Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Optimized support for Intel "Cluster-on-Die" (CoD) topologies (Dave
Hansen)
- Various sched/idle refinements for better idle handling (Nicolas
Pitre, Daniel Lezcano, Chuansheng Liu, Vincent Guittot)
- sched/numa updates and optimizations (Rik van Riel)
- sysbench speedup (Vincent Guittot)
- capacity calculation cleanups/refactoring (Vincent Guittot)
- Various cleanups to thread group iteration (Oleg Nesterov)
- Double-rq-lock removal optimization and various refactorings
(Kirill Tkhai)
- various sched/deadline fixes
... and lots of other changes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
sched/dl: Use dl_bw_of() under rcu_read_lock_sched()
sched/fair: Delete resched_cpu() from idle_balance()
sched, time: Fix build error with 64 bit cputime_t on 32 bit systems
sched: Improve sysbench performance by fixing spurious active migration
sched/x86: Fix up typo in topology detection
x86, sched: Add new topology for multi-NUMA-node CPUs
sched/rt: Use resched_curr() in task_tick_rt()
sched: Use rq->rd in sched_setaffinity() under RCU read lock
sched: cleanup: Rename 'out_unlock' to 'out_free_new_mask'
sched: Use dl_bw_of() under RCU read lock
sched/fair: Remove duplicate code from can_migrate_task()
sched, mips, ia64: Remove __ARCH_WANT_UNLOCKED_CTXSW
sched: print_rq(): Don't use tasklist_lock
sched: normalize_rt_tasks(): Don't use _irqsave for tasklist_lock, use task_rq_lock()
sched: Fix the task-group check in tg_has_rt_tasks()
sched/fair: Leverage the idle state info when choosing the "idlest" cpu
sched: Let the scheduler see CPU idle states
sched/deadline: Fix inter- exclusive cpusets migrations
sched/deadline: Clear dl_entity params when setscheduling to different class
sched/numa: Kill the wrong/dead TASK_DEAD check in task_numa_fault()
...
1. vma_policy_mof(task) is simply not safe unless task == current,
it can race with do_exit()->mpol_put(). Remove this arg and update
its single caller.
2. vma can not be NULL, remove this check and simplify the code.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We already reschedule env.dst_cpu in attach_tasks()->check_preempt_curr()
if this is necessary.
Furthermore, a higher priority class task may be current on dest rq,
we shouldn't disturb it.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Cc: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140930210441.5258.55054.stgit@localhost
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since commit caeb178c60 ("sched/fair: Make update_sd_pick_busiest() ...")
sd_pick_busiest returns a group that can be neither imbalanced nor overloaded
but is only more loaded than others. This change has been introduced to ensure
a better load balance in system that are not overloaded but as a side effect,
it can also generate useless active migration between groups.
Let take the example of 3 tasks on a quad cores system. We will always have an
idle core so the load balance will find a busiest group (core) whenever an ILB
is triggered and it will force an active migration (once above
nr_balance_failed threshold) so the idle core becomes busy but another core
will become idle. With the next ILB, the freshly idle core will try to pull the
task of a busy CPU.
The number of spurious active migration is not so huge in quad core system
because the ILB is not triggered so much. But it becomes significant as soon as
you have more than one sched_domain level like on a dual cluster of quad cores
where the ILB is triggered every tick when you have more than 1 busy_cpu
We need to ensure that the migration generate a real improveùent and will not
only move the avg_load imbalance on another CPU.
Before caeb178c60, the filtering of such use
case was ensured by the following test in f_b_g:
if ((local->idle_cpus < busiest->idle_cpus) &&
busiest->sum_nr_running <= busiest->group_weight)
This patch modified the condition to take into account situation where busiest
group is not overloaded: If the diff between the number of idle cpus in 2
groups is less than or equal to 1 and the busiest group is not overloaded,
moving a task will not improve the load balance but just move it.
A test with sysbench on a dual clusters of quad cores gives the following
results:
command: sysbench --test=cpu --num-threads=5 --max-time=5 run
The HZ is 200 which means that 1000 ticks has fired during the test.
