If there is an error here we should unlock in the caller (which is
imon_init_intf1()). We can remove this stray unlock.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a typo here. We meant to test "ir" instead of "props". The
"props" variable was tested earlier.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original condition is always false because ! has higher precedence
than == and neither 0 nor 1 is equal to IMON_DISPLAY_TYPE_VGA.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reverse HAS_BUTTON logic since most webcams either have a button or if
they don't don't bother to send any interrupts. However I have at least
one model that appears to leave the button GPIO floating and can send
a bogus interrupt.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_PRIORITY is also part of the ioctls that need to check the
access priority.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The detection of the saa711x often failed. Adding a small delay before
attempting to detect it fixed this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_register already sets intfdata, no need to do this again.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disconnecting the HDPVR caused a kernel oops if lockdep was enabled.
In addition, if an app still had video0 open and attempted to call ioctl
when the device was already disconnected the system would crash.
Move the freeing and cleanup code to the release function: that is the
right place for it since you know when you get there that nobody is
using the device.
Also removed usb_set_intfdata: v4l2_device_register sets this already
to v4l2_dev.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_register already sets the usb intfdata to v4l2_dev. So use
that instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No need to lock when unregistering the device: clear_bit is already an
atomic operation.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'type' field was undefined but should be set to ANALOG_TV.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If no signal or valid format is detected, then VIDIOC_QUERY_DV_PRESET must
return 0 and set the preset to V4L2_DV_INVALID.
This driver returned an error instead.
Also simplified the kernel messages a bit: change v4l2_err to v4l2_dbg (not
detecting a signal/valid format is not an error, so only print this info when
debug == 1) and do not call v4l_fill_dv_preset_info: it's overkill to do this
just for a debug message.
Thanks to Mats Randgaard for bringing this to my attention.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_prio_init/open/close returned an int when in fact they would
always return 0. Make these void functions.
v4l2_prio_close and v4l2_prio_check pass an enum v4l2_priority as a
pointer for no good reason. Replace with a normal enum v4l2_priority
argument.
These changes will simplify the work of moving priority handling into
the v4l core.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that s_fmt is no longer used for VBI format setup in subdevs, remove
the VBI support from s_fmt.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also removed the bogus zeroing of fmt.sliced when setting up raw VBI.
This should have been removed in ivtv, but it was just copied-and-pasted
into cx18.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also removed the bogus zeroing of fmt.sliced when setting up raw VBI.
Switching between raw and sliced VBI changed in 2.6.28 and this memset
should have been removed at that time. It was never noticed because
the bridge driver will fill in the fmt.vbi values anyway.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only a relatively small number of video receivers and transmitters actually
support VBI. So start moving the vbi specific ops to an ops struct of their
own.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control step values reported by the device are used as a divisor
unchecked, which can result in a division by zero.
Check the step value and make it 1 when null.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC relative controls (exposure time, iris, focus, zoom, pan/tilt)
are write-only (despite the UVC specification stating that the GET_CUR
request is mandatory). Mark the controls as such, and report the related
V4L2 controls V4L2_CTRL_FLAG_WRITE_ONLY.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Miricle 307K (17dc:0202) camera reports a 16-bit greyscale format,
support it in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vivi uses find_font(), which is only available when FONTS
is enabled, so make vivi depend on FONTS.
ERROR: "find_font" [drivers/media/video/vivi.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set correct GPIO number for BEHOLD_WANDER/VOYAGER
Add xc5000 callback function
Small rework tm6000_cards_setup function
Small rework tm6000_config_tuner, build mode_mask by config information
Rework for support xc5000 silicon tuner
Add some information messages for more better understand an errors.
[mchehab@redhat.com: Fix CodingStyle and merge conflicts]
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the V4L2 specification, poll() should set POLLOUT | POLLWRNORM
flags for output devices after the frame has been displayed.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_pages_to_sg() and videobuf_vmalloc_to_sg() happen to create
a scatterlist element for every page. However, this is not true for
bus addresses, so other functions shouldn't rely on the length of the
scatter list being equal to nr_pages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf-core checks if .sync ops is defined before calling.
So, we don't need a do-nothing function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While analyzing one of the videobuf patches, I noticed that
videobuf_dma_sync is only used internally inside videobuf-dma-sg.
So, let's remove this function, merging the code at __videobuf_dma_sync()
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For recoverable stream errors dqbuf() now returns 0 and the error flag
is set instead of returning EIO.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a patch to the cx25821-i2c.c file that fixes warning and errors found by checkpatch.pl tool
[mchehab@redhat.com: fix conflicts with changeset 2587a7ef7b8bc3c7db7c43659297b45b168922ab]
Signed-off-by: sai<tsg321@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes all the coding style issues reported by checkpatch.pl tool
Signed-off-by: sai <tsg321@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a patch to cx25821-alsa.c file that fixes of most of the
warning & errors found by checkpatch.pl tool
[mchehab@redhat.com: Fix conflicts with changeset 4e0c923a0d23f86c7331b32bc2aeb280e10e029e]
Signed-off-by: sai gopal <tsg321@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found that in gp8psk_load_bcm4500fw there is missing a check for
return value of kmalloc. Add one and bail out appropriatelly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch reduces static stack usage of one of the 2 top offenders
as listed by 'make checkstack':
Building with CONFIG_FRAME_WARN=2048 produces:
drivers/media/dvb/frontends/dib3000mc.c:853: warning: the frame size of 2224 bytes is larger than 2048 bytes
and in 'make checkstack', the stack usage goes from:
0x00000bbd dib3000mc_i2c_enumeration [dib3000mc]: 2232
to unlisted with this patch.
I don't have the hardware that is needed to test this patch.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter
Mats Randgaard
Brian Johnson
Hans Verkuil
Jean-François Moine
Laurent Pinchart
Randy Dunlap
Dmitri Belimov
Pawel Osciak
Arnout Vandecappelle
Mauro Carvalho Chehab
Ricardo Maraschini
sai
Jiri Slaby
Andrew Morton