* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86, fpu: fix CONFIG_PREEMPT=y corruption of application's FPU stack
suspend-vs-iommu: prevent suspend if we could not resume
x86: section mismatch fix
x86: fix Xorg crash with xf86MapVidMem error
x86: fix pointer type warning in arch/x86/mm/init_64.c:early_memtest
x86: fix bad pmd ffff810000207xxx(9090909090909090)
x86: ioremap fix failing nesting check
x86: fix broken math-emu with lazy allocation of fpu area
x86: enable preemption in delay
x86: disable preemption in native_smp_prepare_cpus
x86: fix APIC warning on 32bit v2
Jürgen Mell reported an FPU state corruption bug under CONFIG_PREEMPT,
and bisected it to commit v2.6.19-1363-gacc2076, "i386: add sleazy FPU
optimization".
Add tsk_used_math() checks to prevent calling math_state_restore()
which can sleep in the case of !tsk_used_math(). This prevents
making a blocking call in __switch_to().
Apparently "fpu_counter > 5" check is not enough, as in some signal handling
and fork/exec scenarios, fpu_counter > 5 and !tsk_used_math() is possible.
It's a side effect though. This is the failing scenario:
process 'A' in save_i387_ia32() just after clear_used_math()
Got an interrupt and pre-empted out.
At the next context switch to process 'A' again, kernel tries to restore
the math state proactively and sees a fpu_counter > 0 and !tsk_used_math()
This results in init_fpu() during the __switch_to()'s math_state_restore()
And resulting in fpu corruption which will be saved/restored
(save_i387_fxsave and restore_i387_fxsave) during the remaining
part of the signal handling after the context switch.
Bisected-by: Jürgen Mell <j.mell@t-online.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Jürgen Mell <j.mell@t-online.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
iommu/gart support misses suspend/resume code, which can do bad stuff,
including memory corruption on resume. Prevent system suspend in case we
would be unable to resume.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Tested-by: Patrick <ragamuffin@datacomm.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this:
WARNING: vmlinux.o(.text+0x114bb): Section mismatch in reference from
the function nopat() to the function .cpuinit.text:pat_disable()
The function nopat() references
the function __cpuinit pat_disable().
This is often because nopat lacks a __cpuinit
annotation or the annotation of pat_disable is wrong.
Reported-by: "Fabio Comolli" <fabio.comolli@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Clarify the usage of mtrr_lookup() in PAT code, and to make PAT code
resilient to mtrr lookup problems.
Specifically, pat_x_mtrr_type() is restructured to highlight, under what
conditions we look for mtrr hint. pat_x_mtrr_type() uses a default type
when there are any errors in mtrr lookup (still maintaining the pat
consistency). And, reserve_memtype() highlights its usage ot mtrr_lookup
for request type of '-1' and also defaults in a sane way on any mtrr
lookup failure.
pat.c looks at mtrr type of a range to get a hint on what mapping type
to request when user/API: (1) hasn't specified any type (/dev/mem
mapping) and we do not want to take performance hit by always mapping
UC_MINUS. This will be the case for /dev/mem mappings used to map BIOS
area or ACPI region which are WB'able. In this case, as long as MTRR is
not WB, PAT will request UC_MINUS for such mappings.
(2) user/API requests WB mapping while in reality MTRR may have UC or
WC. In this case, PAT can map as WB (without checking MTRR) and still
effective type will be UC or WC. But, a subsequent request to map same
region as UC or WC may fail, as the region will get trackked as WB in
PAT list. Looking at MTRR hint helps us to track based on effective type
rather than what user requested. Again, here mtrr_lookup is only used as
hint and we fallback to WB mapping (as requested by user) as default.
In both cases, after using the mtrr hint, we still go through the
memtype list to make sure there are no inconsistencies among multiple
users.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Rufus & Azrael <rufus-azrael@numericable.fr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Changed the call to find_e820_area_size to pass u64 instead of unsigned long.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
OGAWA Hirofumi and Fede have reported rare pmd_ERROR messages:
mm/memory.c:127: bad pmd ffff810000207xxx(9090909090909090).
Initialization's cleanup_highmap was leaving alignment filler
behind in the pmd for MODULES_VADDR: when vmalloc's guard page
would occupy a new page table, it's not allocated, and then
module unload's vfree hits the bad 9090 pmd entry left over.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mika Kukkonen noticed that the nesting check in early_iounmap() is not
actually done.