With Mainline, perf gives the following figures:
Samples: 727 of event 'sched:sched_migrate_task'
Event count (approx.): 727
Overhead Command Shared Object Symbol
........ ............... ............. ..............
12.52% migration/1 [unknown] [.] 00000000
12.52% migration/5 [unknown] [.] 00000000
12.52% migration/7 [unknown] [.] 00000000
12.10% migration/6 [unknown] [.] 00000000
11.83% migration/0 [unknown] [.] 00000000
11.83% migration/3 [unknown] [.] 00000000
11.14% migration/4 [unknown] [.] 00000000
10.87% migration/2 [unknown] [.] 00000000
2.75% sysbench [unknown] [.] 00000000
0.83% swapper [unknown] [.] 00000000
0.55% ktps65090charge [unknown] [.] 00000000
0.41% mmcqd/1 [unknown] [.] 00000000
0.14% perf [unknown] [.] 00000000
With this patch, perf gives the following figures
Samples: 20 of event 'sched:sched_migrate_task'
Event count (approx.): 20
Overhead Command Shared Object Symbol
........ ............... ............. ..............
80.00% sysbench [unknown] [.] 00000000
10.00% swapper [unknown] [.] 00000000
5.00% ktps65090charge [unknown] [.] 00000000
5.00% migration/1 [unknown] [.] 00000000
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1412170735-5356-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The code in find_idlest_cpu() looks for the CPU with the smallest load.
However, if multiple CPUs are idle, the first idle CPU is selected
irrespective of the depth of its idle state.
Among the idle CPUs we should pick the one with with the shallowest idle
state, or the latest to have gone idle if all idle CPUs are in the same
state. The later applies even when cpuidle is configured out.
This patch doesn't cover the following issues:
- The idle exit latency of a CPU might be larger than the time needed
to migrate the waking task to an already running CPU with sufficient
capacity, and therefore performance would benefit from task packing
in such case (in most cases task packing is about power saving).
- Some idle states have a non negligible and non abortable entry latency
which needs to run to completion before the exit latency can start.
A concurrent patch series is making this info available to the cpuidle
core. Once available, the entry latency with the idle timestamp could
determine when the exit latency may be effective.
Those issues will be handled in due course. In the mean time, what
is implemented here should improve things already compared to the current
state of affairs.
Based on an initial patch from Daniel Lezcano.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-pm@vger.kernel.org
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/n/tip-@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
current->state == TASK_DEAD means that the task is doing its
last schedule(), page fault is obviously impossible at this
stage.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140921194743.GA30114@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
'capacity_orig' is only changed for systems with an SMT sched_domain level in order
to reflect the lower capacity of CPUs. Heterogenous systems also have to reflect an
original capacity that is different from the default value.
Create a more generic function arch_scale_cpu_capacity that can be also used by
non SMT platforms to set capacity_orig.
The __weak implementation of arch_scale_cpu_capacity() is the previous SMT variant,
in order to keep backward compatibility with the use of capacity_orig.
arch_scale_smt_capacity() and default_scale_smt_capacity() have been removed as
they were not used elsewhere than in arch_scale_cpu_capacity().
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Reviewed-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
[ Added default_scale_cpu_capacity() back. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: riel@redhat.com
Cc: Morten.Rasmussen@arm.com
Cc: efault@gmx.de
Cc: nicolas.pitre@linaro.org
Cc: daniel.lezcano@linaro.org
Cc: dietmar.eggemann@arm.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1409051215-16788-5-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In wake_affine() I have tried to understand the meaning of the condition:
(this_load <= load &&
this_load + target_load(prev_cpu, idx) <= tl_per_task)
but I failed to find a use case that can take advantage of it and I haven't
found clear description in the previous commit's log.
Futhermore, the comment of the condition refers to the task_hot function that
was used before being replaced by the current condition:
/*
* This domain has SD_WAKE_AFFINE and
* p is cache cold in this domain, and
* there is no bad imbalance.
*/
If we look more deeply the below condition:
this_load + target_load(prev_cpu, idx) <= tl_per_task
When sync is clear, we have:
tl_per_task = runnable_load_avg / nr_running
this_load = max(runnable_load_avg, cpuload[idx])
target_load = max(runnable_load_avg', cpuload'[idx])
It implies that runnable_load_avg == 0 and nr_running <= 1 in order to match the
condition. This implies that runnable_load_avg == 0 too because of the
condition: this_load <= load.
but if this _load is null, 'balanced' is already set and the test is redundant.
