This patch contains two fixes submitted by Ondrej Palkovsky:
- the 'ACK' packet is sent after the transfer of the USB packet is
completed, i.e. in the write_callback function. Because the close
function sends the 'abort' command, a parameter is added that allows
the caller of garmin_write_bulk to specify, if the 'ack' should be
propagated to the serial link or dimissed.
This fixes the problem with gpsbabel, it has sent several packets that
were acknowledged before they were sent to the GPS and GpsBabel closed
the device - thus effectively cancelled all outstanding requests in the
queue.
- removed the APP_RESP_SEEN and APP_REQ_SEEN flags and changed
them into counters. It evades USB reset of the gps on every device close.
Signed-off-by: Hermann Kneissel <hermann.kneissel@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as950) fixes a bug in the cdc-acm driver. It doesn't keep
track of which interface (control or data) the sysfs attributes get
registered for, and as a result, during disconnect it will sometimes
attempt to remove the attributes from the wrong interface. The
left-over attributes can cause a crash later on, particularly if the driver
module has been unloaded.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
git commit b2bbb20b37 added direct
support for PXA GPIO D+ pullup as alternative to the older udc_command
ops method. This was done by introduction of the pxa2xx_udc_mach_info
member "gpio_pullup" which, if initialized, is now used in (almost)
all places where udc_command used to be called.
This patch fixes two places where checks for availability of D+ pullup
control still only honor udc_command.
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 196705c9bb. It was
reported to cause a regression by Daniel Exner, and Arjan van de Ven
points out that we actually already have infrastructure in place for
setting limits on acceptable DMA latency that would be the much more
correct fix for the problem with some Broadcom EHCI controllers.
Fixed up trivial conflicts due to the changes to support big-endian host
controller descriptors in drivers/usb/host/{ehci-sched.c,ehci.h}.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes complaints about the gadget stack which are generated by
the currrent "sparse": it doesn't like the fact that zero is the null
pointer. (Last I checked, C guarantees that's correct ...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix serious regression on non-EPiC edgeport usb-serial devices. Baud
rate and MCR/LCR registers are not being written on these models due
to apparent copy-n-paste errors introduced with EPiC support.
Failure reported by Nick Pasich <Nick@NickAndBarb.net>.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove some more dead code from the pxa2xx_udc driver: support
for a no-longer-undocumented hardware "test mode". Newer chips
made this the default, evidently as the best workaround for deep
silicon bugs. The interest was that this seemed to be the only
way to kick in the (documented!) double buffering capability.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes three needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clearly there's a bug in
drivers/usb/serial/usb-serial.c:usb_serial_put(). It shouldn't call
kref_put() while holding a spinlock.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- The outbreak of acute bracketitus has been cured
- The belief that brackets should have spaces everywhere likewise
- Various other coding style tweaks
- Use baud rates not Bfoo in the speed setup switch
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've also enabled the commented out support for 7200, 14400, 55854,
127117 and 3686400 baud as you can now set such rates in the kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as941) fixes a bug recently added to the USB synchronous
API. The status of a completed URB must be preserved separately
across a completion callback. Also, the actual_length value isn't
available until after the URB has fully completed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the scatterlist logic so that PIO options are also disabled
when an IOMMU may have coalesced pages during dma_map_sg() ... it's
not just HIGHMEM that can make trouble supporting both PIO and DMA
based host controller drivers.
There also seems to be a cross-arch issue here, with 64bit powerpc
not using an IOMMU define ... and its IOMMU_VMERGE config can always
be overridden on the kernel command line. So this is better, but
still imperfect.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Montag 23 Juli 2007 schrieb Adrian Bunk:
> Commit ec22559e0b added the following
> function to drivers/usb/serial/usb-serial.c:
>
[..]
>
> The Coverity checker spotted the inconsequent NULL checking for "serial".
>
> Looking at the code it also doesn't seem to have been intended to always
> return 0.
Coverity is right. The check for NULL is wrongly done and the error
return is lost.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds CanoScan N1240U/LiDE30 (Scanner) to the list of quirky USB
devices.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
our list of devices which cannot be suspended keeps growing.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackberry Pearl can run in two modes; a usb-storage only mode
and a mode that allows access via mass storage and to its database.