Reported-by: Mika Kukkonen <mikukkon@srv1-m700-lanp.koti>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: torvalds@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: mikukkon@iki.fi
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the math emulation that got broken with the recent lazy allocation of FPU
area. init_fpu() need to be added for the math-emulation path aswell
for the FPU area allocation.
math emulation enabled kernel booted fine with this, in the presence
of "no387 nofxsr" boot param.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: hpa@zytor.com
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The RT team has been searching for a nasty latency. This latency shows
up out of the blue and has been seen to be as big as 5ms!
Using ftrace I found the cause of the latency.
pcscd-2995 3dNh1 52360300us : irq_exit (smp_apic_timer_interrupt)
pcscd-2995 3dN.2 52360301us : idle_cpu (irq_exit)
pcscd-2995 3dN.2 52360301us : rcu_irq_exit (irq_exit)
pcscd-2995 3dN.1 52360771us : smp_apic_timer_interrupt (apic_timer_interrupt
)
pcscd-2995 3dN.1 52360771us : exit_idle (smp_apic_timer_interrupt)
Here's an example of a 400 us latency. pcscd took a timer interrupt and
returned with "need resched" enabled, but did not reschedule until after
the next interrupt came in at 52360771us 400us later!
At first I thought we somehow missed a preemption check in entry.S. But
I also noticed that this always seemed to happen during a __delay call.
pcscd-2995 3dN.2 52360836us : rcu_irq_exit (irq_exit)
pcscd-2995 3.N.. 52361265us : preempt_schedule (__delay)
Looking at the x86 delay, I found my problem.
In git commit 35d5d08a08, Andrew Morton
placed preempt_disable around the entire delay due to TSC's not working
nicely on SMP. Unfortunately for those that care about latencies this
is devastating! Especially when we have callers to mdelay(8).
Here I enable preemption during the loop and account for anytime the task
migrates to a new CPU. The delay asked for may be extended a bit by
the migration, but delay only guarantees that it will delay for that minimum
time. Delaying longer should not be an issue.
[
Thanks to Thomas Gleixner for spotting that cpu wasn't updated,
and to place the rep_nop between preempt_enabled/disable.
]
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: akpm@osdl.org
Cc: Clark Williams <clark.williams@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Luis Claudio R. Goncalves" <lclaudio@uudg.org>
Cc: Gregory Haskins <ghaskins@novell.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi-suse@firstfloor.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
for http://bugzilla.kernel.org/show_bug.cgi?id=10613
BIOS bug, APIC version is 0 for CPU#0! fixing up to 0x10. (tell your hw vendor)
v2: fix 64 bit compilation
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
RSK7203 is supportable through the generic machvec, so we add a defconfig
for those bits. This gets updated with more complete board support later.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently, fsl_i2c_of_init() uses the order of the I2C adapter nodes in the
device tree to enumerate the I2C adapters. Instead, let's check for the
cell-index property and use it if it exists.
This is handy for device drivers that need to identify the I2C adapters by
specific numbers. The Freescale MPC8610 ASoC V2 sound drivers are an example.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
8250 Serial Driver: revert extra IRQ flag definition patch
Blackfin arch: update anomaly headers from toolchain trunk
Blackfin arch: Remove bad and usless code
Blackfin arch: Fix bug - set corret SSEL and IRQ to enable AD7877 on BF527
Blackfin arch: Fix typo. it should be _outsw_8
Blackfin arch: Cleanup no functional changes
On machines with more than one exception level any system register that
might be modified by the "normal" exception level needs to be saved and
restored on taking a higher level exception. We already are saving
and restoring ESR and DEAR.
For critical level add SRR0/1.
For debug level add CSRR0/1 and SRR0/1.
For machine check level add DSRR0/1, CSRR0/1, and SRR0/1.
On FSL Book-E parts we always save/restore the MAS registers for critical,
debug, and machine check level exceptions. On 44x we always save/restore
the MMUCR.