If sync is set, it's not as straight forward as above (especially if cgroup
are involved) but the policy should be similar as we have removed a task that's
going to sleep in order to get a more accurate load and this_load values.
The current conclusion is that these additional condition don't give any benefit
so we can remove them.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: preeti@linux.vnet.ibm.com
Cc: riel@redhat.com
Cc: Morten.Rasmussen@arm.com
Cc: efault@gmx.de
Cc: nicolas.pitre@linaro.org
Cc: daniel.lezcano@linaro.org
Cc: dietmar.eggemann@arm.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1409051215-16788-3-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The imbalance flag can stay set whereas there is no imbalance.
Let assume that we have 3 tasks that run on a dual cores /dual cluster system.
We will have some idle load balance which are triggered during tick.
Unfortunately, the tick is also used to queue background work so we can reach
the situation where short work has been queued on a CPU which already runs a
task. The load balance will detect this imbalance (2 tasks on 1 CPU and an idle
CPU) and will try to pull the waiting task on the idle CPU. The waiting task is
a worker thread that is pinned on a CPU so an imbalance due to pinned task is
detected and the imbalance flag is set.
Then, we will not be able to clear the flag because we have at most 1 task on
each CPU but the imbalance flag will trig to useless active load balance
between the idle CPU and the busy CPU.
We need to reset of the imbalance flag as soon as we have reached a balanced
state. If all tasks are pinned, we don't consider that as a balanced state and
let the imbalance flag set.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: riel@redhat.com
Cc: Morten.Rasmussen@arm.com
Cc: efault@gmx.de
Cc: nicolas.pitre@linaro.org
Cc: daniel.lezcano@linaro.org
Cc: dietmar.eggemann@arm.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1409051215-16788-2-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
new_cpu is reassigned below, so we do not need this here.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1410529276.3569.24.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The code in task_numa_compare() will only examine at most one idle CPU per node,
because they all have the same score. However, some idle CPUs are better
candidates than others, due to busy or idle SMT siblings, etc...
The scheduler has logic to find the best CPU within an LLC to place a
task. The NUMA code should probably use it.
This seems to reduce the standard deviation for single instance SPECjbb2005
with a low warehouse count on my 4 node test system.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: mgorman@suse.de
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140904163530.189d410a@cuia.bos.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When running workloads on 2+ socket systems, based on perf profiles, the
update_cfs_rq_blocked_load() function often shows up as taking up a
noticeable % of run time.
Much of the contention is in __update_cfs_rq_tg_load_contrib() when we
update the tg load contribution stats. However, it turns out that in many
cases, they don't need to be updated and "tg_contrib" is 0.
This patch adds a check in __update_cfs_rq_tg_load_contrib() to skip updating
tg load contribution stats when nothing needs to be updated. This reduces the
cacheline contention that would be unnecessary.
Reviewed-by: Ben Segall <bsegall@google.com>
Reviewed-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Jason Low <jason.low2@hp.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Turner <pjt@google.com>
Cc: jason.low2@hp.com
Cc: Yuyang Du <yuyang.du@intel.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1409643684.19197.15.camel@j-VirtualBox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
An overrun could happen in function start_hrtick_dl()
when a task with SCHED_DEADLINE runs in the microseconds
range.
For example, if a task with SCHED_DEADLINE has the following parameters:
Task runtime deadline period
P1 200us 500us 500us
The deadline and period from task P1 are less than 1ms.
In order to achieve microsecond precision, we need to enable HRTICK feature
by the next command:
PC#echo "HRTICK" > /sys/kernel/debug/sched_features
PC#trace-cmd record -e sched_switch &
PC#./schedtool -E -t 200000:500000:500000 -e ./test
The binary test is in an endless while(1) loop here.
