Newer ISA versions are enabled by clearing all bits in the PCR
associated with previous versions of the ISA. Enable ISA v3.1 support
by updating the PCR mask to include ISA v3.0. This ensures all PCR
bits corresponding to earlier architecture versions get cleared
thereby enabling ISA v3.1 if supported by the hardware.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200521014341.29095-3-alistair@popple.id.au
There is a potential race condition between hypervisor page faults
and flushing a memslot. It is possible for a page fault to read the
memslot before a memslot is updated and then write a PTE to the
partition-scoped page tables after kvmppc_radix_flush_memslot has
completed. (Note that this race has never been explicitly observed.)
To close this race, it is sufficient to increment the MMU sequence
number while the kvm->mmu_lock is held. That will cause
mmu_notifier_retry() to return true, and the page fault will then
return to the guest without inserting a PTE.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Although in general we do not expect valid PTEs to be found in
kvmppc_create_pte when we are inserting a large page mapping, there
is one situation where this can occur. That is when dirty page
logging is turned off for a memslot while the VM is running.
Because the new memslots are installed before the old memslot is
flushed in kvmppc_core_commit_memory_region_hv(), there is a
window where a hypervisor page fault can try to install a 2MB
(or 1GB) page where there are already small page mappings which
were installed while dirty page logging was enabled and which
have not yet been flushed.
Since we have a situation where valid PTEs can legitimately be
found by kvmppc_unmap_free_pte, and which can be triggered by
userspace, just remove the WARN_ON_ONCE, since it is undesirable
to have userspace able to trigger a kernel warning.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The commit 8c47b6ff29 ("KVM: PPC: Book3S HV: Check caller of H_SVM_*
Hcalls") added checks of secure bit of SRR1 to filter out the Hcall
reserved to the Ultravisor.
However, the Hcall H_SVM_INIT_ABORT is made by the Ultravisor passing the
context of the VM calling UV_ESM. This allows the Hypervisor to return to
the guest without going through the Ultravisor. Thus the Secure bit of SRR1
is not set in that particular case.
In the case a regular VM is calling H_SVM_INIT_ABORT, this hcall will be
filtered out in kvmppc_h_svm_init_abort() because kvm->arch.secure_guest is
not set in that case.
Fixes: 8c47b6ff29 ("KVM: PPC: Book3S HV: Check caller of H_SVM_* Hcalls")
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
It is unsafe to traverse kvm->arch.spapr_tce_tables and
stt->iommu_tables without the RCU read lock held. Also, add
cond_resched_rcu() in places with the RCU read lock held that could take
a while to finish.
arch/powerpc/kvm/book3s_64_vio.c:76 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by qemu-kvm/4265.
stack backtrace:
CPU: 96 PID: 4265 Comm: qemu-kvm Not tainted 5.7.0-rc4-next-20200508+ #2
Call Trace:
[c000201a8690f720] [c000000000715948] dump_stack+0xfc/0x174 (unreliable)
[c000201a8690f770] [c0000000001d9470] lockdep_rcu_suspicious+0x140/0x164
[c000201a8690f7f0] [c008000010b9fb48] kvm_spapr_tce_release_iommu_group+0x1f0/0x220 [kvm]
[c000201a8690f870] [c008000010b8462c] kvm_spapr_tce_release_vfio_group+0x54/0xb0 [kvm]
[c000201a8690f8a0] [c008000010b84710] kvm_vfio_destroy+0x88/0x140 [kvm]
[c000201a8690f8f0] [c008000010b7d488] kvm_put_kvm+0x370/0x600 [kvm]
[c000201a8690f990] [c008000010b7e3c0] kvm_vm_release+0x38/0x60 [kvm]
[c000201a8690f9c0] [c0000000005223f4] __fput+0x124/0x330
[c000201a8690fa20] [c000000000151cd8] task_work_run+0xb8/0x130
[c000201a8690fa70] [c0000000001197e8] do_exit+0x4e8/0xfa0
[c000201a8690fb70] [c00000000011a374] do_group_exit+0x64/0xd0
[c000201a8690fbb0] [c000000000132c90] get_signal+0x1f0/0x1200
[c000201a8690fcc0] [c000000000020690] do_notify_resume+0x130/0x3c0
[c000201a8690fda0] [c000000000038d64] syscall_exit_prepare+0x1a4/0x280
[c000201a8690fe20] [c00000000000c8f8] system_call_common+0xf8/0x278
====
arch/powerpc/kvm/book3s_64_vio.c:368 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by qemu-kvm/4264:
#0: c000201ae2d000d8 (&vcpu->mutex){+.+.}-{3:3}, at: kvm_vcpu_ioctl+0xdc/0x950 [kvm]
#1: c000200c9ed0c468 (&kvm->srcu){....}-{0:0}, at: kvmppc_h_put_tce+0x88/0x340 [kvm]
====
arch/powerpc/kvm/book3s_64_vio.c:108 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by qemu-kvm/4257:
#0: c000200b1b363a40 (&kv->lock){+.+.}-{3:3}, at: kvm_vfio_set_attr+0x598/0x6c0 [kvm]
====
arch/powerpc/kvm/book3s_64_vio.c:146 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by qemu-kvm/4257:
#0: c000200b1b363a40 (&kv->lock){+.+.}-{3:3}, at: kvm_vfio_set_attr+0x598/0x6c0 [kvm]
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In the current kvm version, 'kvm_run' has been included in the 'kvm_vcpu'
structure. For historical reasons, many kvm-related function parameters
retain the 'kvm_run' and 'kvm_vcpu' parameters at the same time. This
patch does a unified cleanup of these remaining redundant parameters.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The 'kvm_run' field already exists in the 'vcpu' structure, which
is the same structure as the 'kvm_run' in the 'vcpu_arch' and
should be deleted.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The newly introduced ibm,secure-memory nodes supersede the
ibm,uv-firmware's property secure-memory-ranges.
Firmware will no more expose the secure-memory-ranges property so first
read the new one and if not found rollback to the older one.
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Free function kfree() already does NULL check, so the additional
check is unnecessary, just remove it.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Merge our topic branch shared with the kvm-ppc tree.
This brings in one commit that touches the XIVE interrupt controller
logic across core and KVM code.
Power10 is introducing second DAWR. Use real register names from ISA
for current macros:
s/SPRN_DAWR/SPRN_DAWR0/
s/SPRN_DAWRX/SPRN_DAWRX0/
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-2-ravi.bangoria@linux.ibm.com
Add the BOUNDARY SRR1 bit definition for when the cause of an
alignment exception is a prefixed instruction that crosses a 64-byte
boundary. Add the PREFIXED SRR1 bit definition for exceptions caused
by prefixed instructions.
Bit 35 of SRR1 is called SRR1_ISI_N_OR_G. This name comes from it
being used to indicate that an ISI was due to the access being no-exec
or guarded. ISA v3.1 adds another purpose. It is also set if there is
an access in a cache-inhibited location for prefixed instruction.
Rename from SRR1_ISI_N_OR_G to SRR1_ISI_N_G_OR_CIP.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-23-jniethe5@gmail.com
In preparation for instructions having a more complex data type start
using a macro, ppc_inst(), for making an instruction out of a u32. A
macro is used so that instructions can be used as initializer elements.
Currently this does nothing, but it will allow for creating a data type
that can represent prefixed instructions.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Change include guard to _ASM_POWERPC_INST_H]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-7-jniethe5@gmail.com
Two new stats for exposing halt-polling cpu usage:
halt_poll_success_ns
halt_poll_fail_ns
Thus sum of these 2 stats is the total cpu time spent polling. "success"
means the VCPU polled until a virtual interrupt was delivered. "fail"
means the VCPU had to schedule out (either because the maximum poll time
was reached or it needed to yield the CPU).
To avoid touching every arch's kvm_vcpu_stat struct, only update and
export halt-polling cpu usage stats if we're on x86.
Exporting cpu usage as a u64 and in nanoseconds means we will overflow at
~500 years, which seems reasonably large.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Jon Cargille <jcargill@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20200508182240.68440-1-jcargill@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The use of any sort of waitqueue (simple or regular) for
wait/waking vcpus has always been an overkill and semantically
wrong. Because this is per-vcpu (which is blocked) there is
only ever a single waiting vcpu, thus no need for any sort of
queue.
As such, make use of the rcuwait primitive, with the following
considerations:
- rcuwait already provides the proper barriers that serialize
concurrent waiter and waker.
- Task wakeup is done in rcu read critical region, with a
stable task pointer.
- Because there is no concurrency among waiters, we need
not worry about rcuwait_wait_event() calls corrupting
the wait->task. As a consequence, this saves the locking
done in swait when modifying the queue. This also applies
to per-vcore wait for powerpc kvm-hv.
The x86 tscdeadline_latency test mentioned in 8577370fb0
("KVM: Use simple waitqueue for vcpu->wq") shows that, on avg,
latency is reduced by around 15-20% with this change.
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: kvmarm@lists.cs.columbia.edu
Cc: linux-mips@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Message-Id: <20200424054837.5138-6-dave@stgolabs.net>
[Avoid extra logic changes. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When an interrupt has been handled, the OS notifies the interrupt
controller with a EOI sequence. On a POWER9 system using the XIVE
interrupt controller, this can be done with a load or a store
operation on the ESB interrupt management page of the interrupt. The
StoreEOI operation has less latency and improves interrupt handling
performance but it was deactivated during the POWER9 DD2.0 timeframe
because of ordering issues. We use the LoadEOI today but we plan to
reactivate StoreEOI in future architectures.
There is usually no need to enforce ordering between ESB load and
store operations as they should lead to the same result. E.g. a store
trigger and a load EOI can be executed in any order. Assuming the
interrupt state is PQ=10, a store trigger followed by a load EOI will
return a Q bit. In the reverse order, it will create a new interrupt
trigger from HW. In both cases, the handler processing interrupts is
notified.
In some cases, the XIVE_ESB_SET_PQ_10 load operation is used to
disable temporarily the interrupt source (mask/unmask). When the
source is reenabled, the OS can detect if interrupts were received
while the source was disabled and reinject them. This process needs
special care when StoreEOI is activated. The ESB load and store
operations should be correctly ordered because a XIVE_ESB_STORE_EOI
operation could leave the source enabled if it has not completed
before the loads.
For those cases, we enforce Load-after-Store ordering with a special
load operation offset. To avoid performance impact, this ordering is
only enforced when really needed, that is when interrupt sources are
temporarily disabled with the XIVE_ESB_SET_PQ_10 load. It should not
be needed for other loads.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220081506.31209-1-clg@kaod.org
KVM_CAP_SET_GUEST_DEBUG should be supported for x86 however it's not declared
as supported. My wild guess is that userspaces like QEMU are using "#ifdef
KVM_CAP_SET_GUEST_DEBUG" to check for the capability instead, but that could be
wrong because the compilation host may not be the runtime host.
The userspace might still want to keep the old "#ifdef" though to not break the
guest debug on old kernels.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20200505154750.126300-1-peterx@redhat.com>
[Do the same for PPC and s390. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Current code just hold rmap lock to ensure parallel page table update is
prevented. That is not sufficient. The kernel should also check whether
a mmu_notifer callback was running in parallel.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200505071729.54912-16-aneesh.kumar@linux.ibm.com
Since kvmppc_do_h_enter can get called in realmode use low level
arch_spin_lock which is safe to be called in realmode.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200505071729.54912-15-aneesh.kumar@linux.ibm.com
The locking rules for walking nested shadow linux page table is different from process
scoped table. Hence add a helper for nested page table walk and also
add check whether we are holding the right locks.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200505071729.54912-11-aneesh.kumar@linux.ibm.com
The locking rules for walking partition scoped table is different from process
scoped table. Hence add a helper for secondary linux page table walk and also
add check whether we are holding the right locks.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200505071729.54912-10-aneesh.kumar@linux.ibm.com
These functions can get called in realmode. Hence use low level
arch_spin_lock which is safe to be called in realmode.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200505071729.54912-9-aneesh.kumar@linux.ibm.com
- Fix a regression introduced in the last merge window, which results
in guests in HPT mode dying randomly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJeni/pAAoJEJ2a6ncsY3GfTRoIANAQjIZi96AfJcfnrYQ4yUF7
scxawTiJ9VavvsEJLJ7vsozrJ4xxmvmA0fFWC84uw9+BwPqoLFFvZTjazbGEDVvF
FGwNBR/k7nfFVMIHS3K9iy9KjvYL3xkL26AgFTDJFq8hmOO9pH0txuk4r7SXb+NX
bGG0mScAD/Dg/HwAHAS6EP3jT35QtGTK62p8foqVTziTNcmBn9Ywtg0lEzAcq2iY
Y1BUD4Ov3cggshMI9SqHE8Yyq0XA2Wi6ggcyz/gVzvcbdFQmtg57Tri8nN8661LX
XKh+VTpYSIxNs5GgjwlNesJzJ9h6CSynJF556qrjQ0XsXcNqvn8fcZdNQ+hnRYw=
=Y19W
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-5.7-1' into topic/ppc-kvm
This brings in a fix from the kvm-ppc tree that was merged to mainline
after rc2, and so isn't in the base of our topic branch. We'd like it
in the topic branch because it interacts with patches we plan to carry
in this branch.
- Fix a regression introduced in the last merge window, which results
in guests in HPT mode dying randomly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJeni/pAAoJEJ2a6ncsY3GfTRoIANAQjIZi96AfJcfnrYQ4yUF7
scxawTiJ9VavvsEJLJ7vsozrJ4xxmvmA0fFWC84uw9+BwPqoLFFvZTjazbGEDVvF
FGwNBR/k7nfFVMIHS3K9iy9KjvYL3xkL26AgFTDJFq8hmOO9pH0txuk4r7SXb+NX
bGG0mScAD/Dg/HwAHAS6EP3jT35QtGTK62p8foqVTziTNcmBn9Ywtg0lEzAcq2iY
Y1BUD4Ov3cggshMI9SqHE8Yyq0XA2Wi6ggcyz/gVzvcbdFQmtg57Tri8nN8661LX
XKh+VTpYSIxNs5GgjwlNesJzJ9h6CSynJF556qrjQ0XsXcNqvn8fcZdNQ+hnRYw=
=Y19W
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
PPC KVM fix for 5.7
- Fix a regression introduced in the last merge window, which results
in guests in HPT mode dying randomly.
In earlier versions of kvm, 'kvm_run' was an independent structure
and was not included in the vcpu structure. At present, 'kvm_run'
is already included in the vcpu structure, so the parameter
'kvm_run' is redundant.
This patch simplifies the function definition, removes the extra
'kvm_run' parameter, and extracts it from the 'kvm_vcpu' structure
if necessary.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Message-Id: <20200416051057.26526-1-tianjia.zhang@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The macros VM_STAT and VCPU_STAT are redundantly implemented in multiple
files, each used by a different architecure to initialize the debugfs
entries for statistics. Since they all have the same purpose, they can be
unified in a single common definition in include/linux/kvm_host.h
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20200414155625.20559-1-eesposit@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since cd758a9b57 "KVM: PPC: Book3S HV: Use __gfn_to_pfn_memslot in HPT
page fault handler", it's been possible in fairly rare circumstances to
load a non-present PTE in kvmppc_book3s_hv_page_fault() when running a
guest on a POWER8 host.
