slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A peer (or local user) may cause TCP to use a nominal MSS of as little
as 88 (actual MSS of 76 with timestamps). Given that we have a
sufficiently prodigious local sender and the peer ACKs quickly enough,
it is nevertheless possible to grow the window for such a connection
to the point that we will try to send just under 64K at once. This
results in a single skb that expands to 861 segments.
In some drivers with TSO support, such an skb will require hundreds of
DMA descriptors; a substantial fraction of a TX ring or even more than
a full ring. The TX queue selected for the skb may stall and trigger
the TX watchdog repeatedly (since the problem skb will be retried
after the TX reset). This particularly affects sfc, for which the
issue is designated as CVE-2012-3412.
Therefore:
1. Add the field net_device::gso_max_segs holding the device-specific
limit.
2. In netif_skb_features(), if the number of segments is too high then
mask out GSO features to force fall back to software GSO.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netif_copy_real_num_queues() the return value of
netif_set_real_num_tx_queues() should be checked.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most multi-queue networking driver consider the number of online cpus when
configuring RSS queues.
This patch adds a wrapper to the number of cpus, setting an upper limit on the
number of cpus a driver should consider (by default) when allocating resources
for his queues.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dev_loopback_xmit() in order to deduplicate functions
ip_dev_loopback_xmit() (in net/ipv4/ip_output.c) and
ip6_dev_loopback_xmit() (in net/ipv6/ip6_output.c).
I was about to reinvent the wheel when I noticed that
ip_dev_loopback_xmit() and ip6_dev_loopback_xmit() do exactly what I
need and are not IP-only functions, but they were not available to reuse
elsewhere.
ip6_dev_loopback_xmit() does not have line "skb_dst_force(skb);", but I
understand that this is harmless, and should be in dev_loopback_xmit().
Signed-off-by: Michel Machado <michel@digirati.com.br>
CC: "David S. Miller" <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_get_by_name() is slow because pm_qos_req has been inserted between
name[] and name_hlist, adding cache misses.
pm_qos_req has nothing to do at the beginning of struct net_device
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make netif_dbg use dynamic debugging whenever
CONFIG_DYNAMIC_DEBUG is enabled.
commit b558c96ffa
("dynamic_debug: make dynamic-debug supersede DEBUG ccflag")
missed updating the netif_dbg variant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8a83a00b07.
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
Conflicts:
drivers/net/macvlan.c
net/8021q/vlan_dev.c
net/core/dev.c
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO can check if skb to be merged has its skb->head mapped to a page
fragment, instead of a kmalloc() area.
We 'upgrade' skb->head as a fragment in itself
This avoids the frag_list fallback, and permits to build true GRO skb
(one sk_buff and up to 16 fragments), using less memory.
This reduces number of cache misses when user makes its copy, since a
single sk_buff is fetched.
This is a followup of patch "net: allow skb->head to be a page fragment"
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a dev_uc_add_excl() and dev_mc_add_excl() calls
similar to the original dev_{uc|mc}_add() except it sets
the global bit and returns -EEXIST for duplicat entires.
This is useful for drivers that support SR-IOV, macvlan
devices and any other devices that need to manage the
unicast and multicast lists.
v2: fix typo UNICAST should be MULTICAST in dev_mc_add_excl()
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds two new flags NTF_MASTER and NTF_SELF that can
now be used to specify where PF_BRIDGE netlink commands should
be sent. NTF_MASTER sends the commands to the 'dev->master'
device for parsing. Typically this will be the linux net/bridge,
or open-vswitch devices. Also without any flags set the command
will be handled by the master device as well so that current user
space tools continue to work as expected.
The NTF_SELF flag will push the PF_BRIDGE commands to the
device. In the basic example below the commands are then parsed
and programmed in the embedded bridge.
Note if both NTF_SELF and NTF_MASTER bits are set then the
command will be sent to both 'dev->master' and 'dev' this allows
user space to easily keep the embedded bridge and software bridge
in sync.
There is a slight complication in the case with both flags set
when an error occurs. To resolve this the rtnl handler clears
the NTF_ flag in the netlink ack to indicate which sets completed
successfully. The add/del handlers will abort as soon as any
error occurs.
