This fixes a problem where the mos7720 driver will make io to a device from
which it has been logically disconnected. It does so by introducing a flag by
which the generic usb serial code can signal the subdrivers their
disconnection and appropriate locking.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various small at91_udc cleanups:
- Use generic GPIO calls, not older platform-specific ones
- Use gpio_request()/gpio_free()
- Use VERBOSE_DEBUG convention, not older VERBOSE
- Fix sparse complaint about parameter type (changed to gfp_t)
- Add missing newline to some rarely-seen debug messages
- Fix some old cleanup bugs on probe() fault paths
Also add a mechanism whereby rm9200 gpios can drive the D+ pullup
through an inverting transistor, based on a patch from Steve Birtles.
Most UDC drivers supporting a GPIO based pullup should probably have
such an option, but testing it requries such a board in hand!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Steve Birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch exports two statistics to userspace:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration
connected_duration is the total time (in msec) that the device has
been connected. active_duration is the total time the device has not
been suspended. With these two statistics, tools like PowerTOP can
calculate the percentage time that a device is active, i.e. not
suspended or auto-suspended.
Users can also use the active_duration to check if a device is actually
autosuspended. Currently, they can set power/level to auto and
power/autosuspend to a positive timeout, but there's no way to know from
userspace if a device was actually autosuspended without looking at the
dmesg output. These statistics will be useful in creating an automated
userspace script to test autosuspend for USB devices.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some boards (like e.g. Tosa) invert the VBUS-detection signal:
it's low when a host is supplying VBUS, and high otherwise.
Allow specifying whether gpio_vbus value is inverted.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Given that none of the referenced header files test the proprocessor
conditional __KERNEL__, there's no point "unifdef"fing them.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a usb serial adapter is used as console, the usb serial console
driver bumps the open_count on the port struct used but doesn't attach
a real tty to it (only a fake one temporaly). If this port is opened later
using the regular character device interface, the open method won't
initialize the port, which is the expected, and will receive a brand new
tty struct created by tty layer, which will be stored in port->tty.
When the last close is issued, open_count won't be 0 because of the
console usage and the port->tty will still contain the old tty value. This
is the last ttyUSB<n> close so the allocated tty will be freed by the
tty layer. The usb_serial and usb_serial_port are still in use by the
console, so port_free() won't be called (serial_close() ->
usb_serial_put() -> destroy_serial() -> port_free()), so the scheduled
work (port->work, usb_serial_port_work()) will still run. And
usb_serial_port_work() does:
(...)
tty = port->tty;
if (!tty)
return;
tty_wakeup(tty);
which causes (manually copied):
Faulting instruction address: 0x6b6b6b68
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT PowerMac
Modules linked in: binfmt_misc ipv6 nfs lockd nfs_acl sunrpc dm_snapshot dm_mirror dm_mod hfsplus uinput ams input_polldev genrtc cpufreq_powersave i2c_powermac therm_adt746x snd_aoa_codec_tas snd_aoa_fabric_layout snd_aoa joydev snd_aoa_i2sbus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc pmac_zilog serial_core evdev ide_cd cdrom snd appletouch soundcore snd_aoa_soundbus bcm43xx firmware_class usbhid ieee80211softmac ff_memless firewire_ohci firewire_core ieee80211 ieee80211_crypt crc_itu_t sungem sungem_phy uninorth_agp agpart ssb
NIP: 6b6b6b68 LR: c01b2108 CTR: 6b6b6b6b
REGS: c106de80 TRAP: 0400 Not tainted (2.6.24-rc2)
MSR: 40009032 <EE,ME,IR,DR> CR: 82004024 XER: 00000000
TASK = c106b4c0[5] 'events/0' THREAD: c106c000
GPR00: 6b6b6b6b c106df30 c106b4c0 c2d613a0 00009032 00000001 00001a00 00000001
GPR08: 00000008 00000000 00000000 c106c000 42004028 00000000 016ffbe0 0171a724