Because that case wasn't checked for, we could misinterpret the non-present
PTE as being a cache-inhibited PTE. That could mismatch with the
corresponding hash PTE, which would cause the function to fail with -EFAULT
a little further down. That would propagate up to the KVM_RUN ioctl()
generally causing the KVM userspace (usually qemu) to fall over.
This addresses the problem by catching that case and returning to the guest
instead.
For completeness, this fixes the radix page fault handler in the same
way. For radix this didn't cause any obvious misbehaviour, because we
ended up putting the non-present PTE into the guest's partition-scoped
page tables, leading immediately to another hypervisor data/instruction
storage interrupt, which would go through the page fault path again
and fix things up.
Fixes: cd758a9b57 "KVM: PPC: Book3S HV: Use __gfn_to_pfn_memslot in HPT page fault handler"
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1820402
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Some bug fixes.
The new vdpa subsystem with two first drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl6MS7wPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpGp8H/2H49Gya1cfVbGU13qgmBSQqQXC8hS3iNLuG
ltRgU+jafJT//kvkdm3/DUzfK3eRUWUfqZLKEbAQDtMY0OGHi/KGEBYVLDde7Zxt
Lg4VnwBhkYDR/f01ZZDbHxzj9JAr83i28nILjLIqf3a1BX4zf203+ZE0/JM8a7wL
dOPoH7NAfyz5ul2F67bR1IOF8vC6TidpavzR2+HC/MocHYXb6Bgfvt+i4EcrfuMf
9lnBfajgklKr9sNJniwvvR1pWVg+YyG3VeC6T8tIC/xzbCmIoNT+5b3q2XPSIHq1
EuQTeXH9CBFXS0qcFlq2ktR1xd1Lx95hKwZpqLwLFDmfgjhV2QU=
=/84P
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- Some bug fixes
- The new vdpa subsystem with two first drivers
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-balloon: Revert "virtio-balloon: Switch back to OOM handler for VIRTIO_BALLOON_F_DEFLATE_ON_OOM"
vdpa: move to drivers/vdpa
virtio: Intel IFC VF driver for VDPA
vdpasim: vDPA device simulator
vhost: introduce vDPA-based backend
virtio: introduce a vDPA based transport
vDPA: introduce vDPA bus
vringh: IOTLB support
vhost: factor out IOTLB
vhost: allow per device message handler
vhost: refine vhost and vringh kconfig
virtio-balloon: Switch back to OOM handler for VIRTIO_BALLOON_F_DEFLATE_ON_OOM
virtio-net: Introduce hash report feature
virtio-net: Introduce RSS receive steering feature
virtio-net: Introduce extended RSC feature
tools/virtio: option to build an out of tree module
- A large series from Nick for 64-bit to further rework our exception vectors,
and rewrite portions of the syscall entry/exit and interrupt return in C. The
result is much easier to follow code that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had become badly
intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings from the
workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and update the
status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to:
Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen Zhou, Christophe JAILLET,
Christophe Leroy, Christoph Hellwig, Clement Courbet, Daniel Axtens, David
Gibson, Douglas Miller, Fabiano Rosas, Fangrui Song, Ganesh Goudar, Gautham R.
Shenoy, Greg Kroah-Hartman, Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie
Halip, Jan Kara, Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger,
Laurentiu Tudor, Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh
Salgaonkar, Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira,
Michael Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat, Rasmus Villemoes, Ravi
Bangoria, Roman Bolshakov, Sam Bobroff, Sandipan Das, Santosh S, Sedat Dilek,
Segher Boessenkool, Shilpasri G Bhat, Sourabh Jain, Srikar Dronamraju, Stephen
Rothwell, Tyrel Datwyler, Vaibhav Jain, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=ARdm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Slightly late as I had to rebase mid-week to insert a bug fix:
- A large series from Nick for 64-bit to further rework our exception
vectors, and rewrite portions of the syscall entry/exit and
interrupt return in C. The result is much easier to follow code
that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had
become badly intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings
from the workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and
update the status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to: Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew
Donnellan, Aneesh Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen
Zhou, Christophe JAILLET, Christophe Leroy, Christoph Hellwig, Clement
Courbet, Daniel Axtens, David Gibson, Douglas Miller, Fabiano Rosas,
Fangrui Song, Ganesh Goudar, Gautham R. Shenoy, Greg Kroah-Hartman,
Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie Halip, Jan Kara,
Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger, Laurentiu Tudor,
Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh Salgaonkar,
Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira, Michael
Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat,
Rasmus Villemoes, Ravi Bangoria, Roman Bolshakov, Sam Bobroff,
Sandipan Das, Santosh S, Sedat Dilek, Segher Boessenkool, Shilpasri G
Bhat, Sourabh Jain, Srikar Dronamraju, Stephen Rothwell, Tyrel
Datwyler, Vaibhav Jain, YueHaibing"
* tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (158 commits)
powerpc: Make setjmp/longjmp signature standard
powerpc/cputable: Remove unnecessary copy of cpu_spec->oprofile_type
powerpc: Suppress .eh_frame generation
powerpc: Drop -fno-dwarf2-cfi-asm
powerpc/32: drop unused ISA_DMA_THRESHOLD
powerpc/powernv: Add documentation for the opal sensor_groups sysfs interfaces
selftests/powerpc: Fix try-run when source tree is not writable
powerpc/vmlinux.lds: Explicitly retain .gnu.hash
powerpc/ptrace: move ptrace_triggered() into hw_breakpoint.c
powerpc/ptrace: create ppc_gethwdinfo()
powerpc/ptrace: create ptrace_get_debugreg()
powerpc/ptrace: split out ADV_DEBUG_REGS related functions.
powerpc/ptrace: move register viewing functions out of ptrace.c
powerpc/ptrace: split out TRANSACTIONAL_MEM related functions.
powerpc/ptrace: split out SPE related functions.
powerpc/ptrace: split out ALTIVEC related functions.
powerpc/ptrace: split out VSX related functions.
powerpc/ptrace: drop PARAMETER_SAVE_AREA_OFFSET
powerpc/ptrace: drop unnecessary #ifdefs CONFIG_PPC64
powerpc/ptrace: remove unused header includes
...
* GICv4.1 support
* 32bit host removal
PPC:
* secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
* allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
* New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require bulk
modification of the page tables.
* Initial work on making nested SVM event injection more similar to VMX,
and less buggy.
* Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in function
names which occasionally means eptp, KVM too has standardized on "pgd".
* A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
* Some removal of pointer chasing from kvm_x86_ops, which will also be
switched to static calls as soon as they are available.
* New Tigerlake CPUID features.
* More bugfixes, optimizations and cleanups.
Generic:
* selftests: cleanups, new MMU notifier stress test, steal-time test
* CSV output for kvm_stat.
KVM/MIPS has been broken since 5.5, it does not compile due to a patch committed
by MIPS maintainers. I had already prepared a fix, but the MIPS maintainers
prefer to fix it in generic code rather than KVM so they are taking care of it.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl6GOnIUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMfxwf/ZKLZiRoaovXCOG71M/eHtQb8ZIqU
3MPy+On3eC5Sk/aBxWUL9EFZsbYG6kYdbZ1VOvG9XPBoLlnkDSm/IR0kaELHtnjj
oGVda/tvGn46Ne39y8xBptmb91WDcWH0vFthT/CwlMxAw3xjr+gG7Qyo+8F2CW6m
SSSuLiHSBnyO1cQKruBTHZ8qnR8LlnfXEqtd6Y4LFLic0LbLIoIdRcT3wjQrcZrm
Djd7wbTEYZjUfoqZ72ekwEDUsONcDLDSKcguDO9pSMSCGhpxCVT5Vy68KRpoIMs2
nzNWDKjvqQo5zb2+GWxJgkd12Hv+n7PCXZMbVrWBu1pQsewUns9m4mkpGw==
=6fGt
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- GICv4.1 support
- 32bit host removal
PPC:
- secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
- allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
- New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require
bulk modification of the page tables.
- Initial work on making nested SVM event injection more similar to
VMX, and less buggy.
- Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in
function names which occasionally means eptp, KVM too has
standardized on "pgd".
- A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
- Some removal of pointer chasing from kvm_x86_ops, which will also
be switched to static calls as soon as they are available.
- New Tigerlake CPUID features.
- More bugfixes, optimizations and cleanups.
Generic:
- selftests: cleanups, new MMU notifier stress test, steal-time test
- CSV output for kvm_stat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (277 commits)
x86/kvm: fix a missing-prototypes "vmread_error"
KVM: x86: Fix BUILD_BUG() in __cpuid_entry_get_reg() w/ CONFIG_UBSAN=y
KVM: VMX: Add a trampoline to fix VMREAD error handling
KVM: SVM: Annotate svm_x86_ops as __initdata
KVM: VMX: Annotate vmx_x86_ops as __initdata
KVM: x86: Drop __exit from kvm_x86_ops' hardware_unsetup()
KVM: x86: Copy kvm_x86_ops by value to eliminate layer of indirection
KVM: x86: Set kvm_x86_ops only after ->hardware_setup() completes
KVM: VMX: Configure runtime hooks using vmx_x86_ops
KVM: VMX: Move hardware_setup() definition below vmx_x86_ops
KVM: x86: Move init-only kvm_x86_ops to separate struct
KVM: Pass kvm_init()'s opaque param to additional arch funcs
s390/gmap: return proper error code on ksm unsharing
KVM: selftests: Fix cosmetic copy-paste error in vm_mem_region_move()
KVM: Fix out of range accesses to memslots
KVM: X86: Micro-optimize IPI fastpath delay
KVM: X86: Delay read msr data iff writes ICR MSR
KVM: PPC: Book3S HV: Add a capability for enabling secure guests
KVM: arm64: GICv4.1: Expose HW-based SGIs in debugfs
KVM: arm64: GICv4.1: Allow non-trapping WFI when using HW SGIs
...
This series focuses on corner case bug fixes and general clarity
improvements to hmm_range_fault().
- 9 bug fixes
- Allow pgmap to track the 'owner' of a DEVICE_PRIVATE - in this case the
owner tells the driver if it can understand the DEVICE_PRIVATE page or
not. Use this to resolve a bug in nouveau where it could touch
DEVICE_PRIVATE pages from other drivers.
- Remove a bunch of dead, redundant or unused code and flags
- Clarity improvements to hmm_range_fault()
-----BEGIN PGP SIGNATURE-----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=UEpV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-hmm' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull hmm updates from Jason Gunthorpe:
"This series focuses on corner case bug fixes and general clarity
improvements to hmm_range_fault(). It arose from a review of
hmm_range_fault() by Christoph, Ralph and myself.
hmm_range_fault() is being used by these 'SVM' style drivers to
non-destructively read the page tables. It is very similar to
get_user_pages() except that the output is an array of PFNs and
per-pfn flags, and it has various modes of reading.
This is necessary before RDMA ODP can be converted, as we don't want
to have weird corner case regressions, which is still a looking
forward item. Ralph has a nice tester for this routine, but it is
waiting for feedback from the selftests maintainers.
Summary:
- 9 bug fixes
- Allow pgmap to track the 'owner' of a DEVICE_PRIVATE - in this case
the owner tells the driver if it can understand the DEVICE_PRIVATE
page or not. Use this to resolve a bug in nouveau where it could
touch DEVICE_PRIVATE pages from other drivers.
- Remove a bunch of dead, redundant or unused code and flags
- Clarity improvements to hmm_range_fault()"
* tag 'for-linus-hmm' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (25 commits)
mm/hmm: return error for non-vma snapshots
mm/hmm: do not set pfns when returning an error code
mm/hmm: do not unconditionally set pfns when returning EBUSY
mm/hmm: use device_private_entry_to_pfn()
mm/hmm: remove HMM_FAULT_SNAPSHOT
mm/hmm: remove unused code and tidy comments
mm/hmm: return the fault type from hmm_pte_need_fault()
mm/hmm: remove pgmap checking for devmap pages
mm/hmm: check the device private page owner in hmm_range_fault()
mm: simplify device private page handling in hmm_range_fault
mm: handle multiple owners of device private pages in migrate_vma
memremap: add an owner field to struct dev_pagemap
mm: merge hmm_vma_do_fault into into hmm_vma_walk_hole_
mm/hmm: don't handle the non-fault case in hmm_vma_walk_hole_()
mm/hmm: simplify hmm_vma_walk_hugetlb_entry()
mm/hmm: remove the unused HMM_FAULT_ALLOW_RETRY flag
mm/hmm: don't provide a stub for hmm_range_fault()
mm/hmm: do not check pmd_protnone twice in hmm_vma_handle_pmd()
mm/hmm: add missing call to hmm_pte_need_fault in HMM_PFN_SPECIAL handling
mm/hmm: return -EFAULT when setting HMM_PFN_ERROR on requested valid pages
...
Currently, CONFIG_VHOST depends on CONFIG_VIRTUALIZATION. But vhost is
not necessarily for VM since it's a generic userspace and kernel
communication protocol. Such dependency may prevent archs without
virtualization support from using vhost.
To solve this, a dedicated vhost menu is created under drivers so
CONIFG_VHOST can be decoupled out of CONFIG_VIRTUALIZATION.
While at it, also squash Kconfig.vringh into vhost Kconfig file. This
avoids the trick of conditional inclusion from VOP or CAIF. Then it
will be easier to introduce new vringh users and common dependency for
both vringh and vhost.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20200326140125.19794-2-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows more code to be moved out of unrelocated regions. The
system call KVMTEST is changed to be open-coded and remain in the
tramp area to avoid having to move it to entry_64.S. The custom nature
of the system call entry code means the hcall case can be made more
streamlined than regular interrupt handlers.
mpe: Incorporate fix from Nick:
Moving KVM test to the common entry code missed the case of HMI and
MCE, which do not do __GEN_COMMON_ENTRY (because they don't want to
switch to virt mode).
This means a MCE or HMI exception that is taken while KVM is running a
guest context will not be switched out of that context, and KVM won't
be notified. Found by running sigfuz in guest with patched host on
POWER9 DD2.3, which causes some TM related HMI interrupts (which are
expected and supposed to be handled by KVM).
This fix adds a __GEN_REALMODE_COMMON_ENTRY for those handlers to add
the KVM test. This makes them look a little more like other handlers
that all use __GEN_COMMON_ENTRY.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-13-npiggin@gmail.com
Pass @opaque to kvm_arch_hardware_setup() and
kvm_arch_check_processor_compat() to allow architecture specific code to
reference @opaque without having to stash it away in a temporary global
variable. This will enable x86 to separate its vendor specific callback
ops, which are passed via @opaque, into "init" and "runtime" ops without
having to stash away the "init" ops.
No functional change intended.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Cornelia Huck <cohuck@redhat.com> #s390
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200321202603.19355-2-sean.j.christopherson@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new src_owner field to struct migrate_vma. If the field is set,
only device private pages with page->pgmap->owner equal to that field are
migrated. If the field is not set only "normal" pages are migrated.
Fixes: df6ad69838 ("mm/device-public-memory: device memory cache coherent with CPU")
Link: https://lore.kernel.org/r/20200316193216.920734-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Tested-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add a new opaque owner field to struct dev_pagemap, which will allow the
hmm and migrate_vma code to identify who owns ZONE_DEVICE memory, and
refuse to work on mappings not owned by the calling entity.
Link: https://lore.kernel.org/r/20200316193216.920734-2-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Tested-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
At present, on Power systems with Protected Execution Facility
hardware and an ultravisor, a KVM guest can transition to being a
secure guest at will. Userspace (QEMU) has no way of knowing
whether a host system is capable of running secure guests. This
will present a problem in future when the ultravisor is capable of
migrating secure guests from one host to another, because
virtualization management software will have no way to ensure that
secure guests only run in domains where all of the hosts can
support secure guests.