To support this new net device ops were added to call into
the device and the existing bridging code was refactored
to use these. There should be no required changes in user space
to support the current bridge behavior.
A basic setup with a SR-IOV enabled NIC looks like this,
veth0 veth2
| |
------------
| bridge0 | <---- software bridging
------------
/
/
ethx.y ethx
VF PF
\ \ <---- propagate FDB entries to HW
\ \
--------------------
| Embedded Bridge | <---- hardware offloaded switching
--------------------
In this case the embedded bridge must be managed to allow 'veth0'
to communicate with 'ethx.y' correctly. At present drivers managing
the embedded bridge either send frames onto the network which
then get dropped by the switch OR the embedded bridge will flood
these frames. With this patch we have a mechanism to manage the
embedded bridge correctly from user space. This example is specific
to SR-IOV but replacing the VF with another PF or dropping this
into the DSA framework generates similar management issues.
Examples session using the 'br'[1] tool to add, dump and then
delete a mac address with a new "embedded" option and enabled
ixgbe driver:
# br fdb add 22:35:19:ac:60:59 dev eth3
# br fdb
port mac addr flags
veth0 22:35:19:ac:60:58 static
veth0 9a:5f:81:f7:f6:ec local
eth3 00:1b:21:55:23:59 local
eth3 22:35:19:ac:60:59 static
veth0 22:35:19:ac:60:57 static
#br fdb add 22:35:19:ac:60:59 embedded dev eth3
#br fdb
port mac addr flags
veth0 22:35:19:ac:60:58 static
veth0 9a:5f:81:f7:f6:ec local
eth3 00:1b:21:55:23:59 local
eth3 22:35:19:ac:60:59 static
veth0 22:35:19:ac:60:57 static
eth3 22:35:19:ac:60:59 local embedded
#br fdb del 22:35:19:ac:60:59 embedded dev eth3
I added a couple lines to 'br' to set the flags correctly is all. It
is my opinion that the merit of this patch is now embedded and SW
bridges can both be modeled correctly in user space using very nearly
the same message passing.
[1] 'br' tool was published as an RFC here and will be renamed 'bridge'
http://patchwork.ozlabs.org/patch/117664/
Thanks to Jamal Hadi Salim, Stephen Hemminger and Ben Hutchings for
valuable feedback, suggestions, and review.
v2: fixed api descriptions and error case with both NTF_SELF and
NTF_MASTER set plus updated patch description.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f04565ddf5 (dev: use name hash for dev_seq_ops) added a second
regression, as some devices are missing from /proc/net/dev if many
devices are defined.
When seq_file buffer is filled, the last ->next/show() method is
canceled (pos value is reverted to value prior ->next() call)
Problem is after above commit, we dont restart the lookup at right
position in ->start() method.
Fix this by removing the internal 'pos' pointer added in commit, since
we need to use the 'loff_t *pos' provided by seq_file layer.
This also reverts commit 5cac98dd0 (net: Fix corruption
in /proc/*/net/dev_mcast), since its not needed anymore.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Mihai Maruseac <mmaruseac@ixiacom.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
https://lkml.org/lkml/2012/3/4/159
--
Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then
one to delete the device.h includes from the linux/include/ dir
wherever possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3j4+
-----END PGP SIGNATURE-----
Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/device.h> avoidance patches from Paul Gortmaker:
"Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then one
to delete the device.h includes from the linux/include/ dir wherever
possible."
* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
device.h: audit and cleanup users in main include dir
device.h: cleanup users outside of linux/include (C files)
"[RFC - PATCH 0/7] consolidation of BUG support code."
https://lkml.org/lkml/2012/1/26/525
--
The changes shown here are to unify linux's BUG support under
the one <linux/bug.h> file. Due to historical reasons, we have
some BUG code in bug.h and some in kernel.h -- i.e. the support for
BUILD_BUG in linux/kernel.h predates the addition of linux/bug.h,
but old code in kernel.h wasn't moved to bug.h at that time. As
a band-aid, kernel.h was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions.
Here is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.]
Ugh - very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and
hence relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2.
