Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
[Blackfin] arch: current_l1_stack_save is a pointer, so use NULL rather than 0
[Blackfin] arch: fix atomic and32/xor32 comments and ENDPROC markings
[Blackfin] arch: fix bug - allow SDH driver to be used as module
[Blackfin] arch: to kill syscalls missing warning by adding new timerfd syscalls
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] kprobes arch consolidation build fix
[IA64] update efi region debugging to use MB, GB and TB as well as KB
[IA64] use dev_printk in video quirk
[IA64] remove remaining __FUNCTION__ occurrences
[IA64] remove unnecessary nfs includes from sys_ia32.c
[IA64] remove CONFIG_SMP ifdef in ia64_send_ipi()
[IA64] arch_ptrace() cleanup
[IA64] remove duplicate code from arch_ptrace()
[IA64] convert sys_ptrace to arch_ptrace
[IA64] remove find_thread_for_addr()
[IA64] do not sync RBS when changing PT_AR_BSP or PT_CFM
[IA64] access user RBS directly
ia64 named their handler kprobes_fault_handler while all other
arches used kprobe_fault_handler. Change the function definition
and header declaration.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When EFI_DEBUG is defined to a non-zero value in arch/ia64/kernel/efi.c,
the efi memory regions are displayed. This patch enhances the
display code in a few ways:
1. Use TB, GB and MB as well as KB as units.
Although this introduces rounding errors (KB doesn't as
size is always a multiple of 4Kb), it does make
things a lot more readable.
Also as the range is also shown, it is possible to note the exact size
if it is important. In my experience, the size field is mostly useful
for getting a general idea of the size of a region.
On the rx2620 that I use, there actually is an 8TB region (though not
backed by physical memory, and 8TB really is a lot more readable than
8589934592KB.
2. pad the size field with leading spaces to further improve readability
...
... ( 8MB)
... ( 928MB)
... ( 3MB)
...
vs
...
... (8MB)
... (928MB)
... (3MB)
...
3. Pad the attr field out to 64bits using leading zeros,
to further improve readability.
...
mem05: type= 2, attr=0x0000000000000008, range=[0x0000000004000000-0x000000000481f000) ( 8MB)
mem06: type= 7, attr=0x0000000000000008, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) ( 3MB)
mem08: type= 4, attr=0x0000000000000008, range=[0x000000003eb8e000-0x000000003ee7a000) ( 2MB)
...
...
mem05: type= 2, attr=0x8, range=[0x0000000004000000-0x000000000481f000) ( 8MB)
mem06: type= 7, attr=0x8, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) ( 3MB)
mem08: type= 4, attr=0x8, range=[0x000000003eb8e000-0x000000003ee7a000) ( 2MB)
...
4. Use %d instead of %u for the index field, as i is a signed int.
N.B: This code is not compiled unless EFI_DEBUG is non 0.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
__FUNCTION__ is gcc-specific, use __func__
Long lines have been kept where they exist, some small spacing changes
have been done.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Compilation of 2.6.25-rc2-mm1 on ia64 generates many warnings.
IA64 support 2 ELF format (IA64 binary and IA32 binary),
thus if 2 elf related header included, cause many warning or error.
about 2 week ago, J. Bruce Fields proposed this problem fixed patch.
(http://marc.info/?l=linux-ia64&m=120329313305695&w=2)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When !CONFIG_SMP, cpu_physical_id() is ia64_get_lid(), which is
functionally identical to
(ia64_getreg(_IA64_REG_CR_LID) >> 16) & 0xffff
so there's no need for two versions of this code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The only board-specific bits that existed here were for setting up the
IRQs, which are now handled by the SH7710 CPU support code instead. As
there's nothing else to do for setup, kill off the board support code
and have the defconfig use the generic machvec instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's still work that needs to be done here, and this should not be
enabled by default on existing boards.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This disables the PMB/32BIT=y by default in r7780mp, as turning this on
presently results in build errors (for an admittedly experimental
feature).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the old non-verbose hp6xx apm code and enables some
very basic apm output. We now get percentage (battery) output
and basic time estimate.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ERROR: "copy_page" [fs/unionfs/unionfs.ko] undefined!
like all the other architectures.