Some pieces of trace.dat are as follows:
<idle>-0 157.603157: sched_switch: :R ==> 2481:4294967295: test
test-2481 157.603203: sched_switch: 2481:R ==> 0:120: swapper/2
<idle>-0 157.605657: sched_switch: :R ==> 2481:4294967295: test
test-2481 157.608183: sched_switch: 2481:R ==> 2483:120: trace-cmd
trace-cmd-2483 157.609656: sched_switch:2483:R==>2481:4294967295: test
We can get the runtime of P1 from the information above:
runtime = 157.608183 - 157.605657
runtime = 0.002526(2.526ms)
The correct runtime should be less than or equal to 200us at some point.
The problem is caused by a conditional judgment "delta > 10000"
in function start_hrtick_dl().
Because no hrtimer start up to control the rest of runtime
when the reset of runtime is less than 10us.
So the process will continue to run until tick-period is coming.
Move the code with the limit of the least time slice
from hrtick_start_fair() to hrtick_start() because the
EDF schedule class also needs this function in start_hrtick_dl().
To fix this problem, we call hrtimer_start() unconditionally in
start_hrtick_dl(), and make sure the scheduling slice won't be smaller
than 10us in hrtimer_start().
Signed-off-by: Xiaofeng Yan <xiaofeng.yan@huawei.com>
Reviewed-by: Li Zefan <lizefan@huawei.com>
Acked-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1409022941-5880-1-git-send-email-xiaofeng.yan@huawei.com
[ Massaged the changelog and the code. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: paulmck@linux.vnet.ibm.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140822145043.GA580@ada
Signed-off-by: Ingo Molnar <mingo@kernel.org>
__get_cpu_var can paper over differences in the definitions of
cpumask_var_t and either use the address of the cpumask variable
directly or perform a fetch of the address of the struct cpumask
allocated elsewhere. This is important particularly when using per cpu
cpumask_var_t declarations because in one case we have an offset into
a per cpu area to handle and in the other case we need to fetch a
pointer from the offset.
This patch introduces a new macro
this_cpu_cpumask_var_ptr()
that is defined where cpumask_var_t is defined and performs the proper
actions. All use cases where __get_cpu_var is used with cpumask_var_t
are converted to the use of this_cpu_cpumask_var_ptr().
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Avoid double_rq_lock() and use TASK_ON_RQ_MIGRATING for
load_balance(). The advantage is (obviously) not holding two
rq->lock's at the same time and thereby increasing parallelism.
Further note that if there was no task to migrate we will not
have acquired the second rq->lock at all.
The important point to note is that because we acquire dst->lock
immediately after releasing src->lock the potential wait time of
task_rq_lock() callers on TASK_ON_RQ_MIGRATING is not longer
than it would have been in the double rq lock scenario.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Turner <pjt@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Kirill Tkhai <tkhai@yandex.ru>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1408528109.23412.94.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Avoid double_rq_lock() and use the TASK_ON_RQ_MIGRATING state for
active_load_balance_cpu_stop(). The advantage is (obviously) not
holding two 'rq->lock's at the same time and thereby increasing
parallelism.
Further note that if there was no task to migrate we will not
have acquired the second rq->lock at all.
The important point to note is that because we acquire dst->lock
immediately after releasing src->lock the potential wait time of
task_rq_lock() callers on TASK_ON_RQ_MIGRATING is not longer
than it would have been in the double rq lock scenario.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Turner <pjt@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Kirill Tkhai <tkhai@yandex.ru>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1408528081.23412.92.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implement task_on_rq_queued() and use it everywhere instead of
on_rq check. No functional changes.
The only exception is we do not use the wrapper in
check_for_tasks(), because it requires to export
task_on_rq_queued() in global header files. Next patch in series
would return it back, so we do not twist it from here to there.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Turner <pjt@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Kirill Tkhai <tkhai@yandex.ru>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1408528052.23412.87.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
(sched_entity::on_rq == 1) does not guarantee the task is pickable;
changes on throttled cfs_rq must not lead to reschedule.
Check for task_struct::on_rq instead.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1407312361.8424.35.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit a43455a1d5 ensures that
task_numa_migrate will call task_numa_compare on the preferred
node all the time, even when the preferred node has no free capacity.