But to ensure that git history for bisect doesn't get needless
build failures introduced, the commits have been reorderd to fix
the problem areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PYQT
-----END PGP SIGNATURE-----
Merge tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/bug.h> cleanup from Paul Gortmaker:
"The changes shown here are to unify linux's BUG support under the one
<linux/bug.h> file. Due to historical reasons, we have some BUG code
in bug.h and some in kernel.h -- i.e. the support for BUILD_BUG in
linux/kernel.h predates the addition of linux/bug.h, but old code in
kernel.h wasn't moved to bug.h at that time. As a band-aid, kernel.h
was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions. Here
is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.] Ugh -
very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and hence
relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2. But
to ensure that git history for bisect doesn't get needless build
failures introduced, the commits have been reorderd to fix the problem
areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414"
Fix up conflicts (new radeon file, reiserfs header cleanups) as per Paul
and linux-next.
* tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
kernel.h: doesn't explicitly use bug.h, so don't include it.
bug: consolidate BUILD_BUG_ON with other bug code
BUG: headers with BUG/BUG_ON etc. need linux/bug.h
bug.h: add include of it to various implicit C users
lib: fix implicit users of kernel.h for TAINT_WARN
spinlock: macroize assert_spin_locked to avoid bug.h dependency
x86: relocate get/set debugreg fcns to include/asm/debugreg.
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink breakage
reverted), dynamic debugging updates, w1 drivers, hyperv driver updates,
and a variety of other bits and pieces, full information in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9neCsACgkQMUfUDdst+ylyQwCfY2eizvzw5HhjQs8gOiBRDADe
yrgAnj1Zan2QkoCnQIFJNAoxqNX9yAhd
=biH6
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches for 3.4-rc1 from Greg KH:
"Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink
breakage reverted), dynamic debugging updates, w1 drivers, hyperv
driver updates, and a variety of other bits and pieces, full
information in the shortlog."
* tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (78 commits)
Tools: hv: Support enumeration from all the pools
Tools: hv: Fully support the new KVP verbs in the user level daemon
Drivers: hv: Support the newly introduced KVP messages in the driver
Drivers: hv: Add new message types to enhance KVP
regulator: Support driver probe deferral
Revert "sysfs: Kill nlink counting."
uevent: send events in correct order according to seqnum (v3)
driver core: minor comment formatting cleanups
driver core: move the deferred probe pointer into the private area
drivercore: Add driver probe deferral mechanism
DS2781 Maxim Stand-Alone Fuel Gauge battery and w1 slave drivers
w1_bq27000: Only one thread can access the bq27000 at a time.
w1_bq27000 - remove w1_bq27000_write
w1_bq27000: remove unnecessary NULL test.
sysfs: Fix memory leak in sysfs_sd_setsecdata().
intel_idle: Revert change of auto_demotion_disable_flags for Nehalem
w1: Fix w1_bq27000
driver-core: documentation: fix up Greg's email address
powernow-k6: Really enable auto-loading
powernow-k7: Fix CPU family number
...
This is related to fixing the bug of dropping FCoE frames when disabling tx ip
checksum by 'ethtool -K ethx tx off'. The FCoE protocol stack driver would
use CHECKSUM_UNNECESSARY on tx path instead of CHECKSUM_PARTIAL (as indicated in
the 2/2 of this series). To do so, netif_needs_gso() has to be changed here to
not do gso for both CHECKSUM_PARTIAL and CHECKSUM_UNNECESSARY.
Ref. to original discussion thread:
http://patchwork.ozlabs.org/patch/146567/
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The <linux/device.h> header includes a lot of stuff, and
it in turn gets a lot of use just for the basic "struct device"
which appears so often.
Clean up the users as follows:
1) For those headers only needing "struct device" as a pointer
in fcn args, replace the include with exactly that.
2) For headers not really using anything from device.h, simply
delete the include altogether.
3) For headers relying on getting device.h implicitly before
being included themselves, now explicitly include device.h
4) For files in which doing #1 or #2 uncovers an implicit
dependency on some other header, fix by explicitly adding
the required header(s).
Any C files that were implicitly relying on device.h to be
present have already been dealt with in advance.
Total removals from #1 and #2: 51. Total additions coming
from #3: 9. Total other implicit dependencies from #4: 7.