The berry_charge module will set the device to dual mode and thus we
should ignore its native mode if that module is built
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trivial patch to build the IOWARRIOR when it is selected in Kconfig.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
leds: cr_bllcd.c: build fix
backlight: Convert from struct class_device to struct device
backlight: Fix order of Kconfig entries
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch incorporates some updates. Updates include:
- Fix the problem that control transfer might fail
- Change from GFP_KERNEL to GFP_ATOMIC
- Clean up some coding style issue
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as940 renames hcd_data_lock in hcd.c to hcd_urb_list_lock,
which is more descriptive of the lock's job. It also introduces a
convenient inline routine for testing whether a particular USB device
is a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as939) moves a couple of routine in hcd.c around. The
purpose is to put all the general URB- and endpoint-related routines
(submit, unlink, giveback, and disable) together in one spot.
There are no functional changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch incorporates some updates from the review of the
Renesas m66592-udc driver. Updates include:
- Fix some locking bugs; and add a few sparse annotations
- Don't #define __iomem !
- Lots of whitespace fixes (most of the patch by volume)
- Some #include file trimmage
- Other checkpatch.pl and sparse updates
- Alphabetized and slightly-more-informative Kconfig
- Don't use the ID which was assigned to the amd5536udc driver.
- Remove pointless suspend/resume methods updating obsolete field.
- Some section fixups
- Fix some leak bugs
- Fix byteswapping
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as938) adds an unusual_devs entry for the Nikon DSC D100.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Coverity scan found (CID: 1708) this in
drivers/usb/serial/io_ti.c::edge_shutdown() :
...
2797 for (i=0; i < serial->num_ports; ++i) {
2798 edge_port = usb_get_serial_port_data(serial->port[i]);
2799 edge_remove_sysfs_attrs(edge_port->port);
2800 if (edge_port) {
2801 edge_buf_free(edge_port->ep_out_buf);
2802 kfree(edge_port);
2803 }
2804 usb_set_serial_port_data(serial->port[i], NULL);
2805 }
...
It's complaining that we dereference 'edge_port' in line 2799 which
makes the test of that pointer against NULL in 2800 pointless, since if
edge_port was actually NULL we'd have crashed already before reaching
line 2800.
Reading the edge_open() function it seems to me that the pointer
returned by usb_get_serial_port_data(serial->port[i]) and stored in
'edge_port' can never actually be NULL here, so the test is entirely
superfluous (even if it could be NULL it would be pointless here,
ignoring the then possible crash in that case, since both
edge_buf_free() and kfree() can handle being passed NULL pointers.
This patch removes the pointless conditional (and also makes a few
tiny style corrections now that I was in the area anyway).
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver for the AMD5536 UDC, as found in the AMD Geode CS5536 (southbridge).
This is a high speed DMA-capable controller, which can also be used in
OTG configurations (which are not supported by this patch).
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as936) updates the kerneldoc for usb_unlink_urb. The
explanation of how endpoint queues are meant to work is now clearer
and in better agreement with reality.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It has recently been pointed out that short control transfers should
have a status stage, even if they generate an error because
URB_SHORT_NOT_OK was set. This patch (as935) changes uhci-hcd to
enable the status stage when this happens.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Coverity (1709, 1710, 1711, 1712, 1713) actually flagged these as
REVERSE_INULLs (NULL check performed after dereference). But looking at
the other drivers I can't see any similar tests and the USB core already
makes sure urb is non-null - so might as well get rid of the checks.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as937) fixes a minor bug in the autosuspend usage-counting
code. Each hub's usage counter keeps track of the number of
unsuspended children. However the current driver increments the
counter after registering a new child, by which time the child may
already have been suspended and caused the counter to go negative.
The obvious solution is to increment the counter before registering
the child.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as934) adds a new readonly binary sysfs attribute file
called "descriptors" for each USB device. The attribute contains the
device descriptor followed by the raw descriptor entry (config plug
subsidiary descriptors) for the current configuration.
Having this information available in fixed-format binary makes life a
lot easier for user programs by avoiding the need to open, read, and
parse multiple sysfs text files.
The information in this attribute file is much like that in usbfs's
device file, but there are some significant differences:
The 2-byte fields in the device descriptor are left in
little-endian byte order, as they appear on the bus and
in the kernel.
Only one raw descriptor set is presented, that of the
current configuration.
Opening this file will not cause a suspended device to be
autoresumed.
The last item in particular should be a big selling point for libusb,
which currently forces all USB devices to be resumed as it scans the
device tree.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Dave Mielke <dave@mielke.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as931b), adapted from a patch by Olav Kongas, makes a small
set of conservative changes to the isp116x-hcd driver in preparation
for the removal of urb->status.
finish_request() is moved up in the source and is called
as soon as the URB is known to have completed, rather than
after all the active endpoints have been scanned.
The status of a completed URB is kept in a local variable
and copied to urb->status only when the URB is about to be
given back.
