* clk-qcom-sdm845:
clk: qcom: Export clk_fabia_pll_configure()
clk: qcom: Add video clock controller driver for SDM845
dt-bindings: clock: Introduce QCOM Video clock bindings
clk: qcom: Add Global Clock controller (GCC) driver for SDM845
clk: qcom: Add DT bindings for SDM845 gcc clock controller
clk: qcom: Configure the RCGs to a safe source as needed
clk: qcom: Add support for BRANCH_HALT_SKIP flag for branch clocks
clk: qcom: Simplify gdsc status checking logic
clk: qcom: gdsc: Add support to poll CFG register to check GDSC state
clk: qcom: gdsc: Add support to poll for higher timeout value
clk: qcom: gdsc: Add support to reset AON and block reset logic
clk: qcom: Add support for controlling Fabia PLL
clk: qcom: Clear hardware clock control bit of RCG
Also fixup the Kconfig mess where SDM845 GCC has msm8998 in the
description and also the video Kconfig says things slightly differently
from the GCC one so just make it the same.
_freq_tbl_determine_rate uses the pre_div found in the clock plan
multiplied by the requested rate from the caller to determine the
best parent rate to set. If the requested rate is not exactly equal
to the rate that was found in the clock plan, then using the requested
rate in parent rate calculations is incorrect. For instance, if 150MHz
was requested, but 200MHz was the match found, and that plan had a
pre_div of 3, then the parent should be set to 600MHz, not 450MHz.
Signed-off-by: Evan Green <evgreen@chromium.org>
Fixes: bcd61c0f53 ("clk: qcom: Add support for root clock generators (RCGs)")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For some root clock generators, there could be child branches which are
controlled by an entity other than application processor subsystem. For
such RCGs, as per application processor subsystem clock driver, all of
its downstream clocks are disabled and RCG is in disabled state but in
reality downstream clocks can be left enabled before.
So in this scenario, when RCG is disabled as per clock driver's point of
view and when rate scaling request comes before downstream clock enable
request, then RCG fails to update its configuration because in reality
RCG is on and it expects its new source to already be in enable state but
in reality new source is off. In order to avoid having the RCG to go into
an invalid state, add support to update the CFG, M, N and D registers
during set_rate() without configuration update and defer the actual RCG
configuration update to be done during clk_enable() as at this point of
time, both its new parent and safe source will be already enabled and RCG
can safely switch to new parent.
During clk_disable() request, configure it to safe source as both its
parents, safe source and current parent will be enabled and RCG can
safely execute a switch.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For upcoming targets like sdm845, POR value of the hardware clock control
bit is set for most of root clocks which needs to be cleared for software
to be able to control. For older targets like MSM8996, this bit is reserved
bit and having POR value as 0 so this patch will work for the older targets
too. So update the configuration mask to take care of the same to clear
hardware clock control bit.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The RCGs ops for shared branches are not used now, so remove it.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The default behaviour with clk_rcg2_ops is for the
clk_round_rate()/clk_set_rate() to return/set a ceil clock
rate closest to the requested rate by looking up the corresponding
frequency table.
However, we do have some instances (mainly sdcc on various platforms)
of clients expecting a clk_set_rate() to set a floor value instead.
Add a new clk_rcg2_floor_ops to handle this for such specific
rcg instances
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The GPU clocks on msm8996 have three dedicated PLLs, MMPLL2,
MMPLL8, and MMPLL9. We leave MMPLL9 at the maximum speed (624
MHz), and we use MMPLL2 and MMPLL8 for the other frequencies. To
make switching frequencies faster, we ping-pong between MMPLL2
and MMPLL8 when we're switching between frequencies that aren't
the maximum. Implement custom rcg clk ops for this type of
frequency switching.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some root clock generators may have child branches that are controlled
by different CPUs. These RCGs require some special operations:
- some enable bits have to be toggled when we set the rate;
- if RCG is disabled we only cache the rate and set it later when enabled;
- when the RCG is disabled, the mux is set to the safe source;
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
[sboyd@codeaurora.org: Simplify recalc_rate implementation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sometimes the display driver may want to change the parent PLL of
the display clocks (byte and pixel clocks) depending on the
use-case. Currently the parent is fixed by means of having a
frequency table with one entry that chooses a particular parent.
Remove this restriction and use the parent the clock is
configured for in the hardware during clk_set_rate(). This
requires consumers to rely on the default parent or to configure
the parent with clk_set_parent()/assigned-clock-parents on the
clocks before calling clk_set_rate().
