When the last ftrace_ops is unregistered, all the function records should
have a zeroed flags value. Make sure that is the case when the last ftrace_ops
is unregistered.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Allowing function callbacks to declare their own trampolines requires
that each ftrace_ops that has a trampoline must have some sort of
accounting that keeps track of which ops has a trampoline attached
to a record.
The easy way to solve this was to add a "tramp_hash" that created a
hash entry for every function that a ops uses with a trampoline.
But since we can have literally tens of thousands of functions being
traced, that means we need tens of thousands of descriptors to map
the ops to the function in the hash. This is quite expensive and
can cause enabling and disabling the function graph tracer to take
some time to start and stop. It can take up to several seconds to
disable or enable all functions in the function graph tracer for this
reason.
The better approach albeit more complex, is to keep track of how ops
are being enabled and disabled, and use that along with the counting
of the number of ops attached to records, to determive what ops has
a trampoline attached to a record at enabling and disabling of
tracing.
To do this, the tramp_hash has been replaced with an old_filter_hash
and old_notrace_hash, which get the copy of the ops filter_hash and
notrace_hash respectively. The old hashes is kept until the ops has
been modified or removed and the old hashes are used with the logic
of the accounting to determine the ops that have the trampoline of
a record. The reason this has less of a footprint is due to the trick
that an "empty" hash in the filter_hash means "all functions" and
an empty hash in the notrace hash means "no functions" in the hash.
This is much more efficienct, doesn't have the delay, and takes up
much less memory, as we do not need to map all the functions but
just figure out which functions are mapped at the time it is
enabled or disabled.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add three new flags for ftrace_ops:
FTRACE_OPS_FL_ADDING
FTRACE_OPS_FL_REMOVING
FTRACE_OPS_FL_MODIFYING
These will be set for the ftrace_ops when they are first added
to the function tracing, being removed from function tracing
or just having their functions changed from function tracing,
respectively.
This will be needed to remove the tramp_hash, which can grow quite
big. The tramp_hash is used to note what functions a ftrace_ops
is using a trampoline for. Denoting which ftrace_ops is being
modified, will allow us to use the ftrace_ops hashes themselves,
which are much smaller as they have a global flag to denote if
a ftrace_ops is tracing all functions, as well as a notrace hash
if the ftrace_ops is tracing all but a few. The tramp_hash just
creates a hash item for every function, which can go into the 10s
of thousands if all functions are using the ftrace_ops trampoline.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When dumping the enabled_functions, use the first op that is
found with a trampoline to the record, as there should only be
one, as only one ops can be registered to a function that has
a trampoline.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ftrace_hash_move() currently frees the old hash that is passed to it
after replacing the pointer with the new hash. Instead of having the
function do that chore, have the caller perform the free.
This lets the ftrace_hash_move() be used a bit more freely, which
is needed for changing the way the trampoline logic is done.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The clean up that adds the helper function ftrace_ops_get_func()
caused the default function to not change when DYNAMIC_FTRACE was not
set and no ftrace_ops were registered. Although static tracing is
not very useful (not having DYNAMIC_FTRACE set), it is still supported
and we don't want to break it.
Clean up the if statement even more to specifically have the default
function call ftrace_stub when no ftrace_ops are registered. This
fixes the small bug for static tracing as well as makes the code a
bit more understandable.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add the helper function to what the mcount trampoline is to call
for a ftrace_ops function. This helper will be used by arch code
in the future to set up dynamic trampolines. But as this does the
same tests that are performed in choosing what function to call for
the default mcount trampoline, might as well use it to clean up
the existing code.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Instead of using the generic list function for callbacks that
are not recursive, call a new helper function from the mcount
trampoline called ftrace_ops_recur_func() that will do the recursion
checking for the callback.
This eliminates an indirection as well as will help in future code
that will use dynamically allocated trampolines.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In __ftrace_replace_code(), when converting the call to a nop in a function
it needs to compare against the "curr" (current) value of the ftrace ops, and
not the "new" one. It currently does not affect x86 which is the only arch
to do the trampolines with function graph tracer, but when other archs that do
depend on this code implement the function graph trampoline, it can crash.
