush, the
new error can update the old value. Eventually, sctp_wait_for_* would
check for it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last patch "sctp: do not return the transmit err back to sctp_sendmsg"
made sctp_primitive_SEND return err only when asoc state is unavailable.
In this case, chunks are not enqueued, they have no chance to be freed if
we don't take care of them later.
This Patch is actually to revert commit 1cd4d5c432 ("sctp: remove the
unused sctp_datamsg_free()"), commit 69b5777f2e ("sctp: hold the chunks
only after the chunk is enqueued in outq") and commit 8b570dc9f7 ("sctp:
only drop the reference on the datamsg after sending a msg"), to use
sctp_datamsg_free to free the chunks of current msg.
Fixes: 8b570dc9f7 ("sctp: only drop the reference on the datamsg after sending a msg")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once a chunk is enqueued successfully, sctp queues can take care of it.
Even if it is failed to transmit (like because of nomem), it should be
put into retransmit queue.
If sctp report this error to users, it confuses them, they may resend
that msg, but actually in kernel sctp stack is in charge of retransmit
it already.
Besides, this error probably is not from the failure of transmitting
current msg, but transmitting or retransmitting another msg's chunks,
as sctp_outq_flush just tries to send out all transports' chunks.
This patch is to make sctp_cmd_send_msg return avoid, and not return the
transmit err back to sctp_sendmsg
Fixes: 8b570dc9f7 ("sctp: only drop the reference on the datamsg after sending a msg")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Data Chunks are only sent by sctp_primitive_SEND, in which sctp checks
the asoc's state through statetable before calling sctp_outq_tail. So
there's no need to check the asoc's state again in sctp_outq_tail.
Besides, sctp_do_sm is protected by lock_sock, even if sending msg is
interrupted by timer events, the event's processes still need to acquire
lock_sock first. It means no others CMDs can be enqueue into side effect
list before CMD_SEND_MSG to change asoc->state, so it's safe to remove it.
This patch is to remove redundant asoc->state check from sctp_outq_tail.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to gre, vxlan, geneve tunnels allow IPIP6 and IP6IP6 tunnels
to operate in 'collect metadata' mode.
Unlike ipv4 code here it's possible to reuse ip6_tnl_xmit() function
for both collect_md and traditional tunnels.
bpf_skb_[gs]et_tunnel_key() helpers and ovs (in the future) are the users.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to gre, vxlan, geneve tunnels allow IPIP tunnels to
operate in 'collect metadata' mode.
bpf_skb_[gs]et_tunnel_key() helpers can make use of it right away.
ovs can use it as well in the future (once appropriate ovs-vport
abstractions and user apis are added).
Note that just like in other tunnels we cannot cache the dst,
since tunnel_info metadata can be different for every packet.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure. This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p = { ... };
@ok@
identifier r.i;
struct net_device e;
position p;
@@
e.netdev_ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct net_device_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct net_device_ops i = { ... };
// </smpl>
The result of size on this file before the change is:
text data bss dec hex filename
3401 931 44 4376 1118 net/l2tp/l2tp_eth.o
and after the change it is:
text data bss dec hex filename
3993 347 44 4384 1120 net/l2tp/l2tp_eth.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
With large BDP TCP flows and lossy networks, it is very important
to keep a low number of skbs in the write queue.
RACK and SACK processing can perform a linear scan of it.
We should avoid putting any payload in skb->head, so that SACK
shifting can be done if needed.
With this patch, we allow to pack ~0.5 MB per skb instead of
the 64KB initially cooked at tcp_sendmsg() time.
This gives a reduction of number of skbs in write queue by eight.
tcp_rack_detect_loss() likes this.
We still allow payload in skb->head for first skb put in the queue,
to not impact RPC workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb is not freed if newsk is NULL. Rework the error path so free_skb is
unconditionally called on function exit.
Fixes: c3ea9fa274 ("[IrDA] af_irda: IRDA_ASSERT cleanups")
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a TCP socket gets a large write queue, an overflow can happen
in a test in __tcp_retransmit_skb() preventing all retransmits.
The flow then stalls and resets after timeouts.
Tested:
sysctl -w net.core.wmem_max=1000000000
netperf -H dest -- -s 1000000000
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a configuration option to inject packet loss by discarding
approximately every 8th packet received and approximately every 8th DATA
packet transmitted.