As of 3.3-rc1, there were 110, so a net removal of 42 gives
about a 38% reduction in device.h presence in include/*
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This change adds a memory barrier to the byte queue limit code to address a
possible race as has been seen in the past with the
netif_stop_queue/netif_wake_queue logic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are seeing dev_watchdog hangs on several drivers. I suspect this is due
to the __QUEUE_STATE_STACK_XOFF bit being set prior to a reset for link
change, and then not being cleared by netdev_tx_reset_queue. This change
corrects that.
In addition we were seeing dev_watchdog hangs on igb after running the
ethtool tests. We found this to be due to the fact that the ethtool test
runs the same logic as ndo_start_xmit, but we were never clearing the XOFF
flag since the loopback test in ethtool does not do byte queue accounting.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Specifically use it in napi_disable_pending(), napi_schedule_prep(),
napi_reschedule(), netif_tx_queue_stopped(), netif_queue_stopped(),
netif_xmit_stopped(), netif_xmit_frozen_or_stopped(), netif_running(),
__netif_subqueue_stopped(), netif_subqueue_stopped(),
netif_is_multiquue(), netif_carrier_ok(), netif_dormant(),
netif_oper_up(), netif_device_present(), __netif_tx_trylock(),
net_gso_ok(), skb_gso_ok(), netif_needs_gso(), and
netif_is_bond_slave().
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers use internal netdev stats member to store part of their
stats, yet advertize ndo_get_stats64() to implement some 64bit fields.
Allow them to use netdev_stats_to_stats64() helper to make the copy of
netdev stats before they compute their 64bit counters.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a header file is making use of BUG, BUG_ON, BUILD_BUG_ON, or any
other BUG variant in a static inline (i.e. not in a #define) then
that header really should be including <linux/bug.h> and not just
expecting it to be implicitly present.
We can make this change risk-free, since if the files using these
headers didn't have exposure to linux/bug.h already, they would have
been causing compile failures/warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is useful for testing RX handling of frames with bad
CRCs.
Requires driver support to actually put the packet on the
wire properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
So here's a boot tested patch on top of Jason's series that does
all the cleanups I talked about and turns jump labels into a
more intuitive to use facility. It should also address the
various misconceptions and confusions that surround jump labels.
Typical usage scenarios:
#include <linux/static_key.h>
struct static_key key = STATIC_KEY_INIT_TRUE;
if (static_key_false(&key))
do unlikely code
else
do likely code
Or:
if (static_key_true(&key))
do likely code
else
do unlikely code
The static key is modified via:
static_key_slow_inc(&key);
...
static_key_slow_dec(&key);
The 'slow' prefix makes it abundantly clear that this is an
expensive operation.
I've updated all in-kernel code to use this everywhere. Note
that I (intentionally) have not pushed through the rename
blindly through to the lowest levels: the actual jump-label
patching arch facility should be named like that, so we want to
decouple jump labels from the static-key facility a bit.
On non-jump-label enabled architectures static keys default to
likely()/unlikely() branches.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jason Baron <jbaron@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: a.p.zijlstra@chello.nl
Cc: mathieu.desnoyers@efficios.com
Cc: davem@davemloft.net
Cc: ddaney.cavm@gmail.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20120222085809.GA26397@elte.hu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If CONFIG_DYNAMIC_DEBUG is defined, honor it over DEBUG, so that
pr_debug()s are controllable, instead of always-on. When DEBUG is
also defined, change _DPRINTK_FLAGS_DEFAULT to enable printing by
default.
Also adding _DPRINTK_FLAGS_INCL_MODNAME would be nice, but there are
numerous cases of pr_debug(NAME ": ...), which would result in double
printing of module-name. So defer this until things settle.