This could lead to a performance regression if nr_running == capacity
on both the source and the destination node. This can be avoided by
also checking for nr_running == capacity on the source node, which is
one stricter than checking .has_free_capacity.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: mgorman@suse.de
Cc: vincent.guittot@linaro.org
Cc: Morten.Rasmussen@arm.com
Cc: nicolas.pitre@linaro.org
Cc: efault@gmx.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1407173008-9334-2-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Allow calculate_imbalance() to 'create' idle cpus in the busiest group
if there are idle cpus in the local group.
Suggested-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140729152705.GX12054@laptop.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently update_sd_pick_busiest only identifies the busiest sd
that is either overloaded, or has a group imbalance. When no
sd is imbalanced or overloaded, the load balancer fails to find
the busiest domain.
This breaks load balancing between domains that are not overloaded,
in the !SD_ASYM_PACKING case. This patch makes update_sd_pick_busiest
return true when the busiest sd yet is encountered.
Groups are ranked in the order overloaded > imbalanced > other,
with higher ranked groups getting priority even when their load
is lower. This is necessary due to the possibility of unequal
capacities and cpumasks between domains within a sched group.
Behaviour for SD_ASYM_PACKING does not seem to match the comment,
but I have no hardware to test that so I have left the behaviour
of that code unchanged.
Enum for group classification suggested by Peter Zijlstra.
Signed-off-by: Rik van Riel <riel@redhat.com>
[peterz: replaced sg_lb_stats::group_imb with the new enum group_type
in an attempt to avoid endless recalculation]
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Cc: ktkhai@parallels.com
Cc: tim.c.chen@linux.intel.com
Cc: nicolas.pitre@linaro.org
Cc: jhladky@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140729152743.GI3935@laptop
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rik noticed that calculate_imbalance() relies on
update_sd_pick_busiest() to guarantee that busiest->sum_nr_running >
busiest->group_capacity_factor.
Break this implicit assumption (with the intent of not providing it
anymore) by having calculat_imbalance() verify it and not rely on
others.
Reported-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20140729152631.GW12054@laptop.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fix following warning caused by missing description
"overload" in kernel/sched/fair.c
Warning(.//kernel/sched/fair.c:5906): No description found for
parameter 'overload'
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1406518686-7274-1-git-send-email-standby24x7@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Due to divergent trees, Rik find that this patch is no longer
required.
Requested-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-u6odkgkw8wz3m7orgsjfo5pi@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We always use resched_task() with rq->curr argument.
It's not possible to reschedule any task but rq's current.
The patch introduces resched_curr(struct rq *) to
replace all of the repeating patterns. The main aim
is cleanup, but there is a little size profit too:
(before)
$ size kernel/sched/built-in.o
text data bss dec hex filename
155274 16445 7042 178761 2ba49 kernel/sched/built-in.o
$ size vmlinux
text data bss dec hex filename
7411490 1178376 991232 9581098 92322a vmlinux
(after)
$ size kernel/sched/built-in.o
text data bss dec hex filename
155130 16445 7042 178617 2b9b9 kernel/sched/built-in.o
$ size vmlinux
text data bss dec hex filename
7411362 1178376 991232 9580970 9231aa vmlinux
I was choosing between resched_curr() and resched_rq(),
and the first name looks better for me.
A little lie in Documentation/trace/ftrace.txt. I have not
actually collected the tracing again. With a hope the patch
won't make execution times much worse :)
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20140628200219.1778.18735.stgit@localhost
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We kill rq->rd on the CPU_DOWN_PREPARE stage:
cpuset_cpu_inactive -> cpuset_update_active_cpus -> partition_sched_domains ->
-> cpu_attach_domain -> rq_attach_root -> set_rq_offline
This unthrottles all throttled cfs_rqs.
But the cpu is still able to call schedule() till
take_cpu_down->__cpu_disable()
is called from stop_machine.
This case the tasks from just unthrottled cfs_rqs are pickable
in a standard scheduler way, and they are picked by dying cpu.
The cfs_rqs becomes throttled again, and migrate_tasks()
in migration_call skips their tasks (one more unthrottle
in migrate_tasks()->CPU_DYING does not happen, because rq->rd
is already NULL).