Additionally, we save and restore the ksp_limit since we have to adjust it
for each exception level.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
* Cleanup the code a bit my allocating an INT_FRAME on our exception
stack there by make references go from GPR11-INT_FRAME_SIZE(r8) to
just GPR11(r8)
* simplify {lvl}_transfer_to_handler code by moving the copying of the
temp registers we use if we come from user space into the PROLOG
* If the exception came from kernel mode copy thread_info flags,
preempt, and task pointer from the process thread_info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
For the additonal exception levels (critical, debug, machine check) on
40x/book-e we were using "static" allocations of the stack in the
associated head.S.
Move to a runtime allocation to make the code a bit easier to read as
we mimic how we handle IRQ stacks. Its also a bit easier to setup the
stack with a "dummy" thread_info in C code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Added next-level-cache to the L1 and a reference to the new L2 label.
This is per the ePAPR 0.94 spec. Since we are't really dependent on this
today we aren't supporting the "legacy" l2-cache phandle that is specified
in the PPC v2.1 OF Binding spec.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed clock-frequency, big-endian, and built-in props as they aren't
specified anywhere. Also added compatible = "chrp,open-pic" in the
places it was missing.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.
http://www.analogue-micro.com/ASP8347.html
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The i2c_devices[] array in fsl_soc.c lists all the I2C nodes that are supported
on Freescale boards. Add an entry for the Cirrus Logic CS4270 so that a
new-style CS4270 driver will work.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update of_find_i2c_driver in fsl_soc.c to display a warning message if an
I2C node in the device tree isn't found in the i2c_devices[] array.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes few cosmetic issues, also removes unused function,
makes some functions static and reduces #ifdef count.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enabled MSI on 8544ds and 8572ds board.
So far only one MSI interrupt can generate on 8544 board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enable the MSI on 8610hpcd board.
Through the msi-available-ranges property, All the 256
msi interrupts can be tested on this board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This MSI driver can be used on 83xx/85xx/86xx board.
In this driver, virtual interrupt host and chip were
setup. There are 256 MSI interrupts in this host, Every 32
MSI interrupts cascaded to one IPIC/MPIC interrupt.
The chip was treated as edge sensitive and some necessary
functions were setup for this chip.
Before using the MSI interrupt, PCI/PCIE device need to
ask for a MSI interrupt in the 256 MSI interrupts. A 256bit
bitmap show which MSI interrupt was used, reserve bit in
the bitmap can be used to force the device use some designate
MSI interrupt in the 256 MSI interrupts. Sometimes this is useful
for testing the all the MSI interrupts. The msi-available-ranges
property in the dts file was used for this purpose.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Work around:
arch/arm/mach-pxa/tosa.c: In function `tosa_poweroff':
arch/arm/mach-pxa/tosa.c:470: error: `GPIO_OUT' undeclared (first use in this function)
arch/arm/mach-pxa/tosa.c:470: error: (Each undeclared identifier is reported only once
arch/arm/mach-pxa/tosa.c:470: error: for each function it appears in.)
The proper fix exists in the PXA branch of my kernel git tree, which
will be pushed during the next merge window.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the IORESOURCE_IRQ_HIGHEDGE to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the IORESOURCE_IRQ_HIGHEDGE to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
4k stacks on nommu ends up blowing up with all sorts of interesting
slab corruption. Disable this by default unless BROKEN is also
enabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following build error caused by
commit a1dc4b59fa
(sh: intc_sh5 depends on cayman board for IRQ priority table.):
<-- snip -->
...
CC arch/sh/kernel/cpu/irq/intc-sh5.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c: In function 'plat_irq_setup':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c:257: error: expected declaration or statement at end of input
make[4]: *** [arch/sh/kernel/cpu/irq/intc-sh5.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
AD7877 use SSEL_2 (P9.9) and IRQ_PF8 (P9.14) on BF527
- populating JP3 to enable STAMP
- disable SW11.2 to disconnect SSEL_2/PF12 from Rotary NAND
- disable SW18.1 to disconnect SSEL_2 from MAX1233 touchscreen chip
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The node for DMA2 in the MPC8610 HPCD device tree has the wrong compatible
properties. This breaks the DMA driver and the sound driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently ext4 and fuse fail to link if modular:
ERROR: "copy_page" [fs/fuse/fuse.ko] undefined!