Here's an example when ARM uses the trampolines (in the future):
------------[ cut here ]------------
WARNING: CPU: 0 PID: 9 at kernel/trace/ftrace.c:1716 ftrace_bug+0x17c/0x1f4()
Modules linked in: omap_rng rng_core ipv6
CPU: 0 PID: 9 Comm: migration/0 Not tainted 3.16.0-test-10959-gf0094b28f303-dirty #52
[<c02188f4>] (unwind_backtrace) from [<c021343c>] (show_stack+0x20/0x24)
[<c021343c>] (show_stack) from [<c095a674>] (dump_stack+0x78/0x94)
[<c095a674>] (dump_stack) from [<c02532a0>] (warn_slowpath_common+0x7c/0x9c)
[<c02532a0>] (warn_slowpath_common) from [<c02532ec>] (warn_slowpath_null+0x2c/0x34)
[<c02532ec>] (warn_slowpath_null) from [<c02cbac4>] (ftrace_bug+0x17c/0x1f4)
[<c02cbac4>] (ftrace_bug) from [<c02cc44c>] (ftrace_replace_code+0x80/0x9c)
[<c02cc44c>] (ftrace_replace_code) from [<c02cc658>] (ftrace_modify_all_code+0xb8/0x164)
[<c02cc658>] (ftrace_modify_all_code) from [<c02cc718>] (__ftrace_modify_code+0x14/0x1c)
[<c02cc718>] (__ftrace_modify_code) from [<c02c7244>] (multi_cpu_stop+0xf4/0x134)
[<c02c7244>] (multi_cpu_stop) from [<c02c6e90>] (cpu_stopper_thread+0x54/0x130)
[<c02c6e90>] (cpu_stopper_thread) from [<c0271cd4>] (smpboot_thread_fn+0x1ac/0x1bc)
[<c0271cd4>] (smpboot_thread_fn) from [<c026ddf0>] (kthread+0xe0/0xfc)
[<c026ddf0>] (kthread) from [<c020f318>] (ret_from_fork+0x14/0x20)
---[ end trace dc9ce72c5b617d8f ]---
[ 65.047264] ftrace failed to modify [<c0208580>] asm_do_IRQ+0x10/0x1c
[ 65.054070] actual: 85:1b:00:eb
Fixes: 7413af1fb7 "ftrace: Make get_ftrace_addr() and get_ftrace_addr_old() global"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The latest rewrite of ftrace removed the separate ftrace_ops of
the function tracer and the function graph tracer and had them
share the same ftrace_ops. This simplified the accounting by removing
the multiple layers of functions called, where the global_ops func
would call a special list that would iterate over the other ops that
were registered within it (like function and function graph), which
itself was registered to the ftrace ops list of all functions
currently active. If that sounds confusing, the code that implemented
it was also confusing and its removal is a good thing.
The problem with this change was that it assumed that the function
and function graph tracer can never be used at the same time.
This is mostly true, but there is an exception. That is when the
function profiler uses the function graph tracer to profile.
The function profiler can be activated the same time as the function
tracer, and this breaks the assumption and the result is that ftrace
will crash (it detects the error and shuts itself down, it does not
cause a kernel oops).
To solve this issue, a previous change allowed the hash tables
for the functions traced by a ftrace_ops to be a pointer and let
multiple ftrace_ops share the same hash. This allows the function
and function_graph tracer to have separate ftrace_ops, but still
share the hash, which is what is done.
Now the function and function graph tracers have separate ftrace_ops
again, and the function tracer can be run while the function_profile
is active.
Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Now that a ftrace_hash can be shared by multiple ftrace_ops, they can dec
the rec->flags by more than once (one per those that share the ftrace_hash).
This means that the tramp_hash may not have a hash item when it was added.
For example, if two ftrace_ops share a hash for a ftrace record, and the
first ops has a trampoline, when it adds itself it will set the rec->flags
TRAMP flag and increments its nr_trampolines counter. When the second ops
is added, it must clear that tramp flag but also decrement the other ops
that shares its hash. As the update to the function callbacks has not yet
been performed, the other ops will not have the tramp hash set yet and it
can not be used to know to decrement its nr_trampolines.
Luckily, the tramp_hash does not need to be used. As the ftrace_mutex is
held, a ops with a trampoline to a record during an update of another ops
that shares the record will have its func_hash pointing to it. Since a
trampoline can only be set for a record if only one ops is attached to it,
we can just check if the record has a trampoline (the FTRACE_FL_TRAMP flag
is set) and then find the ops that has this record in its hashes.
Also added some output to help debug when things go wrong.
