The spi controller supports 44-bit address space on AXI in DMA mode,
so set dma_addr_t width to 44-bit to avoid using a swiotlb mapping.
In addition, if dma_map_single fails, it should return immediately
instead of continuing doing the DMA operation which bases on invalid
address.
This fixes the following crash which occurs in reading a big block
from flash:
[ 123.633577] zynqmp-qspi ff0f0000.spi: swiotlb buffer is full (sz: 4194304 bytes), total 32768 (slots), used 0 (slots)
[ 123.644230] zynqmp-qspi ff0f0000.spi: ERR:rxdma:memory not mapped
[ 123.784625] Unable to handle kernel paging request at virtual address 00000000003fffc0
[ 123.792536] Mem abort info:
[ 123.795313] ESR = 0x96000145
[ 123.798351] EC = 0x25: DABT (current EL), IL = 32 bits
[ 123.803655] SET = 0, FnV = 0
[ 123.806693] EA = 0, S1PTW = 0
[ 123.809818] Data abort info:
[ 123.812683] ISV = 0, ISS = 0x00000145
[ 123.816503] CM = 1, WnR = 1
[ 123.819455] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000805047000
[ 123.825887] [00000000003fffc0] pgd=0000000803b45003, p4d=0000000803b45003, pud=0000000000000000
[ 123.834586] Internal error: Oops: 96000145 [#1] PREEMPT SMP
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-6-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When handling op->addr, it is using the buffer "tmpbuf" which has been
freed. This will trigger a use-after-free KASAN warning. Let's use
temporary variables to store op->addr.val and op->cmd.opcode to fix
this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-5-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During a transfer the driver filled the fifo with 4bytes,
even if the data that needs to be transfer is less that 4bytes.
This resulted in slab-out-of-bounds bug in KernelAddressSanitizer.
This patch resolves slab-out-of-bounds bug by filling the fifo
with the number of bytes that needs to transferred.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-4-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After calling platform_set_drvdata(pdev, xqspi) in probe, the return
value of dev_get_drvdata(dev) is a pointer to struct zynqmp_qspi but
not struct spi_controller. A wrong structure type passing to the
functions spi_controller_suspend/resume will hang the system.
And we should check the return value of spi_controller_suspend, if
an error is returned, return it to PM subsystem to stop suspend.
Also, GQSPI_EN_MASK should be written to GQSPI_EN_OFST to enable
the spi controller in zynqmp_qspi_resume since it was disabled in
zynqmp_qspi_suspend before.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-3-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The clks "pclk" and "ref_clk" are enabled twice during the probe. The
first time is in the function zynqmp_qspi_probe and the second time is
in zynqmp_qspi_setup_op which is called by devm_spi_register_controller.
Then calling zynqmp_qspi_remove (rmmod this module) to disable these clks
will trigger a warning as below:
[ 309.124604] Unpreparing enabled qspi_ref
[ 309.128641] WARNING: CPU: 1 PID: 537 at drivers/clk/clk.c:824 clk_core_unprepare+0x108/0x110
Since pm_runtime works now, clks can be enabled/disabled by calling
zynqmp_runtime_suspend/resume. So we don't need to enable these clks
explicitly in zynqmp_qspi_setup_op. Remove them to fix this issue.
And remove clk enabling/disabling in zynqmp_qspi_resume because there is
no spi transfer operation so enabling ref_clk is redundant meanwhile pclk
is not disabled for it is shared with other peripherals.
Furthermore replace clk_enable/disable with clk_prepare_enable and
clk_disable_unprepare in runtime_suspend/resume functions.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-2-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a PM usage counter decrement after zynqmp_qspi_init_hw()
without any refcount increment, which leads to refcount leak.Add
a refcount increment to balance the refcount. Also set
auto_runtime_pm to resume suspended spi controller.
Fixes: 9e3a000362 ("spi: zynqmp: Add pm runtime support")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Tested-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210415074644.24646-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing unlock before return from function zynqmp_qspi_exec_op()
in the error handling case.
Fixes: a0f65be6e8 ("spi: spi-zynqmp-gqspi: add mutex locking for exec_op")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210412160025.194171-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When starting a read operation, we should call zynqmp_qspi_setuprxdma
first to set xqspi->mode according to xqspi->bytes_to_receive and
to calculate correct xqspi->dma_rx_bytes. Then in the function
zynqmp_qspi_fillgenfifo, generate the appropriate command with
operating mode and bytes to transfer, and fill the GENFIFO with
the command to perform the read operation.