Cc: Erez Zadok <ezk@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following compile error:
<-- snip -->
...
CC arch/sh/mm/pg-sh7705.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c: In function 'ptep_get_and_clear':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c:130: error: implicit declaration of function 'mapping_writably_mapped'
make[2]: *** [arch/sh/mm/pg-sh7705.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove all code which does exactly the same thing as ptrace_request().
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
find_thread_for_addr() is no longer needed. It was only used to find
the correct kernel RBS for a given memory address, but since the kernel
RBS is not needed any longer, this function can go away.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Syncing is no longer needed, because user RBS is already
up-to-date. Actually, if a debugger modified the contents
of the original RBS prior to changing PT_AR_BSP, the
modifications would get overwritten.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Because the user RBS of a process is now completely stored in
user-mode when the process is ptrace-stopped, accesses to the
RBS should no longer augment any part of the kernel RBS.
This means we can get rid of most ia64_peek() and ia64_poke()
calls.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We don't need to printk a message every time we transition.
Leave the code there, but ifdef'd out, as it's useful when
adding support for new processors.
Reported-by: Petr Titěra <P.Titera@century.cz>
Signed-off-by: Dave Jones <davej@redhat.com>
Add functions to manage the channel syncronization flags to dma_lib
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Also stop both rx and tx sections before changing the configuration of
the dma device during init.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
/sys/firmware/reipl/nss/name contains the nss name when defsys or
savesys command has been executed. If the defsys or savesys command
fails the kernel_nss_name has to be cleared since a reipl on that
nss name won't be possible.
Signed-off-by: Hongjie Yang <hongjie@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Normally this should not happen, but it's cleaner to do it that way.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
IPL from NSS didn't work because the memory detection routine omits any
memory sections with a size lower than what MAX_ORDER defines.
This causes the detection routine to skip the first memory segment which
has a size of 1MB. Which later on will let the kernel think that there
is no memory available at all.
Since in addition the z/VM memory increment size is 1MB force MAX_ORDER
to be 9, so we can support 1MB segments.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Compile smp.o with -Wno-nonnull so gcc stops warning about memcpy
being used with a null parameter. Also remove the workaround code
and use a char * cast instead of a void * cast to do computations.
Cc: Bastian Blank <bastian@waldi.eu.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a machine check handling is pending when the idle loop is entered
default_idle will be left with timer ticks and virtual timer disabled.
Fix this by "calling" the idle_chain. Also a BUG_ON(!in_interrupt) in
start_hz_timer must be removed since the function now gets called from
non interrupt context as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fix ia64 kprobes compilation
[IA64] move gcc_intrin.h from header-y to unifdef-y
[IA64] workaround tiger ia64_sal_get_physical_id_info hang
[IA64] move defconfig to arch/ia64/configs/
[IA64] Fix irq migration in multiple vector domain
[IA64] signal(ia64_ia32): add a signal stack overflow check
[IA64] signal(ia64): add a signal stack overflow check
[IA64] CONFIG_SGI_SN2 - auto select NUMA and ACPI_NUMA
Function __copy_user_zeroing in arch/lib/usercopy.c had the wrong parameter
set as __user, and in include/asm-cris/uaccess.h, it was not set at all for
some of the calling functions.
This will cut the number of warnings quite dramatically when using sparse.
While we're here, remove useless CVS log and correct confusing typo.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This just removes unused DEBUG_FORCEDAC define in the IOMMU code.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the IOMMU code not allocate a memory area spanning LLD's
segment boundary.
is_span_boundary() judges whether a memory area spans LLD's segment boundary.