Cc: stable@vger.kernel.org # 3.16+ (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When updating what an ftrace_ops traces, if it is registered (that is,
actively tracing), and that ftrace_ops uses the shared global_ops
local_hash, then we need to update all tracers that are active and
also share the global_ops' ftrace_hash_ops.
Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently the top level debug file system function tracer shares its
ftrace_ops with the function graph tracer. This was thought to be fine
because the tracers are not used together, as one can only enable
function or function_graph tracer in the current_tracer file.
But that assumption proved to be incorrect. The function profiler
can use the function graph tracer when function tracing is enabled.
Since all function graph users uses the function tracing ftrace_ops
this causes a conflict and when a user enables both function profiling
as well as the function tracer it will crash ftrace and disable it.
The quick solution so far is to move them as separate ftrace_ops like
it was earlier. The problem though is to synchronize the functions that
are traced because both function and function_graph tracer are limited
by the selections made in the set_ftrace_filter and set_ftrace_notrace
files.
To handle this, a new structure is made called ftrace_ops_hash. This
structure will now hold the filter_hash and notrace_hash, and the
ftrace_ops will point to this structure. That will allow two ftrace_ops
to share the same hashes.
Since most ftrace_ops do not share the hashes, and to keep allocation
simple, the ftrace_ops structure will include both a pointer to the
ftrace_ops_hash called func_hash, as well as the structure itself,
called local_hash. When the ops are registered, the func_hash pointer
will be initialized to point to the local_hash within the ftrace_ops
structure. Some of the ftrace internal ftrace_ops will be initialized
statically. This will allow for the function and function_graph tracer
to have separate ops but still share the same hash tables that determine
what functions they trace.
Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
to the ftrace function callback infrastructure. It's introducing a
way to allow different functions to call directly different trampolines
instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which always
had a different trampoline, but the function tracer trampoline was called
and did basically nothing, and then the function graph tracer trampoline
was called. The difference now, is that the function graph tracer
trampoline can be called directly if a function is only being traced by
the function graph trampoline. If function tracing is also happening on
the same function, the old way is still done.
The accounting for this takes up more memory when function graph tracing
is activated, as it needs to keep track of which functions it uses.
I have a new way that wont take as much memory, but it's not ready yet
for this merge window, and will have to wait for the next one.
Another big change was the removal of the ftrace_start/stop() calls that
were used by the suspend/resume code that stopped function tracing when
entering into suspend and resume paths. The stop of ftrace was done
because there was some function that would crash the system if one called
smp_processor_id()! The stop/start was a big hammer to solve the issue
at the time, which was when ftrace was first introduced into Linux.
Now ftrace has better infrastructure to debug such issues, and I found
the problem function and labeled it with "notrace" and function tracing
can now safely be activated all the way down into the guts of suspend
and resume.
Other changes include clean ups of uprobe code.
Clean up of the trace_seq() code.
And other various small fixes and clean ups to ftrace and tracing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT35zXAAoJEKQekfcNnQGuOz0H/38zqM0nLFhrgvz3EPk2UOjn
xqpX8qyb2V7TJZL+IqeXU2a5cQZl5ba0D4WtBGpxbTae3CJYiuQ87iKUNFoH0om5
FDpn80igb368k8V3qRdRsziKVCCf0XBd/NkHJXc0ZkfXGyzB2Ga4bBxALxp2gj9y
bnO+vKo6+tWYKG4hyQb4P3LRXUrK8/LWEsPr39cH2QH1Rdj69Lx9CgrCdUVJmwcb
Bj8hEiLXL/RYCFNn79A3wNTUvW0rG/AOIf4SLqXtasSRZ0ToaU0ZyDnrNv+0Ol47
rX8tSk+LfXchL9hpIvjCf1vlAYq3pO02favteR/jip3lx/dTjEDE4RJ9qtJzZ4Q=
=fwQY
-----END PGP SIGNATURE-----
Merge tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This pull request has a lot of work done. The main thing is the
changes to the ftrace function callback infrastructure. It's
introducing a way to allow different functions to call directly
different trampolines instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which
always had a different trampoline, but the function tracer trampoline
was called and did basically nothing, and then the function graph
tracer trampoline was called. The difference now, is that the
function graph tracer trampoline can be called directly if a function
is only being traced by the function graph trampoline. If function
tracing is also happening on the same function, the old way is still
done.