Note that no locking is used, but it shouldn't really matter.
Signed-off-by: David Howells <dhowells@redhat.com>
Improve sk_buff tracing within AF_RXRPC by the following means:
(1) Use an enum to note the event type rather than plain integers and use
an array of event names rather than a big multi ?: list.
(2) Distinguish Rx from Tx packets and account them separately. This
requires the call phase to be tracked so that we know what we might
find in rxtx_buffer[].
(3) Add a parameter to rxrpc_{new,see,get,free}_skb() to indicate the
event type.
(4) A pair of 'rotate' events are added to indicate packets that are about
to be rotated out of the Rx and Tx windows.
(5) A pair of 'lost' events are added, along with rxrpc_lose_skb() for
packet loss injection recording.
Signed-off-by: David Howells <dhowells@redhat.com>
Remove _enter/_debug/_leave calls from rxrpc_recvmsg_data() of which one
uses an uninitialised variable.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a tracepoint to follow the insertion of a packet into the transmit
buffer, its transmission and its rotation out of the buffer.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a pair of tracepoints, one to track rxrpc_connection struct ref
counting and the other to track the client connection cache state.
Signed-off-by: David Howells <dhowells@redhat.com>
Add additional call tracepoint points for noting call-connected,
call-released and connection-failed events.
Also fix one tracepoint that was using an integer instead of the
corresponding enum value as the point type.
Signed-off-by: David Howells <dhowells@redhat.com>
Print a symbolic packet type name for each valid received packet in the
trace output, not just a number.
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the basic transmit DATA packet content size at 1412 bytes so that they
can be arbitrarily assembled into jumbo packets.
In the future, I'm thinking of moving to keeping a jumbo packet header at
the beginning of each packet in the Tx queue and creating the packet header
on the spot when kernel_sendmsg() is invoked. That way, jumbo packets can
be assembled on the spur of the moment for (re-)transmission.
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_send_call_packet() should use type in both its switch-statements
rather than using pkt->whdr.type. This might give the compiler an easier
job of uninitialised variable checking.
Signed-off-by: David Howells <dhowells@redhat.com>
Don't transmit an ACK if call->ackr_reason in unset. There's the
possibility of a race between recvmsg() sending an ACK and the background
processing thread trying to send the same one.
Signed-off-by: David Howells <dhowells@redhat.com>
Make the retransmission algorithm use for-loops instead of do-loops and
move the counter increments into the for-statement increment slots.
Though the do-loops are slighly more efficient since there will be at least
one pass through the each loop, the counter increments are harder to get
right as the continue-statements skip them.
Without this, if there are any positive acks within the loop, the do-loop
will cycle forever because the counter increment is never done.
Signed-off-by: David Howells <dhowells@redhat.com>
The soft-ACK parser doesn't increment the pointer into the soft-ACK list,
resulting in the first ACK/NACK value being applied to all the relevant
packets in the Tx queue. This has the potential to miss retransmissions
and cause excessive retransmissions.
Fix this by incrementing the pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
If the last call on a client connection is release after the connection has
had a bunch of calls allocated but before any DATA packets are sent (so
that it's not yet marked RXRPC_CONN_EXPOSED), an assertion will happen in
rxrpc_disconnect_client_call().
af_rxrpc: Assertion failed - 1(0x1) >= 2(0x2) is false
------------[ cut here ]------------
kernel BUG at ../net/rxrpc/conn_client.c:753!
This is because it's expecting the conn to have been exposed and to have 2
or more refs - but this isn't necessarily the case.
Simply remove the assertion. This allows the conn to be moved into the
inactive state and deleted if it isn't resurrected before the final put is
called.
Signed-off-by: David Howells <dhowells@redhat.com>
Call rxrpc_release_call() on getting an error in rxrpc_new_client_call()
rather than trying to do the cleanup ourselves. This isn't a problem,
provided we set RXRPC_CALL_HAS_USERID only if we actually add the call to
the calls tree as cleanup code fragments that would otherwise cause
problems are conditional.
Without this, we miss some of the cleanup.
Signed-off-by: David Howells <dhowells@redhat.com>
In rxrpc_put_one_client_conn(), if a connection has RXRPC_CONN_COUNTED set
on it, then it's accounted for in rxrpc_nr_client_conns and may be on
various lists - and this is cleaned up correctly.