-EREMOTEIO error status for control transfers is set after
the status stage rather than when the short packet arrives.
Some unnecessary uses of urb->lock are removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found the first regresson in the rewritten ("all dynamic" and "no races")
driver. If application uses O_NONBLOCK, I return -EAGAIN despite the URB
being submitted successfuly. This causes the application to resubmit the
same data erroneously.
The fix is to pretend that the transfer has succeeded even if URB was
merely queued. It is the same behaviour as with the old version.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds new devices to the Sierra Wireless driver. This is being
resubmitted because the dependent patch (patch 01/02) needed to be
resubmitted.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds compatibility with Sierra Wireless' new TRU-Install
feature. Future devices that use this feature will not work unless this
patch has been applied.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The FTDI ELAN driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Adutux driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ELAN U132 adapter driver uses the semaphore u132_module_lock
as mutex. Use the mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB gadget serial driver uses a semaphore as mutex. Use the
mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This defines a dev_vdbg() call, which is enabled with -DVERBOSE_DEBUG.
When enabled, dev_vdbg() acts just like dev_dbg(). When disabled, it is a
NOP ... just like dev_dbg() without -DDEBUG. The specific code was moved
out of a USB patch, but lots of drivers have similar support.
That is, code can now be written to use an additional level of debug
output, selected at compile time. Many driver authors have found this
idiom to be very useful. A typical usage model is for "normal" debug
messages to focus on fault paths and not be very "chatty", so that those
messages can be left on during normal operation without much of a
performance or syslog load. On the other hand "verbose" messages would be
noisy enough that they wouldn't normally be enabled; they might even affect
timings enough to change system or driver behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark variables in drivers/* with uninitialized_var() if such a warning
appears, and analysis proves that the var is initialized properly on all
paths it is used.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1) We should only set 'actual_length' output variable if usb length is
known to be good.
2) No need to check actual_length for NULL. The only caller always
passes non-NULL value.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the backlight and LCD classes from struct class_device
to struct device since class_device is scheduled for removal.
One nasty API break is the backlight power attribute has had to be
renamed to bl_power and the LCD power attribute has had to be renamed
to lcd_power since the original names clash with the core. I can't see
a way around this.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit acb11c8b80.
It was broken. We most certainly *do* want the default to be the old
behaviour (and the common case!), instead of breaking everybodys
configuration and making 99% of all people have to override the default.
What were you guys thinking?
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unnecessary cast of return value of kzalloc() in
usb/host/ohci-pnx4008.c
Signed-off-by: Suresh Jayaraman <sjayaraman@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds some scanners reported to be crashed by autosuspend to
the quirk list.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as930) implements autosuspend for usb-storage. It is
adapted from a patch by Oliver Neukum. Autosuspend is allowed except
during LUN scanning, resets, and command execution.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: add new device id to option driver
device is Samsung X180 China cellphone
Signed-off-by: Andrey Arapov <andrey.arapov@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor fixes to goku_udc ... whitespace, let -DDEBUG do its thing,
check the return value of device_register(), sparse tweaks.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Although the other USB driver directories got taught how use Kconfig
and the Makefile to enable the debugging messages enabled by -DDEBUG,
the gadget stack was overlooked.
This patch remedies that omission, but doesn't update any drivers to
remove previous idiosyncracies in this area ... other than the RNDIS
code, which defined its own DEBUG() macro in a broken way.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes controller driver infrastructure which supported
the now-removed usb_ep_{alloc,free}_buffer() calls.
As can be seen, many of the implementations of this were broken to
various degrees. Many didn't properly return dma-coherent mappings;
those which did so were necessarily ugly because of bogosity in the
underlying dma_free_coherent() calls ... which on many platforms
can't be called from the same contexts (notably in_irq) from which
their dma_alloc_coherent() sibling can be called.
The main potential downside of removing this is that gadget drivers
wouldn't have specific knowledge that the controller drivers have:
endpoints that aren't dma-capable don't need any dma mappings at all.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove usb_ep_{alloc,free}_buffer() calls, for small dma-coherent buffers.
This patch just removes the interface and its users; later patches will
remove controller driver support.
- This interface is invariably not implemented correctly in the
controller drivers (e.g. using dma pools, a mechanism which
post-dates the interface by several years).
- At this point no gadget driver really *needs* to use it. In
current kernels, any driver that needs such a mechanism could
allocate a dma pool themselves.
Removing this interface is thus a simplification and improvement.
Note that the gmidi.c driver had a bug in this area; fixed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanups to the pxa2xx_udc code:
- Primarily removing unused DMA hooks.