Tested-by: Archit Taneja <architt@codeaurora.org>
Cc: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mostly converted with the following snippet:
@@
struct clk_hw *E;
@@
-__clk_get_flags(E->clk)
+clk_hw_get_flags(E)
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock rates are stored in an unsigned long field, but ->determine_rate()
(which returns a rounded rate from a requested one) returns a long
value (errors are reported using negative error codes), which can lead
to long overflow if the clock rate exceed 2Ghz.
Change ->determine_rate() prototype to return 0 or an error code, and pass
a pointer to a clk_rate_request structure containing the expected target
rate and the rate constraints imposed by clk users.
The clk_rate_request structure might be extended in the future to contain
other kind of constraints like the rounding policy, the maximum clock
inaccuracy or other things that are not yet supported by the CCF
(power consumption constraints ?).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: "Emilio López" <emilio@elopez.com.ar>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
CC: Peter De Schrijver <pdeschrijver@nvidia.com>
CC: Prashant Gaikwad <pgaikwad@nvidia.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-doc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-omap@vger.kernel.org
CC: linux-mips@linux-mips.org
CC: linux-tegra@vger.kernel.org
[sboyd@codeaurora.org: Fix parent dereference problem in
__clk_determine_rate()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@codeaurora.org: Folded in fix from Heiko for fixed-rate
clocks without parents or a rate determining op]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since the parent rate has been recalculated, pixel RCG clock
should rely on it to find the correct M/N values during set_rate,
instead of calling __clk_round_rate() to its parent again.
Signed-off-by: Hai Li <hali@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Fixes: 99cbd064b0 ("clk: qcom: Support display RCG clocks")
[sboyd@codeaurora.org: Silenced unused parent variable warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When we introduced the parent_map tables, we missed to update
some of the functions where mapping is translated. Fix this.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the current parent mapping code, we can get duplicate or inconsistent
indexes, which leads to discrepancy between the number of elements in the
array and the number of parents. Until now, this was solved with some
reordering but this is not always possible.
This patch introduces index tables that are used to define the relations
between the PLL source and the hardware mux configuration value.
To accomplish this, here we do the following:
- Define a parent_map struct to map the relations between PLL source index
and register configuration value.
- Add a qcom_find_src_index() function for finding the index of a clock
matching the specific PLL configuration.
- Update the {set,get}_parent RCG functions use the newly introduced
parent_map struct.
- Convert all existing drivers to the new parent_map tables.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
According to the common clock framework API, the clk_get_parent() function
should return u8. Currently we are returning negative values on error. Fix
this and use the default parent in case of an error.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, a RCG's M/N counter (used for fraction division) is
set to either 'bypass' (counter disabled) or 'dual edge' (counter
enabled) based on whether the corresponding rcg struct has a mnd
field specified and a non-zero N.
In the case where M and N are the same value, the M/N counter is
still enabled by code even though no division takes place.
Leaving the RCG in such a state can result in improper behavior.
This was observed with the DSI pixel clock RCG when M and N were
both set to 1.
Add an additional check (M != N) to enable the M/N counter only
when it's needed for fraction division.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Fixes: bcd61c0f53 (clk: qcom: Add support for root clock
generators (RCGs))
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.
Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
migrated clk-private.h changes to clk.c]
This is in preparation for clock providers to not have to deal with struct clk.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
There are two find_freq() functions in clk-rcg.c and clk-rcg2.c
that are almost exactly the same. Consolidate them into one
function to save on some code space.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the DSI/EDP/HDMI RCG clocks. With the proper
display driver in place this should allow us to support display
clocks on msm8974 based devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some drivers may want to call clk_set_rate() with a very large
number to force the clock to go as fast as it possibly can
without having to know the range between the highest rate and
second highest rate. Add support for this by defaulting to the
highest rate in the frequency table if we can't find a frequency
greater than what is requested.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If the bit is set the clock is off so we should be checking for
a clear bit, not a set bit. Invert the logic.
Fixes: bcd61c0f53 (clk: qcom: Add support for root clock generators (RCGs))
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for the root clock generators on Qualcomm devices.
RCGs are highly customizable mux/divider/counter clocks that can
be used to generate almost any rate desired given some input
source that is faster than the desired rate.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Stephen Boyd
Evan Green
Amit Nischal
Georgi Djakov
Rajendra Nayak
Stephen Boyd
Boris Brezillon
Hai Li
Archit Taneja
Tomeu Vizoso