This adds a VM capability which has two functions: (a) userspace
can query it to find out whether the host can support secure guests,
and (b) userspace can enable it for a guest, which allows that
guest to become a secure guest. If userspace does not enable it,
KVM will return an error when the ultravisor does the hypercall
that indicates that the guest is starting to transition to a
secure guest. The ultravisor will then abort the transition and
the guest will terminate.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
When the call to UV_REGISTER_MEM_SLOT is failing, for instance because
there is not enough free secured memory, the Hypervisor (HV) has to call
UV_RETURN to report the error to the Ultravisor (UV). Then the UV will call
H_SVM_INIT_ABORT to abort the securing phase and go back to the calling VM.
If the kvm->arch.secure_guest is not set, in the return path rfid is called
but there is no valid context to get back to the SVM since the Hcall has
been routed by the Ultravisor.
Move the setting of kvm->arch.secure_guest earlier in
kvmppc_h_svm_init_start() so in the return path, UV_RETURN will be called
instead of rfid.
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Tested-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The Hcall named H_SVM_* are reserved to the Ultravisor. However, nothing
prevent a malicious VM or SVM to call them. This could lead to weird result
and should be filtered out.
Checking the Secure bit of the calling MSR ensure that the call is coming
from either the Ultravisor or a SVM. But any system call made from a SVM
are going through the Ultravisor, and the Ultravisor should filter out
these malicious call. This way, only the Ultravisor is able to make such a
Hcall.
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibnm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With PR KVM, shutting down a VM causes the host kernel to crash:
[ 314.219284] BUG: Unable to handle kernel data access on read at 0xc00800000176c638
[ 314.219299] Faulting instruction address: 0xc008000000d4ddb0
cpu 0x0: Vector: 300 (Data Access) at [c00000036da077a0]
pc: c008000000d4ddb0: kvmppc_mmu_pte_flush_all+0x68/0xd0 [kvm_pr]
lr: c008000000d4dd94: kvmppc_mmu_pte_flush_all+0x4c/0xd0 [kvm_pr]
sp: c00000036da07a30
msr: 900000010280b033
dar: c00800000176c638
dsisr: 40000000
current = 0xc00000036d4c0000
paca = 0xc000000001a00000 irqmask: 0x03 irq_happened: 0x01
pid = 1992, comm = qemu-system-ppc
Linux version 5.6.0-master-gku+ (greg@palmb) (gcc version 7.5.0 (Ubuntu 7.5.0-3ubuntu1~18.04)) #17 SMP Wed Mar 18 13:49:29 CET 2020
enter ? for help
[c00000036da07ab0] c008000000d4fbe0 kvmppc_mmu_destroy_pr+0x28/0x60 [kvm_pr]
[c00000036da07ae0] c0080000009eab8c kvmppc_mmu_destroy+0x34/0x50 [kvm]
[c00000036da07b00] c0080000009e50c0 kvm_arch_vcpu_destroy+0x108/0x140 [kvm]
[c00000036da07b30] c0080000009d1b50 kvm_vcpu_destroy+0x28/0x80 [kvm]
[c00000036da07b60] c0080000009e4434 kvm_arch_destroy_vm+0xbc/0x190 [kvm]
[c00000036da07ba0] c0080000009d9c2c kvm_put_kvm+0x1d4/0x3f0 [kvm]
[c00000036da07c00] c0080000009da760 kvm_vm_release+0x38/0x60 [kvm]
[c00000036da07c30] c000000000420be0 __fput+0xe0/0x310
[c00000036da07c90] c0000000001747a0 task_work_run+0x150/0x1c0
[c00000036da07cf0] c00000000014896c do_exit+0x44c/0xd00
[c00000036da07dc0] c0000000001492f4 do_group_exit+0x64/0xd0
[c00000036da07e00] c000000000149384 sys_exit_group+0x24/0x30
[c00000036da07e20] c00000000000b9d0 system_call+0x5c/0x68
This is caused by a use-after-free in kvmppc_mmu_pte_flush_all()
which dereferences vcpu->arch.book3s which was previously freed by
kvmppc_core_vcpu_free_pr(). This happens because kvmppc_mmu_destroy()
is called after kvmppc_core_vcpu_free() since commit ff030fdf55
("KVM: PPC: Move kvm_vcpu_init() invocation to common code").
The kvmppc_mmu_destroy() helper calls one of the following depending
on the KVM backend:
- kvmppc_mmu_destroy_hv() which does nothing (Book3s HV)
- kvmppc_mmu_destroy_pr() which undoes the effects of
kvmppc_mmu_init() (Book3s PR 32-bit)
- kvmppc_mmu_destroy_pr() which undoes the effects of
kvmppc_mmu_init() (Book3s PR 64-bit)
- kvmppc_mmu_destroy_e500() which does nothing (BookE e500/e500mc)
It turns out that this is only relevant to PR KVM actually. And both
32 and 64 backends need vcpu->arch.book3s to be valid when calling
kvmppc_mmu_destroy_pr(). So instead of calling kvmppc_mmu_destroy()
from kvm_arch_vcpu_destroy(), call kvmppc_mmu_destroy_pr() at the
beginning of kvmppc_core_vcpu_free_pr(). This is consistent with
kvmppc_mmu_init() being the last call in kvmppc_core_vcpu_create_pr().
For the same reason, if kvmppc_core_vcpu_create_pr() returns an
error then this means that kvmppc_mmu_init() was either not called
or failed, in which case kvmppc_mmu_destroy() should not be called.
Drop the line in the error path of kvm_arch_vcpu_create().
Fixes: ff030fdf55 ("KVM: PPC: Move kvm_vcpu_init() invocation to common code")
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/158455341029.178873.15248663726399374882.stgit@bahia.lan
These are only used by HV KVM and BookE, and in both cases they are
nops.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This is only relevant to PR KVM. Make it obvious by moving the
function declaration to the Book3s header and rename it with
a _pr suffix.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With PR KVM, shutting down a VM causes the host kernel to crash:
[ 314.219284] BUG: Unable to handle kernel data access on read at 0xc00800000176c638
[ 314.219299] Faulting instruction address: 0xc008000000d4ddb0
cpu 0x0: Vector: 300 (Data Access) at [c00000036da077a0]
pc: c008000000d4ddb0: kvmppc_mmu_pte_flush_all+0x68/0xd0 [kvm_pr]
lr: c008000000d4dd94: kvmppc_mmu_pte_flush_all+0x4c/0xd0 [kvm_pr]
sp: c00000036da07a30
msr: 900000010280b033
dar: c00800000176c638
dsisr: 40000000
current = 0xc00000036d4c0000
paca = 0xc000000001a00000 irqmask: 0x03 irq_happened: 0x01
pid = 1992, comm = qemu-system-ppc
Linux version 5.6.0-master-gku+ (greg@palmb) (gcc version 7.5.0 (Ubuntu 7.5.0-3ubuntu1~18.04)) #17 SMP Wed Mar 18 13:49:29 CET 2020
enter ? for help
[c00000036da07ab0] c008000000d4fbe0 kvmppc_mmu_destroy_pr+0x28/0x60 [kvm_pr]
[c00000036da07ae0] c0080000009eab8c kvmppc_mmu_destroy+0x34/0x50 [kvm]
[c00000036da07b00] c0080000009e50c0 kvm_arch_vcpu_destroy+0x108/0x140 [kvm]
[c00000036da07b30] c0080000009d1b50 kvm_vcpu_destroy+0x28/0x80 [kvm]
[c00000036da07b60] c0080000009e4434 kvm_arch_destroy_vm+0xbc/0x190 [kvm]
[c00000036da07ba0] c0080000009d9c2c kvm_put_kvm+0x1d4/0x3f0 [kvm]
[c00000036da07c00] c0080000009da760 kvm_vm_release+0x38/0x60 [kvm]
[c00000036da07c30] c000000000420be0 __fput+0xe0/0x310
[c00000036da07c90] c0000000001747a0 task_work_run+0x150/0x1c0
[c00000036da07cf0] c00000000014896c do_exit+0x44c/0xd00
[c00000036da07dc0] c0000000001492f4 do_group_exit+0x64/0xd0
[c00000036da07e00] c000000000149384 sys_exit_group+0x24/0x30
[c00000036da07e20] c00000000000b9d0 system_call+0x5c/0x68
This is caused by a use-after-free in kvmppc_mmu_pte_flush_all()
which dereferences vcpu->arch.book3s which was previously freed by
kvmppc_core_vcpu_free_pr(). This happens because kvmppc_mmu_destroy()
is called after kvmppc_core_vcpu_free() since commit ff030fdf55
("KVM: PPC: Move kvm_vcpu_init() invocation to common code").
The kvmppc_mmu_destroy() helper calls one of the following depending
on the KVM backend:
- kvmppc_mmu_destroy_hv() which does nothing (Book3s HV)
- kvmppc_mmu_destroy_pr() which undoes the effects of
kvmppc_mmu_init() (Book3s PR 32-bit)
- kvmppc_mmu_destroy_pr() which undoes the effects of
kvmppc_mmu_init() (Book3s PR 64-bit)
- kvmppc_mmu_destroy_e500() which does nothing (BookE e500/e500mc)
It turns out that this is only relevant to PR KVM actually. And both
32 and 64 backends need vcpu->arch.book3s to be valid when calling
kvmppc_mmu_destroy_pr(). So instead of calling kvmppc_mmu_destroy()
from kvm_arch_vcpu_destroy(), call kvmppc_mmu_destroy_pr() at the
beginning of kvmppc_core_vcpu_free_pr(). This is consistent with
kvmppc_mmu_init() being the last call in kvmppc_core_vcpu_create_pr().
For the same reason, if kvmppc_core_vcpu_create_pr() returns an
error then this means that kvmppc_mmu_init() was either not called
or failed, in which case kvmppc_mmu_destroy() should not be called.
Drop the line in the error path of kvm_arch_vcpu_create().
Fixes: ff030fdf55 ("KVM: PPC: Move kvm_vcpu_init() invocation to common code")
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The h_cede_tm kvm-unit-test currently fails when run inside an L1 guest
via the guest/nested hypervisor.
./run-tests.sh -v
...
TESTNAME=h_cede_tm TIMEOUT=90s ACCEL= ./powerpc/run powerpc/tm.elf -smp 2,threads=2 -machine cap-htm=on -append "h_cede_tm"
FAIL h_cede_tm (2 tests, 1 unexpected failures)
While the test relates to transactional memory instructions, the actual
failure is due to the return code of the H_CEDE hypercall, which is
reported as 224 instead of 0. This happens even when no TM instructions
are issued.
224 is the value placed in r3 to execute a hypercall for H_CEDE, and r3
is where the caller expects the return code to be placed upon return.
In the case of guest running under a nested hypervisor, issuing H_CEDE
causes a return from H_ENTER_NESTED. In this case H_CEDE is
specially-handled immediately rather than later in
kvmppc_pseries_do_hcall() as with most other hcalls, but we forget to
set the return code for the caller, hence why kvm-unit-test sees the
224 return code and reports an error.
Guest kernels generally don't check the return value of H_CEDE, so
that likely explains why this hasn't caused issues outside of
kvm-unit-tests so far.
Fix this by setting r3 to 0 after we finish processing the H_CEDE.
RHBZ: 1778556
Fixes: 4bad77799f ("KVM: PPC: Book3S HV: Handle hypercalls correctly when nested")
Cc: linuxppc-dev@ozlabs.org
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On P9 DD2.2 due to a CPU defect some TM instructions need to be emulated by
KVM. This is handled at first by the hardware raising a softpatch interrupt
when certain TM instructions that need KVM assistance are executed in the
guest. Althought some TM instructions per Power ISA are invalid forms they
can raise a softpatch interrupt too. For instance, 'tresume.' instruction
as defined in the ISA must have bit 31 set (1), but an instruction that
matches 'tresume.' PO and XO opcode fields but has bit 31 not set (0), like
0x7cfe9ddc, also raises a softpatch interrupt. Similarly for 'treclaim.'
and 'trechkpt.' instructions with bit 31 = 0, i.e. 0x7c00075c and
0x7c0007dc, respectively. Hence, if a code like the following is executed
in the guest it will raise a softpatch interrupt just like a 'tresume.'
when the TM facility is enabled ('tabort. 0' in the example is used only
to enable the TM facility):
int main() { asm("tabort. 0; .long 0x7cfe9ddc;"); }
Currently in such a case KVM throws a complete trace like:
[345523.705984] WARNING: CPU: 24 PID: 64413 at arch/powerpc/kvm/book3s_hv_tm.c:211 kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.705985] Modules linked in: kvm_hv(E) xt_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp ip6table_mangle ip6table_nat
iptable_mangle iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ebtable_filter ebtables ip6table_filter
ip6_tables iptable_filter bridge stp llc sch_fq_codel ipmi_powernv at24 vmx_crypto ipmi_devintf ipmi_msghandler
ibmpowernv uio_pdrv_genirq kvm opal_prd uio leds_powernv ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp
libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx libcrc32c xor raid6_pq raid1 raid0 multipath linear tg3
crct10dif_vpmsum crc32c_vpmsum ipr [last unloaded: kvm_hv]
[345523.706030] CPU: 24 PID: 64413 Comm: CPU 0/KVM Tainted: G W E 5.5.0+ #1
[345523.706031] NIP: c0080000072cb9c0 LR: c0080000072b5e80 CTR: c0080000085c7850
[345523.706034] REGS: c000000399467680 TRAP: 0700 Tainted: G W E (5.5.0+)
[345523.706034] MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 24022428 XER: 00000000
[345523.706042] CFAR: c0080000072b5e7c IRQMASK: 0
GPR00: c0080000072b5e80 c000000399467910 c0080000072db500 c000000375ccc720
GPR04: c000000375ccc720 00000003fbec0000 0000a10395dda5a6 0000000000000000
GPR08: 000000007cfe9ddc 7cfe9ddc000005dc 7cfe9ddc7c0005dc c0080000072cd530
GPR12: c0080000085c7850 c0000003fffeb800 0000000000000001 00007dfb737f0000
GPR16: c0002001edcca558 0000000000000000 0000000000000000 0000000000000001
GPR20: c000000001b21258 c0002001edcca558 0000000000000018 0000000000000000
GPR24: 0000000001000000 ffffffffffffffff 0000000000000001 0000000000001500
GPR28: c0002001edcc4278 c00000037dd80000 800000050280f033 c000000375ccc720
[345523.706062] NIP [c0080000072cb9c0] kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.706065] LR [c0080000072b5e80] kvmppc_handle_exit_hv.isra.53+0x3e8/0x798 [kvm_hv]
[345523.706066] Call Trace:
[345523.706069] [c000000399467910] [c000000399467940] 0xc000000399467940 (unreliable)
[345523.706071] [c000000399467950] [c000000399467980] 0xc000000399467980
[345523.706075] [c0000003994679f0] [c0080000072bd1c4] kvmhv_run_single_vcpu+0xa1c/0xb80 [kvm_hv]
[345523.706079] [c000000399467ac0] [c0080000072bd8e0] kvmppc_vcpu_run_hv+0x5b8/0xb00 [kvm_hv]
[345523.706087] [c000000399467b90] [c0080000085c93cc] kvmppc_vcpu_run+0x34/0x48 [kvm]
[345523.706095] [c000000399467bb0] [c0080000085c582c] kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm]
[345523.706101] [c000000399467c40] [c0080000085b7498] kvm_vcpu_ioctl+0x3d0/0x7b0 [kvm]
[345523.706105] [c000000399467db0] [c0000000004adf9c] ksys_ioctl+0x13c/0x170
[345523.706107] [c000000399467e00] [c0000000004adff8] sys_ioctl+0x28/0x80
[345523.706111] [c000000399467e20] [c00000000000b278] system_call+0x5c/0x68
[345523.706112] Instruction dump:
[345523.706114] 419e0390 7f8a4840 409d0048 6d497c00 2f89075d 419e021c 6d497c00 2f8907dd
[345523.706119] 419e01c0 6d497c00 2f8905dd 419e00a4 <0fe00000> 38210040 38600000 ebc1fff0
and then treats the executed instruction as a 'nop'.
