Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e1612
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:
- if (de->proc_fops)
- inode->i_fop = de->proc_fops;
+ if (de->proc_fops) {
+ if (S_ISREG(inode->i_mode))
+ inode->i_fop = &proc_reg_file_ops;
+ else
+ inode->i_fop = de->proc_fops;
+ }
VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our chosen ic_dev may be anywhere in our list of ic_devs, and we may
free it before attempting to close others. When we compare d->dev and
ic_dev->dev, we're potentially dereferencing memory returned to the
allocator. This causes KASAN to scream for each subsequent ic_dev we
check.
As there's a 1-1 mapping between ic_devs and netdevs, we can instead
compare d and ic_dev directly, which implicitly handles the !ic_dev
case, and avoids the use-after-free. The ic_dev pointer may be stale,
but we will not dereference it.
Original splat:
[ 6.487446] ==================================================================
[ 6.494693] BUG: KASAN: use-after-free in ic_close_devs+0xc4/0x154 at addr ffff800367efa708
[ 6.503013] Read of size 8 by task swapper/0/1
[ 6.507452] CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc3-00002-gda42158 #8
[ 6.514993] Hardware name: AppliedMicro Mustang/Mustang, BIOS 3.05.05-beta_rc Jan 27 2016
[ 6.523138] Call trace:
[ 6.525590] [<ffff200008094778>] dump_backtrace+0x0/0x570
[ 6.530976] [<ffff200008094d08>] show_stack+0x20/0x30
[ 6.536017] [<ffff200008bee928>] dump_stack+0x120/0x188
[ 6.541231] [<ffff20000856d5e4>] kasan_object_err+0x24/0xa0
[ 6.546790] [<ffff20000856d924>] kasan_report_error+0x244/0x738
[ 6.552695] [<ffff20000856dfec>] __asan_report_load8_noabort+0x54/0x80
[ 6.559204] [<ffff20000aae86ac>] ic_close_devs+0xc4/0x154
[ 6.564590] [<ffff20000aaedbac>] ip_auto_config+0x2ed4/0x2f1c
[ 6.570321] [<ffff200008084b04>] do_one_initcall+0xcc/0x370
[ 6.575882] [<ffff20000aa31de8>] kernel_init_freeable+0x5f8/0x6c4
[ 6.581959] [<ffff20000a16df00>] kernel_init+0x18/0x190
[ 6.587171] [<ffff200008084710>] ret_from_fork+0x10/0x40
[ 6.592468] Object at ffff800367efa700, in cache kmalloc-128 size: 128
[ 6.598969] Allocated:
[ 6.601324] PID = 1
[ 6.603427] save_stack_trace_tsk+0x0/0x418
[ 6.607603] save_stack_trace+0x20/0x30
[ 6.611430] kasan_kmalloc+0xd8/0x188
[ 6.615087] ip_auto_config+0x8c4/0x2f1c
[ 6.619002] do_one_initcall+0xcc/0x370
[ 6.622832] kernel_init_freeable+0x5f8/0x6c4
[ 6.627178] kernel_init+0x18/0x190
[ 6.630660] ret_from_fork+0x10/0x40
[ 6.634223] Freed:
[ 6.636233] PID = 1
[ 6.638334] save_stack_trace_tsk+0x0/0x418
[ 6.642510] save_stack_trace+0x20/0x30
[ 6.646337] kasan_slab_free+0x88/0x178
[ 6.650167] kfree+0xb8/0x478
[ 6.653131] ic_close_devs+0x130/0x154
[ 6.656875] ip_auto_config+0x2ed4/0x2f1c
[ 6.660875] do_one_initcall+0xcc/0x370
[ 6.664705] kernel_init_freeable+0x5f8/0x6c4
[ 6.669051] kernel_init+0x18/0x190
[ 6.672534] ret_from_fork+0x10/0x40
[ 6.676098] Memory state around the buggy address:
[ 6.680880] ffff800367efa600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 6.688078] ffff800367efa680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 6.695276] >ffff800367efa700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 6.702469] ^
[ 6.705952] ffff800367efa780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 6.713149] ffff800367efa800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 6.720343] ==================================================================
[ 6.727536] Disabling lock debugging due to kernel taint
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: David S. Miller <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If no RARP, BOOTP, or DHCP response is received, ic_dev is never set,
causing a NULL pointer dereference in ic_close_devs():
Sending DHCP requests ...... timed out!