Patch sets runtime_enabled to zero. This guarantees, the runtime
is not accounted, and the cfs_rqs won't exceed given
cfs_rq->runtime_remaining = 1, and tasks will be pickable
in migrate_tasks(). runtime_enabled is recalculated again
when rq becomes online again.
Ben Segall also noticed, we always enable runtime in
tg_set_cfs_bandwidth(). Actually, we should do that for online
cpus only. To prevent races with unthrottle_offline_cfs_rqs()
we take get_online_cpus() lock.
Reviewed-by: Ben Segall <bsegall@google.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
CC: Konstantin Khorenko <khorenko@parallels.com>
CC: Paul Turner <pjt@google.com>
CC: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403684382.3462.42.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reading through the scan period code and comment, it appears the
intent was to slow down NUMA scanning when a majority of accesses
are on the local node, specifically a local:remote ratio of 3:1.
However, the code actually tests local / (local + remote), and
the actual cut-off point was around 30% local accesses, well before
a task has actually converged on a node.
Changing the threshold to 7 means scanning slows down when a task
has around 70% of its accesses local, which appears to match the
intent of the code more closely.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: mgorman@suse.de
Cc: chegu_vinod@hp.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403538095-31256-8-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up the best node setting in task_numa_migrate() to deal with a task
in a pseudo-interleaved NUMA group, which is already running in the
best location.
Set the task's preferred nid to the current nid, so task migration is
not retried at a high rate.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: mgorman@suse.de
Cc: chegu_vinod@hp.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403538095-31256-7-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Running "perf bench numa mem -0 -m -P 1000 -p 8 -t 20" on a 4
node system results in 160 runnable threads on a system with 80
CPU threads.
Once a process has nearly converged, with 39 threads on one node
and 1 thread on another node, the remaining thread will be unable
to migrate to its preferred node through a task swap.
However, a simple task move would make the workload converge,
witout causing an imbalance.
Test for this unlikely occurrence, and attempt a task move to
the preferred nid when it happens.
# Running main, "perf bench numa mem -p 8 -t 20 -0 -m -P 1000"
###
# 160 tasks will execute (on 4 nodes, 80 CPUs):
# -1x 0MB global shared mem operations
# -1x 1000MB process shared mem operations
# -1x 0MB thread local mem operations
###
###
#
# 0.0% [0.2 mins] 0/0 1/1 36/2 0/0 [36/3 ] l: 0-0 ( 0) {0-2}
# 0.0% [0.3 mins] 43/3 37/2 39/2 41/3 [ 6/10] l: 0-1 ( 1) {1-2}
# 0.0% [0.4 mins] 42/3 38/2 40/2 40/2 [ 4/9 ] l: 1-2 ( 1) [50.0%] {1-2}
# 0.0% [0.6 mins] 41/3 39/2 40/2 40/2 [ 2/9 ] l: 2-4 ( 2) [50.0%] {1-2}
# 0.0% [0.7 mins] 40/2 40/2 40/2 40/2 [ 0/8 ] l: 3-5 ( 2) [40.0%] ( 41.8s converged)
Without this patch, this same perf bench numa mem run had to
rely on the scheduler load balancer to first balance out the
load (moving a random task), before a task swap could complete
the NUMA convergence.
The load balancer does not normally take action unless the load
difference exceeds 25%. Convergence times of over half an hour
have been observed without this patch.
With this patch, the NUMA balancing code will simply migrate the
task, if that does not cause an imbalance.
Also skip examining a CPU in detail if the improvement on that CPU
is no more than the best we already have.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: chegu_vinod@hp.com
Cc: mgorman@suse.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-ggthh0rnh0yua6o5o3p6cr1o@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When a task is part of a numa_group, the comparison should always use
the group weight, in order to make workloads converge.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: chegu_vinod@hp.com
Cc: mgorman@suse.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403538378-31571-4-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When CONFIG_FAIR_GROUP_SCHED is enabled, the load that a task places
on a CPU is determined by the group the task is in. The active groups
on the source and destination CPU can be different, resulting in a
different load contribution by the same task at its source and at its
destination. As a result, the load needs to be calculated separately
for each CPU, instead of estimated once with task_h_load().