The accounting for this takes up more memory when function graph
tracing is activated, as it needs to keep track of which functions it
uses. I have a new way that wont take as much memory, but it's not
ready yet for this merge window, and will have to wait for the next
one.
Another big change was the removal of the ftrace_start/stop() calls
that were used by the suspend/resume code that stopped function
tracing when entering into suspend and resume paths. The stop of
ftrace was done because there was some function that would crash the
system if one called smp_processor_id()! The stop/start was a big
hammer to solve the issue at the time, which was when ftrace was first
introduced into Linux. Now ftrace has better infrastructure to debug
such issues, and I found the problem function and labeled it with
"notrace" and function tracing can now safely be activated all the way
down into the guts of suspend and resume
Other changes include clean ups of uprobe code, clean up of the
trace_seq() code, and other various small fixes and clean ups to
ftrace and tracing"
* tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
ftrace: Add warning if tramp hash does not match nr_trampolines
ftrace: Fix trampoline hash update check on rec->flags
ring-buffer: Use rb_page_size() instead of open coded head_page size
ftrace: Rename ftrace_ops field from trampolines to nr_trampolines
tracing: Convert local function_graph functions to static
ftrace: Do not copy old hash when resetting
tracing: let user specify tracing_thresh after selecting function_graph
ring-buffer: Always run per-cpu ring buffer resize with schedule_work_on()
tracing: Remove function_trace_stop and HAVE_FUNCTION_TRACE_MCOUNT_TEST
s390/ftrace: remove check of obsolete variable function_trace_stop
arm64, ftrace: Remove check of obsolete variable function_trace_stop
Blackfin: ftrace: Remove check of obsolete variable function_trace_stop
metag: ftrace: Remove check of obsolete variable function_trace_stop
microblaze: ftrace: Remove check of obsolete variable function_trace_stop
MIPS: ftrace: Remove check of obsolete variable function_trace_stop
parisc: ftrace: Remove check of obsolete variable function_trace_stop
sh: ftrace: Remove check of obsolete variable function_trace_stop
sparc64,ftrace: Remove check of obsolete variable function_trace_stop
tile: ftrace: Remove check of obsolete variable function_trace_stop
ftrace: x86: Remove check of obsolete variable function_trace_stop
...
After adding all the records to the tramp_hash, add a check that makes
sure that the number of records added matches the number of records
expected to match and do a WARN_ON and disable ftrace if they do
not match.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In the loop of ftrace_save_ops_tramp_hash(), it adds all the recs
to the ops hash if the rec has only one callback attached and the
ops is connected to the rec. It gives a nasty warning and shuts down
ftrace if the rec doesn't have a trampoline set for it. But this
can happen with the following scenario:
# cd /sys/kernel/debug/tracing
# echo schedule do_IRQ > set_ftrace_filter
# mkdir instances/foo
# echo schedule > instances/foo/set_ftrace_filter
# echo function_graph > current_function
# echo function > instances/foo/current_function
# echo nop > instances/foo/current_function
The above would then trigger the following warning and disable
ftrace:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 3145 at kernel/trace/ftrace.c:2212 ftrace_run_update_code+0xe4/0x15b()
Modules linked in: ipt_MASQUERADE sunrpc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ip [...]
CPU: 1 PID: 3145 Comm: bash Not tainted 3.16.0-rc3-test+ #136
Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS SDBLI944.86P 05/08/2007
0000000000000000 ffffffff81808a88 ffffffff81502130 0000000000000000
ffffffff81040ca1 ffff880077c08000 ffffffff810bd286 0000000000000001
ffffffff81a56830 ffff88007a041be0 ffff88007a872d60 00000000000001be
Call Trace:
[<ffffffff81502130>] ? dump_stack+0x4a/0x75
[<ffffffff81040ca1>] ? warn_slowpath_common+0x7e/0x97
[<ffffffff810bd286>] ? ftrace_run_update_code+0xe4/0x15b
[<ffffffff810bd286>] ? ftrace_run_update_code+0xe4/0x15b
[<ffffffff810bda1a>] ? ftrace_shutdown+0x11c/0x16b
[<ffffffff810bda87>] ? unregister_ftrace_function+0x1e/0x38
[<ffffffff810cc7e1>] ? function_trace_reset+0x1a/0x28
[<ffffffff810c924f>] ? tracing_set_tracer+0xc1/0x276
[<ffffffff810c9477>] ? tracing_set_trace_write+0x73/0x91
[<ffffffff81132383>] ? __sb_start_write+0x9a/0xcc
[<ffffffff8120478f>] ? security_file_permission+0x1b/0x31
[<ffffffff81130e49>] ? vfs_write+0xac/0x11c
[<ffffffff8113115d>] ? SyS_write+0x60/0x8e
[<ffffffff81508112>] ? system_call_fastpath+0x16/0x1b
---[ end trace 938c4415cbc7dc96 ]---
------------[ cut here ]------------
Link: http://lkml.kernel.org/r/20140723120805.GB21376@redhat.com
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Having two fields within the same struct that is off by one character
can be confusing and error prone. Rename the counter "trampolines"
to "nr_trampolines" to explicitly show it is a counter and not to
be confused by the "trampoline" field.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Do not waste time copying the old hash if the hash is going to be
reset. Just allocate a new hash and free the old one, as that is
the same result as copying te old one and then resetting it.