- One "sparse" warning removed
- Remove some Lubbock-only LED hooks (for debugging)
That DMA code was never really completed. It worked, mostly, for IN
transfers (to the host) if they were fortuitously aligned, but that
code was never fully tested. And it was never coded for OUT transfers
(which is where DMA would really help) ... because of chip errata on
essentially every chip other than the pxa255, and because of design
botches (nothing automated data toggle). So it's effectively been
dead code for several years now ... no point in keeping it around.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch lets the pxa2xx_udc use the generic gpio layer,
on the relevant PXA and IXP systems.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates some of the documentation about DMA buffer management
for USB, and ways to avoid extra copying. Our understanding of the issues
has improved over time.
- Most drivers should *avoid* the dma-coherent allocators. There are
a few exceptions (like the HID driver).
- Some methods are currently commented out; it seems folk writing
USB drivers aren't doing performance tuning at that level yet.
- Just avoid highmem; there's no good way to pass an "I can do highmem
DMA" capability through a driver stack. This is easy, everything
already avoids highmem. But it'd be nice if x86_32 systems with much
physical memory could use it directly with network adapters and mass
storage devices. (Patch, anyone?)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Following patch removes trailing whitespaces at the ends of lines and converts
smarttabs/whitespaces into real tabs.
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The MOS driver is "interesting", in a bad kind of 'how the hell did this
get merged' kind of way
- Remove the bogus termios change check
- Remove the duplicate code for half the ioctls
- Remove the supporting code to duplicate the ioctl code
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So we can use dev_to_node(&usb_dev->dev) later in kmalloc_node to dma buffer
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix an oops that happens in relation with applying work arounds for buggy
ftdi_sio devices. The quirks were handled too early because due to changes in
the initialisation of usb serial devices the device was not fully initialised
when the old hook was called.
Addresses bug 8564
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Generally, Jens Axboe was against 'default y', so I'll have some patches to
remove it.
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make usb autosuspend timers 1sec jiffy aligned.
This helps to reduce the frequency at which the CPU must be taken out of a
lower-power state.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Blackberry devices charge over USB. By autosuspending the port, they are
not able to charge reliably.
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackberry Pearl (8100) needs similar tweaks as older Blackberry models
to be able to charge when connected via USB. The Pearl also adds an
additional need to go into a separate mode for fully accessing the device;
do that by default as well.
Changes based on the changes from bcharge in the barry project
(http://barry.sf.net)
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB_IAD: Adds support for USB Interface Association Descriptors.
This patch adds support to the USB host stack for parsing, storing, and
displaying Interface Association Descriptors. In /proc/bus/usb/devices
lines starting with A: show the fields in an IAD. In sysfs if an
interface on a USB device is referenced by an IAD the following files
will be added to the sysfs directory for that interface:
iad_bFirstInterface, iad_bInterfaceCount, iad_bFunctionClass, and
iad_bFunctionSubClass, iad_bFunctionProtocol
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The loop in usb_sg_wait() is structured in a way that makes it hard to
tell, when the loop exits, whether or not the last URB submission
succeeded. This patch (as928) changes it from a "for" loop to a
"while" loop and keeps "i" always equal to the number of successful
submissions. This fixes an off-by-one error which can show up when
the first URB submission fails.
The patch also removes a couple of lines that initialize fields which
don't need to be initialized.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Root hubs can't be resumed if their parent controller device is still
suspended. This patch (as925) adds a check for that condition in
hcd_bus_resume() and prevents it from being treated as a fatal
controller failure.
ehci-hcd is updated to add the corresponding test. Unnecessary
debugging messages are removed from uhci-hcd and dummy-hcd. The
error return code from dummy-hcd is changed to -ESHUTDOWN, the same as
the others. ohci-hcd doesn't need any changes.
Suspend handling in the non-PCI host drivers is somewhat hit-and-miss.
This patch shouldn't have any effect on them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as922) removes all but one of the remaining vestiges of
dev->power.power_state from usbcore. The only usage left must remain
until the deprecated "power/state" sysfs attribute is gone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch's main bulk aims to make usblp the premier driver for code
pillaging once again. The code is as streamlined as possible and is bug-free
as possible. The usb-skeleton performs the same function, but is somewhat
abstract. The usblp is usb-skeleton which is actually used by many.
Since I combed a few small bugs away, this also fixes the small races we
had in usblp for a while. For example, now it's possible for several threads
to make write(2) calls (sounds silly, but consider a printer for paper
record, where every line of text is self-contained and thus it's all right
to have them interleaved). Also gone are issues with interrupts using
barriers dangerously.