GPR16: 016ffcf4 00240e24 00240e70 016fee68 016ff9a4 c03046c4 c0327f50 c03046fc
GPR24: c106b6b9 c106b4c0 c101d610 c106c000 c02160fc c1eac1dc c2d613ac c2d613a0
NIP [6b6b6b68] 0x6b6b6b68
LR [c01b2108] tty_wakeup+0x6c/0x9c
Call Trace:
[c106df30] [c01b20e8] tty_wakeup+0x4c/0x9c (unreliable)
[c106df40] [c0216138] usb_serial_port_work+0x3c/0x78
[c106df50] [c00432e8] run_workqueue+0xc4/0x15c
[c106df90] [c0043798] worker_thread+0xa0/0x124
[c106dfd0] [c0048224] kthread+0x48/0x84
[c106dff0] [c00129bc] kernel_thread+0x44/0x60
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Slab corruption: size-2048 start=c2d613a0, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c01b16d8>](release_one_tty+0xbc/0xf4)
050: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
Prev obj: start=c2d60b88, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c00f30ec>](show_stat+0x410/0x428)
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
This patch avoids this, clearing port->tty considering if the port is
used as serial console or not
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
G_PRINTER: Adds a USB printer gadget driver for use in printer firmware.
This adds a USB printer gadget driver for use in printer firmware.
The printer gadget channels data between the USB host and a userspace
program driving the print engine. The user space program reads and
writes the device file /dev/g_printer to receive or send printer data.
It can use ioctl calls to the device file to get or set printer status.
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1011) adds a #define for the newly-created Lockable
(i.e., password-protected) subclass 0x07 for USB mass-storage devices.
The private ISD200 entry (which had been mapped to subclass 0x07) is
moved to 0xf0, which is unlikely to conflict with any official
subclass designation.
The US_SC_MIN and US_SC_MAX constants aren't used anywhere, so the
patch removes them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert from class_device to device for drivers/usb/core.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: kill swap_io_context()
as-iosched: fix inconsistent ioc->lock context
ide-cd: fix leftover data BUG
block: make elevator lib checkpatch compliant
cfq-iosched: make checkpatch compliant
block: make core bits checkpatch compliant
block: new end request handling interface should take unsigned byte counts
unexport add_disk_randomness
block/sunvdc.c:print_version() must be __devinit
splice: always updated atime in direct splice
It blindly copies everything in the io_context, including the lock.
That doesn't work so well for either lock ordering or lockdep.
There seems zero point in swapping io contexts on a request to request
merge, so the best point of action is to just remove it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix problems with the 528x ColdFire CPU cache setup.
Do not cache the flash region (if present), and make the runtime
settings consistent with the init setting.
Problems pointed out by Bernd Buttner <b.buettner@mkc-gmbh.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The namespace is not available in the fib_sync_down_addr, add it as a
parameter.
Looking up a device by the pointer to it is OK. Looking up using a
result from fib_trie/fib_hash table lookup is also safe. No need to
fix that at all. So, just fix lookup by address and insertion to the
hash table path.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is required to make fib_info lookups namespace aware. In the
other case initial namespace devices are marked as dead in the local
routing table during other namespace stop.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_sync_down can be called with an address and with a device. In
reality it is called either with address OR with a device. The
codepath inside is completely different, so lets separate it into two
calls for these two cases.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new "flow" classifier, which is meant to extend the SFQ hashing
capabilities without hard-coding new hash functions and also allows
deterministic mappings of keys to classes, replacing some out of tree
iptables patches like IPCLASSIFY (maps IPs to classes), IPMARK (maps
IPs to marks, with fw filters to classes), ...