Unable to handle kernel NULL pointer dereference at virtual address 00000004
To fix this, add a check to avoid dereferencing ic_dev if it is still
NULL.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 2647cffb2b ("net: ipconfig: Support using "delayed" DHCP replies")
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit 9c706a49d6 ("net: ipconfig: fix use after free") avoids
the use after free, the resulting code still ends up calling both the
ic_setup_if() and ic_setup_routes() after calling ic_close_devs(), and
access to the device is still required.
Move the call to ic_close_devs() to the very end of the function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ic_close_devs() calls kfree() for all devices's ic_device. Since commit
2647cffb2b ("net: ipconfig: Support using "delayed" DHCP replies")
the active device's ic_device is still used however to print the
ipconfig summary which results in an oops if the memory is already
changed. So delay freeing until after the autoconfig results are
reported.
Fixes: 2647cffb2b ("net: ipconfig: Support using "delayed" DHCP replies")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ipconfig learned to handle "delayed replies" in the previous
commit, there is no reason any more to delay sending a first request per
device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dhcp code only waits 1s between sending DHCP requests on different
devices and only accepts an answer for the device that sent out the last
request. Only the timeout at the end of a loop is increased iteratively
which favours only the last device. This makes it impossible to work
with a dhcp server that takes little more than 1s connected to a device
that is not the last one.
Instead of also increasing the inter-device timeout, teach the code to
handle delayed replies.
To accomplish that, make *ic_dev track the current ic_device instead of
the current net_device and adapt all users accordingly. The relevant
change then is to reset d to ic_dev on a reply to assert that the
followup request goes through the right device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies understanding what happens when there is more than one
device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
>> net/ipv4/ipconfig.c:130:15: warning: 'ic_addrservaddr' defined but not used [-Wunused-variable]
static __be32 ic_addrservaddr = NONE; /* IP Address of the IP addresses'server */
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The symbol ic_addrservaddr is not static, but has no declaration
to match so make it static to fix the following warning:
net/ipv4/ipconfig.c:130:8: warning: symbol 'ic_addrservaddr' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PROC_FS, CONFIG_IP_PNP_BOOTP, CONFIG_IP_PNP_DHCP and
CONFIG_IP_PNP_RARP are all disabled, we get a warning about the
ic_proto_used variable being unused:
net/ipv4/ipconfig.c:146:12: error: 'ic_proto_used' defined but not used [-Werror=unused-variable]
This avoids the warning, by making the definition conditional on
whether a dynamic IP configuration protocol is configured. If not,
we know that the value is always zero, so we can optimize away the
variable and all code that depends on it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 09605cc12c ("net ipv4: use preferred log methods") replaced
a few calls of pr_cont() after a console print without a trailing
newline by pr_info(), causing lines to be split during IP
autoconfiguration, like:
.
,
OK
IP-Config: Got DHCP answer from 192.168.97.254,
my address is 192.168.97.44
Convert these back to using pr_cont(), so it prints again:
., OK
IP-Config: Got DHCP answer from 192.168.97.254, my address is 192.168.97.44
Absorb the printing of "my address ..." into the previous call to
pr_info(), as there's no reason to use a continuation there.
Convert one more pr_info() to print nameservers while we're at it.
Fixes: 09605cc12c ("net ipv4: use preferred log methods")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace printk calls with preferred unconditional log method calls to keep
kernel messages clean.