If iommu_arena_find_pages() finds such a area, it tries to find the next
available memory area.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
iommu_arena_find_pages duplicates the code to access to the bitmap for free
space management. This patch convert the IOMMU code to have only one place to
access the bitmap, in the popular way that other IOMMUs (e.g. POWER and
SPARC) do.
This patch is preparation for modifications to fix the IOMMU segment boundary
problem.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is preparation for modifications to fix the IOMMU segment boundary
problem.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk reported another compile error with a SVN head GCC:
...
CC arch/cris/arch-v10/lib/string.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:138:
error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:138:
error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:139:
error: lvalue required as increment operand
...
This is due to the use of the construct:
*((long*)dst)++ = lc;
Which isn't legal since casts don't return an lvalue.
The solution is to import the implementation from newlib,
which is continually autotested together with GCC mainline,
and uses the construct:
*(long *) dst = lc; dst += 4;
Since this is an import of a file from newlib, I'm not touching
the formatting or correcting any checkpatch errors.
As for the earlier fix for memset.c, even if the two files for
CRIS v10 and CRIS v32 are identical at the moment, it might
be possible to tweak the CRIS v32 version.
Thus, I'm not yet folding them into the same file, at least not
until we've done some research on it.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add CONFIG_HAVE_KRETPROBES to the arch/<arch>/Kconfig file for relevant
architectures with kprobes support. This facilitates easy handling of
in-kernel modules (like samples/kprobes/kretprobe_example.c) that depend on
kretprobes being present in the kernel.
Thanks to Sam Ravnborg for helping make the patch more lean.
Per Mathieu's suggestion, added CONFIG_KRETPROBES and fixed up dependencies.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2f569afd9c
(CONFIG_HIGHPTE vs. sub-page page tables) introduced use of
inc_zone_page_state and dec_zone_page_state in include/linux/mm.h.
Those are defined in include/linux/vmstat.h, but after it includes
mm.h, making it impossible to include vmstat.h since inc_zone_page_state
and dec_zone_page_state then would be undefined.
arch/cris/arch-v10/kernel/time.c does just this, which makes the
CRIS v10 build break with the following error:
...
CC arch/cris/arch-v10/kernel/time.o
In file included from include/linux/vmstat.h:7,
from arch/cris/arch-v10/kernel/time.c:17:
include/linux/mm.h: In function 'pgtable_page_ctor':
include/linux/mm.h:902: error: implicit declaration of function 'inc_zone_page_state'
include/linux/mm.h: In function 'pgtable_page_dtor':
include/linux/mm.h:908: error: implicit declaration of function 'dec_zone_page_state'
make[2]: *** [arch/cris/arch-v10/kernel/time.o] Error 1
make[1]: *** [arch/cris/arch-v10/kernel] Error 2
make: *** [sub-make] Error 2
...
By changing kernel/time.c to include linux/mm.h, the build succeeds.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following compile error with a recent gcc:
CC kernel/kprobes.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/kernel/kprobes.c:1066: error: __ksymtab_jprobe_return causes a section type conflict
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes regression introduced in 113134fcbc
Intel Tiger platforms hang when calling SAL_GET_PHYSICAL_ID_INFO
instead of properly returning -1 for unimplemented, so add a
version check.
SGI Altix platforms have an incorrect SAL version hard-coded into
their prom -- they encode 2.9, but actually implement 3.2 -- so
fix it up and allow ia64_sal_get_physical_id_info to keep
working.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch moves the default ia64 defconfig to
arch/ia64/configs/generic_defconfig where it belongs and selects it as
the default defconfig through KBUILD_DEFCONFIG.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that the following error message is sometimes displayed
at irq migration when vector domain is enabled.
"Unexpected interrupt vector %d on CPU %d is not mapped to any IRQ!"
The cause of this problem is an interrupt is sent to the previous
target CPU after cleaning up vector to irq mapping table. To clean up
vector to irq map on the previous target CPU safty, change the irq
migration in multiple vector domain as follows. The original idea is
from x86 interrupt management code.