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
make[3]: *** [__modpost] Error 1
make[2]: *** [modules] Error 2
make[1]: *** [sub-make] Error 2
While arch ppc exists it may as well compile, so this exports those
symbols (which are already exported in arch/powerpc).
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: notify on empty
virtio: force callback on empty.
virtio_blk: fix endianess annotations
virtio_config: fix len calculation of config elements
virtio_net: another race with virtio_net and enable_cb
virtio: An entropy device, as suggested by hpa.
virtio_blk: allow read-only disks
lguest: fix ugly <NULL> in /proc/interrupts
virtio: set device index in common code.
virtio: virtio_pci should not set bus_id.
virtio: bus_id for devices should contain 'virtio'
Fix crash in virtio_blk during modprobe ; rmmod ; modprobe
lguest: use ioremap_cache, not ioremap
The correct instruction format of idte is "idte r1,r3,r2" with
r1 at bit 24, r3 at bit 16 and r2 at bit 28.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert show_mem() so its nearly the same as on x86/powerpc.
Gives us proper locking and we get also rid of the only use of max_mapnr.
Also the number of pages was contained in an int which might not be
sufficient not too far in the future.
Cc: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use get_online_cpus() to prevent cpu hotplug in situations where
for_each_online_cpu() is called.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This fixes the last remaining section mismatch warnings in s390
architecture code. It reveals also a real bug introduced by... me
with git commit 2069e978d5
("[S390] sparsemem vmemmap: initialize memmap.")
Calling the generic vmemmap_alloc_block() function to get initialized
memory is a nice idea, however that function is __meminit annotated
and therefore the function might be gone if we try to call it later.
This can happen if a DCSS segment gets added.
So basically revert the patch and clear the memmap explicitly to fix
the original bug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On s390 make allnoconfig fails with the following build error:
arch/s390/mm/init.c: In function 'show_mem':
arch/s390/mm/init.c:55: error: implicit declaration of function 'pfn_valid'
make[1]: *** [arch/s390/mm/init.o] Error 1
make: *** [arch/s390/mm] Error 2
This problem can by fixed ensuring that ARCH_SELECT_MEMORY_MODEL
is always turned on.
Signed-off-by: Hans-Joachim Picht <hans@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With the recent DCR code rework, we get a compiler warning about
find_dcr_parent being defined but not used. This fixes it by only defining
the function if CONFIG_PPC_DCR_MMIO is set.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* Switched from 64M NOR/64M NAND to 4M NOR/256M NAND.
* Full DTM support including critical temperature.
* Added POST information.
* Removed LED function, moved to new LED driver.
* Moved ad7414 to new style I2C initialization.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This fixes the PCI node in the Rainier to match the spec from AMCC. A
similar fix was done for 440EPx, which shares the same values as 440GRx.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
At the moment we have a mixture of left-over version 0 and new-format
version 1 files in arch/powerpc/boot/dts. This is potentially
confusing to people new to the dts format attempting to figure it out.
So, this patch converts all the as-yet unconverted dts v0 files and
converts them to v1. They're mechanically-converted, and not hand
tweaked so in some cases they're not 100% in keeping with usual v1
style, but the convertor program does have some heuristics so the
discrepancies aren't too bad.
I have checked that this patch produces no changes to the resulting
dtb binaries.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Previously, DCR support was configured at compile time to either use
MMIO or native dcr instructions. Although this works for most
platforms, it fails on FPGA platforms:
1) Systems may include more than one DCR bus.
2) Systems may be native DCR capable and still use memory mapped DCR interface.
This patch provides runtime support based on the device trees for the
case where CONFIG_PPC_DCR_MMIO and CONFIG_PPC_DCR_NATIVE are both
selected. Previously, this was a poorly defined configuration, which
happened to provide NATIVE support. The runtime selection is made
based on the dcr-controller having a 'dcr-access-method' attribute
in the device tree. If only one of the above options is selected,
then the code uses #defines to select only the used code in order to
avoid introducing overhead in existing usage.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Problem: An application violating the architectural rules regarding
operation dependencies and having specific Register Stack Engine (RSE)
state at the time of the violation, may result in an illegal operation
fault and invalid RSE state. Such faults may initiate a cascade of
repeated illegal operation faults within OS interruption handlers.
The specific behavior is OS dependent.
