s5pv210 and exynos4 are now DT only platforms hence these
entries can now be safely removed from the match table.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The s3c64xx platform data already contains a pointer to the
DMA filter function, but not to the associated data.
This simplifies the code and makes it more generic by
passing the data along with the filter function like
we do for other drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify s3c64xx_spi_remove by replacing the clock disabling with calling
runtime PM suspend which does the same.
Waking up the device if it was suspended wouldn't be strictly needed
for this driver but using pm_runtime_get_sync is cleaner and makes
s3c64xx_spi_remove more consistent with the runtime PM handling in
s3c64xx_spi_setup.
pm_runtime_force_suspend does most of the work for us:
disabling the clocks, disabling runtime PM and setting it to
"suspended" state.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The runtime PM suspend / resume handlers take care of the enabling/
disabling the clocks already. Therefore replace the duplicated
clock handling with pm_runtime_force_suspend/resume.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the driver to make full use of runtime PM autosuspend.
Before only the SPI core was instructed to use autosuspend
by setting master->auto_runtime_pm. Nevertheless due to the missing
pm_runtime_use_autosuspend call autosuspend wasn't active.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Printing the FIFO depth does not add much noise in the log and can be useful
for debugging transfer issues.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Exynos 7 arm64 support now allows the S3C64xx SPI driver to be
compiled into an ARM64 kernel, so the cast from the [rt]x_dmach int
variable to a void* in this driver now triggers a warning.
Add a long cast to silence the compiler.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/spi/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
The device already asks the core to hold a runtime PM reference while it
is active so it is redundant to open code that in the driver itself.
Signed-off-by: Mark Brown <broonie@kernel.org>
Exynos7 SPI controller supports only the auto Selection of
CS toggle mode and Exynos7 SoC includes six SPI controllers.
Add support for these changes in Exynos7 SPI controller driver.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
The s3c64xx SPI driver uses a custom DT binding to specify
the GPIO used to drive the chip select (CS) line instead of
using the generic "cs-gpios" property already defined in:
Documentation/devicetree/bindings/spi/spi-bus.txt.
It's unfortunate that drivers are not using standard bindings
and creating custom ones instead but in most cases this can't
be changed without breaking Device Tree backward compatibility.
But in the case of this driver, its DT binding has been broken
for more than a year. Since after commit (dated June, 21 2013):
3146bee ("spi: s3c64xx: Added provision for dedicated cs pin")
DT backward compatibility was broken and nobody noticed until
now when the commit was reverted. So it seems to be safe to
change the binding to use the standard SPI "cs-gpios" property
instead of using a custom one just for this driver.
This patch also allows boards that don't use a GPIO pin for the
CS to work with the driver since the SPI core will take care of
setting spi->cs_gpio to -ENOENT if a board wants to use the built
in CS instead of a GPIO as explained in the SPI bus DT binding:
Documentation/devicetree/bindings/spi/spi-bus.txt.
For non-DT platforms, spi->cs_gpio will be set to -ENOENT as well
unless they specify a GPIO pin in their platform data. So both
native and GPIO chip select is also supported for legacy boards.
The above use case was what motivated commit 3146bee which broke
the DT binding backward compatibility in the first place.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
[javier.martinez@collabora.co.uk: split changes and improve commit message]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit 3146beec21.
This commit resulted in a DT backward compatibility breakage.
Some devices use the native chip select (CS) instead of a GPIO
pin to drive the CS line. But the SPI driver made it mandatory
to specify a GPIO pin in the SPI device node controller-data.
So, using the built-in CS was not possible with the driver.
Commit 3146bee tried to fix that by adding a "cs-gpio" property
which could be defined in the SPI device node to make the driver
request the GPIO from the controller-data node.
Unfortunately that changed the old DT binding semantics since
now it's mandatory to have the "cs-gpio" property defined in
the SPI device node in order to use a GPIO pin to drive the CS.
As an example, a SPI device was defined before the commit with:
spi@12d20000 {
slave-node@0 {
controller-data {
cs-gpio = <&gpb1 2 0>;
}
}
}
and after the commit, the following DTS snippet must be used:
spi@12d20000 {
cs-gpio;
slave-node@0 {
controller-data {
cs-gpio = <&gpb1 2 0>;
}
}
}
So, after commit 3146bee the driver does not look for the GPIO
by default and it only looks for it if the top level "cs-gpio"
property is defined while the default used to be the opposite.