Link: http://lkml.kernel.org/p/1405384820-48837-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Wang Nan <wangnan0@huawei.com>
[ SDR: Removed unused ftrace_filter_reset() function ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
All users of function_trace_stop and HAVE_FUNCTION_TRACE_MCOUNT_TEST have
been removed. We can safely remove them from the kernel.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
function_trace_stop is no longer used to stop function tracing.
Remove the check from __ftrace_ops_list_func().
Also, call FTRACE_WARN_ON() instead of setting function_trace_stop
if a ops has no func to call.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When function tracing is being updated function_trace_stop is set to
keep from tracing the updates. This was fine when function tracing
was done from stop machine. But it is no longer done that way and
this can cause real tracing to be missed.
Remove it.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ftrace_stop() is going away as it disables parts of function tracing
that affects users that should not be affected. But ftrace_graph_stop()
is built on ftrace_stop(). Here's another example of killing all of
function tracing because something went wrong with function graph
tracing.
Instead of disabling all users of function tracing on function graph
error, disable only function graph tracing.
A new function is created called ftrace_graph_is_dead(). This is called
in strategic paths to prevent function graph from doing more harm and
allowing at least a warning to be printed before the system crashes.
NOTE: ftrace_stop() is still used until all the archs are converted over
to use ftrace_graph_is_dead(). After that, ftrace_stop() will be removed.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently if an arch supports function graph tracing, the core code will
just assign the function graph trampoline to the function graph addr that
gets called.
But as the old method for function graph tracing always calls the function
trampoline first and that calls the function graph trampoline, some
archs may have the function graph trampoline dependent on operations that
were done in the function trampoline. This causes function graph tracer
to break on those archs.
Instead of having the default be to set the function graph ftrace_ops
to the function graph trampoline, have it instead just set it to zero
which will keep it from jumping to a trampoline that is not set up
to be jumped directly too.
Link: http://lkml.kernel.org/r/53BED155.9040607@nvidia.com
Reported-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Running my ftrace tests on PowerPC, it failed the test that checks
if function_graph tracer is affected by the stack tracer. It was.
Looking into this, I found that the update_function_graph_func()
must be called even if the trampoline function is not changed.
This is because archs like PowerPC do not support ftrace_ops being
passed by assembly and instead uses a helper function (what the
trampoline function points to). Since this function is not changed
even when multiple ftrace_ops are added to the code, the test that
falls out before calling update_function_graph_func() will miss that
the update must still be done.
Call update_function_graph_function() for all calls to
update_ftrace_function()
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When there's no entry in set_ftrace_notrace, it'll print nothing, but
it's better to print something like below like set_graph_notrace does:
#### no functions disabled ####
Link: http://lkml.kernel.org/p/1402644246-4649-1-git-send-email-namhyung@kernel.org
Reported-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When there's no entry in set_graph_notrace, it'll print below message
#### all functions enabled ####
While this is technically correct, it's better to print like below:
#### no functions disabled ####
Link: http://lkml.kernel.org/p/1402590233-22321-3-git-send-email-namhyung@kernel.org
Reported-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The ftrace_graph_notrace option is for specifying notrace filter for
function graph tracer at boot time. It can be altered after boot
using set_graph_notrace file on the debugfs.