- Delay vector to irq table cleanup until the interrupts are sent
to new target CPUs. By this, it is ensured that target CPU is
completely changed on the interrupt controller side.
- Even after the interrupts are sent to new target CPUs, there can
be pended interrupts remaining on the previous target CPU. So we
need to delay clearning up vector to irq table until the pended
interrupt is handled. For this, send IPI to the previous target
CPU with lower priority vector and clean up vector to irq table
in its handler.
This patch affects only to irq migration code with multiple vector
domain is enabled.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The similar check has been added to x86_32(i386) in commit
id 83bd01024b.
So we add this check to ia64_ia32 and improve it a liitle bit in that
we need to check for stack overflow only when the signal is on stack.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The similar check has been added to x86_32(i386) in commit
id 83bd01024b.
So we add this check to ia64 and improve it a liitle bit in that
we need to check for stack overflow only when the signal is on stack.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Auto select CONFIG_NUMA and CONFIG_ACPI_NUMA when picking SN2, similar
to how they are selected automatically for CONFIG_IA64_GENERIC.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
P4 has been coming out as CPU_FAMILY=4 instead of 6: fix MPENTIUM4 typo.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86/xen: fix DomU boot problem
x86: not set node to cpu_to_node if the node is not online
x86, i387: fix ptrace leakage using init_fpu()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
x86: disable KVM for Voyager and friends
KVM: VMX: Avoid rearranging switched guest msrs while they are loaded
KVM: MMU: Fix race when instantiating a shadow pte
KVM: Route irq 0 to vcpu 0 exclusively
KVM: Avoid infinite-frequency local apic timer
KVM: make MMU_DEBUG compile again
KVM: move alloc_apic_access_page() outside of non-preemptable region
KVM: SVM: fix Windows XP 64 bit installation crash
KVM: remove the usage of the mmap_sem for the protection of the memory slots.
KVM: emulate access to MSR_IA32_MCG_CTL
KVM: Make the supported cpuid list a host property rather than a vm property
KVM: Fix kvm_arch_vcpu_ioctl_set_sregs so that set_cr0 works properly
KVM: SVM: set NM intercept when enabling CR0.TS in the guest
KVM: SVM: Fix lazy FPU switching
Construct Xen guest e820 map with a hole between 640K-1M.
It's pure luck that Xen kernels have gotten away with it in the past.
The patch below seems like the right thing to do. It certainly boots in
a domU without the DMI problem (without any of the other related patches
such as Alexander's).
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Tested-by: Mark McLoughlin <markmc@redhat.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
resolve boot problem reported by Mel Gorman:
http://lkml.org/lkml/2008/2/13/404
init_cpu_to_node will use cpu->apic (from MADT or mptable) and
apic->node(from SRAT or AMD config space with k8_bus_64.c) to have
cpu->node mapping, and later identify_cpu will overwrite them
again...(with nearby_node...)
this patch checks if the node is online, otherwise it will not
update cpu_node map. so keep cpu_node map to online node before
identify_cpu..., to prevent possible error.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
This bug got introduced by the recent i387 merge:
commit 4421011120
Author: Roland McGrath <roland@redhat.com>
Date: Wed Jan 30 13:31:50 2008 +0100
x86: x86 i387 user_regset
Current usage of unlazy_fpu() in ptrace specific routines is wrong.
unlazy_fpu() will not init fpu if the task never used math. So the
ptrace calls can expose the parent tasks FPU data in some cases.
Replace it with the init_fpu() which will init the math state, if the
task never used math before.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
m68k{,nommu}: Wire up the new timerfd syscalls, which were introduced in
commit 4d672e7ac7 ("timerfd: new timerfd API").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most classic Pentiums don't have hardware virtualization extension,
and building kvm with Voyager, Visual Workstation, or NUMAQ
generates spurious failures.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
KVM tries to run as much as possible with the guest msrs loaded instead of
host msrs, since switching msrs is very expensive. It also tries to minimize
the number of msrs switched according to the guest mode; for example,
MSR_LSTAR is needed only by long mode guests. This optimization is done by
setup_msrs().