To always request the GPIO defined in the controller-data node.
This means that old FDT that of course didn't have this added
"cs-gpio" DT property in the SPI node broke after this change.
The offending commit can't be reverted cleanly since more than
a year have passed and other changes were made in the meantime
but this patch partially reverts the driver to it's original
state so old FDT can work again.
This patch will break Device Trees that were relying on the new
behavior of course but the patch should be reverted because:
a) There aren't DTS in mainline that use this new property.
b) They were relying on a behavior that broke DT compatibility.
c) The new binding is awkard, needing two properties with the
same name (cs-gpio) on different nodes is confusing at least.
d) The new property was not added to the DT binding doc:
Documentation/devicetree/bindings/spi/spi-samsung.txt
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes sp5c100 related spi because of no more support
s5pc100 SoC.
Cc: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes s5p64x0 related spi because of no more support for
s5p64x0 SoCs. Meanwhile, cleanup SPI DT bindings for s5p6440-spi, it
should be s5p64x0-spi instead.
Cc: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove functions that only had an effect when using S3C_DMA and inline
dmaengine_terminate_all() since it's pointless to have a function which
expands to a single function call.
Signed-off-by: Mark Brown <broonie@linaro.org>
All the platforms which use the old S3C_DMA API have now been converted to
dmaengine so we can remove the legacy code from the driver, simplifying
maintenance.
Signed-off-by: Mark Brown <broonie@linaro.org>
When using dmaengine allow the core to do the DMA mapping. We still need
local mapping code for the non-dmaengine case so this doesn't save us
anything for now.
Signed-off-by: Mark Brown <broonie@linaro.org>
We cannot unconditionally use dma_map_single() to map data for use with
SPI since transfers may exceed a page and virtual addresses may not be
provided with physically contiguous pages. Further, addresses allocated
using vmalloc() need to be mapped differently to other addresses.
Currently only the MXS driver handles all this, a few drivers do handle
the possibility that buffers may not be physically contiguous which is
the main potential problem but many don't even do that. Factoring this
out into the core will make it easier for drivers to do a good job so if
the driver is using the core DMA code then generate a scatterlist
instead of mapping to a single address so do that.
This code is mainly based on a combination of the existing code in the MXS
and PXA2xx drivers. In future we should be able to extend it to allow the
core to concatenate adjacent transfers if they are compatible, improving
performance.
Currently for simplicity clients are not allowed to use the scatterlist
when they do DMA mapping, in the future the existing single address
mappings will be replaced with use of the scatterlist most likely as
part of pre-verifying transfers.
This change makes it mandatory to use scatterlists when using the core DMA
mapping so update the s3c64xx driver to do this when used with dmaengine.
Doing so makes the code more ugly but it is expected that the old s3c-dma
code can be removed very soon.
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no meaningful code sharing between the PIO and DMA variants
(just the timeout calculation) so in order to make the code easier to
work with split the two cases.
Looking at the code it is not clear how the PIO version works for large
transmits, greater than FIFO size is only handled for RX.
Signed-off-by: Mark Brown <broonie@linaro.org>
The GPIO enable and disable is done in the core so does not need to be
replicated in the driver, delete the unneeded code. enable_cs() was not
referenced at all.