This patch makes use of Oliver's anchor, and so it must trail the anchor
patch on the way to Linus.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a bug that PORT_TYPE and PORT_WIDTH aren't masked correctly in portsc.
Signed-off-by: Christopher Cason <chris.cason@nec.com.au>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch implements autosuspend for the usblcd driver. It uses
the new usb_anchor infrastructure. Many thanks to Georges for testing.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Georges Toth <g.toth@e-biz.lu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
husb2dev was the internal name of the USB Device Controller on
AT32AP7000. Rename it to "atmel_usba", which is closer to the official
name used in documentation and marketing material.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: Add URB_FREE_BUFFER flag for freeing the transfer buffer
In some cases it is not needed that the driver keeps track of the
transfer buffer of an URB. It can be simply freed along with the
URB itself when the reference count goes down to zero. The new
flag URB_FREE_BUFFER enables this behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many device manufacturers are using full-speed bInterval values in high-speed
interrupt endpoint descriptors. If the bInterval value is greater than 16,
assume the device uses full-speed descriptors and fix the value accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Drivers don't call ldisc termios methods. They certainly don't call
them the way this one does - remove wrong call
- The tty buffer code isn't designed to be abused from IRQ handlers and
the new buffering removes the need for the uglies involved - fix them
- Style
- Remove incorrect baud and change handling for termios changes
The driver now has some style, but not a lot - it goes insane if you have
two dongles for example as it continues to use global variables for per
dongle state. That bit isn't my problem.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the baud rate stuff from the kernel don't parse CBAUD directly
Remove pointless and wrong 'no change' check
Could do with some good testing as well but again better than adding &&
BROKEN
(The use of BELKIN_SA_BAUD() might seem a bit odd but x/a = b and x/b =
a (rounded for integers)).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o Don't parse the cflag for baud rates, its not valid to do so
any more and this driver got it wrong anyway
o Don't do clever termios change checks in drivers and get them
wrong (arguably we should do some smart ones in the tty core but
stty to change nothing is *not* a common or critical path
I don't have the hardware so if you can test this carefully please do. I
thought fixing it up this far was better than marking it and other bits of
USB serial && BROKEN
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the ugly code that was copied from the keyspan driver and
allocates the in urbs in a much shorter code path that can be understood
easier.
Also turned off the interrupt urb when no port was open as it's not nice
to keep the bus busy for no good reason at all (this should be a power
savings.)
All in all, this saved over 40 lines of code and cleaned things up
better.
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
You can't rely on the fact that the status really is correct like it was.
Also simplified the write path and now we allocate the urb and data on
the fly, instead of trying to do that really odd timeout check which I
am guessing doesn't really work properly. This should speed up the
device by keeping the hardware queue full easier.
As a benefit, this reduces the size of the driver.
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Peter Berger <pberger@brimson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Stuart Lynne <sl@lineo.com>
Cc: Tom Rushworth <tbr@lineo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Paul Schroeder <pschroeder@uplogix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: VijayaKumar G.N. <vijaykumar@aspirecom.net>
Cc: AjayKumar <ajay@aspirecom.net>
Cc: Gurudeva N. <gurudev@aspirecom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Wolfgang Grandegger <wolfgang@ces.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Thomas Wahrenbruch <linuxusb@kobil.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Utz-Uwe Haus <haus@uuhaus.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Roelf Diedericks <roelfd@inet.co.za>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Ganesh Varadarajan <ganesh@veritas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Peter Berger <pberger@brimson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Peter Berger <pberger@brimson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Hermann Kneissel <herkne@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Kuba Ober <kuba@mareimbrium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <borchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Neil Whelchel <koyama@firstlight.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: <support@reiner-sct.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch releases DMA resources if enqueue fails in the HCD.
Linux had this bug ever since we converted from virt_to_bus for 2.4.
It is difficult to hit. A user would need a significant memory pressure
or some other unusual condition.
It was reported to me by IBM. They ran a management application for
RSA II adapters which sent Bulk requests to an Interrupt endpoint.
Submissions got rejected by HCD due to an invalid interval value
and the swiotlb pool became depleted in the matter of hours.
We fixed the invalid interval issue in devio.c separately, but this
seems to be a bug worth fixing as well.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A noticeable number of low-speed devices mistakenly include
descriptors for Bulk endpoints, which is forbidden by the USB spec.