However, if the connection doesn't have RXRPC_CONN_COUNTED set on it, then
the put routine returns rather than just skipping the extra bit of cleanup.
Fix this by making the extra bit of clean up conditional instead and always
killing off the connection.
This manifests itself as connections with a zero usage count hanging around
in /proc/net/rxrpc_conns because the connection allocated, but discarded,
due to a race with another process that set up a parallel connection, which
was then shared instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Purge the queue of to_be_accepted calls on socket release. Note that
purging sock_calls doesn't release the ref owned by to_be_accepted.
Probably the sock_calls list is redundant given a purges of the recvmsg_q,
the to_be_accepted queue and the calls tree.
Signed-off-by: David Howells <dhowells@redhat.com>
Record calls that need to be accepted using sk_acceptq_added() otherwise
the backlog counter goes negative because sk_acceptq_removed() is called.
This causes the preallocator to malfunction.
Calls that are preaccepted by AFS within the kernel aren't affected by
this.
Signed-off-by: David Howells <dhowells@redhat.com>
The code for determining the last packet in rxrpc_recvmsg_data() has been
using the RXRPC_CALL_RX_LAST flag to determine if the rx_top pointer points
to the last packet or not. This isn't a good idea, however, as the input
code may be running simultaneously on another CPU and that sets the flag
*before* updating the top pointer.
Fix this by the following means:
(1) Restrict the use of RXRPC_CALL_RX_LAST to the input routines only.
There's otherwise a synchronisation problem between detecting the flag
and checking tx_top. This could probably be dealt with by appropriate
application of memory barriers, but there's a simpler way.
(2) Set RXRPC_CALL_RX_LAST after setting rx_top.
(3) Make rxrpc_rotate_rx_window() consult the flags header field of the
DATA packet it's about to discard to see if that was the last packet.
Use this as the basis for ending the Rx phase. This shouldn't be a
problem because the recvmsg side of things is guaranteed to see the
packets in order.
(4) Make rxrpc_recvmsg_data() return 1 to indicate the end of the data if:
(a) the packet it has just processed is marked as RXRPC_LAST_PACKET
(b) the call's Rx phase has been ended.
Signed-off-by: David Howells <dhowells@redhat.com>
Move the check of rx_pkt_offset from rxrpc_locate_data() to the caller,
rxrpc_recvmsg_data(), so that it's more clear what's going on there.
Signed-off-by: David Howells <dhowells@redhat.com>
Add CONFIG_AF_RXRPC_IPV6 and make the IPv6 support code conditional on it.
This is then made conditional on CONFIG_IPV6.
Without this, the following can be seen:
net/built-in.o: In function `rxrpc_init_peer':
>> peer_object.c:(.text+0x18c3c8): undefined reference to `ip6_route_output_flags'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few places where an IE that matches not only the EID, but
also other bytes inside the element, needs to be found. To simplify
that and reduce the amount of similar code, implement a new helper
function to match the EID and an extra array of bytes.
Additionally, simplify cfg80211_find_vendor_ie() by using the new
match function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In 46fa38e84b ("mac80211: allow software PS-Poll/U-APSD with
AP_LINK_PS"), Johannes allowed to use mac80211's code for handling
stations that go to PS or send PS-Poll / uAPSD trigger frames for
devices that enable RSS.
This means that mac80211 doesn't look at frames anymore but rather
relies on a notification that will come from the device when a PS
transition occurs or when a PS-Poll / trigger frame is detected by
the device.
iwlwifi will need this capability but still needs mac80211 to take
care of the TIM IE. Today, if a driver sets AP_LINK_PS, mac80211
will not update the TIM IE. Change mac80211 to check existence of
the set_tim driver callback rather than using AP_LINK_PS to decide
if the driver handles the TIM IE internally or not.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the 2-bytes Qualcomm tag that gigabit switches such as
the QCA8337/N might insert when receiving packets, or that we need
to insert while targeting specific switch ports. The tag is inserted
directly behind the ethernet header.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ip_rcv_finish() calls l3mdev_ip_rcv(). On any VRF except
the global VRF, this replaces skb->dev with the VRF master interface.
When calling ip_route_input_noref() from here, the checks for forwarding
look at this master device instead of the initial ingress interface.
This will allow packets to be routed which normally would be dropped.
For example, an interface that is not assigned an IP address should
drop packets, but because the checking is against the master device, the
packet will be forwarded.