However, we must not change which msrs are switched while we are running with
guest msr state:
- switch to guest msr state
- call setup_msrs(), removing some msrs from the list
- switch to host msr state, leaving a few guest msrs loaded
An easy way to trigger this is to kexec an x86_64 linux guest. Early during
setup, the guest will switch EFER to not include SCE. KVM will stop saving
MSR_LSTAR, and on the next msr switch it will leave the guest LSTAR loaded.
The next host syscall will end up in a random location in the kernel.
Fix by reloading the host msrs before changing the msr list.
Signed-off-by: Avi Kivity <avi@qumranet.com>
For improved concurrency, the guest walk is performed concurrently with other
vcpus. This means that we need to revalidate the guest ptes once we have
write-protected the guest page tables, at which point they can no longer be
modified.
The current code attempts to avoid this check if the shadow page table is not
new, on the assumption that if it has existed before, the guest could not have
modified the pte without the shadow lock. However the assumption is incorrect,
as the racing vcpu could have modified the pte, then instantiated the shadow
page, before our vcpu regains control:
vcpu0 vcpu1
fault
walk pte
modify pte
fault in same pagetable
instantiate shadow page
lookup shadow page
conclude it is old
instantiate spte based on stale guest pte
We could do something clever with generation counters, but a test run by
Marcelo suggests this is unnecessary and we can just do the revalidation
unconditionally. The pte will be in the processor cache and the check can
be quite fast.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the local apic initial count is zero, don't start a an hrtimer with infinite
frequency, locking up the host.
Signed-off-by: Avi Kivity <avi@qumranet.com>
the cr3 variable is now inside the vcpu->arch structure.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
alloc_apic_access_page() can sleep, while vmx_vcpu_setup is called
inside a non preemptable region. Move it after put_cpu().
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
While installing Windows XP 64 bit wants to access the DEBUGCTL and the last
branch record (LBR) MSRs. Don't allowing this in KVM causes the installation to
crash. This patch allow the access to these MSRs and fixes the issue.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch replaces the mmap_sem lock for the memory slots with a new
kvm private lock, it is needed beacuse untill now there were cases where
kvm accesses user memory while holding the mmap semaphore.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Reported by Adrian Bunk.
Just like in changeset a3f9985843
("[SPARC64]: Move kernel unaligned trap handlers into assembler
file.") we have to move the assembler bits into a seperate
asm file because as far as the compiler is concerned
these inline bits we're doing in unaligned.c are unreachable.
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: revert "x86: fix pmd_bad and pud_bad to support huge pages"
x86: revert "x86: CPA: avoid split of alias mappings"
Revert:
commit 8be8f54bae
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Sat Feb 23 20:43:21 2008 +0100
x86: CPA: avoid split of alias mappings
because it clearly mishandles the case when __change_page_attr(), called
from __change_page_attr_set_clr(), changes cpa->processed to 1 and
cpa_process_alias(cpa) is executed right after that.
This crashes my x86-64 test box early in the boot process
(ref. http://bugzilla.kernel.org/show_bug.cgi?id=10140#c4).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Injecting an GP when accessing this MSR lets Windows crash when running some
stress test tools in KVM. So this patch emulates access to this MSR.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
One of the use cases for the supported cpuid list is to create a "greatest
common denominator" of cpu capabilities in a server farm. As such, it is
useful to be able to get the list without creating a virtual machine first.
Since the code does not depend on the vm in any way, all that is needed is
to move it to the device ioctl handler. The capability identifier is also
changed so that binaries made against -rc1 will fail gracefully.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Whilst working on getting a VM to initialize in to IA32e mode I found
this issue. set_cr0 relies on comparing the old cr0 to the new one to
work correctly. Move the assignment below so the compare can work.