Added newline to "too small MTU" message.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A dhcp server may provide parameters to a client from a pool of IP
addresses and using a shared rootfs, or provide a specific set of
parameters for a specific client, usually using the MAC address to
identify each client individually. The dhcp protocol also specifies
a client-id field which can be used to determine the correct
parameters to supply when no MAC address is available. There is
currently no way to tell the kernel to supply a specific client-id,
only the userspace dhcp clients support this feature, but this can
not be used when the network is needed before userspace is available
such as when the root filesystem is on NFS.
This patch is to be able to do something like "ip=dhcp,client_id_type,
client_id_value", as a kernel parameter to enable the kernel to
identify itself to the server.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a system has multiple ethernet devices and during DHCP
request (for using NFS), the system waits only for HZ/2 which is
500mS before switching to another interface for DHCP.
There are some routers (Ex: Trendnet routers) which responds to
DHCP request at about 560mS. When the system has only one
ethernet interface there is no issue as the timeout is 2S and the
dev xid doesn't changes and only retries.
But when the system has multiple Ethernet like DRA74x with CPSW
in dual EMAC mode, the DHCP response is dropped as the dev xid
changes while shifting to the next device. So changing inter
device timeout to HZ (which is 1S).
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 code uses a mixture of coding styles. In some instances check
for NULL pointer is done as x == NULL and sometimes as !x. !x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic to configure a network interface for kernel IP
auto-configuration is very simplistic, and does not handle the case
where a device is stacked onto another such as with DSA. This causes the
kernel not to open and configure the master network device in a DSA
switch tree, and therefore slave network devices using this master
network devices as conduit device cannot be open.
This restriction comes from a check in net/dsa/slave.c, which is
basically checking the master netdev flags for IFF_UP and returns
-ENETDOWN if it is not the case.
Automatically bringing-up DSA master network devices allows DSA slave
network devices to be used as valid interfaces for e.g: NFS root booting
by allowing kernel IP autoconfiguration to succeed on these interfaces.
On the reverse path, make sure we do not attempt to close a DSA-enabled
device as this would implicitely prevent the slave DSA network device
from operating.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unsigned char *sha (source) was already in original git version
but was never used.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the Coccinelle semantic patch making this change
is as follows:
@change@
expression E1,E2;
@@
- jiffies - E1 < E2
+ time_before(jiffies, E1+E2)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is only tested, and declared, in the bootp code.
So, in ic_dynamic() guard it's setting with IPCONFIG_BOOTP.
Signed-off-by: David S. Miller <davem@davemloft.net>
ic_dev_xid is only used in __init ic_bootp_recv under IPCONFIG_BOOTP
and __init ic_dynamic under IPCONFIG_DYNAMIC(which is itself defined
with the same IPCONFIG_BOOTP)
This patch fixes the following warning when IPCONFIG_BOOTP is not set:
>> net/ipv4/ipconfig.c:146:15: warning: 'ic_dev_xid' defined but not used [-Wunused-variable]
static __be32 ic_dev_xid; /* Device under configuration */
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
ic_dev_xid is only used in ipconfig.c
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the 'time_before' macro expand with parentheses, the look is bad.
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3fb72f1e6e ("ipconfig wait
for carrier") added a "wait for carrier on at least one interface"
policy, with a worst case maximum wait of two minutes.
However, if you encounter this, you won't get any feedback from
the console as to the nature of what is going on. You just see
the booting process hang for two minutes and then continue.
Here we add a message so the user knows what is going on, and
hence can take action to rectify the situation (e.g. fix network
cable or whatever.) After the 1st 10s pause, output now begins
that looks like this:
Waiting up to 110 more seconds for network.
Waiting up to 100 more seconds for network.
Waiting up to 90 more seconds for network.
Waiting up to 80 more seconds for network.
...
Since most systems will have no problem getting link/carrier in the
1st 10s, the only people who will see these messages are people with
genuine issues that need to be resolved.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, some modules such as bonding use proc_create
to create proc entries under /proc/net/, and other modules
such as ipv4 use proc_net_fops_create.