The fix here is to still call l3mdev_ip_rcv(), but remember the initial
net_device. This is passed to the other functions within ip_rcv_finish,
so they still see the original interface.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix reference counting for last_bonding_candidate, by Sven Eckelmann
- Fix head room reservation for ELP packets, by Linus Luessing
-----BEGIN PGP SIGNATURE-----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=mHPX
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20160914' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfix patches:
- Fix reference counting for last_bonding_candidate, by Sven Eckelmann
- Fix head room reservation for ELP packets, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb replaces another one in ooo queue, I forgot to also
update tp->ooo_last_skb as well, if the replaced skb was the last one
in the queue.
To fix this, we simply can re-use the code that runs after an insertion,
trying to merge skbs at the right of current skb.
This not only fixes the bug, but also remove all small skbs that might
be a subset of the new one.
Example:
We receive segments 2001:3001, 4001:5001
Then we receive 2001:8001 : We should replace 2001:3001 with the big
skb, but also remove 4001:50001 from the queue to save space.
packetdrill test demonstrating the bug
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
+0.100 < . 1:1(0) ack 1 win 1024
+0 accept(3, ..., ...) = 4
+0.01 < . 1001:2001(1000) ack 1 win 1024
+0 > . 1:1(0) ack 1 <nop,nop, sack 1001:2001>
+0.01 < . 1001:3001(2000) ack 1 win 1024
+0 > . 1:1(0) ack 1 <nop,nop, sack 1001:2001 1001:3001>
Fixes: 9f5afeae51 ("tcp: use an RB tree for ooo receive queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQIVAwUAV9h/5PSw1s6N8H32AQLJCQ//RFbu0SNSoJnnZbOTwkxBaGYnGg4KbNVt
iR4zumQfFssyYr7WcH1S6kuPzM/dJfjkRYqollyUGCEfnWyDwyfnjM9Na9PQoZ9F
k7xnbim8N65njHLdGF6QMhenmoRXSBVCN2E0uPTbBXurFHJ8ZgQQs+DhogalvGUl
2TL/aMdpqRoo1Vg0/APVOKeLGqgHEhrXxelTZB/74IXyYT+rzjfzu+ZfwxUAijsM
d+FBSwY+D8RYSV4LXQzMNNFCwNORbG2Rse2nEqd7bVqdVywWsuhbgeESjx1Y3+ge
/mofVyxrpoblT9qsScbISbIQEe6cLxRiQgQHEudennRI2/3EbpNSijhNFWVon2Em
NAa7r+tfOPtVx5JTL9NyvwtrXPfAgDi7Stpml3Yhhr/CjRHYK9kfKysowMXL5vOz
NHD0fUozNLecpGCmdxG+alwf5BJ5q9DRPP7bI7KE/4FfVsYe8bO6pQ9G+myeP/A4
h8DuvK4xSJUEpEa5dpDLA1wSC2XH5PgYdXIr2DFBaFjllIdf1cGNKKIYRF2eIX/I
obVD7c72oZV1kIK3URTLJpE+CdA4KgTFuL3YqIxquA2Iedb1t2uOrQcp4WwaWf7V
REY9KbBn1F0+yJfO3Fjckerzle+MlAmrAHQpkZUduo5JzdRm3DY++YzswXQT5Fpr
8S3T30nwY0k=
=T1wh
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160913-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Support IPv6
Here is a set of patches that add IPv6 support. They need to be applied on
top of the just-posted miscellaneous fix patches. They are:
(1) Make autobinding of an unconnected socket work when sendmsg() is
called to initiate a client call.
(2) Don't specify the protocol when creating the client socket, but rather
take the default instead.
(3) Use rxrpc_extract_addr_from_skb() in a couple of places that were
doing the same thing manually. This allows the IPv6 address
extraction to be done in fewer places.
(4) Add IPv6 support. With this, calls can be made to IPv6 servers from
userspace AF_RXRPC programs; AFS, however, can't use IPv6 yet as the
RPC calls need to be upgradeable.
====================
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=vHfH
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160913-1' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Miscellaneous fixes
Here's a set of miscellaneous fix patches. There are a couple of points of
note:
(1) There is one non-fix patch that adjusts the call ref tracking
tracepoint to make kernel API-held refs on calls more obvious. This
is a prerequisite for the patch that fixes prealloc refcounting.