However the POWER9 User's Manual, in section "4.6.10 Book II Invalid
Forms", informs that for TM instructions bit 31 is in fact ignored, thus
for the TM-related invalid forms ignoring bit 31 and handling them like the
valid forms is an acceptable way to handle them. POWER8 behaves the same
way too.
This commit changes the handling of the cases here described by treating
the TM-related invalid forms that can generate a softpatch interrupt
just like their valid forms (w/ bit 31 = 1) instead of as a 'nop' and by
gently reporting any other unrecognized case to the host and treating it as
illegal instruction instead of throwing a trace and treating it as a 'nop'.
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-By: Michael Neuling <mikey@neuling.org>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In kvmppc_unmap_free_pte() in book3s_64_mmu_radix.c, we use the
non-constant value PTE_INDEX_SIZE to clear a PTE page.
We can instead use the constant RADIX_PTE_INDEX_SIZE, because we know
this code will only be running when the Radix MMU is active.
Note that we already use RADIX_PTE_INDEX_SIZE for the allocation of
kvm_pte_cache.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This makes the same changes in the page fault handler for HPT guests
that commits 31c8b0d069 ("KVM: PPC: Book3S HV: Use __gfn_to_pfn_memslot()
in page fault handler", 2018-03-01), 71d29f43b6 ("KVM: PPC: Book3S HV:
Don't use compound_order to determine host mapping size", 2018-09-11)
and 6579804c43 ("KVM: PPC: Book3S HV: Avoid crash from THP collapse
during radix page fault", 2018-10-04) made for the page fault handler
for radix guests.
In summary, where we used to call get_user_pages_fast() and then do
special handling for VM_PFNMAP vmas, we now call __get_user_pages_fast()
and then __gfn_to_pfn_memslot() if that fails, followed by reading the
Linux PTE to get the host PFN, host page size and mapping attributes.
This also brings in the change from SetPageDirty() to set_page_dirty_lock()
which was done for the radix page fault handler in commit c3856aeb29
("KVM: PPC: Book3S HV: Fix handling of large pages in radix page fault
handler", 2018-02-23).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Remove includes of asm/kvm_host.h from files that already include
linux/kvm_host.h to make it more obvious that there is no ordering issue
between the two headers. linux/kvm_host.h includes asm/kvm_host.h to
pick up architecture specific settings, and this will never change, i.e.
including asm/kvm_host.h after linux/kvm_host.h may seem problematic,
but in practice is simply redundant.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Refactor memslot handling to treat the number of used slots as the de
facto size of the memslot array, e.g. return NULL from id_to_memslot()
when an invalid index is provided instead of relying on npages==0 to
detect an invalid memslot. Rework the sorting and walking of memslots
in advance of dynamically sizing memslots to aid bisection and debug,
e.g. with luck, a bug in the refactoring will bisect here and/or hit a
WARN instead of randomly corrupting memory.
Alternatively, a global null/invalid memslot could be returned, i.e. so
callers of id_to_memslot() don't have to explicitly check for a NULL
memslot, but that approach runs the risk of introducing difficult-to-
debug issues, e.g. if the global null slot is modified. Constifying
the return from id_to_memslot() to combat such issues is possible, but
would require a massive refactoring of arch specific code and would
still be susceptible to casting shenanigans.
Add function comments to update_memslots() and search_memslots() to
explicitly (and loudly) state how memslots are sorted.
Opportunistically stuff @hva with a non-canonical value when deleting a
private memslot on x86 to detect bogus usage of the freed slot.
No functional change intended.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rework kvm_get_dirty_log() so that it "returns" the associated memslot
on success. A future patch will rework memslot handling such that
id_to_memslot() can return NULL, returning the memslot makes it more
obvious that the validity of the memslot has been verified, i.e.
precludes the need to add validity checks in the arch code that are
technically unnecessary.
To maintain ordering in s390, move the call to kvm_arch_sync_dirty_log()
from s390's kvm_vm_ioctl_get_dirty_log() to the new kvm_get_dirty_log().
This is a nop for PPC, the only other arch that doesn't select
KVM_GENERIC_DIRTYLOG_READ_PROTECT, as its sync_dirty_log() is empty.
Ideally, moving the sync_dirty_log() call would be done in a separate
patch, but it can't be done in a follow-on patch because that would
temporarily break s390's ordering. Making the move in a preparatory
patch would be functionally correct, but would create an odd scenario
where the moved sync_dirty_log() would operate on a "different" memslot
due to consuming the result of a different id_to_memslot(). The
memslot couldn't actually be different as slots_lock is held, but the
code is confusing enough as it is, i.e. moving sync_dirty_log() in this
patch is the lesser of all evils.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the implementations of KVM_GET_DIRTY_LOG and KVM_CLEAR_DIRTY_LOG
for CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT into common KVM code.
The arch specific implemenations are extremely similar, differing
only in whether the dirty log needs to be sync'd from hardware (x86)
and how the TLBs are flushed. Add new arch hooks to handle sync
and TLB flush; the sync will also be used for non-generic dirty log
support in a future patch (s390).
The ulterior motive for providing a common implementation is to
eliminate the dependency between arch and common code with respect to
the memslot referenced by the dirty log, i.e. to make it obvious in the
code that the validity of the memslot is guaranteed, as a future patch
will rework memslot handling such that id_to_memslot() can return NULL.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all callers of kvm_free_memslot() pass NULL for @dont, remove
the param from the top-level routine and all arch's implementations.
No functional change intended.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the "const" attribute from @old in kvm_arch_commit_memory_region()
to allow arch specific code to free arch specific resources in the old
memslot without having to cast away the attribute. Freeing resources in
kvm_arch_commit_memory_region() paves the way for simplifying
kvm_free_memslot() by eliminating the last usage of its @dont param.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_arch_create_memslot() now that all arch implementations are
effectively nops. Removing kvm_arch_create_memslot() eliminates the
possibility for arch specific code to allocate memory prior to setting
a memslot, which sets the stage for simplifying kvm_free_memslot().
Cc: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allocate the rmap array during kvm_arch_prepare_memory_region() to pave
the way for removing kvm_arch_create_memslot() altogether. Moving PPC's
memory allocation only changes the order of kernel memory allocations
between PPC and common KVM code.
No functional change intended.
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because of this cleanup, we get to remove a few fields in struct
kvm_arch that are now unused.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mpe: Fix build error in kvm/timing.c, adapt kvmppc_remove_cpu_debugfs()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200209105901.1620958-2-gregkh@linuxfoundation.org
- Implement user_access_begin() and friends for our platforms that support
controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure" virtual
machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit VDSO, and
some other improvements.
- A series to use the PCI hotplug framework to control opencapi card's so that
they can be reset and re-read after flashing a new FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to:
Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen Zhou, Christophe Leroy,
Frederic Barrat, Greg Kurz, Jason A. Donenfeld, Joel Stanley, Jordan Niethe,
Julia Lawall, Krzysztof Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus
Walleij, Michael Bringmann, Nathan Chancellor, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy
Dunlap, Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago Jung
Bauermann, Tyrel Datwyler, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----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=xpG+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A pretty small batch for us, and apologies for it being a bit late, I
wanted to sneak Christophe's user_access_begin() series in.
Summary:
- Implement user_access_begin() and friends for our platforms that
support controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure"
virtual machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit
VDSO, and some other improvements.
- A series to use the PCI hotplug framework to control opencapi
card's so that they can be reset and re-read after flashing a new
FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to: Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy,
Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen
Zhou, Christophe Leroy, Frederic Barrat, Greg Kurz, Jason A.
Donenfeld, Joel Stanley, Jordan Niethe, Julia Lawall, Krzysztof
Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus Walleij, Michael
Bringmann, Nathan Chancellor, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy Dunlap,
Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain"
* tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (131 commits)
powerpc: configs: Cleanup old Kconfig options
powerpc/configs/skiroot: Enable some more hardening options
powerpc/configs/skiroot: Disable xmon default & enable reboot on panic
powerpc/configs/skiroot: Enable security features
powerpc/configs/skiroot: Update for symbol movement only
powerpc/configs/skiroot: Drop default n CONFIG_CRYPTO_ECHAINIV
powerpc/configs/skiroot: Drop HID_LOGITECH
powerpc/configs: Drop NET_VENDOR_HP which moved to staging
powerpc/configs: NET_CADENCE became NET_VENDOR_CADENCE
powerpc/configs: Drop CONFIG_QLGE which moved to staging
powerpc: Do not consider weak unresolved symbol relocations as bad
powerpc/32s: Fix kasan_early_hash_table() for CONFIG_VMAP_STACK
powerpc: indent to improve Kconfig readability
powerpc: Provide initial documentation for PAPR hcalls
powerpc: Implement user_access_save() and user_access_restore()
powerpc: Implement user_access_begin and friends
powerpc/32s: Prepare prevent_user_access() for user_access_end()
powerpc/32s: Drop NULL addr verification
powerpc/kuap: Fix set direction in allow/prevent_user_access()
powerpc/32s: Fix bad_kuap_fault()
...
* Fix compile warning on 32-bit machines
* Fix locking error in secure VM support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJeMiC8AAoJEJ2a6ncsY3GfGg8H/03p+jc/aCKcA75ZeQPlzhmu
KWvSBbPATNcQiYOLfIvbB9AMXUPoyIfiblW/On8G6COFypsIhhUTwEfPUjWIBHNX
IwCfzoyf0gDRTi7A7gTDD06ZE+stikxJu59agX2Gc8kTIQ8ge340VR8J95Ol8/n2
/hVA8S/ORrdv8/KaCcvvIwc1V7OV6xBuGsTUOUvywzBTGDKd0CAbNzRwtS8LmWcM
OCkZX4G5DpFIYdsnjSBaSfwEVPAf3G1DzyQ801emwRnbAGYYgfakd1LwqdLDxptt
6CFHuIENEmmweJKMf9FBLWg+fOMl8wsv9l4mBIYt7coq5XPpi07yJ6yqSaJEToQ=
=Hmfo
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
Second KVM PPC update for 5.6
* Fix compile warning on 32-bit machines
* Fix locking error in secure VM support
Fixes: 3a167beac0 ("kvm: powerpc: Add kvmppc_ops callback")
Signed-off-by: David Michael <fedora.dm0@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When migrate_vma_setup() fails in kvmppc_svm_page_out(),
release kvm->arch.uvmem_lock before returning.
Fixes: ca9f494267 ("KVM: PPC: Book3S HV: Support for running secure guests")
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Use kvm_vcpu_gfn_to_hva() when retrieving the host page size so that the
correct set of memslots is used when handling x86 page faults in SMM.
Fixes: 54bf36aac5 ("KVM: x86: use vcpu-specific functions to read/write/translate GFNs")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_arch_vcpu_init() and kvm_arch_vcpu_uninit() now that all
arch specific implementations are nops.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fold init() into create() now that the two are called back-to-back by
common KVM code (kvm_vcpu_init() calls kvm_arch_vcpu_init() as its last
action, and kvm_vm_ioctl_create_vcpu() calls kvm_arch_vcpu_create()
immediately thereafter). Rinse and repeat for kvm_arch_vcpu_uninit()
and kvm_arch_vcpu_destroy(). This paves the way for removing
kvm_arch_vcpu_{un}init() entirely.
Note, calling kvmppc_mmu_destroy() if kvmppc_core_vcpu_create() fails
may or may not be necessary. Move it along with the more obvious call
to kvmppc_subarch_vcpu_uninit() so as not to inadvertantly introduce a
functional change and/or bug.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_arch_vcpu_setup() now that all arch specific implementations
are nops.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fold setup() into create() now that the two are called back-to-back by
common KVM code. This paves the way for removing kvm_arch_vcpu_setup().
Note, BookE directly implements kvm_arch_vcpu_setup() and PPC's common
kvm_arch_vcpu_create() is responsible for its own cleanup, thus the only
cleanup required when directly invoking kvmppc_core_vcpu_setup() is to
call .vcpu_free(), which is the BookE specific portion of PPC's
kvm_arch_vcpu_destroy() by way of kvmppc_core_vcpu_free().
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all architectures tightly couple vcpu allocation/free with the
mandatory calls to kvm_{un}init_vcpu(), move the sequences verbatim to
common KVM code.
Move both allocation and initialization in a single patch to eliminate
thrash in arch specific code. The bisection benefits of moving the two
pieces in separate patches is marginal at best, whereas the odds of
introducing a transient arch specific bug are non-zero.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit a25bd72bad ("powerpc/mm/radix: Workaround prefetch issue with
KVM") introduced a number of workarounds as coming out of a guest with
the mmu enabled would make the cpu would start running in hypervisor
state with the PID value from the guest. The cpu will then start
prefetching for the hypervisor with that PID value.
In Power9 DD2.2 the cpu behaviour was modified to fix this. When
accessing Quadrant 0 in hypervisor mode with LPID != 0 prefetching will
not be performed. This means that we can get rid of the workarounds for
Power9 DD2.2 and later revisions. Add a new cpu feature
CPU_FTR_P9_RADIX_PREFETCH_BUG to indicate if the workarounds are needed.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191206031722.25781-1-jniethe5@gmail.com
Add kvm_vcpu_destroy() and wire up all architectures to call the common
function instead of their arch specific implementation. The common
destruction function will be used by future patches to move allocation
and initialization of vCPUs to common KVM code, i.e. to free resources
that are allocated by arch agnostic code.
No functional change intended.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a pre-allocation arch hook to handle checks that are currently done
by arch specific code prior to allocating the vCPU object. This paves
the way for moving the allocation to common KVM code.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the superfluous kvm_arch_vcpu_free() as it is no longer called
from commmon KVM code. Note, kvm_arch_vcpu_destroy() *is* called from
common code, i.e. choosing which function to whack is not completely
arbitrary.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the kvm_cpu_{un}init() calls to common PPC code as an intermediate
step towards removing kvm_cpu_{un}init() altogether.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the initialization of oldpir so that the call to kvm_vcpu_init() is
at the top of kvmppc_core_vcpu_create_e500mc(). oldpir is only use
when loading/putting a vCPU, which currently cannot be done until after
kvm_arch_vcpu_create() completes. Reording the call to kvm_vcpu_init()
paves the way for moving the invocation to common PPC code.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_vcpu_init() in kvmppc_core_vcpu_create_pr() prior to allocating
the book3s and shadow_vcpu objects in preparation of moving said call to
common PPC code. Although kvm_vcpu_init() has an arch callback, the
callback is empty for Book3S PR, i.e. barring unseen black magic, moving
the allocation has no real functional impact.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move allocation of all flavors of PPC vCPUs to common PPC code. All
variants either allocate 'struct kvm_vcpu' directly, or require that
the embedded 'struct kvm_vcpu' member be located at offset 0, i.e.
guarantee that the allocation can be directly interpreted as a 'struct
kvm_vcpu' object.