It looks a little chaos.this patch changes all of
proc_net_fops_create to proc_create. we can remove
proc_net_fops_create after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to now, the debug and info messages from the ipconfig subsytem
claim to display the IP address of the DHCP/BOOTP server but
display instead the IP address of the bootserver. Fix that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
adds a "hwaddr" to the "IP-Config: Complete" KERN_INFO message
with the dev_addr of the device selected for auto configuration.
Signed-off-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 5e953778a2 ("ipconfig: add nameserver
IPs to kernel-parameter ip=") introduces ic_nameservers_predef() that defined
only for BOOTP. However it is used by ip_auto_config_setup() as well. This
patch moves it outside of #ifdef BOOTP.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On small systems (e.g. embedded ones) IP addresses are often configured
by bootloaders and get assigned to kernel via parameter "ip=". If set to
"ip=dhcp", even nameserver entries from DHCP daemons are handled. These
entries exported in /proc/net/pnp are commonly linked by /etc/resolv.conf.
To configure nameservers for networks without DHCP, this patch adds option
<dns0-ip> and <dns1-ip> to kernel-parameter 'ip='.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __setup macro should follow the corresponding setup handler.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to delete the Token ring support. This removes any
special processing in the core networking for token ring, (aside
from net/tr.c itself), leaving the drivers and remaining tokenring
support present but inert.
The mass removal of the drivers and net/tr.c will be in a separate
commit, so that the history of these files that we still care
about won't have the giant deletion tied into their history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Standardize the net core ratelimited logging functions.
Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current kernel messaging style.
Convert a printk block to print_hex_dump.
Coalesce formats, align arguments.
Use %s, __func__ instead of embedding function names.
Some messages that were prefixed with <foo>_close are
now prefixed with <foo>_fini. Some ah4 and esp messages
are now not prefixed with "ip ".
The intent of this patch is to later add something like
#define pr_fmt(fmt) "IPv4: " fmt.
to standardize the output messages.
Text size is trivially reduced. (x86-32 allyesconfig)
$ size net/ipv4/built-in.o*
text data bss dec hex filename
887888 31558 249696 1169142 11d6f6 net/ipv4/built-in.o.new
887934 31558 249800 1169292 11d78c net/ipv4/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make C=2 CF="-D__CHECK_ENDIAN__" M=net
And fix flowi4_init_output() prototype for sport
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
previous commit 3fb72f1e6e
makes IP-Config wait for carrier on at least one network device.
Before waiting (predefined value 120s), check that at least one device
was successfully brought up. Otherwise (e.g. buggy bootloader
which does not set the MAC address) there is no point in waiting
for carrier.
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: Remove all uses of LL_ALLOCATED_SPACE
The macro LL_ALLOCATED_SPACE was ill-conceived. It applies the
alignment to the sum of needed_headroom and needed_tailroom. As
the amount that is then reserved for head room is needed_headroom
with alignment, this means that the tail room left may be too small.
This patch replaces all uses of LL_ALLOCATED_SPACE in net/ipv4
with the macro LL_RESERVED_SPACE and direct reference to
needed_tailroom.
This also fixes the problem with needed_headroom changing between
allocating the skb and reserving the head room.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
when dev_hard_header() failed, the newly allocated skb should be freed.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches
Al Viro
Alexey Dobriyan
Greg Kroah-Hartman
Johannes Berg
David S. Miller
Andrew Lunn
Mark Rutland
Linus Torvalds
Geert Uytterhoeven
Thierry Reding
Uwe Kleine-König
Ben Dooks
Arnd Bergmann
Bastian Stender
Li RongQing
Mugunthan V N
Ian Morris
Florian Fainelli
Fabian Frederick
Himangi Saraogi
FX Le Bail
Paul Gortmaker
Martin Fuzzey
Gao feng
Philippe De Muyter
Claudio Fontana
Andy Shevchenko
Christoph Fritz
Eldad Zack
Eric Dumazet
Gerlando Falauto
Herbert Xu