(2) The final patch alters how jumbo packets that partially exceed the
receive window are handled. Previously, space was being left in the
Rx buffer for them, but this significantly hurts performance as the Rx
window can't be increased to match the OpenAFS Tx window size.
Instead, the excess subpackets are discarded and an EXCEEDS_WINDOW ACK
is generated for the first. To avoid the problem of someone trying to
run the kernel out of space by feeding the kernel a series of
overlapping maximal jumbo packets, we stop allowing jumbo packets on a
call if we encounter more than three jumbo packets with duplicate or
excessive subpackets.
====================
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* better mesh path fixing, from Thomas
* fix TIM IE recalculation after sending frames
to a sleeping station, from Felix
* fix sequence number assignment while sending
frames to a sleeping station, also from Felix
* validate number of probe response CSA counter
offsets, fixing a copy/paste bug (from myself)
-----BEGIN PGP SIGNATURE-----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=xzhM
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more fixes:
* better mesh path fixing, from Thomas
* fix TIM IE recalculation after sending frames
to a sleeping station, from Felix
* fix sequence number assignment while sending
frames to a sleeping station, also from Felix
* validate number of probe response CSA counter
offsets, fixing a copy/paste bug (from myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ovs kernel data path currently defers the execution of all
recirc actions until stack utilization is at a minimum.
This is too limiting for some packet forwarding scenarios due to
the small size of the deferred action FIFO (10 entries). For
example, broadcast traffic sent out more than 10 ports with
recirculation results in packet drops when the deferred action
FIFO becomes full, as reported here:
http://openvswitch.org/pipermail/dev/2016-March/067672.html
Since the current recursion depth is available (it is already tracked
by the exec_actions_level pcpu variable), we can use it to determine
whether to execute recirculation actions immediately (safe when
recursion depth is low) or defer execution until more stack space is
available.
With this change, the deferred action fifo size becomes a non-issue
for currently failing scenarios because it is no longer used when
there are three or fewer recursions through ovs_execute_actions().
Suggested-by: Pravin Shelar <pshelar@ovn.org>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c3f8324188 "net: Add full IPv6 addresses to flow_keys" added an
unused instance of struct flow_dissector_key_addrs into struct fl_flow_key,
remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the definitions for src/dst udp/tcp port masks and use
them when setting && dumping the relevant keys.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action is intended to be an upgrade from a usability perspective
from pedit (as well as operational debugability).
Compare this:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action pedit munge offset -14 u8 set 0x02 \
munge offset -13 u8 set 0x15 \
munge offset -12 u8 set 0x15 \
munge offset -11 u8 set 0x15 \
munge offset -10 u16 set 0x1515 \
pipe
to:
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbmod dmac 02:15:15:15:15:15
Also try to do a MAC address swap with pedit or worse
try to debug a policy with destination mac, source mac and
etherype. Then make few rules out of those and you'll get my point.
In the future common use cases on pedit can be migrated to this action
(as an example different fields in ip v4/6, transports like tcp/udp/sctp
etc). For this first cut, this allows modifying basic ethernet header.
The most important ethernet use case at the moment is when redirecting or
mirroring packets to a remote machine. The dst mac address needs a re-write
so that it doesnt get dropped or confuse an interconnecting (learning) switch
or dropped by a target machine (which looks at the dst mac). And at times
when flipping back the packet a swap of the MAC addresses is needed.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a small skb_at_tc_ingress() helper for testing for ingress, so
make use of it. cls_bpf already uses it and so should act_bpf.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_mac_header_was_set() test in cls_bpf's and act_bpf's fast-path is
actually unnecessary and can be removed altogether. This was added by
commit a166151cbe ("bpf: fix bpf helpers to use skb->mac_header relative
offsets"), which was later on improved by 3431205e03 ("bpf: make programs
see skb->data == L2 for ingress and egress"). We're always guaranteed to
have valid mac header at the time we invoke cls_bpf_classify() or tcf_bpf().
Reason is that since 6d1ccff627 ("net: reset mac header in dev_start_xmit()")
we do skb_reset_mac_header() in __dev_queue_xmit() before we could call
into sch_handle_egress() or any subsequent enqueue. sch_handle_ingress()
always sees a valid mac header as well (things like skb_reset_mac_len()
would badly fail otherwise). Thus, drop the unnecessary test in classifier
and action case.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rcu_read_lock protection from tunnel_key_dump and use
rtnl_dereference, dump operation is protected by rtnl lock.