Remove the message from the build-time assertion regarding placement of
the struct, as compatibility with the arch usercopy region is no longer
the sole dependent on 'struct kvm_vcpu' being at offset zero.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation for moving vcpu allocation to common PPC code, add an
explicit, albeit redundant, build-time assert to ensure the vcpu member
is located at offset 0. The assert is redundant in the sense that
kvmppc_core_vcpu_create_e500() contains a functionally identical assert.
The motiviation for adding the extra assert is to provide visual
confirmation of the correctness of moving vcpu allocation to common
code.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Explicitly free the shared page if kvmppc_mmu_init() fails during
kvmppc_core_vcpu_create(), as the page is freed only in
kvmppc_core_vcpu_free(), which is not reached via kvm_vcpu_uninit().
Fixes: 96bc451a15 ("KVM: PPC: Introduce shared page")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_vcpu_uninit() if vcore creation fails to avoid leaking any
resources allocated by kvm_vcpu_init(), i.e. the vcpu->run page.
Fixes: 371fefd6f2 ("KVM: PPC: Allow book3s_hv guests to use SMT processor modes")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement the H_SVM_INIT_ABORT hcall which the Ultravisor can use to
abort an SVM after it has issued the H_SVM_INIT_START and before the
H_SVM_INIT_DONE hcalls. This hcall could be used when Ultravisor
encounters security violations or other errors when starting an SVM.
Note that this hcall is different from UV_SVM_TERMINATE ucall which
is used by HV to terminate/cleanup an VM that has becore secure.
The H_SVM_INIT_ABORT basically undoes operations that were done
since the H_SVM_INIT_START hcall - i.e page-out all the VM pages back
to normal memory, and terminate the SVM.
(If we do not bring the pages back to normal memory, the text/data
of the VM would be stuck in secure memory and since the SVM did not
go secure, its MSR_S bit will be clear and the VM wont be able to
access its pages even to do a clean exit).
Based on patches and discussion with Paul Mackerras, Ram Pai and
Bharata Rao.
Signed-off-by: Ram Pai <linuxram@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Add 'skip_page_out' parameter to kvmppc_uvmem_drop_pages() so the
callers can specify whetheter or not to skip paging out pages. This
will be needed in a follow-on patch that implements H_SVM_INIT_ABORT
hcall.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Given that in kvm_create_vm() there is:
kvm->mm = current->mm;
And that on every kvm_*_ioctl we have:
if (kvm->mm != current->mm)
return -EIO;
I see no reason to keep using current->mm instead of kvm->mm.
By doing so, we would reduce the use of 'global' variables on code, relying
more in the contents of kvm struct.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Given that in kvm_create_vm() there is:
kvm->mm = current->mm;
And that on every kvm_*_ioctl we have:
if (kvm->mm != current->mm)
return -EIO;
I see no reason to keep using current->mm instead of kvm->mm.
By doing so, we would reduce the use of 'global' variables on code, relying
more in the contents of kvm struct.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Fixes gcc '-Wunused-but-set-variable' warning:
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:6: warning: variable ra set but not used [-Wunused-but-set-variable]
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:10: warning: variable rs set but not used [-Wunused-but-set-variable]
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:14: warning: variable rt set but not used [-Wunused-but-set-variable]
They are not used since commit 2b33cb585f ("KVM: PPC: Reimplement
LOAD_FP/STORE_FP instruction mmio emulation with analyse_instr() input")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
* Fix a bug where we try to do an ultracall on a system without an ultravisor.
KVM:
- Fix uninitialised sysreg accessor
- Fix handling of demand-paged device mappings
- Stop spamming the console on IMPDEF sysregs
- Relax mappings of writable memslots
- Assorted cleanups
MIPS:
- Now orphan, James Hogan is stepping down
x86:
- MAINTAINERS change, so long Radim and thanks for all the fish
- supported CPUID fixes for AMD machines without SPEC_CTRL
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJd/1+WAAoJEL/70l94x66DFuYH/A8x/P6BuCpppdGoEw+VGy7X
E8141dHTd7b1Wgi0kDNLRREr4QIfArvavGe0z0W8p4fGtcVjXdyhhfPd0UK6dfKG
9P66phY4AGPjde/8q/qSdFup9yshpcFwSVYdRC0L1w86dBRlXwuqk6K5zsRyCU4b
38v5Q3rPdMnWWB0K88/GMvAyQmPkgMOXJvhoecKeDQ+9IZ3ub6DBBNGM/xTJ9Y3z
vUe2BoYkZ3KKn6sfP66PdprBVI1EOrrAoj/l4BSuo/yUPcQsxTihXMkh5iGl18TF
h7TN9eq2Bn2ryh0TsaSK8opuePcotVvx7oll3ERtSV4e+89z5FDt4vVcY1VyRuc=
=adm7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"PPC:
- Fix a bug where we try to do an ultracall on a system without an
ultravisor
KVM:
- Fix uninitialised sysreg accessor
- Fix handling of demand-paged device mappings
- Stop spamming the console on IMPDEF sysregs
- Relax mappings of writable memslots
- Assorted cleanups
MIPS:
- Now orphan, James Hogan is stepping down
x86:
- MAINTAINERS change, so long Radim and thanks for all the fish
- supported CPUID fixes for AMD machines without SPEC_CTRL"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
MAINTAINERS: remove Radim from KVM maintainers
MAINTAINERS: Orphan KVM for MIPS
kvm: x86: Host feature SSBD doesn't imply guest feature AMD_SSBD
kvm: x86: Host feature SSBD doesn't imply guest feature SPEC_CTRL_SSBD
KVM: PPC: Book3S HV: Don't do ultravisor calls on systems without ultravisor
KVM: arm/arm64: Properly handle faulting of device mappings
KVM: arm64: Ensure 'params' is initialised when looking up sys register
KVM: arm/arm64: Remove excessive permission check in kvm_arch_prepare_memory_region
KVM: arm64: Don't log IMP DEF sysreg traps
KVM: arm64: Sanely ratelimit sysreg messages
KVM: arm/arm64: vgic: Use wrapper function to lock/unlock all vcpus in kvm_vgic_create()
KVM: arm/arm64: vgic: Fix potential double free dist->spis in __kvm_vgic_destroy()
KVM: arm/arm64: Get rid of unused arg in cpu_init_hyp_mode()
Commit 22945688ac ("KVM: PPC: Book3S HV: Support reset of secure
guest") added a call to uv_svm_terminate, which is an ultravisor
call, without any check that the guest is a secure guest or even that
the system has an ultravisor. On a system without an ultravisor,
the ultracall will degenerate to a hypercall, but since we are not
in KVM guest context, the hypercall will get treated as a system
call, which could have random effects depending on what happens to
be in r0, and could also corrupt the current task's kernel stack.
Hence this adds a test for the guest being a secure guest before
doing uv_svm_terminate().
Fixes: 22945688ac ("KVM: PPC: Book3S HV: Support reset of secure guest")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
VCPU_CR is the offset of arch.regs.ccr in kvm_vcpu.
arch/powerpc/include/asm/kvm_host.h defines arch.regs as a struct
pt_regs, and arch/powerpc/include/asm/ptrace.h defines the ccr field
of pt_regs as "unsigned long ccr". Since unsigned long is 64 bits, a
64-bit load needs to be used to load it, unless an endianness specific
correction offset is added to access the desired subpart. In this
case there is no reason to _not_ use a 64 bit load though.
Fixes: 6c85b7bc63 ("powerpc/kvm: Use UV_RETURN ucall to return to ultravisor")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Marcus Comstedt <marcus@mc.pp.se>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191215094900.46740-1-marcus@mc.pp.se
* small x86 cleanup
* fix for an x86-specific out-of-bounds write on a ioctl (not guest triggerable,
data not attacker-controlled)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJd551cAAoJEL/70l94x66D+JkH/R3eEOyvckPmYmzd0lnV8mQ/
7e0n2G/aD+iLZkcCbUnMaImdmSJmoEEJCPjgPk/5nJ3zUi5b/ABWyidEM5uf19Hl
rzKBg0DR7BiQptPnZv2JMwEVKu3JOTchMykqu9xXChQlICocZ0xjdOA6nQ19p0Lv
FulDw5MUaWrXevIzCBskQ38zJejRQA6CpD1lQkHn7LKS9p3p+BsAOd/Ouy87RfWG
b3ktECNbXyO6KStrrhgm+z8pviWY+kqYklyBlDOOwxWif0x8WvNDpQLoVo+ZuhLU
Me8YJ1BN75vFlxzh6ZK5exBUnm9E3fGVKIaaF+dpuds2x+j4HnYl+lZCm89MdqY=
=Q4v7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
- PPC secure guest support
- small x86 cleanup
- fix for an x86-specific out-of-bounds write on a ioctl (not guest
triggerable, data not attacker-controlled)
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vmx: Stop wasting a page for guest_msrs
KVM: x86: fix out-of-bounds write in KVM_GET_EMULATED_CPUID (CVE-2019-19332)
Documentation: kvm: Fix mention to number of ioctls classes
powerpc: Ultravisor: Add PPC_UV config option
KVM: PPC: Book3S HV: Support reset of secure guest
KVM: PPC: Book3S HV: Handle memory plug/unplug to secure VM
KVM: PPC: Book3S HV: Radix changes for secure guest
KVM: PPC: Book3S HV: Shared pages support for secure guests
KVM: PPC: Book3S HV: Support for running secure guests
mm: ksm: Export ksm_madvise()
KVM x86: Move kvm cpuid support out of svm
Add support for reset of secure guest via a new ioctl KVM_PPC_SVM_OFF.
This ioctl will be issued by QEMU during reset and includes the
the following steps:
- Release all device pages of the secure guest.
- Ask UV to terminate the guest via UV_SVM_TERMINATE ucall
- Unpin the VPA pages so that they can be migrated back to secure
side when guest becomes secure again. This is required because
pinned pages can't be migrated.
- Reinit the partition scoped page tables
After these steps, guest is ready to issue UV_ESM call once again
to switch to secure mode.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
[Implementation of uv_svm_terminate() and its call from
guest shutdown path]
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
[Unpinning of VPA pages]
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Register the new memslot with UV during plug and unregister
the memslot during unplug. In addition, release all the
device pages during unplug.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
- After the guest becomes secure, when we handle a page fault of a page
belonging to SVM in HV, send that page to UV via UV_PAGE_IN.
- Whenever a page is unmapped on the HV side, inform UV via UV_PAGE_INVAL.
- Ensure all those routines that walk the secondary page tables of
the guest don't do so in case of secure VM. For secure guest, the
active secondary page tables are in secure memory and the secondary
page tables in HV are freed when guest becomes secure.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A secure guest will share some of its pages with hypervisor (Eg. virtio
bounce buffers etc). Support sharing of pages between hypervisor and
ultravisor.
Shared page is reachable via both HV and UV side page tables. Once a
secure page is converted to shared page, the device page that represents
the secure page is unmapped from the HV side page tables.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A pseries guest can be run as secure guest on Ultravisor-enabled
POWER platforms. On such platforms, this driver will be used to manage
the movement of guest pages between the normal memory managed by
hypervisor (HV) and secure memory managed by Ultravisor (UV).
HV is informed about the guest's transition to secure mode via hcalls:
H_SVM_INIT_START: Initiate securing a VM
H_SVM_INIT_DONE: Conclude securing a VM
As part of H_SVM_INIT_START, register all existing memslots with
the UV. H_SVM_INIT_DONE call by UV informs HV that transition of
the guest to secure mode is complete.
These two states (transition to secure mode STARTED and transition
to secure mode COMPLETED) are recorded in kvm->arch.secure_guest.
Setting these states will cause the assembly code that enters the
guest to call the UV_RETURN ucall instead of trying to enter the
guest directly.
Migration of pages betwen normal and secure memory of secure
guest is implemented in H_SVM_PAGE_IN and H_SVM_PAGE_OUT hcalls.
H_SVM_PAGE_IN: Move the content of a normal page to secure page
H_SVM_PAGE_OUT: Move the content of a secure page to normal page
Private ZONE_DEVICE memory equal to the amount of secure memory
available in the platform for running secure guests is created.
Whenever a page belonging to the guest becomes secure, a page from
this private device memory is used to represent and track that secure
page on the HV side. The movement of pages between normal and secure
memory is done via migrate_vma_pages() using UV_PAGE_IN and
UV_PAGE_OUT ucalls.
In order to prevent the device private pages (that correspond to pages
of secure guest) from participating in KSM merging, H_SVM_PAGE_IN
calls ksm_madvise() under read version of mmap_sem. However
ksm_madvise() needs to be under write lock. Hence we call
kvmppc_svm_page_in with mmap_sem held for writing, and it then
downgrades to a read lock after calling ksm_madvise.
[paulus@ozlabs.org - roll in patch "KVM: PPC: Book3S HV: Take write
mmap_sem when calling ksm_madvise"]
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We failed to activate the mitigation for Spectre-RSB (Return Stack
Buffer, aka. ret2spec) on context switch, on CPUs prior to Power9
DD2.3.
That allows a process to poison the RSB (called Link Stack on Power
CPUs) and possibly misdirect speculative execution of another process.
If the victim process can be induced to execute a leak gadget then it
may be possible to extract information from the victim via a side
channel.
The fix is to correctly activate the link stack flush mitigation on
all CPUs that have any mitigation of Spectre v2 in userspace enabled.
There's a second commit which adds a link stack flush in the KVM guest
exit path. A leak via that path has not been demonstrated, but we
believe it's at least theoretically possible.
This is the fix for CVE-2019-18660.
-----BEGIN PGP SIGNATURE-----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=NQFt
-----END PGP SIGNATURE-----
Merge tag 'powerpc-spectre-rsb' of powerpc-CVE-2019-18660.bundle
Pull powerpc Spectre-RSB fixes from Michael Ellerman:
"We failed to activate the mitigation for Spectre-RSB (Return Stack
Buffer, aka. ret2spec) on context switch, on CPUs prior to Power9
DD2.3.
That allows a process to poison the RSB (called Link Stack on Power
CPUs) and possibly misdirect speculative execution of another process.
If the victim process can be induced to execute a leak gadget then it
may be possible to extract information from the victim via a side
channel.
The fix is to correctly activate the link stack flush mitigation on
all CPUs that have any mitigation of Spectre v2 in userspace enabled.
There's a second commit which adds a link stack flush in the KVM guest
exit path. A leak via that path has not been demonstrated, but we
believe it's at least theoretically possible.