Link: http://lkml.kernel.org/p/1402590233-22321-2-git-send-email-namhyung@kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
It seems like it's a leftover from commit 4104d326b6 ("ftrace:
Remove global function list and call function directly"). As it
isn't updated at all, checking its value is meaningless.
Let's get rid of it.
Link: http://lkml.kernel.org/p/1402584972-17824-1-git-send-email-namhyung@kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Simplify ftrace_hash_disable/enable path in ftrace_hash_move
for hardening the process if the memory allocation failed.
Link: http://lkml.kernel.org/p/20140617110442.15167.81076.stgit@kbuild-fedora.novalocal
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The enabled_functions is used to help debug the dynamic function tracing.
Adding what trampolines are attached to files is useful for debugging.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Function graph tracing is a bit different than the function tracers, as
it is processed after either the ftrace_caller or ftrace_regs_caller
and we only have one place to modify the jump to ftrace_graph_caller,
the jump needs to happen after the restore of registeres.
The function graph tracer is dependent on the function tracer, where
even if the function graph tracing is going on by itself, the save and
restore of registers is still done for function tracing regardless of
if function tracing is happening, before it calls the function graph
code.
If there's no function tracing happening, it is possible to just call
the function graph tracer directly, and avoid the wasted effort to save
and restore regs for function tracing.
This requires adding new flags to the dyn_ftrace records:
FTRACE_FL_TRAMP
FTRACE_FL_TRAMP_EN
The first is set if the count for the record is one, and the ftrace_ops
associated to that record has its own trampoline. That way the mcount code
can call that trampoline directly.
In the future, trampolines can be added to arbitrary ftrace_ops, where you
can have two or more ftrace_ops registered to ftrace (like kprobes and perf)
and if they are not tracing the same functions, then instead of doing a
loop to check all registered ftrace_ops against their hashes, just call the
ftrace_ops trampoline directly, which would call the registered ftrace_ops
function directly.
Without this patch perf showed:
0.05% hackbench [kernel.kallsyms] [k] ftrace_caller
0.05% hackbench [kernel.kallsyms] [k] arch_local_irq_save
0.05% hackbench [kernel.kallsyms] [k] native_sched_clock
0.04% hackbench [kernel.kallsyms] [k] __buffer_unlock_commit
0.04% hackbench [kernel.kallsyms] [k] preempt_trace
0.04% hackbench [kernel.kallsyms] [k] prepare_ftrace_return
0.04% hackbench [kernel.kallsyms] [k] __this_cpu_preempt_check
0.04% hackbench [kernel.kallsyms] [k] ftrace_graph_caller
See that the ftrace_caller took up more time than the ftrace_graph_caller
did.
With this patch:
0.05% hackbench [kernel.kallsyms] [k] __buffer_unlock_commit
0.04% hackbench [kernel.kallsyms] [k] call_filter_check_discard
0.04% hackbench [kernel.kallsyms] [k] ftrace_graph_caller
0.04% hackbench [kernel.kallsyms] [k] sched_clock
The ftrace_caller is no where to be found and ftrace_graph_caller still
takes up the same percentage.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The ftrace dynamic record has a flags element that also has a counter.
Instead of hard coding "rec->flags & ~FTRACE_FL_MASK" all over the
place. Use a macro instead.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When registering a function callback for the function tracer, the ops
can specify if it wants to save full regs (like an interrupt would)
for each function that it traces, or if it does not care about regs
and just wants to have the fastest return possible.
Once a ops has registered a function, if other ops register that
function they all will receive the regs too. That's because it does
the work once, it does it for everyone.
Now if the ops wanting regs unregisters the function so that there's
only ops left that do not care about regs, those ops will still
continue getting regs and going through the work for it on that
function. This is because the disabling of the rec counter only
sees the ops registered, and does not see the ops that are still
attached, and does not know if the current ops that are still attached
want regs or not. To play it safe, it just keeps regs being processed
until no function is registered anymore.
Instead of doing that, check the ops that are still registered for that
function and if none want regs for it anymore, then disable the
processing of regs.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
to help out the rest of the kernel to ease their use of trace events.