Signed-off-by: Mark Brown <broonie@linaro.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix doubled clock disable and unprepare during PM suspend which triggered
the warnings:
WARNING: at drivers/clk/clk.c:800 clk_disable+0x18/0x24()
Modules linked in:
CPU: 0 PID: 1745 Comm: sh Not tainted 3.10.14-01211-ge2549bb-dirty #62
[<c0015980>] (unwind_backtrace+0x0/0x138) from [<c0012a44>] (show_stack+0x10/0x14)
[<c0012a44>] (show_stack+0x10/0x14) from [<c0022818>] (warn_slowpath_common+0x4c/0x68)
[<c0022818>] (warn_slowpath_common+0x4c/0x68) from [<c0022850>] (warn_slowpath_null+0x1c/0x24)
[<c0022850>] (warn_slowpath_null+0x1c/0x24) from [<c036e274>] (clk_disable+0x18/0x24)
[<c036e274>] (clk_disable+0x18/0x24) from [<c02d5f78>] (s3c64xx_spi_suspend+0x28/0x54)
[<c02d5f78>] (s3c64xx_spi_suspend+0x28/0x54) from [<c02b3a54>] (platform_pm_suspend+0x2c/0x5c)
[<c02b3a54>] (platform_pm_suspend+0x2c/0x5c) from [<c02b8a30>] (dpm_run_callback+0x44/0x7c)
[<c02b8a30>] (dpm_run_callback+0x44/0x7c) from [<c02b8b70>] (__device_suspend+0x108/0x300)
[<c02b8b70>] (__device_suspend+0x108/0x300) from [<c02ba4e0>] (dpm_suspend+0x54/0x208)
[<c02ba4e0>] (dpm_suspend+0x54/0x208) from [<c0066bcc>] (suspend_devices_and_enter+0x98/0x458)
[<c0066bcc>] (suspend_devices_and_enter+0x98/0x458) from [<c0067150>] (pm_suspend+0x1c4/0x25c)
[<c0067150>] (pm_suspend+0x1c4/0x25c) from [<c0066044>] (state_store+0x6c/0xbc)
[<c0066044>] (state_store+0x6c/0xbc) from [<c0203290>] (kobj_attr_store+0x14/0x20)
[<c0203290>] (kobj_attr_store+0x14/0x20) from [<c0157530>] (sysfs_write_file+0xfc/0x164)
[<c0157530>] (sysfs_write_file+0xfc/0x164) from [<c00fd6b0>] (vfs_write+0xbc/0x1bc)
[<c00fd6b0>] (vfs_write+0xbc/0x1bc) from [<c00fdaf0>] (SyS_write+0x40/0x68)
[<c00fdaf0>] (SyS_write+0x40/0x68) from [<c000ea80>] (ret_fast_syscall+0x0/0x3c)
The clocks may be already disabled before suspending. Check PM runtime
suspend status and disable clocks only if device is not suspended.
During resume do not enable the clocks if device is runtime suspended.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
During PM resume and suspend do not ignore the return value of
spi_master_suspend() or spi_master_resume(). Instead pass it further.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
pm_runtime_put() wasn't called if clock rate could not be set up in
s3c64xx_spi_setup() leading to invalid count of device pm_runtime usage.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark device as PM runtime active during initialization to reflect
actual device power/clocks state. This reduces the enable count for SPI
bus controller gate clock so it can be disabled when the bus controller
is not used.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is of very little value in itself but will be useful once the loop
iterating over the transfers is also factored out into the core.
Signed-off-by: Mark Brown <broonie@linaro.org>
The hardware level /CS handling is tied to the start of the data path so
is rolled into the same function as we use to manipulate GPIO /CS. In
order to support factoring out the /CS handling into the core separate the
two and explicitly start transfers separately to the /CS handling.
Signed-off-by: Mark Brown <broonie@linaro.org>
To help with bisection of future refactoring to share more of the code for
handling a spi_message pull the enabling of GPIO based /CS prior to all
the hardware setup for starting a transfer.
Signed-off-by: Mark Brown <broonie@linaro.org>
The hardware level /CS handling is tied to the start of the data path so
is rolled into the same function as we use to manipulate GPIO /CS. In
order to support factoring out the /CS handling into the core separate the
two and explicitly start transfers separately to the /CS handling.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than using the driver custom platform data to store the chip select
GPIO use the cs_gpio field provided by the SPI core, supporting future
refectoring.
Signed-off-by: Mark Brown <broonie@linaro.org>
Sylwester Nawrocki
Arnd Bergmann
Jarkko Nikula
Heiner Kallweit
Michal Suchanek
Krzysztof Kozlowski
Andre Przywara
Linus Torvalds
Rafael J. Wysocki
Mark Brown
Padmavathi Venna
Wolfram Sang
Naveen Krishna Chatradhi
Javier Martinez Canillas
Kukjin Kim
Mark Brown
Jingoo Han
Axel Lin
Geert Uytterhoeven
Krzysztof Kozlowski