This is the fix for CVE-2019-18660"
* tag 'powerpc-spectre-rsb' of /home/torvalds/Downloads/powerpc-CVE-2019-18660.bundle:
KVM: PPC: Book3S HV: Flush link stack on guest exit to host kernel
powerpc/book3s64: Fix link stack flush on context switch
- Two fixes from Greg Kurz to fix memory leak bugs in the XIVE code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEv0VLfXa2m9eKuaRpnZrqdyxjcZ8FAl3bJKwACgkQnZrqdyxj
cZ92xQgAhgnARWJwh+uazayNrwB12TJA7G25RO8CUEwWaAY/io5QeO7nQCmNZ3cf
TflQpI1dL5qFpzU7uNunHqdqyhlaD0wwkHfrN71molr5sA1uRlIyxwwkE6coZQEC
n/LiGayoxqt2Ra06H4L4SGSjb7fcCl8eYjC3xjTx9Zdf/iXVcwYprBch5kcrToLV
s0NvRvDgwcaqsxQyybTO0wRvME/qz9JFtNUgl6H4PNSt3l/yv+rM+BgjyNR3tyKu
B1G4937GqBIAV4jYmK0a/LDnNfxs9EmOjuJLKCHmVxlfbsg8wasNk3kj+mdrh2O3
ZjCdh782GyGwp/ysddOHmIhXFyQMhQ==
=9kV2
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
Second KVM PPC update for 5.5
- Two fixes from Greg Kurz to fix memory leak bugs in the XIVE code.
We need to check the host page size is big enough to accomodate the
EQ. Let's do this before taking a reference on the EQ page to avoid
a potential leak if the check fails.
Cc: stable@vger.kernel.org # v5.2
Fixes: 13ce3297c5 ("KVM: PPC: Book3S HV: XIVE: Add controls for the EQ configuration")
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The EQ page is allocated by the guest and then passed to the hypervisor
with the H_INT_SET_QUEUE_CONFIG hcall. A reference is taken on the page
before handing it over to the HW. This reference is dropped either when
the guest issues the H_INT_RESET hcall or when the KVM device is released.
But, the guest can legitimately call H_INT_SET_QUEUE_CONFIG several times,
either to reset the EQ (vCPU hot unplug) or to set a new EQ (guest reboot).
In both cases the existing EQ page reference is leaked because we simply
overwrite it in the XIVE queue structure without calling put_page().
This is especially visible when the guest memory is backed with huge pages:
start a VM up to the guest userspace, either reboot it or unplug a vCPU,
quit QEMU. The leak is observed by comparing the value of HugePages_Free in
/proc/meminfo before and after the VM is run.
Ideally we'd want the XIVE code to handle the EQ page de-allocation at the
platform level. This isn't the case right now because the various XIVE
drivers have different allocation needs. It could maybe worth introducing
hooks for this purpose instead of exposing XIVE internals to the drivers,
but this is certainly a huge work to be done later.
In the meantime, for easier backport, fix both vCPU unplug and guest reboot
leaks by introducing a wrapper around xive_native_configure_queue() that
does the necessary cleanup.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v5.2
Fixes: 13ce3297c5 ("KVM: PPC: Book3S HV: XIVE: Add controls for the EQ configuration")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Tested-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On some systems that are vulnerable to Spectre v2, it is up to
software to flush the link stack (return address stack), in order to
protect against Spectre-RSB.
When exiting from a guest we do some house keeping and then
potentially exit to C code which is several stack frames deep in the
host kernel. We will then execute a series of returns without
preceeding calls, opening up the possiblity that the guest could have
poisoned the link stack, and direct speculative execution of the host
to a gadget of some sort.
To prevent this we add a flush of the link stack on exit from a guest.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* Add capability to tell userspace whether we can single-step the guest.
* Improve the allocation of XIVE virtual processor IDs, to reduce the
risk of running out of IDs when running many VMs on POWER9.
* Rewrite interrupt synthesis code to deliver interrupts in virtual
mode when appropriate.
* Minor cleanups and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJdur0ZAAoJEJ2a6ncsY3Gf/xoH/j4wIOKcSjXFxPBAPvvR01Ld
Yt3n+ly/388uMuB4egsM/H+50CK8mpsMA02mQ40nwD4XoTFbOwhKS5wbgd4rQCoX
KtYr1Ylz+D4egw5W0c8Bu7Qdipt8TvKtSFGqDbARWg9oNiN0ZNd0zbuuzA9VpFkL
e58iwUHj1umWqPzHloqtHTyP1jakd9MMLoY5k+BpRKWSwj9ljUNi6JTGv/j8h2f/
JgKEXQ5Ug7Q3eqkMA+jx5fR5OL39rgDwhczd8WxSPz75UD5D3ijuEcmfXsJcMNHL
APggspJI6CHkjYNFAsGoPX4/MQwo0EOJMlWIgGxIoKAiHZbzCxJkYFb8Ibg59GU=
=LodM
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
KVM PPC update for 5.5
* Add capability to tell userspace whether we can single-step the guest.
* Improve the allocation of XIVE virtual processor IDs, to reduce the
risk of running out of IDs when running many VMs on POWER9.
* Rewrite interrupt synthesis code to deliver interrupts in virtual
mode when appropriate.
* Minor cleanups and improvements.
Add a new helper, kvm_put_kvm_no_destroy(), to handle putting a borrowed
reference[*] to the VM when installing a new file descriptor fails. KVM
expects the refcount to remain valid in this case, as the in-progress
ioctl() has an explicit reference to the VM. The primary motiviation
for the helper is to document that the 'kvm' pointer is still valid
after putting the borrowed reference, e.g. to document that doing
mutex(&kvm->lock) immediately after putting a ref to kvm isn't broken.
[*] When exposing a new object to userspace via a file descriptor, e.g.
a new vcpu, KVM grabs a reference to itself (the VM) prior to making
the object visible to userspace to avoid prematurely freeing the VM
in the scenario where userspace immediately closes file descriptor.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
AIL=2 mode has no known users, so is not well tested or supported.
Disallow guests from selecting this mode because it may become
deprecated in future versions of the architecture.
This policy decision is not left to QEMU because KVM support is
required for AIL=2 (when injecting interrupts).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
kvmppc_inject_interrupt does not implement LPCR[AIL]!=0 modes, which
can result in the guest receiving interrupts as if LPCR[AIL]=0
contrary to the ISA.
In practice, Linux guests cope with this deviation, but it should be
fixed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This consolidates the HV interrupt delivery logic into one place.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
reset_msr sets the MSR for interrupt injection, but it's cleaner and
more flexible to provide a single op to set both MSR and PC for the
interrupt.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Add a new attribute to both XIVE and XICS-on-XIVE KVM devices so that
userspace can tell how many interrupt servers it needs. If a VM needs
less than the current default of KVM_MAX_VCPUS (2048), we can allocate
less VPs in OPAL. Combined with a core stride (VSMT) that matches the
number of guest threads per core, this may substantially increases the
number of VMs that can run concurrently with an in-kernel XIVE device.
Since the legacy XIVE KVM device is exposed to userspace through the
XICS KVM API, a new attribute group is added to it for this purpose.
While here, fix the syntax of the existing KVM_DEV_XICS_GRP_SOURCES
in the XICS documentation.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The XIVE VP is an internal structure which allow the XIVE interrupt
controller to maintain the interrupt context state of vCPUs non
dispatched on HW threads.
When a guest is started, the XIVE KVM device allocates a block of
XIVE VPs in OPAL, enough to accommodate the highest possible vCPU
id KVM_MAX_VCPU_ID (16384) packed down to KVM_MAX_VCPUS (2048).
With a guest's core stride of 8 and a threading mode of 1 (QEMU's
default), a VM must run at least 256 vCPUs to actually need such a
range of VPs.
A POWER9 system has a limited XIVE VP space : 512k and KVM is
currently wasting this HW resource with large VP allocations,
especially since a typical VM likely runs with a lot less vCPUs.
Make the size of the VP block configurable. Add an nr_servers
field to the XIVE structure and a function to set it for this
purpose.
Split VP allocation out of the device create function. Since the
VP block isn't used before the first vCPU connects to the XIVE KVM
device, allocation is now performed by kvmppc_xive_connect_vcpu().
This gives the opportunity to set nr_servers in between:
kvmppc_xive_create() / kvmppc_xive_native_create()
.
.
kvmppc_xive_set_nr_servers()
.
.
kvmppc_xive_connect_vcpu() / kvmppc_xive_native_connect_vcpu()
The connect_vcpu() functions check that the vCPU id is below nr_servers
and if it is the first vCPU they allocate the VP block. This is protected
against a concurrent update of nr_servers by kvmppc_xive_set_nr_servers()
with the xive->lock mutex.
Also, the block is allocated once for the device lifetime: nr_servers
should stay constant otherwise connect_vcpu() could generate a boggus
VP id and likely crash OPAL. It is thus forbidden to update nr_servers
once the block is allocated.
If the VP allocation fail, return ENOSPC which seems more appropriate to
report the depletion of system wide HW resource than ENOMEM or ENXIO.
A VM using a stride of 8 and 1 thread per core with 32 vCPUs would hence
only need 256 VPs instead of 2048. If the stride is set to match the number
of threads per core, this goes further down to 32.
This will be exposed to userspace by a subsequent patch.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reduce code duplication by consolidating the checking of vCPU ids and VP
ids to a common helper used by both legacy and native XIVE KVM devices.
And explain the magic with a comment.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Print out the VP id of each connected vCPU, this allow to see:
- the VP block base in which OPAL encodes information that may be
useful when debugging
- the packed vCPU id which may differ from the raw vCPU id if the
latter is >= KVM_MAX_VCPUS (2048)
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
If we cannot allocate the XIVE VPs in OPAL, the creation of a XIVE or
XICS-on-XIVE device is aborted as expected, but we leave kvm->arch.xive
set forever since the release method isn't called in this case. Any
subsequent tentative to create a XIVE or XICS-on-XIVE for this VM will
thus always fail (DoS). This is a problem for QEMU since it destroys
and re-creates these devices when the VM is reset: the VM would be
restricted to using the much slower emulated XIVE or XICS forever.
As an alternative to adding rollback, do not assign kvm->arch.xive before
making sure the XIVE VPs are allocated in OPAL.
Cc: stable@vger.kernel.org # v5.2
Fixes: 5422e95103 ("KVM: PPC: Book3S HV: XIVE: Replace the 'destroy' method by a 'release' method")
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Given that in kvm_create_vm() there is:
kvm->mm = current->mm;
And that on every kvm_*_ioctl we have:
if (kvm->mm != current->mm)
return -EIO;
I see no reason to keep using current->mm instead of kvm->mm.
By doing so, we would reduce the use of 'global' variables on code, relying
more in the contents of kvm struct.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reduces the number of calls to get_current() in order to get the value of
current->mm by doing it once and storing the value, since it is not
supposed to change inside the same process).
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When calling the KVM_SET_GUEST_DEBUG ioctl, userspace might request
the next instruction to be single stepped via the
KVM_GUESTDBG_SINGLESTEP control bit of the kvm_guest_debug structure.
This patch adds the KVM_CAP_PPC_GUEST_DEBUG_SSTEP capability in order
to inform userspace about the state of single stepping support.
We currently don't have support for guest single stepping implemented
in Book3S HV so the capability is only present for Book3S PR and
BookE.
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
kvmhv_switch_to_host() in arch/powerpc/kvm/book3s_hv_rmhandlers.S
needs to set kvmppc_vcore->in_guest to 0 to signal secondary CPUs to
continue. This happens after resetting the PCR. Before commit
13c7bb3c57 ("powerpc/64s: Set reserved PCR bits"), r0 would always
be 0 before it was stored to kvmppc_vcore->in_guest. However because
of this change in the commit:
/* Reset PCR */
ld r0, VCORE_PCR(r5)
- cmpdi r0, 0
+ LOAD_REG_IMMEDIATE(r6, PCR_MASK)
+ cmpld r0, r6
beq 18f
- li r0, 0
- mtspr SPRN_PCR, r0
+ mtspr SPRN_PCR, r6
18:
/* Signal secondary CPUs to continue */
stb r0,VCORE_IN_GUEST(r5)
We are no longer comparing r0 against 0 and loading it with 0 if it
contains something else. Hence when we store r0 to
kvmppc_vcore->in_guest, it might not be 0. This means that secondary
CPUs will not be signalled to continue. Those CPUs get stuck and
errors like the following are logged:
KVM: CPU 1 seems to be stuck
KVM: CPU 2 seems to be stuck
KVM: CPU 3 seems to be stuck
KVM: CPU 4 seems to be stuck
KVM: CPU 5 seems to be stuck
KVM: CPU 6 seems to be stuck
KVM: CPU 7 seems to be stuck
This can be reproduced with:
$ for i in `seq 1 7` ; do chcpu -d $i ; done ;
$ taskset -c 0 qemu-system-ppc64 -smp 8,threads=8 \
-M pseries,accel=kvm,kvm-type=HV -m 1G -nographic -vga none \
-kernel vmlinux -initrd initrd.cpio.xz
Fix by making sure r0 is 0 before storing it to
kvmppc_vcore->in_guest.
Fixes: 13c7bb3c57 ("powerpc/64s: Set reserved PCR bits")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191004025317.19340-1-jniethe5@gmail.com
a nested hypervisor has always been busted on Broadwell and newer processors,
and that has finally been fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdlzTRAAoJEL/70l94x66DElcH/Rvhn5VQE/n2J+tKEXAICxQu
FqcTBJ5x2mp04aFe7xD3kWoKRJmz2lmHdw2ahFd4sqqLfGEFF/KW24ADI33vzLx/
UmT78O0Je3PX77TRnEXy+napbJny0iT6ikTAQKPbyQ151JlqlbPvatpDXXLPWQHv
jj6nKHCvMBrhV3kgaXO3cTFl8swX1hvR9lo9PcA2gRNt+HMN0heUmpfKughPoOes
JH+UNjsEr7MYlXYlIIc9o71EYH+kgPObwlLejy0ture+dvvZEJUJjZJE8H/XG5f2
ryXG9favaCOTAvaGf0R5Es+47A3crqUr6gHS0N28QKPn7x4hehIkKpA9dXQnWIw=
=1/LN
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM and x86 bugfixes of all kinds.
The most visible one is that migrating a nested hypervisor has always
been busted on Broadwell and newer processors, and that has finally
been fixed"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
KVM: x86: omit "impossible" pmu MSRs from MSR list
KVM: nVMX: Fix consistency check on injected exception error code
KVM: x86: omit absent pmu MSRs from MSR list
selftests: kvm: Fix libkvm build error
kvm: vmx: Limit guest PMCs to those supported on the host
kvm: x86, powerpc: do not allow clearing largepages debugfs entry
KVM: selftests: x86: clarify what is reported on KVM_GET_MSRS failure
KVM: VMX: Set VMENTER_L1D_FLUSH_NOT_REQUIRED if !X86_BUG_L1TF
selftests: kvm: add test for dirty logging inside nested guests
KVM: x86: fix nested guest live migration with PML
KVM: x86: assign two bits to track SPTE kinds
KVM: x86: Expose XSAVEERPTR to the guest
kvm: x86: Enumerate support for CLZERO instruction
kvm: x86: Use AMD CPUID semantics for AMD vCPUs
kvm: x86: Improve emulation of CPUID leaves 0BH and 1FH
KVM: X86: Fix userspace set invalid CR4
kvm: x86: Fix a spurious -E2BIG in __do_cpuid_func
KVM: LAPIC: Loosen filter for adaptive tuning of lapic_timer_advance_ns
KVM: arm/arm64: vgic: Use the appropriate TRACE_INCLUDE_PATH
arm64: KVM: Kill hyp_alternate_select()
...
The largepages debugfs entry is incremented/decremented as shadow
pages are created or destroyed. Clearing it will result in an
underflow, which is harmless to KVM but ugly (and could be
misinterpreted by tools that use debugfs information), so make
this particular statistic read-only.