Also, remove rcu_read_lock from tunnel_key_release and use
rcu_dereference_protected.
Both operations are running exclusively and a writer couldn't modify
t->params while those functions are executed.
Fixes: 54d94fd89d90 ('net/sched: Introduce act_tunnel_key')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For an array, there's no need to use &array, so just use the
plain wiphy->addresses[i].addr here to silence smatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on consecutive msdu failures, mac80211 triggers CQM packet-loss
mechanism. Drivers like ath10k that have its own connection monitoring
algorithm, offloaded to firmware for triggering station kickout. In case
of station kickout, driver will report low ack status by mac80211 API
(ieee80211_report_low_ack).
This flag will enable the driver to completely rely on firmware events
for station kickout and bypass mac80211 packet loss mechanism.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No drivers implement this, relying either on the recursive
directory removal to remove their debugfs, or not having any
to start with. Remove the dead driver callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If chanctx is derived as container_of() from a non-NULL pointer,
it can't ever be NULL. Since we checked conf before, that's true
here, so remove the useless NULL check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The next line overwrites this assignment, so remove it; there's
no real value in using it for the next assignment either.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few instances were found where we didn't check them, add the
missing checks even though they'll probably never trigger as
the message should be large enough here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the message got full during nla_nest_start(), it can return
NULL. None of the cases here seem like that can really happen,
but check the return value nonetheless.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Passing the 'info' pointer where a 'info->aborted' is expected will
always lead to tracing to erroneously record that the scan was aborted,
fix that by passing the correct info->aborted. The remaining data will
be collected in cfg80211, so I haven't duplicated it here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the unlikely situation that the supplicant has negotiated
admission for the background AC (which it has no reason to as
it's not supposed to be requiring admission control to start
with, and we'd ignore such a requirement anyway), the loop
here may terminate with non_acm_ac == 4, which leads to an
array overrun.
Check this explicitly just for completeness.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no point in allowing connect keys when one of them
isn't also configured as the TX key, it would just confuse
drivers and probably cause them to pick something for TX.
Disallow this confusing and erroneous configuration.
As wpa_supplicant will always send NL80211_ATTR_KEYS, even
when there are no keys inside, allow that and treat it as
though the attribute isn't present at all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mac80211 doesn't currently support TSIDs 8-15 which can
only be used after QoS TSPEC negotiation (and not even after
WMM negotiation), reject attempts to set up aggregation
sessions for them, which might confuse drivers. In mac80211
we do correctly handle that, but the TSIDs should never get
used anyway, and drivers might not be able to handle it.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The A-MSDU TX code (within TXQs) didn't always check the return value
of skb_linearize() properly, resulting in potentially passing a frag-
list SKB down to the driver even when it said it can't handle it. Fix
that.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add IPv6 support to AF_RXRPC. With this, AF_RXRPC sockets can be created:
service = socket(AF_RXRPC, SOCK_DGRAM, PF_INET6);
instead of:
service = socket(AF_RXRPC, SOCK_DGRAM, PF_INET);
The AFS filesystem doesn't support IPv6 at the moment, though, since that
requires upgrades to some of the RPC calls.
Note that a good portion of this patch is replacing "%pI4:%u" in print
statements with "%pISpc" which is able to handle both protocols and print
the port.
Signed-off-by: David Howells <dhowells@redhat.com>
There are two places that want to transmit a packet in response to one just
received and manually pick the address to reply to out of the sk_buff.
Make them use rxrpc_extract_addr_from_skb() instead so that IPv6 is handled
automatically.
Signed-off-by: David Howells <dhowells@redhat.com>
Create an address for sendmsg() to bind unbound socket with rather than
using a completely blank address otherwise the transport socket creation
will fail because it will try to use address family 0.
We use the address family specified in the protocol argument when the
AF_RXRPC socket was created and SOCK_DGRAM as the default. For anything
else, bind() must be used.
Signed-off-by: David Howells <dhowells@redhat.com>
call->rx_winsize should be initialised to the sysctl setting and the sysctl
setting should be limited to the maximum we want to permit. Further, we
need to place this in the ACK info instead of the sysctl setting.