The big change for this release is the allowing of other tracers,
such as the latency tracers, to be used in the trace instances and allow
for function or function graph tracing to be in the top level
simultaneously.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTlbUqAAoJEKQekfcNnQGuP+8H+wTBG06beHsqe6XcaeXcKNkt
Mimm0O04oQdw89CBWeJvXyOwRTtiN4M/4hxHXBTDtChxM9oUyWw1o0IpSMMuQ16O
w9r3DfC8e1air+ufEuYWM0QNtyzHi8EfDSNia55ON5jvtkCZTXOEKZD+n8M9w28p
I7PVgr0PDztsCpethCpg0M8beK9zuQPWMzsHAQCsKI06Xl5z33kPIJR15Exh+Kr1
uVVTZW7JFVAPuSnteLSIx9pN6OjsVGzOZCljg+O+9/v/02u5nkMiS2nURxae86kg
RTSiRYT6Hvl/MCBhdss/w5kgSk6BYiZ0hXbLtwetvre+vQrOR5CnDw2DxZ7e+gU=
=oudH
-----END PGP SIGNATURE-----
Merge tag 'trace-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Lots of tweaks, small fixes, optimizations, and some helper functions
to help out the rest of the kernel to ease their use of trace events.
The big change for this release is the allowing of other tracers, such
as the latency tracers, to be used in the trace instances and allow
for function or function graph tracing to be in the top level
simultaneously"
* tag 'trace-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (44 commits)
tracing: Fix memory leak on instance deletion
tracing: Fix leak of ring buffer data when new instances creation fails
tracing/kprobes: Avoid self tests if tracing is disabled on boot up
tracing: Return error if ftrace_trace_arrays list is empty
tracing: Only calculate stats of tracepoint benchmarks for 2^32 times
tracing: Convert stddev into u64 in tracepoint benchmark
tracing: Introduce saved_cmdlines_size file
tracing: Add __get_dynamic_array_len() macro for trace events
tracing: Remove unused variable in trace_benchmark
tracing: Eliminate double free on failure of allocation on boot up
ftrace/x86: Call text_ip_addr() instead of the duplicated code
tracing: Print max callstack on stacktrace bug
tracing: Move locking of trace_cmdline_lock into start/stop seq calls
tracing: Try again for saved cmdline if failed due to locking
tracing: Have saved_cmdlines use the seq_read infrastructure
tracing: Add tracepoint benchmark tracepoint
tracing: Print nasty banner when trace_printk() is in use
tracing: Add funcgraph_tail option to print function name after closing braces
tracing: Eliminate duplicate TRACE_GRAPH_PRINT_xx defines
tracing: Add __bitmask() macro to trace events to cpumasks and other bitmasks
...
As the decision to what needs to be done (converting a call to the
ftrace_caller to ftrace_caller_regs or to convert from ftrace_caller_regs
to ftrace_caller) can easily be determined from the rec->flags of
FTRACE_FL_REGS and FTRACE_FL_REGS_EN, there's no need to have the
ftrace_check_record() return either a UPDATE_MODIFY_CALL_REGS or a
UPDATE_MODIFY_CALL. Just he latter is enough. This added flag causes
more complexity than is required. Remove it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
With the moving of the functions that determine what the mcount call site
should be replaced with into the generic code, there is a few places
in the generic code that can use them instead of hard coding it as it
does.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Move and rename get_ftrace_addr() and get_ftrace_addr_old() to
ftrace_get_addr_new() and ftrace_get_addr_curr() respectively.
This moves these two helper functions in the generic code out from
the arch specific code, and renames them to have a better generic
name. This will allow other archs to use them as well as makes it
a bit easier to work on getting separate trampolines for different
functions.
ftrace_get_addr_new() returns the trampoline address that the mcount
call address will be converted to.
ftrace_get_addr_curr() returns the trampoline address of what the
mcount call address currently jumps to.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The ftrace_hash_empty() function is a simple test:
return !hash || !hash->count;
But gcc seems to want to make it a call. As this is in an extreme
hot path of the function tracer, there's no reason it needs to be
a call. I only wrote it to be a helper function anyway, otherwise
it would have been inlined manually.
Force gcc to inline it, as it could have also been a macro.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Back in 2011 Commit ed926f9b35 "ftrace: Use counters to enable
functions to trace" changed the way ftrace accounts for enabled
and disabled traced functions. There was a comment started as:
/*
*
*/
But never finished. Well, that's rather useless. I probably forgot
to save the file before committing it. And it passed review from all
this time.