Cc: kvm-ppc@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On POWER9, under some circumstances, a broadcast TLB invalidation will
fail to invalidate the ERAT cache on some threads when there are
parallel mtpidr/mtlpidr happening on other threads of the same core.
This can cause stores to continue to go to a page after it's unmapped.
The workaround is to force an ERAT flush using PID=0 or LPID=0 tlbie
flush. This additional TLB flush will cause the ERAT cache
invalidation. Since we are using PID=0 or LPID=0, we don't get
filtered out by the TLB snoop filtering logic.
We need to still follow this up with another tlbie to take care of
store vs tlbie ordering issue explained in commit:
a5d4b5891c ("powerpc/mm: Fixup tlbie vs store ordering issue on
POWER9"). The presence of ERAT cache implies we can still get new
stores and they may miss store queue marking flush.
Cc: stable@vger.kernel.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190924035254.24612-3-aneesh.kumar@linux.ibm.com
Rename the #define to indicate this is related to store vs tlbie
ordering issue. In the next patch, we will be adding another feature
flag that is used to handles ERAT flush vs tlbie ordering issue.
Fixes: a5d4b5891c ("powerpc/mm: Fixup tlbie vs store ordering issue on POWER9")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190924035254.24612-2-aneesh.kumar@linux.ibm.com
On a 2-socket Power9 system with 32 cores/128 threads (SMT4) and 1TB
of memory running the following guest configs:
guest A:
- 224GB of memory
- 56 VCPUs (sockets=1,cores=28,threads=2), where:
VCPUs 0-1 are pinned to CPUs 0-3,
VCPUs 2-3 are pinned to CPUs 4-7,
...
VCPUs 54-55 are pinned to CPUs 108-111
guest B:
- 4GB of memory
- 4 VCPUs (sockets=1,cores=4,threads=1)
with the following workloads (with KSM and THP enabled in all):
guest A:
stress --cpu 40 --io 20 --vm 20 --vm-bytes 512M
guest B:
stress --cpu 4 --io 4 --vm 4 --vm-bytes 512M
host:
stress --cpu 4 --io 4 --vm 2 --vm-bytes 256M
the below soft-lockup traces were observed after an hour or so and
persisted until the host was reset (this was found to be reliably
reproducible for this configuration, for kernels 4.15, 4.18, 5.0,
and 5.3-rc5):
[ 1253.183290] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1253.183319] rcu: 124-....: (5250 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=1941
[ 1256.287426] watchdog: BUG: soft lockup - CPU#105 stuck for 23s! [CPU 52/KVM:19709]
[ 1264.075773] watchdog: BUG: soft lockup - CPU#24 stuck for 23s! [worker:19913]
[ 1264.079769] watchdog: BUG: soft lockup - CPU#31 stuck for 23s! [worker:20331]
[ 1264.095770] watchdog: BUG: soft lockup - CPU#45 stuck for 23s! [worker:20338]
[ 1264.131773] watchdog: BUG: soft lockup - CPU#64 stuck for 23s! [avocado:19525]
[ 1280.408480] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791]
[ 1316.198012] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1316.198032] rcu: 124-....: (21003 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=8243
[ 1340.411024] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791]
[ 1379.212609] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1379.212629] rcu: 124-....: (36756 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=14714
[ 1404.413615] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791]
[ 1442.227095] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1442.227115] rcu: 124-....: (52509 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=21403
[ 1455.111787] INFO: task worker:19907 blocked for more than 120 seconds.
[ 1455.111822] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.111833] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.111884] INFO: task worker:19908 blocked for more than 120 seconds.
[ 1455.111905] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.111925] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.111966] INFO: task worker:20328 blocked for more than 120 seconds.
[ 1455.111986] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.111998] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112048] INFO: task worker:20330 blocked for more than 120 seconds.
[ 1455.112068] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.112097] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112138] INFO: task worker:20332 blocked for more than 120 seconds.
[ 1455.112159] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.112179] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112210] INFO: task worker:20333 blocked for more than 120 seconds.
[ 1455.112231] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.112242] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112282] INFO: task worker:20335 blocked for more than 120 seconds.
[ 1455.112303] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.112332] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112372] INFO: task worker:20336 blocked for more than 120 seconds.
[ 1455.112392] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
CPUs 45, 24, and 124 are stuck on spin locks, likely held by
CPUs 105 and 31.
CPUs 105 and 31 are stuck in smp_call_function_many(), waiting on
target CPU 42. For instance:
# CPU 105 registers (via xmon)
R00 = c00000000020b20c R16 = 00007d1bcd800000
R01 = c00000363eaa7970 R17 = 0000000000000001
R02 = c0000000019b3a00 R18 = 000000000000006b
R03 = 000000000000002a R19 = 00007d537d7aecf0
R04 = 000000000000002a R20 = 60000000000000e0
R05 = 000000000000002a R21 = 0801000000000080
R06 = c0002073fb0caa08 R22 = 0000000000000d60
R07 = c0000000019ddd78 R23 = 0000000000000001
R08 = 000000000000002a R24 = c00000000147a700
R09 = 0000000000000001 R25 = c0002073fb0ca908
R10 = c000008ffeb4e660 R26 = 0000000000000000
R11 = c0002073fb0ca900 R27 = c0000000019e2464
R12 = c000000000050790 R28 = c0000000000812b0
R13 = c000207fff623e00 R29 = c0002073fb0ca808
R14 = 00007d1bbee00000 R30 = c0002073fb0ca800
R15 = 00007d1bcd600000 R31 = 0000000000000800
pc = c00000000020b260 smp_call_function_many+0x3d0/0x460
cfar= c00000000020b270 smp_call_function_many+0x3e0/0x460
lr = c00000000020b20c smp_call_function_many+0x37c/0x460
msr = 900000010288b033 cr = 44024824
ctr = c000000000050790 xer = 0000000000000000 trap = 100
CPU 42 is running normally, doing VCPU work:
# CPU 42 stack trace (via xmon)
[link register ] c00800001be17188 kvmppc_book3s_radix_page_fault+0x90/0x2b0 [kvm_hv]
[c000008ed3343820] c000008ed3343850 (unreliable)
[c000008ed33438d0] c00800001be11b6c kvmppc_book3s_hv_page_fault+0x264/0xe30 [kvm_hv]
[c000008ed33439d0] c00800001be0d7b4 kvmppc_vcpu_run_hv+0x8dc/0xb50 [kvm_hv]
[c000008ed3343ae0] c00800001c10891c kvmppc_vcpu_run+0x34/0x48 [kvm]
[c000008ed3343b00] c00800001c10475c kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm]
[c000008ed3343b90] c00800001c0f5a78 kvm_vcpu_ioctl+0x470/0x7c8 [kvm]
[c000008ed3343d00] c000000000475450 do_vfs_ioctl+0xe0/0xc70
[c000008ed3343db0] c0000000004760e4 ksys_ioctl+0x104/0x120
[c000008ed3343e00] c000000000476128 sys_ioctl+0x28/0x80
[c000008ed3343e20] c00000000000b388 system_call+0x5c/0x70
--- Exception: c00 (System Call) at 00007d545cfd7694
SP (7d53ff7edf50) is in userspace
It was subsequently found that ipi_message[PPC_MSG_CALL_FUNCTION]
was set for CPU 42 by at least 1 of the CPUs waiting in
smp_call_function_many(), but somehow the corresponding
call_single_queue entries were never processed by CPU 42, causing the
callers to spin in csd_lock_wait() indefinitely.
Nick Piggin suggested something similar to the following sequence as
a possible explanation (interleaving of CALL_FUNCTION/RESCHEDULE
IPI messages seems to be most common, but any mix of CALL_FUNCTION and
!CALL_FUNCTION messages could trigger it):
CPU
X: smp_muxed_ipi_set_message():
X: smp_mb()
X: message[RESCHEDULE] = 1
X: doorbell_global_ipi(42):
X: kvmppc_set_host_ipi(42, 1)
X: ppc_msgsnd_sync()/smp_mb()
X: ppc_msgsnd() -> 42
42: doorbell_exception(): // from CPU X
42: ppc_msgsync()
105: smp_muxed_ipi_set_message():
105: smb_mb()
// STORE DEFERRED DUE TO RE-ORDERING
--105: message[CALL_FUNCTION] = 1
| 105: doorbell_global_ipi(42):
| 105: kvmppc_set_host_ipi(42, 1)
| 42: kvmppc_set_host_ipi(42, 0)
| 42: smp_ipi_demux_relaxed()
| 42: // returns to executing guest
| // RE-ORDERED STORE COMPLETES
->105: message[CALL_FUNCTION] = 1
105: ppc_msgsnd_sync()/smp_mb()
105: ppc_msgsnd() -> 42
42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored
105: // hangs waiting on 42 to process messages/call_single_queue
This can be prevented with an smp_mb() at the beginning of
kvmppc_set_host_ipi(), such that stores to message[<type>] (or other
state indicated by the host_ipi flag) are ordered vs. the store to
to host_ipi.
However, doing so might still allow for the following scenario (not
yet observed):
CPU
X: smp_muxed_ipi_set_message():
X: smp_mb()
X: message[RESCHEDULE] = 1
X: doorbell_global_ipi(42):
X: kvmppc_set_host_ipi(42, 1)
X: ppc_msgsnd_sync()/smp_mb()
X: ppc_msgsnd() -> 42
42: doorbell_exception(): // from CPU X
42: ppc_msgsync()
// STORE DEFERRED DUE TO RE-ORDERING
-- 42: kvmppc_set_host_ipi(42, 0)
| 42: smp_ipi_demux_relaxed()
| 105: smp_muxed_ipi_set_message():
| 105: smb_mb()
| 105: message[CALL_FUNCTION] = 1
| 105: doorbell_global_ipi(42):
| 105: kvmppc_set_host_ipi(42, 1)
| // RE-ORDERED STORE COMPLETES
-> 42: kvmppc_set_host_ipi(42, 0)
42: // returns to executing guest
105: ppc_msgsnd_sync()/smp_mb()
105: ppc_msgsnd() -> 42
42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored
105: // hangs waiting on 42 to process messages/call_single_queue
Fixing this scenario would require an smp_mb() *after* clearing
host_ipi flag in kvmppc_set_host_ipi() to order the store vs.
subsequent processing of IPI messages.
To handle both cases, this patch splits kvmppc_set_host_ipi() into
separate set/clear functions, where we execute smp_mb() prior to
setting host_ipi flag, and after clearing host_ipi flag. These
functions pair with each other to synchronize the sender and receiver
sides.
With that change in place the above workload ran for 20 hours without
triggering any lock-ups.
Fixes: 755563bc79 ("powerpc/powernv: Fixes for hypervisor doorbell handling") # v4.0
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190911223155.16045-1-mdroth@linux.vnet.ibm.com
Currently the reserved bits of the Processor Compatibility
Register (PCR) are cleared as per the Programming Note in Section
1.3.3 of version 3.0B of the Power ISA. This causes all new
architecture features to be made available when running on newer
processors with new architecture features added to the PCR as bits
must be set to disable a given feature.
For example to disable new features added as part of Version 2.07 of
the ISA the corresponding bit in the PCR needs to be set.
As new processor features generally require explicit kernel support
they should be disabled until such support is implemented. Therefore
kernels should set all unknown/reserved bits in the PCR such that any
new architecture features which the kernel does not currently know
about get disabled.
An update is planned to the ISA to clarify that the PCR is an
exception to the Programming Note on reserved bits in Section 1.3.3.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190917004605.22471-2-alistair@popple.id.au
- Initial support for running on a system with an Ultravisor, which is software
that runs below the hypervisor and protects guests against some attacks by
the hypervisor.
- Support for building the kernel to run as a "Secure Virtual Machine", ie. as
a guest capable of running on a system with an Ultravisor.
- Some changes to our DMA code on bare metal, to allow devices with medium
sized DMA masks (> 32 && < 59 bits) to use more than 2GB of DMA space.
- Support for firmware assisted crash dumps on bare metal (powernv).
- Two series fixing bugs in and refactoring our PCI EEH code.
- A large series refactoring our exception entry code to use gas macros, both
to make it more readable and also enable some future optimisations.
As well as many cleanups and other minor features & fixups.
Thanks to:
Adam Zerella, Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan, Aneesh
Kumar K.V, Anju T Sudhakar, Anshuman Khandual, Balbir Singh, Benjamin
Herrenschmidt, Cédric Le Goater, Christophe JAILLET, Christophe Leroy,
Christopher M. Riedl, Christoph Hellwig, Claudio Carvalho, Daniel Axtens,
David Gibson, David Hildenbrand, Desnes A. Nunes do Rosario, Ganesh Goudar,
Gautham R. Shenoy, Greg Kurz, Guerney Hunt, Gustavo Romero, Halil Pasic, Hari
Bathini, Joakim Tjernlund, Jonathan Neuschafer, Jordan Niethe, Leonardo Bras,
Lianbo Jiang, Madhavan Srinivasan, Mahesh Salgaonkar, Mahesh Salgaonkar,
Masahiro Yamada, Maxiwell S. Garcia, Michael Anderson, Nathan Chancellor,
Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Qian Cai, Ram
Pai, Ravi Bangoria, Reza Arbab, Ryan Grimm, Sam Bobroff, Santosh Sivaraj,
Segher Boessenkool, Sukadev Bhattiprolu, Thiago Bauermann, Thiago Jung
Bauermann, Thomas Gleixner, Tom Lendacky, Vasant Hegde.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAl2EtEcTHG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgPfsD/9uXyBXn3anI/H08+mk74k5gCsmMQpn
D442CD/ByogZcccp23yBTlhawtCE03hcHnCLygn0Xgd8a4YvHts/RGHUe3fPHqlG
bEyZ7jsLVz5ebNZQP7r4eGs2pSzCajwJy2N9HJ/C1ojf15rrfRxoVJtnyhE2wXpm
DL+6o2K+nUCB3gTQ1Inr3DnWzoGOOUfNTOea2u+J+yfHwGRqOBYpevwqiwy5eelK
aRjUJCqMTvrzra49MeFwjo0Nt3/Y8UNcwA+JlGdeR8bRuWhFrYmyBRiZEKPaujNO
5EAfghBBlB0KQCqvF/tRM/c0OftHqK59AMobP9T7u9oOaBXeF/FpZX/iXjzNDPsN
j9Oo2tKLTu/YVEXqBFuREGP+znANr1Wo4CFyOG8SbvYz0HFjR6XbtRJsS+0e8GWl
kqX5/ZhYz3lBnKSNe9jgWOrh/J0KCSFigBTEWJT3xsn4YE8x8kK2l9KPqAIldWEP
sKb2UjGS7v0NKq+NvShH88Q9AeQUEIjTcg/9aDDQDe6FaRQ7KiF8bUxSdwSPi+Fn
j0lnF6i+1ATWZKuCr85veVi7C5qoe/+MqalnmP7MxULyzgXLLxUgN0SzEYO6QofK
LQK/VaH2XVr5+M5YAb7K4/NX5gbM3s1bKrCiUy4EyHNvgG7gricYdbz6HgAjKpR7
oP0rHfgmVYvF1g==
=WlW+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This is a bit late, partly due to me travelling, and partly due to a
power outage knocking out some of my test systems *while* I was
travelling.
- Initial support for running on a system with an Ultravisor, which
is software that runs below the hypervisor and protects guests
against some attacks by the hypervisor.
- Support for building the kernel to run as a "Secure Virtual
Machine", ie. as a guest capable of running on a system with an
Ultravisor.