Calling zynqmp_qspi_fillgenfifo before zynqmp_qspi_setuprxdma will
result in incorrect transfer length and operating mode. So change
the calling order to fix this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-5-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a data corruption issue that occurs in the reading operation
(cmd:0x6c) when transmitting common data as dummy circles.
The gqspi controller has the functionality to send dummy clock circles.
When writing data with the fields [receive, transmit, data_xfer] = [0,0,1]
to the Generic FIFO, and configuring the correct SPI mode, the controller
will transmit dummy circles.
So let's switch to hardware dummy cycles transfer to fix this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-4-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-mem framework has no locking to prevent ctlr->mem_ops->exec_op
from concurrency. So add the locking to zynqmp_qspi_exec_op.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-3-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When Ctrl+C occurs during the process of zynqmp_qspi_exec_op, the function
wait_for_completion_interruptible_timeout will return a non-zero value
-ERESTARTSYS immediately. This will disrupt the SPI memory operation
because the data transmitting may begin before the command or address
transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
This patch fixes the error as below:
root@xilinx-zynqmp:~# flash_erase /dev/mtd3 0 0
Erasing 4 Kibyte @ 3d000 -- 4 % complete
(Press Ctrl+C)
[ 169.581911] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 170.585907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 171.589910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 172.593910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.597907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.603480] spi-nor spi0.0: Erase operation failed.
[ 173.608368] spi-nor spi0.0: Attempted to modify a protected sector.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-2-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavecs' not described in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavebus' not described in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashcs' description in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashbus' description in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:902: warning: Function parameter or member 'dev' not described in 'zynqmp_qspi_suspend'
drivers/spi/spi-zynqmp-gqspi.c:902: warning: Excess function parameter '_dev' description in 'zynqmp_qspi_suspend'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-11-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use direct function call instead of using eemi ops for fpga related
APIs. Also remove eemi ops structure.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Link: https://lore.kernel.org/r/1587761887-4279-21-git-send-email-jolly.shah@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the public interface for chipselect, there is always an entry
commented as "Dummy generic FIFO entry" pushed down to the fifo right
after the activate/deactivate command. The dummy entry is 0x0,
irregardless if the intention was to activate or deactive the cs. This
causes the cs line to glitch rather than beeing activated in the case
when there was an activate command.
This has been observed on oscilloscope, and have caused problems for at
least one specific flash device type connected to the qspi port. After
the change the glitch is gone and cs goes active when intended.
The reason why this worked before (except for the glitch) was because
when sending the actual data, the CS bits are once again set. Since
most flashes uses mode 0, there is always a half clk period anyway for
cs to clk active setup time. If someone would rely on timing from a
chip_select call to a transfer_one, it would fail though.
It is unknown why the dummy entry was there in the first place, git log
seems to be of no help in this case. The reference manual gives no
indication of the necessity of this. In fact the lower 8 bits are a
setup (or hold in case of deactivate) time expressed in cycles. So this
should not be needed to fulfill any setup/hold timings.
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-35-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-42-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation either version 2 of the
license or at your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170857.824091446@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Missing include:
drivers/spi/spi-zynqmp-gqspi.c:1025:13: error: implicit declaration of
function 'zynqmp_pm_get_eemi_ops'; did you mean
'zynqmp_process_dma_irq'? [-Werror=implicit-function-declaration]
Fixes: 3d03137864 ('drivers: Defer probe if firmware is not ready')
Cc: Rajan Vaja <rajan.vaja@xilinx.com>
Cc: Jolly Shah <jollys@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Driver needs ZynqMP firmware interface to call EEMI
APIs. In case firmware is not ready, dependent drivers
should wait until the firmware is ready.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The if pclk enable fails the refclk is not disabled.
Fix the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a missing break statement here so selecting both only selects
upper.
Fixes: dfe11a11d5 ('spi: Add support for Zynq Ultrascale+ MPSoC GQSPI controller')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for GQSPI controller driver used by
Zynq Ultrascale+ MPSoC
Signed-off-by: Ranjit Waghmode <ranjit.waghmode@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quanyang Wang
Amit Kumar Mahapatra
Dinghao Liu
Wei Yongjun
Lee Jones
Rajan Vaja
Thommy Jakobsson
YueHaibing
Stephen Boyd
Thomas Gleixner
Olof Johansson
Wolfram Sang
Naga Sureshkumar Relli
Shubhrajyoti Datta
Geliang Tang
Dan Carpenter
Mark Brown
Ranjit Waghmode