Anyway, better late than never. I updated the comment to express what
is happening in that somewhat complex code.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit 4104d326b6 "ftrace: Remove global function list and call
function directly" cleaned up the global_ops filtering and made
the code simpler, but it left a variable "hash_enable" that was used
to know if the hash functions should be updated or not. It was
updated if the global_ops did not override them. As the global_ops
are now no different than any other ftrace_ops, the hash always
gets updated and there's no reason to use the hash_enable boolean.
The same goes for hash_disable used in ftrace_shutdown().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Replace uses of &__get_cpu_var for address calculation with this_cpu_ptr.
Link: http://lkml.kernel.org/p/alpine.DEB.2.10.1404291415560.18364@gentwo.org
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit 4104d326b6 "ftrace: Remove global function list and call
function directly" cleaned up the global_ops filtering and made
the code simpler. But it left out function graph filtering which
also depended on that code. The function graph filtering still
needs to use global_ops as the filter otherwise it wont filter
at all.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
A race exists between module loading and enabling of function tracer.
CPU 1 CPU 2
----- -----
load_module()
module->state = MODULE_STATE_COMING
register_ftrace_function()
mutex_lock(&ftrace_lock);
ftrace_startup()
update_ftrace_function();
ftrace_arch_code_modify_prepare()
set_all_module_text_rw();
<enables-ftrace>
ftrace_arch_code_modify_post_process()
set_all_module_text_ro();
[ here all module text is set to RO,
including the module that is
loading!! ]
blocking_notifier_call_chain(MODULE_STATE_COMING);
ftrace_init_module()
[ tries to modify code, but it's RO, and fails!
ftrace_bug() is called]
When this race happens, ftrace_bug() will produces a nasty warning and
all of the function tracing features will be disabled until reboot.
The simple solution is to treate module load the same way the core
kernel is treated at boot. To hardcode the ftrace function modification
of converting calls to mcount into nops. This is done in init/main.c
there's no reason it could not be done in load_module(). This gives
a better control of the changes and doesn't tie the state of the
module to its notifiers as much. Ftrace is special, it needs to be
treated as such.
The reason this would work, is that the ftrace_module_init() would be
called while the module is in MODULE_STATE_UNFORMED, which is ignored
by the set_all_module_text_ro() call.
Link: http://lkml.kernel.org/r/1395637826-3312-1-git-send-email-indou.takao@jp.fujitsu.com
Reported-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The functions ftrace_set_global_filter() and ftrace_set_global_notrace()
still have their old names in the kernel doc (ftrace_set_filter and
ftrace_set_notrace respectively). Replace these with the real names.
Link: http://lkml.kernel.org/p/1398006644-5935-3-git-send-email-wangjiaxing@insigma.com.cn
Signed-off-by: Jiaxing Wang <wangjiaxing@insigma.com.cn>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When using ftrace_ops_list_func, we should skip 4 instead of 3,
to avoid ftrace_call+0x5/0xb appearing in the stack trace:
Depth Size Location (110 entries)
----- ---- --------
0) 2956 0 update_curr+0xe/0x1e0
1) 2956 68 ftrace_call+0x5/0xb
2) 2888 92 enqueue_entity+0x53/0xe80
3) 2796 80 enqueue_task_fair+0x47/0x7e0
4) 2716 28 enqueue_task+0x45/0x70
5) 2688 12 activate_task+0x22/0x30
Add a function using_ftrace_ops_list_func() to test for this while keeping
ftrace_ops_list_func to remain static.
Link: http://lkml.kernel.org/p/1398006644-5935-2-git-send-email-wangjiaxing@insigma.com.cn
Signed-off-by: Jiaxing Wang <wangjiaxing@insigma.com.cn>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Instead of initializing the pm notifier block in register_ftrace_graph(),
initialize it statically. This safes us some code.
Found in the PaX patch, written by the PaX Team.
Link: http://lkml.kernel.org/p/1396186310-3156-1-git-send-email-minipli@googlemail.com
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: PaX Team <pageexec@freemail.hu>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Instead of having a list of global functions that are called,
as only one global function is allow to be enabled at a time, there's
no reason to have a list.
Instead, simply have all the users of the global ops, use the global ops
directly, instead of registering their own ftrace_ops. Just switch what
function is used before enabling the function tracer.
This removes a lot of code as well as the complexity involved with it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt (Red Hat)
Linus Torvalds
Wang Nan
Namhyung Kim
Masami Hiramatsu
Christoph Lameter
Jiaxing Wang
Mathias Krause
Sasha Levin