Some examples:
- Classic SFQ hash:
tc filter add ... flow hash \
keys src,dst,proto,proto-src,proto-dst divisor 1024
- Classic SFQ hash, but using information from conntrack to work properly in
combination with NAT:
tc filter add ... flow hash \
keys nfct-src,nfct-dst,proto,nfct-proto-src,nfct-proto-dst divisor 1024
- Map destination IPs of 192.168.0.0/24 to classids 1-257:
tc filter add ... flow map \
key dst addend -192.168.0.0 divisor 256
- alternatively:
tc filter add ... flow map \
key dst and 0xff
- similar, but reverse ordered:
tc filter add ... flow map \
key dst and 0xff xor 0xff
Perturbation is currently not supported because we can't reliable kill the
timer on destruction.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dumping statistics and make internal queues visible as
classes.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ipv4_devconf can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Outbound sequence number overflow error status
is counted as XfrmOutStateSeqError.
o Additionaly, it changes inbound sequence number replay
error name from XfrmInSeqOutOfWindow to XfrmInStateSeqError
to apply name scheme above.
o Inbound IPv4 UDP encapsuling type mismatch error is wrongly
mapped to XfrmInStateInvalid then this patch fiex the error
to XfrmInStateMismatch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ip route cache implementation is not suited to large caches.
We can consume a lot of CPU when cache must be invalidated, since we
currently need to evict all cache entries, and this eviction is
sometimes asynchronous. min_delay & max_delay can somewhat control this
asynchronism behavior, but whole thing is a kludge, regularly triggering
infamous soft lockup messages. When entries are still in use, this also
consumes a lot of ram, filling dst_garbage.list.
A better scheme is to use a generation identifier on each entry,
so that cache invalidation can be performed by changing the table
identifier, without having to scan all entries.
No more delayed flushing, no more stalling when secret_interval expires.
Invalidated entries will then be freed at GC time (controled by
ip_rt_gc_timeout or stress), or when an invalidated entry is found
in a chain when an insert is done.
Thus we keep a normal equilibrium.
This patch :
- renames rt_hash_rnd to rt_genid (and makes it an atomic_t)
- Adds a new rt_genid field to 'struct rtable' (filling a hole on 64bit)
- Checks entry->rt_genid at appropriate places :
Reuse the existing logic for multicast list synchronization for the
unicast address list. The core of dev_mc_sync/unsync are split out as
__dev_addr_sync/unsync and moved from dev_mcast.c to dev.c. These are
then used to implement dev_unicast_sync/unsync as well.
I'm working on cleaning up Intel's FCoE stack, which generates new MAC
addresses from the fibre channel device id assigned by the fabric as
per the current draft specification in T11. When using such a
protocol in a VLAN environment it would be nice to not always be
forced into promiscuous mode, assuming the underlying Ethernet driver
supports multiple unicast addresses as well.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Normally during a dump the key of the last dumped entry is used for
continuation, but since lock is dropped it might be lost. In that case
fallback to the old counter based N^2 behaviour. This means the dump
will end up skipping some routes which matches what FIB_HASH does.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a net argument to inet6_lookup and propagate it further.
Actually, this is tcp-v6 implementation of what was done for
tcp-v4 sockets in a previous patch.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a net argument to inet_lookup and propagate it further
into lookup calls. Plus tune the __inet_check_established.
The dccp and inet_diag, which use that lookup functions
pass the init_net into them.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tags the inet_bind_bucket struct with net pointer,
initializes it during creation and makes a filtering
during lookup.
A better hashfn, that takes the net into account is to
be done in the future, but currently all bind buckets
with similar port will be in one hash chain.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions are the same except for what they call
to "check_established" and "hash" for a socket.
This saves half-a-kilo for ipv4 and ipv6.
add/remove: 1/0 grow/shrink: 1/4 up/down: 582/-1128 (-546)
function old new delta
__inet_hash_connect - 577 +577
arp_ignore 108 113 +5
static.hint 8 4 -4
rt_worker_func 376 372 -4
inet6_hash_connect 584 25 -559
inet_hash_connect 586 25 -561
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have INET_MATCH, INET_TW_MATCH and INET6_MATCH to test sockets and
twbuckets for matching, but ipv6 twbuckets are tested manually.