In an attempt to make such devices more usable, this patch (as924)
converts the descriptors to Interrupt with an interval of 1 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I think there is a race between usb_serial_put() and
usb_serial_get_by_index() (and get_free_serial()) with regards
to handling the serial port refcount.
usb_serial_get_by_index() gets a reference on the serial port under
table_lock while return_serial releases all the returned ports
from the table under the same lock. However, the table_lock is not
taken around the call to kref_put, theoretically allowing to sneak
in and grab a reference after kref_put has already determined that
the reference count is zero (and before calling destroy_serial)
causing use after free.
Signed-off-by: Benny Halevy <bhalevy@ns1.bhalevy.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the USB Specification Revision 2.0 chapter 11.12.5
a hub experiencing an over-current condition must place all
affected ports in the powered-off state. It seems that some root
hubs need port power to be cycled by software in order to get back
to normal functionality after an over-current condition ... like
the EHCI implementation on an MPC8343E.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platforms with PCMCIA support can implement host-side USB with "sl811_cs",
so make sure this menu shows up on platforms with PCMCIA.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as923) makes usb-storage's control thread use
kthread_should_stop()/kthread_stop(). The scanning thread can't be
similarly converted until the core kthread implementation allows
threads to call do_exit().
The advantage of this change is that we can now be certain the control
thread has terminated before storage_disconnect() returns. This will
simplify the locking requirements when autosuspend support is added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the support for the Usb Device Controller on Samsung
S3C24xx SoCs. This driver passes all tests from testusb (including #13)
and has been tested on S3C2410, S3C24212, and S3C2440 SoCs.
Whitespace updates, minor cleanups by David
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB HCD glue updates to reflect the new PS3 unifed device support.
- Fixed remove() routine.
- Added shutdown() routine.
- Added request_mem_region() call.
- Fixed MODULE_ALIAS().
- Made a proper fix for the hack done to support muti-platform in commit
48fda45120.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Might fix bug 8561
On Mon, 4 Jun 2007, Paulo Pereira wrote:
> The patch that you send is not resolving the problem... :(
> I stil have Kernel panic after 45/60 min of work with Ktorrent/Amule...
>
> The Drump is:
>
> Call Trace:
> [<c055fb36>] usb_hcd_submit+0xb1/0x763
> [<f9276488>] ipt_do_table+0x2c7/0x2ef [ip_tables]
> [<f929a6d7>] nf_ct_deliver_cached_events+0x41/0x96 [nf_conntrak]
> [<f9288254>] ipv4_confirm+0x36/0c3b [nf_conntrack_ipv4]
> [<c05ce7c2>] tcp_v4_rcv+0x827/0x899
> [<c05afcc0>] nf_hook_slow+0x4d/0xb5
> [<c042826f>] irq_enter+0x19/0x23
> [<c042826f>] irq_enter+0x19/0x23
> [<c040794c>] do_IRQ+0xbd/0xd1
> [<f90893c9>] option_write+0xa7/0xef [option]
Okay, from this it looks like there's a problem in the option.c serial
driver. Glancing at the code, it's obvious why: The thing totally
abuses the USB API.
Try applying this patch; it should help.
From: Alan Stern <stern@rowland.harvard.edu>
Cc: Paulo Pereira <pfmp.404@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the driver is expecting max ep number in platform
data which isn't passing this information. This patch fix
the problem by reading it from DCCPARAMS(Device Controller
Capability Parameters) register. The change also need some
reordering of the probe code.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as920) adds an extra level of protection to the
USB-Persist facility. Now it will apply by default only to hubs; for
all other devices the user must enable it explicitly by setting the
power/persist device attribute.
The disconnect_all_children() routine in hub.c has been removed and
its code placed inline. This is the way it was originally as part of
hub_pre_reset(); the revised usage in hub_reset_resume() is
sufficiently different that the code can no longer be shared.
Likewise, mark_children_for_reset() is now inline as part of
hub_reset_resume(). The end result looks much cleaner than before.
The sysfs interface is updated to add the new attribute file, and
there are corresponding documentation updates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as919) unifies the code paths used for normal resume and
for reset-resume. Earlier I had failed to note a section in the USB
spec which requires the host to resume a suspended port before
resetting it if the attached device is enabled for remote wakeup.
Since the port has to be resumed anyway, we might as well reuse the
existing code.
The main changes are:
usb_reset_suspended_device() is eliminated.
usb_root_hub_lost_power() is moved down next to the
hub_reset_resume() routine, to which it is logically
related.
finish_port_resume() does a port reset() if the device's
reset_resume flag is set.
usb_port_resume() doesn't check whether the port is initially
enabled if this is a USB-Persist sort of resume.
Code to perform the port reset is added to the resume pathway
for the non-CONFIG_USB_SUSPEND case.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as918) introduces a new USB driver method: reset_resume.