Getting this calculation right allows some workloads to converge,
where previously the last thread could get stuck on another node,
without being able to migrate to its final destination.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: mgorman@suse.de
Cc: chegu_vinod@hp.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403538378-31571-3-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently the NUMA code scales the load on each node with the
amount of CPU power available on that node, but it does not
apply any adjustment to the load of the task that is being
moved over.
On systems with SMT/HT, this results in a task being weighed
much more heavily than a CPU core, and a task move that would
even out the load between nodes being disallowed.
The correct thing is to apply the power correction to the
numbers after we have first applied the move of the tasks'
loads to them.
This also allows us to do the power correction with a multiplication,
rather than a division.
Also drop two function arguments for load_too_unbalanced, since it
takes various factors from env already.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: chegu_vinod@hp.com
Cc: mgorman@suse.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403538378-31571-2-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
From task_numa_placement, always try to consolidate the tasks
in a group on the group's top nid.
In case this task is part of a group that is interleaved over
multiple nodes, task_numa_migrate will set the task's preferred
nid to the best node it could find for the task, so this patch
will cause at most one run through task_numa_migrate.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: mgorman@suse.de
Cc: chegu_vinod@hp.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403538095-31256-2-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When a system is lightly loaded (i.e. no more than 1 job per cpu),
attempt to pull job to a cpu before putting it to idle is unnecessary and
can be skipped. This patch adds an indicator so the scheduler can know
when there's no more than 1 active job is on any CPU in the system to
skip needless job pulls.
On a 4 socket machine with a request/response kind of workload from
clients, we saw about 0.13 msec delay when we go through a full load
balance to try pull job from all the other cpus. While 0.1 msec was
spent on processing the request and generating a response, the 0.13 msec
load balance overhead was actually more than the actual work being done.
This overhead can be skipped much of the time for lightly loaded systems.
With this patch, we tested with a netperf request/response workload that
has the server busy with half the cpus in a 4 socket system. We found
the patch eliminated 75% of the load balance attempts before idling a cpu.
The overhead of setting/clearing the indicator is low as we already gather
the necessary info while we call add_nr_running() and update_sd_lb_stats.()
We switch to full load balance load immediately if any cpu got more than
one job on its run queue in add_nr_running. We'll clear the indicator
to avoid load balance when we detect no cpu's have more than one job
when we scan the work queues in update_sg_lb_stats(). We are aggressive
in turning on the load balance and opportunistic in skipping the load
balance.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Jason Low <jason.low2@hp.com>
Cc: "Paul E.McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403551009.2970.613.camel@schen9-DESK
Signed-off-by: Ingo Molnar <mingo@kernel.org>
distribute_cfs_runtime() intentionally only hands out enough runtime to
bring each cfs_rq to 1 ns of runtime, expecting the cfs_rqs to then take
the runtime they need only once they actually get to run. However, if
they get to run sufficiently quickly, the period timer is still in
distribute_cfs_runtime() and no runtime is available, causing them to
throttle. Then distribute has to handle them again, and this can go on
until distribute has handed out all of the runtime 1ns at a time, which
takes far too long.
Instead allow access to the same runtime that distribute is handing out,
accepting that corner cases with very low quota may be able to spend the
entire cfs_b->runtime during distribute_cfs_runtime, meaning that the
runtime directly handed out by distribute_cfs_runtime was over quota. In
addition, if a cfs_rq does manage to throttle like this, make sure the
existing distribute_cfs_runtime no longer loops over it again.
Signed-off-by: Ben Segall <bsegall@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140620222120.13814.21652.stgit@sword-of-the-dawn.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When computing cache hot, we should check if the migration dst cpu is idle,
instead of the current cpu. Though they are same in normal balancing, that
is false nowadays in nohz idle balancing at least.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mike Galbraith <mgalbraith@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140607090452.4696E301D2@webmail.sinamail.sina.com.cn
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is possible that at task_numa_placement() time, the task's
numa_preferred_nid does not change, but the task is not
actually running on the preferred node at the time.
In that case, we still want to attempt migration to the
preferred node.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: mgorman@suse.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140604163315.1dbc7b56@cuia.bos.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The first thing task_numa_migrate() does is check to see if there is
CPU capacity available on the preferred node, in order to move the
task there.