Implication: An application causing an illegal operation fault with
specific RSE state may result in a series of illegal operation faults
and an eventual OS stack overflow condition.
Workaround: OS interruption handlers that switch to kernel backing
store implement a check for invalid RSE state to avoid the series
of illegal operation faults.
The core of the workaround is the RSE_WORKAROUND code sequence
inserted into each invocation of the SAVE_MIN_WITH_COVER and
SAVE_MIN_WITH_COVER_R19 macros. This sequence includes hard-coded
constants that depend on the number of stacked physical registers
being 96. The rest of this patch consists of code to disable this
workaround should this not be the case (with the presumption that
if a future Itanium processor increases the number of registers, it
would also remove the need for this patch).
Move the start of the RBS up to a mod32 boundary to avoid some
corner cases.
The dispatch_illegal_op_fault code outgrew the spot it was
squatting in when built with this patch and CONFIG_VIRT_CPU_ACCOUNTING=y
Move it out to the end of the ivt.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Move the AP7 cpufreq init to late_initcall() so that we don't try to
bring up cpufreq until the governor is ready. x86 also uses
late_initcall() for this.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.26:
sh: Drop broken URAM support on SH7723.
sh: update Migo-R defconfig
sh: use sm501 8250 mfd support on r2d boards
sh: add probe support for new sh7723 cut
sh: fix VPU interrupt vector for sh7723
sh: fix USBF resource for sh7722
Just provide reasonable defaults for the new stuff. Tickless and
hrtimers are turned on for all boards except ATSTK1004.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This was copied over from the previous MobileR bits, which doesn't
apply to R2. The URAM block on R2 is recycled for the L2 instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
init/Kconfig contains a list of configs that are searched
for if 'make *config' are used with no .config present.
Extend this list to look at the config identified by
ARCH_DEFCONFIG.
With this change we now try the defconfig targets last.
This fixes a regression reported
by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86: prevent PGE flush from interruption/preemption
x86: use explicit copy in vdso_gettimeofday()
namespacecheck: automated fixes
x86/xen: fix arbitrary_virt_to_machine()
x86: don't read maxlvt before checking if APIC is mapped
x86: disable TSC for sched_clock() when calibration failed
x86: distangle user disabled TSC from unstable
x86: fix setup of cyc2ns in tsc_64.c
Fix the following build error:
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] iSeries: Remove unused mail address
[POWERPC] mpic: Fix use of uninitialized variable
[POWERPC] Add kernstart_addr to list of allowed symbols in prom_init
[POWERPC] Fix __set_fixmap() for STRICT_MM_TYPECHECKS
[POWERPC] PS3: Fix memory hotplug
Export the AT91 clock functions for the AT91X40. Some external code common
to all AT91 family parts relys on this, like the gpio and serial support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jeremy's gcc 3.4 seems to be unable to inline a 8 byte memcpy. But the
vdso doesn't support external references. Copy the structure members
of struct timezone explicitely instead.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While I realize that the function isn't currently being used, I still
think an obvious mistake like this should be corrected.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A check for unmapped apic was added before reading maxlvt but the early
read of maxlvt wasn't removed.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
When the TSC calibration fails then TSC is still used in
sched_clock(). Disable it completely in that case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
tsc_enabled is set to 0 from the command line switch "notsc" and from
the mark_tsc_unstable code. Seperate those functionalities and replace
tsc_enable with tsc_disable. This makes also the native_sched_clock()
decision when to use TSC understandable.
Preparatory patch to solve the sched_clock() issue on 32 bit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the TSC is calibrated against the PIT due to the nonavailability
of PMTIMER/HPET or due to SMI interference then the setup of the per
CPU cyc2ns variables is skipped. This is unlikely to happen but it
would definitely render sched_clock() unusable.
This was introduced with commit 53d517cdba
x86: scale cyc_2_nsec according to CPU frequency
Update the per CPU cyc2ns variables in all exit pathes of tsc_calibrate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Compiling ppc64_defconfig with gcc 4.3 gives thes warnings:
arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_get_priority':
arch/powerpc/sysdev/mpic.c:1351: warning: 'is_ipi' may be used uninitialized in this function
arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_set_priority':
arch/powerpc/sysdev/mpic.c:1328: warning: 'is_ipi' may be used uninitialized in this function
It turns out that in the cases where is_ipi is uninitialized, another
variable (mpic) will be NULL and it is dereferenced. Protect against
this by returning if mpic is NULL in mpic_irq_set_priority, and removing
mpic_irq_get_priority completely as it has no in tree callers.