It is called when a device needs to be reset as part of a resume
procedure (whether because of a device quirk or because of the
USB-Persist facility), thereby taking over a role formerly assigned to
the post_reset method. As a consequence, post_reset no longer needs
an argument indicating whether it is being called as part of a
reset-resume. This separation of functions makes the code clearer.
In addition, the pre_reset and post_reset method return types are
changed; they now must return an error code. The return value is
unused at present, but at some later time we may unbind drivers and
re-probe if they encounter an error during reset handling.
The existing pre_reset and post_reset methods in the usbhid,
usb-storage, and hub drivers are updated to match the new
requirements. For usbhid the post_reset routine is also used for
reset_resume (duplicate method pointers); for the other drivers a new
reset_resume routine is added. The change to hub.c looks bigger than
it really is, because mark_children_for_reset_resume() gets moved down
next to the new hub_reset_resume() routine.
A minor change to usb-storage makes the usb_stor_report_bus_reset()
routine acquire the host lock instead of requiring the caller to hold
it already.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as917) removes a now-unnecessary level of subroutine
nesting from hub.c. Since usb_port_suspend() does nothing but call
hub_port_suspend(), and usb_port_resume() does nothing but call
hub_port_resume(), there's no reason to keep the routines separate.
Also included in the patch are a few cosmetic changes involving
whitespace and use of braces.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as916) completes the separation of code paths for suspend
and resume of root hubs as opposed to non-root devices. Root hubs
will be power-managed through their bus_suspend and bus_resume
methods, whereas normal devices will use usb_port_suspend() and
usb_port_resume().
Changes to the hcd_bus_{suspend,resume} routines mostly represent
motion of code that was already present elsewhere. They include:
Adding debugging log messages,
Setting the device state appropriately, and
Adding a resume recovery time delay.
Changes to the port-suspend and port-resume routines in hub.c include:
Removal of checks for root devices (since they will never
be triggered), and
Removal of checks for NULL or invalid device pointers (these
were left over from earlier kernel versions and aren't needed
at all).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as915b) combines the public routine usb_port_suspend() and
the private routine __usb_port_suspend() into a single function.
By removing the explicit mention of otg_port in the call to
__usb_port_suspend(), we prevent a possible error in which the system
tries to perform HNP on the wrong port when a non-targeted device is
plugged into a non-OTG port.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a silicon bug in some NEC OHCI chips. The bug appears
at random times and is very, very difficult to reproduce. Without the
following patch, Linux would shut the chip and its associated devices
down. In Apple PowerBooks this leads to an unusable keyboard and mouse
(SSH still working). The idea of restarting the chip is taken from
public Darwin code.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable file_storage USB_CONFIG_ATT_WAKEUP as it requires
user interaction during Chapter 9 tests.
Signed-off-by: Tony Lindgren <tony@atomide.com
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the endianness select for transfer buffers in EHCI
controllers that have Transaction Translator built in the hub. Also I
cleaned it up to make rid of magic numbers.
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Cc: <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some further cleanup after Oliver's patch to update the tty
buffering. The input buffer is not used at all anymore, so
I removed it.
Signed-off-by: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is an update of the whiteheat driver. It fixes:
- switch from spinlocks to mutexes to prevent sleeping with a spinlock held
- locking to stop races with disconnect
- error handling for commands that time out
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch set introduces usb_anchor and uses it to implement all modern
APIs in the skeleton driver.
- proper error reporting in the skeleton driver
- implementation of flush()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch is to prevent the OTG host of doing 3 times enumeration of
device when the Host suspends for HNP. The error code used in
this case is ENOTSUPP.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a few serial gadget issues reported by the latest "sparse":
some functions should have been defined as static, not just
declared that way.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in order to be able to switch back to 'flow-control none'
after having activated 'flow-control rts/cts', I made
a small change to 'pl2303.c'.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this fixes the flushing trouble due to its own buffering for this driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the new tty buffering code allows usb drivers to stop private buffering.