However, if the preferred node is all busy, we would skip considering
that node for tasks swaps in the subsequent loop. This prevents NUMA
convergence of tasks on busy systems.
However, swapping locations with a task on our preferred nid, when
the preferred nid is busy, is perfectly fine.
The fix is to also look for a CPU on our preferred nid when it is
totally busy.
This changes "perf bench numa mem -p 4 -t 20 -m -0 -P 1000" from
not converging in 15 minutes on my 4 node system, to converging in
10-20 seconds.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: mgorman@suse.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140604160942.6969b101@cuia.bos.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull more scheduler updates from Ingo Molnar:
"Second round of scheduler changes:
- try-to-wakeup and IPI reduction speedups, from Andy Lutomirski
- continued power scheduling cleanups and refactorings, from Nicolas
Pitre
- misc fixes and enhancements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Delete extraneous extern for to_ratio()
sched/idle: Optimize try-to-wake-up IPI
sched/idle: Simplify wake_up_idle_cpu()
sched/idle: Clear polling before descheduling the idle thread
sched, trace: Add a tracepoint for IPI-less remote wakeups
cpuidle: Set polling in poll_idle
sched: Remove redundant assignment to "rt_rq" in update_curr_rt(...)
sched: Rename capacity related flags
sched: Final power vs. capacity cleanups
sched: Remove remaining dubious usage of "power"
sched: Let 'struct sched_group_power' care about CPU capacity
sched/fair: Disambiguate existing/remaining "capacity" usage
sched/fair: Change "has_capacity" to "has_free_capacity"
sched/fair: Remove "power" from 'struct numa_stats'
sched: Fix signedness bug in yield_to()
sched/fair: Use time_after() in record_wakee()
sched/balancing: Reduce the rate of needless idle load balancing
sched/fair: Fix unlocked reads of some cfs_b->quota/period
This function is supposed to return true if the new load imbalance is
worse than the old one. It didn't. I can only hope brown paper bags
are in style.
Now things converge much better on both the 4 node and 8 node systems.
I am not sure why this did not seem to impact specjbb performance on the
4 node system, which is the system I have full-time access to.
This bug was introduced recently, with commit e63da03639 ("sched/numa:
Allow task switch if load imbalance improves")
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
It is better not to think about compute capacity as being equivalent
to "CPU power". The upcoming "power aware" scheduler work may create
confusion with the notion of energy consumption if "power" is used too
liberally.
Let's rename the following feature flags since they do relate to capacity:
SD_SHARE_CPUPOWER -> SD_SHARE_CPUCAPACITY
ARCH_POWER -> ARCH_CAPACITY
NONTASK_POWER -> NONTASK_CAPACITY
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linaro-kernel@lists.linaro.org
Cc: Andy Fleming <afleming@freescale.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/n/tip-e93lpnxb87owfievqatey6b5@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is better not to think about compute capacity as being equivalent
to "CPU power". The upcoming "power aware" scheduler work may create
confusion with the notion of energy consumption if "power" is used too
liberally.
This contains the architecture visible changes. Incidentally, only ARM
takes advantage of the available pow^H^H^Hcapacity scaling hooks and
therefore those changes outside kernel/sched/ are confined to one ARM
specific file. The default arch_scale_smt_power() hook is not overridden
by anyone.
Replacements are as follows:
arch_scale_freq_power --> arch_scale_freq_capacity
arch_scale_smt_power --> arch_scale_smt_capacity
SCHED_POWER_SCALE --> SCHED_CAPACITY_SCALE
SCHED_POWER_SHIFT --> SCHED_CAPACITY_SHIFT
The local usage of "power" in arch/arm/kernel/topology.c is also changed
to "capacity" as appropriate.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linaro-kernel@lists.linaro.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Brown <broonie@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/n/tip-48zba9qbznvglwelgq2cfygh@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds
Oleg Nesterov
Kirill Tkhai
Vincent Guittot
Nicolas Pitre
Zhihui Zhang
Rik van Riel
Jason Low
xiaofeng.yan
Andreea-Cristina Bernat
Christoph Lameter
Peter Zijlstra
Masanari Iida
Kirill Tkhai
Tim Chen
Ben Segall
Hillf Danton