Furthermore, discard the idea of accepting the subpackets of a jumbo packet
that lie beyond the receive window when the first packet of the jumbo is
within the window. Just discard the excess subpackets instead. This
allows the receive window to be opened up right to the buffer size less one
for the dead slot.
Signed-off-by: David Howells <dhowells@redhat.com>
The preallocated call buffer holds a ref on the calls within that buffer.
The ref was being released in the wrong place - it worked okay for incoming
calls to the AFS cache manager service, but doesn't work right for incoming
calls to a userspace service.
Instead of releasing an extra ref service calls in rxrpc_release_call(),
the ref needs to be released during the acceptance/rejectance process. To
this end:
(1) The prealloc ref is now normally released during
rxrpc_new_incoming_call().
(2) For preallocated kernel API calls, the kernel API's ref needs to be
released when the call is discarded on socket close.
(3) We shouldn't take a second ref in rxrpc_accept_call().
(4) rxrpc_recvmsg_new_call() needs to get a ref of its own when it adds
the call to the to_be_accepted socket queue.
In doing (4) above, we would prefer not to put the call's refcount down to
0 as that entails doing cleanup in softirq context, but it's unlikely as
there are several refs held elsewhere, at least one of which must be put by
someone in process context calling rxrpc_release_call(). However, it's not
a problem if we do have to do that.
Signed-off-by: David Howells <dhowells@redhat.com>
Adjust the call ref tracepoint to show references held on a call by the
kernel API separately as much as possible and add an additional trace to at
the allocation point from the preallocation buffer for an incoming call.
Note that this doesn't show the allocation of a client call for the kernel
separately at the moment.
Signed-off-by: David Howells <dhowells@redhat.com>
Allow tx_winsize to grow when the ACK info packet shows a larger receive
window at the other end rather than only permitting it to shrink.
Signed-off-by: David Howells <dhowells@redhat.com>
skb->len should be used rather than skb->data_len when referring to the
amount of data in a packet. This will only cause a malfunction in the
following cases:
(1) We receive a jumbo packet (validation and splitting both are wrong).
(2) We see if there's extra ACK info in an ACK packet (we think it's not
there and just ignore it).
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_recvmsg() needs to make sure that the call it has just been
processing gets requeued for further attention if the buffer has been
filled and there's more data to be consumed. The softirq producer only
queues the call and wakes the socket if it fills the first slot in the
window, so userspace might end up sleeping forever otherwise, despite there
being data available.
This is not a problem provided the userspace buffer is big enough or it
empties the buffer completely before more data comes in.
Signed-off-by: David Howells <dhowells@redhat.com>
We need to wake up the sender when Tx window rotation due to an incoming
ACK makes space in the buffer otherwise the sender is liable to just hang
endlessly.
This problem isn't noticeable if the Tx phase transfers no more than will
fit in a single window or the Tx window rotates fast enough that it doesn't
get full.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells
Douglas Caetano dos Santos
Eric Dumazet
Marcelo Ricardo Leitner
WANG Cong
David S. Miller
Pablo Neira Ayuso
Gao Feng
Liping Zhang
Laura Garcia Liebana
Eric W. Biederman
Andrey Vagin
Trond Myklebust
Linus Torvalds
Michał Narajowski
Arek Lichwa
Yuchung Cheng
Shmulik Ladkani
Shmulik Ladkani
Jakub Kicinski
Florian Westphal
Nicolas Dichtel
Nikolay Aleksandrov
Neal Cardwell
Soheil Hassas Yeganeh
Jamal Hadi Salim
Daniel Borkmann
pravin shelar
John Crispin
Herbert Xu
Vincent Bernat
Roman Mashak
Steffen Klassert
Johannes Weiner
Szymon Janc
Wei Yongjun
Frédéric Dalleau
Marcel Holtmann
Johan Hedberg
Aristeu Rozanski
Alexander Aring
David Vrabel
Chuck Lever
Andy Adamson
Amitoj Kaur Chawla
Ilan Tayari
Christophe Jaillet
Mahesh Bandewar
Nogah Frankel
Thadeu Lima de Souza Cascardo
Xin Long
Alexei Starovoitov
Julia Lawall
Alan Cox
phil.turnbull@oracle.com
Luca Coelho
Emmanuel Grumbach
Mark Tomlinson
Lance Richardson
Or Gerlitz
Hadar Hen Zion
Johannes Berg
Rajkumar Manoharan