Here's the INET6_TW_MATCH to help with it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Constify a few data tables use const qualifiers on variables where
possible in the nf_*_proto_tcp sources.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces the xt_hashlimit match revision 1. It adds support for
kernel-level inversion and grouping source and/or destination IP
addresses, allowing to limit on a per-subnet basis. While this would
technically obsolete xt_limit, xt_hashlimit is a more expensive due
to the hashbucketing.
Kernel-level inversion: Previously you had to do user-level inversion:
iptables -N foo
iptables -A foo -m hashlimit --hashlimit(-upto) 5/s -j RETURN
iptables -A foo -j DROP
iptables -A INPUT -j foo
now it is simpler:
iptables -A INPUT -m hashlimit --hashlimit-over 5/s -j DROP
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename all "conntrack" variables to "ct" for more consistency and
avoiding some overly long lines.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder struct nf_conntrack_l4proto so all members used during packet
processing are in the same cacheline.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_ct_tuple_src_equal() and nf_ct_tuple_dst_equal() both compare the protocol
numbers. Unfortunately gcc doesn't optimize out the second comparison, so
remove it and prefix both functions with __ to indicate that they should not
be used directly.
Saves another 16 byte of text in __nf_conntrack_find() on x86_64:
nf_conntrack_tuple_taken | -20 # 320 -> 300, size inlines: 181 -> 161
__nf_conntrack_find | -16 # 267 -> 251, size inlines: 127 -> 115
__nf_conntrack_confirm | -40 # 875 -> 835, size inlines: 570 -> 537
3 functions changed, 76 bytes removed
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignoring specific entries in __nf_conntrack_find() is only needed by NAT
for nf_conntrack_tuple_taken(). Remove it from __nf_conntrack_find()
and make nf_conntrack_tuple_taken() search the hash itself.
Saves 54 bytes of text in the hotpath on x86_64:
__nf_conntrack_find | -54 # 321 -> 267, # inlines: 3 -> 2, size inlines: 181 -> 127
nf_conntrack_tuple_taken | +305 # 15 -> 320, lexblocks: 0 -> 3, # inlines: 0 -> 3, size inlines: 0 -> 181
nf_conntrack_find_get | -2 # 90 -> 88
3 functions changed, 305 bytes added, 56 bytes removed, diff: +249
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the RCU conversion only write_lock usages of nf_conntrack_lock are
left (except one read_lock that should actually use write_lock in the
H.323 helper). Switch to a spinlock.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RCU for expectation hash. This doesn't buy much for conntrack
runtime performance, but allows to reduce the use of nf_conntrack_lock
for /proc and nf_netlink_conntrack.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHECK net/ipv4/netfilter/ip_tables.c
net/ipv4/netfilter/ip_tables.c:1453:8: warning: incorrect type in argument 3 (different signedness)
net/ipv4/netfilter/ip_tables.c:1453:8: expected int *size
net/ipv4/netfilter/ip_tables.c:1453:8: got unsigned int [usertype] *size
net/ipv4/netfilter/ip_tables.c:1458:44: warning: incorrect type in argument 3 (different signedness)
net/ipv4/netfilter/ip_tables.c:1458:44: expected int *size
net/ipv4/netfilter/ip_tables.c:1458:44: got unsigned int [usertype] *size
net/ipv4/netfilter/ip_tables.c:1603:2: warning: incorrect type in argument 2 (different signedness)
net/ipv4/netfilter/ip_tables.c:1603:2: expected unsigned int *i
net/ipv4/netfilter/ip_tables.c:1603:2: got int *<noident>
net/ipv4/netfilter/ip_tables.c:1627:8: warning: incorrect type in argument 3 (different signedness)