In fact we must do so to allow flushing to work correctly. This does so
for the visor driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure gadgetfs userspace interface is properly exported:
- Move <linux/usb_gadgetfs.h> to <linux/usb/gadgetfs.h>;
- Export it using Kbuild;
- Add an #include guard;
- Correct some internal documentation;
- Update struct layout so it's the same on 32/64 bit kernels.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Substitute USB instances of __attribute__ ((unused)) functions with the
newly introduced __maybe_unused.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For MPC831x support, change the ehci-fsl driver to preserve
bits set in platform code. Add a common CONFIG_USB_EHCI_FSL
to indicate presence of Freescale EHCI SOC. Add FSL_USB2_DR_OTG
operating mode support, thus both host and device can work for the
mini-ab receptacle. Note: this doesn't enable OTG protocol
support.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now select the big-endian configuration options
CONFIG_USB_EHCI_BIG_ENDIAN_MMIO and CONFIG_USB_EHCI_BIG_ENDIAN_DESC in
the usb host Kconfig file and not in the platform Kconfig files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the AMCC 440EPx EHCI controller whose
in-memory data structures and the registers are represented in big-
endian format.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new FT232RL allows setting and getting the value of the latency
timer, like on the FT232BM. However, the driver will not create the
sysfs entries for the RL without this one-line patch.
I have tested it on two systems with successful results.
From: Stepan Moskovchenko <stevenm86@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as911) replaces some C++-style commented-out debugging
lines in driver.c with a new "verbose debugging" macro. It makes the
code look cleaner, and it's easier to turn the debugging on or off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as908) adds central protection in usbcore for the
prototypical race between opening and unregistering a char device.
The spinlock used to protect the minor-numbers array is replaced with
an rwsem, which can remain locked across a call to a driver's open()
method. This guarantees that open() and deregister() will be mutually
exclusive.
The private locks currently used in several individual drivers for
this purpose are no longer necessary, and the patch removes them. The
following USB drivers are affected: usblcd, idmouse, auerswald,
legousbtower, sisusbvga/sisusb, ldusb, adutux, iowarrior, and
usb-skeleton.
As a side effect of this change, usb_deregister_dev() must not be
called while holding a lock that is acquired by open(). Unfortunately
a number of drivers do this, but luckily the solution is simple: call
usb_deregister_dev() before acquiring the lock.
In addition to these changes (and their consequent code
simplifications), the patch fixes a use-after-free bug in adutux and a
race between open() and release() in iowarrior.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Okay, found it. The root cause here was a missing CONFIG_USB_SUSPEND=y,
which means the hci_usb device never got marked as USB_STATE_SUSPENDED,
which then caused the loop to go on forever.
The system works fine now with CONFIG_USB_SUSPEND=y in the .config.
Here's the patch to prevent future lockups for this or other causes.
I no longer need it, but it does still seem a good idea.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove some dead CONFIG_ symbols, and document the status of a few others.
The "gadget_chips.h" references are by and large to drivers which exist
but haven't yet been submitted for merging to the main 2.6 tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Improvements and fixes to the MCT U232 USB/serial interface driver.
Implement RTS/CTS hardware flow control. Implement HUPCL. Bring
handling of DTR and RTS into conformance with other Linux serial
port drivers - assert both signals when opening device, even if
"crtscts" is not currently selected.
Signed-off-by: Dave Platt <dplatt@radagast.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch modifies the USB regular 250ms timer to be "perfectly aligned" to
the second and quarters thereof. This change is there to make sure that if
you have multiple USB ports, the timers for all these ports will fire at the
same time rather than all spread out. All spread out wakes the CPU up from
power saving idle a lot more than needed...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the most recent Digi EdgePort USB serial
devices.
Signed-off-by: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: Mike Swift <mikes@digi.com>
Signed-off-by: Jeremy McBane <jmcbane@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hermann Kneissel
Maximilian Attems
Alan Stern
David Brownell
Linus Torvalds
Jan Engelhardt
Adam Kropelin
Milinevsky Dmitry
Adrian Bunk
Oliver Neukum
Alan Cox
Oliver Neukum
Johann Felix Soden
Jeremy Katz
Juergen Beisert
Paul Mundt
S.Caglar Onur
Yoshihiro Shimoda
Greg Kroah-Hartman
Jesper Juhl
Thomas Dahlmann
Florin Malita
Pete Zaitcev
Kevin Lloyd
Matthias Kaehlcke
Yoann Padioleau
Jeff Garzik
Al Viro
Rafael J. Wysocki
Richard Purdie
Suresh Jayaraman
Andrey Arapov
Milan Svoboda
Robert P. J. Day
Yinghai Lu
Venki Pallipadi
Craig W. Nadler
Li Yang
Haavard Skinnemoen
Marcel Holtmann
Laurent Pinchart
Benny Halevy
Christian Engelmayer
Arnaud Patard
Geoff Levand
Michael Hanselmann
Tony Lindgren
Vladimir Barinov
Al Borchers
Vikram Pandita
t.sefzick
David Rientjes
Stefan Roese
Stepan Moskovchenko
Mark Lord
Dave Platt
Arjan van de Ven
Martin K. Petersen