This has the nice side effect of making the warning go away.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since commit "85xx: Add support for relocatable kernel (and
booting at non-zero)" (37dd2badcf),
PHYSICAL_START is #defined as kernstart_addr if RELOCATABLE
and FLATMEM is enabled.
PHYSICAL_START is used in prom_init.c and so kernstart_addr
needs to be added to the list of allowed symbols that
prom_init.c can access.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
__set_fixmap() in pgtable_32.c currently fails to compile if
STRICT_MM_TYPECHECKS is defined. This fixes it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A change was made to walk_memory_resource() in commit
4b119e21d0 that added a
check of find_lmb(). Add the coresponding lmb_add()
call to ps3_mm_add_memory() so that that check will
succeed.
This fixes the condition where the PS3 boots up with
only the 128 MiB of boot memory, and doesn't see the
other 128MiB that is available.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
func_descr_t->entry is already an unsigned long. Mea culpa.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds some debugging code to the Axon MSI driver. It creates a
file per MSIC in /sys/kernel/debug/powerpc, which allows the user to
trigger a fake MSI interrupt by writing to the file.
This can be used to test some of the MSI generation path. In
particular, that the MSIC recognises a write to the MSI address,
generates an interrupt and writes the MSI packet into the ring buffer.
All the code is inside #ifdef DEBUG so it causes no harm unless it's
enabled.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some chips (like the SoCs from Freescale) report the wrong value in NIRQ
and this causes issues if its doesn't match or exceed the value of
irq_count.
Add a flag that board code can set to just use irq_count instead of
FRR[NIRQ]. Eventually we'll add a device tree property with the number
of sources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This works around bugs in older binutils' objcopy.
The placement of these sections does not really matter,
but it confused the buggy old BFD libraries.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the Migo-R defconfig to include support for KEYSC, I2C, RTC and
NAND and NOR MTD devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make use of recently added sm501 8250 uart support, commit
61711f8fd8 makes the mfd code
handle 8250 uarts so there is no longer need to do it from
the r2d board code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for sh7723 silicon with a prr value of 0x51.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a VPU vector typo for sh7723. The correct value is 0x980,
the same as for sh7722.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The USBF function on sh7722 is currently not working with the m66592_udc
driver. The driver is using platform_get_resource_byname() so my commit
a0d29798e5 broke sh7722 support.
The long term fix is to replace platform_get_resource_byname() in the
driver with platform_get_resource(), but this helps until that happens.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
arch/arm/plat-omap/clock.c:397: warning: "struct cpufreq_frequency_table" declared inside parameter list
arch/arm/plat-omap/clock.c:397: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/plat-omap/clock.c: In function `clk_init_cpufreq_table':
arch/arm/plat-omap/clock.c:402: error: structure has no member named `clk_init_cpufreq_table'
arch/arm/plat-omap/clock.c:403: error: structure has no member named `clk_init_cpufreq_table'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds
Al Viro
Suresh Siddha
Pavel Machek
Andrew Morton
Venki Pallipadi
Kevin Winchester
Hugh Dickins
Ingo Molnar
Steven Rostedt
Yinghai Lu
Alexey Dobriyan
Paul Mundt
Timur Tabi
Kumar Gala
Bryan O'Donoghue
Anton Vorontsov
Jason Jin
Russell King
Mike Rapoport
Harvey Harrison
Adrian Bunk
eric miao
Michael Hennerich
Bryan Wu
Tony Breeds
Martin Schwidefsky
Heiko Carstens
Gerald Schaefer
Hans-Joachim Picht
Rusty Russell
Josh Boyer
Sean MacLennan
David Gibson
Stephen Neuendorffer
Olof Johansson
Tony Luck
Haavard Skinnemoen
Sam Ravnborg
Greg Ungerer
Andi Kleen
Jan Beulich
Chuck Ebbert
Thomas Gleixner
Paul Mackerras
Stephen Rothwell
Michael Ellerman
Geoff Levand
Roland McGrath
Magnus Damm