net/ipv4/netfilter/ip_tables.c:1627:8: expected int *size
net/ipv4/netfilter/ip_tables.c:1627:8: got unsigned int *size
net/ipv4/netfilter/ip_tables.c:1634:40: warning: incorrect type in argument 3 (different signedness)
net/ipv4/netfilter/ip_tables.c:1634:40: expected int *size
net/ipv4/netfilter/ip_tables.c:1634:40: got unsigned int *size
net/ipv4/netfilter/ip_tables.c:1653:8: warning: incorrect type in argument 5 (different signedness)
net/ipv4/netfilter/ip_tables.c:1653:8: expected unsigned int *i
net/ipv4/netfilter/ip_tables.c:1653:8: got int *<noident>
net/ipv4/netfilter/ip_tables.c:1666:2: warning: incorrect type in argument 2 (different signedness)
net/ipv4/netfilter/ip_tables.c:1666:2: expected unsigned int *i
net/ipv4/netfilter/ip_tables.c:1666:2: got int *<noident>
CHECK net/ipv4/netfilter/arp_tables.c
net/ipv4/netfilter/arp_tables.c:1285:40: warning: incorrect type in argument 3 (different signedness)
net/ipv4/netfilter/arp_tables.c:1285:40: expected int *size
net/ipv4/netfilter/arp_tables.c:1285:40: got unsigned int *size
net/ipv4/netfilter/arp_tables.c:1543:44: warning: incorrect type in argument 3 (different signedness)
net/ipv4/netfilter/arp_tables.c:1543:44: expected int *size
net/ipv4/netfilter/arp_tables.c:1543:44: got unsigned int [usertype] *size
CHECK net/ipv6/netfilter/ip6_tables.c
net/ipv6/netfilter/ip6_tables.c:1481:8: warning: incorrect type in argument 3 (different signedness)
net/ipv6/netfilter/ip6_tables.c:1481:8: expected int *size
net/ipv6/netfilter/ip6_tables.c:1481:8: got unsigned int [usertype] *size
net/ipv6/netfilter/ip6_tables.c:1486:44: warning: incorrect type in argument 3 (different signedness)
net/ipv6/netfilter/ip6_tables.c:1486:44: expected int *size
net/ipv6/netfilter/ip6_tables.c:1486:44: got unsigned int [usertype] *size
net/ipv6/netfilter/ip6_tables.c:1631:2: warning: incorrect type in argument 2 (different signedness)
net/ipv6/netfilter/ip6_tables.c:1631:2: expected unsigned int *i
net/ipv6/netfilter/ip6_tables.c:1631:2: got int *<noident>
net/ipv6/netfilter/ip6_tables.c:1655:8: warning: incorrect type in argument 3 (different signedness)
net/ipv6/netfilter/ip6_tables.c:1655:8: expected int *size
net/ipv6/netfilter/ip6_tables.c:1655:8: got unsigned int *size
net/ipv6/netfilter/ip6_tables.c:1662:40: warning: incorrect type in argument 3 (different signedness)
net/ipv6/netfilter/ip6_tables.c:1662:40: expected int *size
net/ipv6/netfilter/ip6_tables.c:1662:40: got unsigned int *size
net/ipv6/netfilter/ip6_tables.c:1680:8: warning: incorrect type in argument 5 (different signedness)
net/ipv6/netfilter/ip6_tables.c:1680:8: expected unsigned int *i
net/ipv6/netfilter/ip6_tables.c:1680:8: got int *<noident>
net/ipv6/netfilter/ip6_tables.c:1693:2: warning: incorrect type in argument 2 (different signedness)
net/ipv6/netfilter/ip6_tables.c:1693:2: expected unsigned int *i
net/ipv6/netfilter/ip6_tables.c:1693:2: got int *<noident>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hashtable size is really unsigned so sparse complains when you pass
a signed integer. Change all uses to make it consistent.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ranges to the new revision. This doesn't affect
compatibility since the new revision was not released yet.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman
Oliver Neukum
David Brownell
Sarah Sharp
Marcin Slusarz
Dmitry Baryshkov
Robert P. J. Day
Aristeu Rozanski
Craig W. Nadler
Alan Stern
Tony Jones
Linus Torvalds
Jens Axboe
Greg Ungerer
Denis V. Lunev
Patrick McHardy
Adrian Bunk
Masahide NAKAMURA
Eric Dumazet
Chris Leech
Stephen Hemminger
Pavel Emelyanov
Jan Engelhardt
Alexey Dobriyan