Signed-off-by: Paul Knowles <paul@transitive.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Explicitly enable the NM intercept in svm_set_cr0 if we enable TS in the guest
copy of CR0 for lazy FPU switching. This fixes guest SMP with Linux under SVM.
Without that patch Linux deadlocks or panics right after trying to boot the
other CPUs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the guest writes to cr0 and leaves the TS flag at 0 while vcpu->fpu_active
is also 0, the TS flag in the guest's cr0 gets lost. This leads to corrupt FPU
state an causes Windows Vista 64bit to crash very soon after boot. This patch
fixes this bug.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The only tricky part is we need to adjust the PTE insertion loop to
cater for holes in the page table. The PTEs for each segment start on
a 4K boundary, so with 16M pages we have 16 PTEs per segment and then
a gap to the next 4K page boundary.
It might be possible to allocate the PTEs for each segment separately,
saving the memory currently filling the gaps. However we'd need to
check that's OK with the hardware, and that it actually saves memory.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Make some preliminary changes to cell_iommu_alloc_ptab() to allow it to
take the page size as a parameter rather than assuming IOMMU_PAGE_SIZE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We use n_pte_pages to calculate the stride through the page tables, but
we also use it to set the NPPT value in the segment table entry. That is
defined as the number of 4K pages per segment, so we should calculate
it as such regardless of the IOMMU page size.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently the cell IOMMU code allocates the entire IOMMU page table in a
contiguous chunk. This is nice and tidy, but for machines with larger
amounts of RAM the page table allocation can fail due to it simply being
too large.
So split the segment table and page table setup routine, and arrange to
have the dynamic and fixed page tables allocated separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There's no need to allocate the pad page unless we're going to actually
use it - so move the allocation to where we know we're going to use it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cell IOMMU code no longer needs to save the pte_offset variable
separately, it is incorporated into tbl->it_offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cell IOMMU tce build and free routines use pte_offset to convert
the index passed from the generic IOMMU code into a page table offset.
This takes into account the SPIDER_DMA_OFFSET which sets the top bit
of every DMA address.
However it doesn't cater for the IOMMU window starting at a non-zero
address, as the base of the window is not incorporated into pte_offset
at all.
As it turns out tbl->it_offset already contains the value we need, it
takes into account the base of the window and also pte_offset. So use
it instead!
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It's called the fixed mapping, not the static mapping.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Ulrich Weigand has found that the hardware watchpoints on cell were not
working back in November :
http://ozlabs.org/pipermail/linuxppc-dev/2007-November/046135.html
This patch sets them during initialization.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This moves the private DABRX definitions for celleb from beat.h to
reg.h to make them usable for all.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch enables OProfile callgraph support for the Cell processor. The
original code was just calling a function to add the PC value, now it will
call a function that first checks the callgraph depth. Callgraph is already
enabled on the other Power platforms.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Li Yang
Linus Torvalds
Harvey Harrison
Simon Horman
Bjorn Helgaas
KOSAKI Motohiro
Paul Mundt
Kristoffer Ericson
goda.yusuke
Andrew Morton
Adrian Bunk
Petr Tesarik
Dave Jones
Olof Johansson
Hongjie Yang
Michael Holzheu
Heiko Carstens
Martin Schwidefsky
Jesper Nilsson
FUJITA Tomonori
Ananth N Mavinakayanahalli
Adrian Bunk
Alex Chiang
Kenji Kaneshige
Shi Weihua
Jes Sorensen
Hugh Dickins
Ian Campbell
Yinghai Lu
Suresh Siddha
Geert Uytterhoeven
Greg Ungerer
Randy Dunlap
Avi Kivity
Marcelo Tosatti
Joerg Roedel
Izik Eidus
Mike Frysinger
Michael Hennerich
Bryan Wu
David S. Miller
Rafael J. Wysocki
Paul Mackerras
Paul Knowles
Michael Ellerman
Jens Osterkamp
Bob Nelson