- Some changes to our DMA code on bare metal, to allow devices with
medium sized DMA masks (> 32 && < 59 bits) to use more than 2GB of
DMA space.
- Support for firmware assisted crash dumps on bare metal (powernv).
- Two series fixing bugs in and refactoring our PCI EEH code.
- A large series refactoring our exception entry code to use gas
macros, both to make it more readable and also enable some future
optimisations.
As well as many cleanups and other minor features & fixups.
Thanks to: Adam Zerella, Alexey Kardashevskiy, Alistair Popple, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman Khandual,
Balbir Singh, Benjamin Herrenschmidt, Cédric Le Goater, Christophe
JAILLET, Christophe Leroy, Christopher M. Riedl, Christoph Hellwig,
Claudio Carvalho, Daniel Axtens, David Gibson, David Hildenbrand,
Desnes A. Nunes do Rosario, Ganesh Goudar, Gautham R. Shenoy, Greg
Kurz, Guerney Hunt, Gustavo Romero, Halil Pasic, Hari Bathini, Joakim
Tjernlund, Jonathan Neuschafer, Jordan Niethe, Leonardo Bras, Lianbo
Jiang, Madhavan Srinivasan, Mahesh Salgaonkar, Mahesh Salgaonkar,
Masahiro Yamada, Maxiwell S. Garcia, Michael Anderson, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Qian Cai, Ram Pai, Ravi Bangoria, Reza Arbab, Ryan Grimm,
Sam Bobroff, Santosh Sivaraj, Segher Boessenkool, Sukadev Bhattiprolu,
Thiago Bauermann, Thiago Jung Bauermann, Thomas Gleixner, Tom
Lendacky, Vasant Hegde"
* tag 'powerpc-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (264 commits)
powerpc/mm/mce: Keep irqs disabled during lockless page table walk
powerpc: Use ftrace_graph_ret_addr() when unwinding
powerpc/ftrace: Enable HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
ftrace: Look up the address of return_to_handler() using helpers
powerpc: dump kernel log before carrying out fadump or kdump
docs: powerpc: Add missing documentation reference
powerpc/xmon: Fix output of XIVE IPI
powerpc/xmon: Improve output of XIVE interrupts
powerpc/mm/radix: remove useless kernel messages
powerpc/fadump: support holes in kernel boot memory area
powerpc/fadump: remove RMA_START and RMA_END macros
powerpc/fadump: update documentation about option to release opalcore
powerpc/fadump: consider f/w load area
powerpc/opalcore: provide an option to invalidate /sys/firmware/opal/core file
powerpc/opalcore: export /sys/firmware/opal/core for analysing opal crashes
powerpc/fadump: update documentation about CONFIG_PRESERVE_FA_DUMP
powerpc/fadump: add support to preserve crash data on FADUMP disabled kernel
powerpc/fadump: improve how crashed kernel's memory is reserved
powerpc/fadump: consider reserved ranges while releasing memory
powerpc/fadump: make crash memory ranges array allocation generic
...
* ARM: ITS translation cache; support for 512 vCPUs, various cleanups
and bugfixes
* PPC: various minor fixes and preparation
* x86: bugfixes all over the place (posted interrupts, SVM, emulation
corner cases, blocked INIT), some IPI optimizations
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdf7fdAAoJEL/70l94x66DJzkIAKDcuWXJB4Qtoto6yUvPiHZm
LYkY/Dn1zulb/DhzrBoXFey/jZXwl9kxMYkVTefnrAl0fRwFGX+G1UYnQrtAL6Gr
ifdTYdy3kZhXCnnp99QAantWDswJHo1THwbmHrlmkxS4MdisEaTHwgjaHrDRZ4/d
FAEwW2isSonP3YJfTtsKFFjL9k2D4iMnwZ/R2B7UOaWvgnerZ1GLmOkilvnzGGEV
IQ89IIkWlkKd4SKgq8RkDKlfW5JrLrSdTK2Uf0DvAxV+J0EFkEaR+WlLsqumra0z
Eg3KwNScfQj0DyT0TzurcOxObcQPoMNSFYXLRbUu1+i0CGgm90XpF1IosiuihgU=
=w6I3
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"s390:
- ioctl hardening
- selftests
ARM:
- ITS translation cache
- support for 512 vCPUs
- various cleanups and bugfixes
PPC:
- various minor fixes and preparation
x86:
- bugfixes all over the place (posted interrupts, SVM, emulation
corner cases, blocked INIT)
- some IPI optimizations"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (75 commits)
KVM: X86: Use IPI shorthands in kvm guest when support
KVM: x86: Fix INIT signal handling in various CPU states
KVM: VMX: Introduce exit reason for receiving INIT signal on guest-mode
KVM: VMX: Stop the preemption timer during vCPU reset
KVM: LAPIC: Micro optimize IPI latency
kvm: Nested KVM MMUs need PAE root too
KVM: x86: set ctxt->have_exception in x86_decode_insn()
KVM: x86: always stop emulation on page fault
KVM: nVMX: trace nested VM-Enter failures detected by H/W
KVM: nVMX: add tracepoint for failed nested VM-Enter
x86: KVM: svm: Fix a check in nested_svm_vmrun()
KVM: x86: Return to userspace with internal error on unexpected exit reason
KVM: x86: Add kvm_emulate_{rd,wr}msr() to consolidate VXM/SVM code
KVM: x86: Refactor up kvm_{g,s}et_msr() to simplify callers
doc: kvm: Fix return description of KVM_SET_MSRS
KVM: X86: Tune PLE Window tracepoint
KVM: VMX: Change ple_window type to unsigned int
KVM: X86: Remove tailing newline for tracepoints
KVM: X86: Trace vcpu_id for vmexit
KVM: x86: Manually calculate reserved bits when loading PDPTRS
...
- Some prep for extending the uses of the rmap array
- Various minor fixes
- Commits from the powerpc topic/ppc-kvm branch, which fix a problem
with interrupts arriving after free_irq, causing host hangs and crashes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJdZwd7AAoJEJ2a6ncsY3GffDQH/2q+c2z56ZO2lzfk4Hy9piWn
Z9PR9n72Z6TiMyVCl7CtLCyI+lRy3QVZnol14ugQNX4aFJiiwDGRHJF0wNxjeok4
4DAIqBc60qD2dkp1LwtUM1YsLsr/n3tdrGU1b0VrHGoGTVhJDpbjhJsblXZ1ujGr
KxQ1Uf4XsW5T7kovHuzj+FFlbB5nbEX5cBIU68maBGZSCl355wCOW35rKVITTIIv
+VKkO2aNbk6bRmZmOi2v1D65eQa2+TKe/o48TneJv1WhL4h4hDyHdmVeWRNoAI6C
ve8mwCAVs7IITjCJ1qcGnI8NzVxMlXgwVir7sQ1aslRLZfeRAm5FOIPNEz1ADXs=
=3oLd
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
PPC KVM update for 5.4
- Some prep for extending the uses of the rmap array
- Various minor fixes
- Commits from the powerpc topic/ppc-kvm branch, which fix a problem
with interrupts arriving after free_irq, causing host hangs and crashes.
Introduce two options to control the use of the tlbie instruction. A
boot time option which completely disables the kernel using the
instruction, this is currently incompatible with HASH MMU, KVM, and
coherent accelerators.
And a debugfs option can be switched at runtime and avoids using tlbie
for invalidating CPU TLBs for normal process and kernel address
mappings. Coherent accelerators are still managed with tlbie, as will
KVM partition scope translations.
Cross-CPU TLB flushing is implemented with IPIs and tlbiel. This is a
basic implementation which does not attempt to make any optimisation
beyond the tlbie implementation.
This is useful for performance testing among other things. For example
in certain situations on large systems, using IPIs may be faster than
tlbie as they can be directed rather than broadcast. Later we may also
take advantage of the IPIs to do more interesting things such as trim
the mm cpumask more aggressively.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190902152931.17840-7-npiggin@gmail.com
There should be no functional changes.
- Use calls to existing radix_tlb.c functions in flush_partition.
- Rename radix__flush_tlb_lpid to radix__flush_all_lpid and similar,
because they flush everything, matching flush_all_mm rather than
flush_tlb_mm for the lpid.
- Remove some unused radix_tlb.c flush primitives.
Signed-off: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190902152931.17840-3-npiggin@gmail.com
When an SVM makes an hypercall or incurs some other exception, the
Ultravisor usually forwards (a.k.a. reflects) the exceptions to the
Hypervisor. After processing the exception, Hypervisor uses the
UV_RETURN ultracall to return control back to the SVM.
The expected register state on entry to this ultracall is:
* Non-volatile registers are restored to their original values.
* If returning from an hypercall, register R0 contains the return value
(unlike other ultracalls) and, registers R4 through R12 contain any
output values of the hypercall.
* R3 contains the ultracall number, i.e UV_RETURN.
* If returning with a synthesized interrupt, R2 contains the
synthesized interrupt number.
Thanks to input from Paul Mackerras, Ram Pai and Mike Anderson.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Claudio Carvalho <cclaudio@linux.ibm.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190822034838.27876-8-cclaudio@linux.ibm.com
Invalidating a TCE cache entry for each updated TCE is quite expensive.
This makes use of the new iommu_table_ops::xchg_no_kill()/tce_kill()
callbacks to bring down the time spent in mapping a huge guest DMA window;
roughly 20s to 10s for each guest's 100GB of DMA space.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190829085252.72370-3-aik@ozlabs.ru
H_PUT_TCE_INDIRECT handlers receive a page with up to 512 TCEs from
a guest. Although we verify correctness of TCEs before we do anything
with the existing tables, there is a small window when a check in
kvmppc_tce_validate might pass and right after that the guest alters
the page with TCEs which can cause early exit from the handler and
leave srcu_read_lock(&vcpu->kvm->srcu) (virtual mode) or lock_rmap(rmap)
(real mode) locked.
This fixes the bug by jumping to the common exit code with an appropriate
unlock.
Fixes: 121f80ba68 ("KVM: PPC: VFIO: Add in-kernel acceleration for VFIO")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190826045520.92153-1-aik@ozlabs.ru
On POWER9, when userspace reads the value of the DPDES register on a
vCPU, it is possible for 0 to be returned although there is a doorbell
interrupt pending for the vCPU. This can lead to a doorbell interrupt
being lost across migration. If the guest kernel uses doorbell
interrupts for IPIs, then it could malfunction because of the lost
interrupt.
This happens because a newly-generated doorbell interrupt is signalled
by setting vcpu->arch.doorbell_request to 1; the DPDES value in
vcpu->arch.vcore->dpdes is not updated, because it can only be updated
when holding the vcpu mutex, in order to avoid races.
To fix this, we OR in vcpu->arch.doorbell_request when reading the
DPDES value.
Cc: stable@vger.kernel.org # v4.13+
Fixes: 579006944e ("KVM: PPC: Book3S HV: Virtualize doorbell facility on POWER9")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
When we are running multiple vcores on the same physical core, they
could be from different VMs and so it is possible that one of the
VMs could have its arch.mmu_ready flag cleared (for example by a
concurrent HPT resize) when we go to run it on a physical core.
We currently check the arch.mmu_ready flag for the primary vcore
but not the flags for the other vcores that will be run alongside
it. This adds that check, and also a check when we select the
secondary vcores from the preempted vcores list.
Cc: stable@vger.kernel.org # v4.14+
Fixes: 38c53af853 ("KVM: PPC: Book3S HV: Fix exclusion between HPT resizing and other HPT updates")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
There are some POWER9 machines where the OPAL firmware does not support
the OPAL_XIVE_GET_QUEUE_STATE and OPAL_XIVE_SET_QUEUE_STATE calls.
The impact of this is that a guest using XIVE natively will not be able
to be migrated successfully. On the source side, the get_attr operation
on the KVM native device for the KVM_DEV_XIVE_GRP_EQ_CONFIG attribute
will fail; on the destination side, the set_attr operation for the same
attribute will fail.
This adds tests for the existence of the OPAL get/set queue state
functions, and if they are not supported, the XIVE-native KVM device
is not created and the KVM_CAP_PPC_IRQ_XIVE capability returns false.
Userspace can then either provide a software emulation of XIVE, or
else tell the guest that it does not have a XIVE controller available
to it.
Cc: stable@vger.kernel.org # v5.2+
Fixes: 3fab2d1058 ("KVM: PPC: Book3S HV: XIVE: Activate XIVE exploitation mode")
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
H_PUT_TCE_INDIRECT handlers receive a page with up to 512 TCEs from
a guest. Although we verify correctness of TCEs before we do anything
with the existing tables, there is a small window when a check in
kvmppc_tce_validate might pass and right after that the guest alters
the page of TCEs, causing an early exit from the handler and leaving
srcu_read_lock(&vcpu->kvm->srcu) (virtual mode) or lock_rmap(rmap)
(real mode) locked.
This fixes the bug by jumping to the common exit code with an appropriate
unlock.
Cc: stable@vger.kernel.org # v4.11+
Fixes: 121f80ba68 ("KVM: PPC: VFIO: Add in-kernel acceleration for VFIO")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The rmap array in the guest memslot is an array of size number of guest
pages, allocated at memslot creation time. Each rmap entry in this array
is used to store information about the guest page to which it
corresponds. For example for a hpt guest it is used to store a lock bit,
rc bits, a present bit and the index of a hpt entry in the guest hpt
which maps this page. For a radix guest which is running nested guests
it is used to store a pointer to a linked list of nested rmap entries
which store the nested guest physical address which maps this guest
address and for which there is a pte in the shadow page table.
As there are currently two uses for the rmap array, and the potential
for this to expand to more in the future, define a type field (being the
top 8 bits of the rmap entry) to be used to define the type of the rmap
entry which is currently present and define two values for this field
for the two current uses of the rmap array.
Since the nested case uses the rmap entry to store a pointer, define
this type as having the two high bits set as is expected for a pointer.
Define the hpt entry type as having bit 56 set (bit 7 IBM bit ordering).
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Fix the error below triggered by `-Wimplicit-fallthrough`, by tagging
it as an expected fall-through.
arch/powerpc/kvm/book3s_32_mmu.c: In function ‘kvmppc_mmu_book3s_32_xlate_pte’:
arch/powerpc/kvm/book3s_32_mmu.c:241:21: error: this statement may fall through [-Werror=implicit-fallthrough=]
pte->may_write = true;
~~~~~~~~~~~~~~~^~~~~~
arch/powerpc/kvm/book3s_32_mmu.c:242:5: note: here
case 3:
^~~~
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Alistair Popple
Aneesh Kumar K.V
Paul Mackerras
Laurent Dufour
Qian Cai
Tianjia Zhang
Chen Zhou
Michael Ellerman
Ravi Bangoria
Jordan Niethe
David Matlack
Davidlohr Bueso
Paolo Bonzini
Christophe Leroy
Cédric Le Goater
Peter Xu
Emanuele Giuseppe Esposito
Linus Torvalds
Anshuman Khandual
Jason Wang
Nicholas Piggin
Sean Christopherson
Christoph Hellwig
Fabiano Rosas
Greg Kurz
Joe Perches
Michael Roth
Gustavo Romero
Greg Kroah-Hartman
David Michael
Bharata B Rao
Sukadev Bhattiprolu
Sukadev Bhattiprolu
Leonardo Bras
zhengbin
Marcus Comstedt
Alexey Kardashevskiy
Radim Krčmář
Suraj Jitindar Singh
Paul Menzel