The wrappers in include/linux/pci-dma-compat.h should go away.
pci_set_dma_mask()/pci_set_consistent_dma_mask() should be
replaced with dma_set_mask()/dma_set_coherent_mask(),
and use dma_set_mask_and_coherent() for both.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/1633663733-47199-6-git-send-email-wangqing@vivo.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Elkhart Lake PSE DMA implementation is integrated with crossbar IP
in order to serve more hardware than there are DMA request lines available.
Due to this, program xBAR hardware to make flexible support of PSE peripheral.
The Device-to-Device has not been tested and it's not supported by DMA Engine,
but it's left in the code for the sake of documenting hardware features.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210712113940.42753-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If PCI enumerated controller has a companion device,
register it in the ACPI DMA controllers as well.
Fixes: f7c799e950 ("dmaengine: dw: we do support Merrifield SoC in PCI mode")
Depends-on: b685fe26e9 ("dmaengine: dw: platform: Split ACPI helpers to separate module")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200526182416.52805-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We are expecting some devices can be enumerated either as PCI or ACPI.
Nevertheless, they will share same information, thus, provide a generic
struct dw_dma_chip_pdata for all glue drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Elkhart Lake Offload Service Engine (OSE) will be called as
Intel(R) Programmable Services Engine (Intel(R) PSE) in documentation.
Update the comment here accordingly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20190813080602.15376-1-jarkko.nikula@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Elkhart Lake OSE (Offload Service Engine) provides few DMA controllers
to the host. Enable them in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the same way as done for ->probe(), call ->remove() based on
the type of the hardware.
While it works now due to equivalency of the two removal functions,
it might be changed in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is a kinda big refactoring that should have been done
in the first place, when Intel iDMA 32-bit support appeared.
It splits operations which are different to Synopsys DesignWare and
Intel iDMA 32-bit controllers.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All known devices, which use DT for configuration, support
memory-to-memory transfers. So enable it by default.
The rest two cases, i.e. Intel Quark and PPC460ex, instantiate DMA driver and
use its channels exclusively for hardware, which means there is no available
channel for any other purposes anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The commit a9ddb575d6
("dmaengine: dw_dmac: Enhance device tree support")
introduces is_private property in uncertain understanding what does it mean.
First of all, documentation defines DMA_PRIVATE capability as
Documentation/crypto/async-tx-api.txt:
The DMA_PRIVATE capability flag is used to tag dma devices that should not be
used by the general-purpose allocator. It can be set at initialization time
if it is known that a channel will always be private. Alternatively,
it is set when dma_request_channel() finds an unused "public" channel.
A couple caveats to note when implementing a driver and consumer:
1/ Once a channel has been privately allocated it will no longer be
considered by the general-purpose allocator even after a call to
dma_release_channel().
2/ Since capabilities are specified at the device level a dma_device with
multiple channels will either have all channels public, or all channels
private.
Documentation/driver-api/dmaengine/provider.rst:
- DMA_PRIVATE
The devices only supports slave transfers, and as such isn't available
for async transfers.
The capability had been introduced by the commit 59b5ec2144
("dmaengine: introduce dma_request_channel and private channels")
and some code didn't changed from that times ever.
Taking into consideration above and the fact that on all known platforms
Synopsys DesignWare DMA engine is attached to serve slave transfers,
the DMA_PRIVATE capability must be enabled for this device unconditionally.
Otherwise, as rightfully noticed in drivers/dma/at_xdmac.c:
/*
* Without DMA_PRIVATE the driver is not able to allocate more than
* one channel, second allocation fails in private_candidate.
*/
because of of a caveats mentioned in above documentation excerpts.
So, remove conditional around DMA_PRIVATE followed by removal leftovers.
If someone wonders, DMA_PRIVATE can be not used if and only if the all channels
of the DMA controller are supposed to serve memory-to-memory like operations.
For example, EP93xx has two controllers, one of which can only perform
memory-to-memory transfers
Note, this change doesn't affect dmatest to be able to test such controllers.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (maintainer:SERIAL DRIVERS)
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Merrifield platform contains Intel integrated DMA (iDMA 32-bit) which has
a slightly different register mapping, e.g. some bits in CTL_* and CFG_*
channel registers, and has to use platform data since there is no
autoconfiguration.
The iDMA 32-bit specification is available in the publicly available
documentation for Intel Braswell and BayTrail SoCs as LPE Audio DMA.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is really useful not only for debugging to have an IRQ line and DMA
pool labeled with driver and its instance ID. Do this for DesignWare DMA
driver.
All current users of this IP would be enhanced later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
LPE Audio driver should take care of DMA IPs by itself. Keeping an ID like this
in dw_dma_pci.c is anyway wrong since that block has two DMA controllers under
one ID (like MFD device).
That's also why I didn't include LPE Audio ID for Intel Merrifield previously.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
WildcatPoint PCH as seen on MacBook 12-inch (Early 2015) has PCI enabled
DesignWare DMA controller. Enable it by adding its ID to the corresponding
driver.
Reported-by: Leif Liddy <leif.liddy@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=110901
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of hardconding a platform data for dw_dmac let's use it's own
autoconfiguration feature. Thus, remove hardcoded values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of conditional exporing of dw_dma_suspend() / dw_dma_resume() let's
export dw_dma_disable() / dw_dma_enable(). Since dw_dma_shutdown() repeats
dw_dma_disable() we may safely remove it at all.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Braswell SoC has two DMA controllers for LPSS. This patch adds them to
supported list in the PCI driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is deprecated.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 4501fe61 "dma: dw: Add suspend and resume handling for PCI mode
DW_DMAC." introduces system power management callbacks. Regarding to commit
f78c4cff "PM / Sleep: Add macro to define common late/early system PM
callbacks" we have nice macro to setup dev_pm_ops structure. This patch
converts a driver to use the macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is to disable/enable DW_DMAC hw during late suspend/early resume.
Since DMA is providing service to other clients (eg: SPI, HSUART),
we need to ensure DMA suspends after the clients and resume
before the clients are active.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case of PCI mode the DMA controller has a specific ID. Put this ID to the
list of supported.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is the PCI part of the DesignWare DMAC driver. The controller is usually
used in the Intel hardware such as Intel Medfield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Qing Wang
Andy Shevchenko
Jarkko Nikula
Jingoo Han
Chew, Chiau Ee