Cc: David Miller <davem@davemloft.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
igmp: Avoid zero delay when receiving odd mixture of IGMP queries
netdev: make net_device_ops const
bcm63xx: make ethtool_ops const
usbnet: make ethtool_ops const
net: Fix build with INET disabled.
net: introduce netif_addr_lock_nested() and call if when appropriate
net: correct lock name in dev_[uc/mc]_sync documentations.
net: sk_update_clone is only used in net/core/sock.c
8139cp: fix missing napi_gro_flush.
pktgen: set correct max and min in pktgen_setup_inject()
smsc911x: Unconditionally include linux/smscphy.h in smsc911x.h
asix: fix infinite loop in rx_fixup()
net: Default UDP and UNIX diag to 'n'.
r6040: fix typo in use of MCR0 register bits
net: fix sock_clone reference mismatch with tcp memcontrol
* 'for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Remove irqsafe_cpu_xxx variants
Fix up conflict in arch/x86/include/asm/percpu.h due to clash with
cebef5beed ("x86: Fix and improve percpu_cmpxchg{8,16}b_double()")
which edited the (now removed) irqsafe_cpu_cmpxchg*_double code.
dev_uc_sync() and dev_mc_sync() are acquiring netif_addr_lock for
destination device of synchronization. Since netif_addr_lock is
already held at the time for source device, this triggers lockdep
deadlock warning.
There's no way this deadlock can happen so use spin_lock_nested() to
silence the warning.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a new ndo_get_fcoe_hbainfo() call in
net_device_ops for FCoE protocol stack.
If supported by the underlying device, the FCoE protocol
stack will call this to get device specific information
from the underlying device.
This information will then be utilized by the FCoE protocol
stack to register Fiber Channel HBA attributes with the
Fiber Channel Management Service via Fabric Device
Management Interface (FDMI) as per the T11 FC-GS
specification.
Changes in v2:
- As per comments from David Miller aligning the parameters
of the ndo_get_fcoe_hbainfo()
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aim of this patch is to provide full range of rps_flow_cnt on 64bit arches.
Theorical limit on number of flows is 2^32
Fix some buggy RPS/RFS macros as well.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
CC: Xi Wang <xi.wang@gmail.com>
CC: Laurent Chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
-tj: This is part of on-going percpu API cleanup. For detailed
discussion of the subject, please refer to the following thread.
http://thread.gmane.org/gmane.linux.kernel/1222078
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <alpine.DEB.2.00.1112221154380.11787@router.home>
This reverts commit 5c3ddec73d.
S390 qeth driver actually still uses the setup ops.
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's simpler to just keep these things out until there is a real user
of them, so we can see what the needs actually are, rather than keep
these things around as useless overhead.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to keep track of vids needed to be in rx vlan filters of
devices even if they are used in bond/team etc.
vlan_info as well as vlan_group previously was, is allocated when first
vid is added and dealocated whan last vid is deleted.
vlan_group definition is moved to private header.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->neigh_priv_len records the private area length.
This will trigger for neigh_table objects which set tbl->entry_size
to zero, and the first instances of this will be forthcoming.
Signed-off-by: David S. Miller <davem@davemloft.net>
Networking stack support for byte queue limits, uses dynamic queue
limits library. Byte queue limits are maintained per transmit queue,
and a dql structure has been added to netdev_queue structure for this
purpose.
Configuration of bql is in the tx-<n> sysfs directory for the queue
under the byte_queue_limits directory. Configuration includes:
limit_min, bql minimum limit
limit_max, bql maximum limit
hold_time, bql slack hold time
Also under the directory are:
limit, current byte limit
inflight, current number of bytes on the queue
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add interfaces for drivers to call for recording number of packets and
bytes at send time and transmit completion. Also, added a function to
"reset" a queue. These will be used by Byte Queue Limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create separate queue state flags so that either the stack or drivers
can turn on XOFF. Added a set of functions used in the stack to determine
if a queue is really stopped (either by stack or driver)
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I just hit this during my testing. Isn't there another bug lurking?
BUG kmalloc-8: Redzone overwritten
INFO: 0xc0000000de9dec48-0xc0000000de9dec4b. First byte 0x0 instead of 0xcc
INFO: Allocated in .__seq_open_private+0x30/0xa0 age=0 cpu=5 pid=3896
.__kmalloc+0x1e0/0x2d0
.__seq_open_private+0x30/0xa0
.seq_open_net+0x60/0xe0
.dev_mc_seq_open+0x4c/0x70
.proc_reg_open+0xd8/0x260
.__dentry_open.clone.11+0x2b8/0x400
.do_last+0xf4/0x950
.path_openat+0xf8/0x480
.do_filp_open+0x48/0xc0
.do_sys_open+0x140/0x250
syscall_exit+0x0/0x40
dev_mc_seq_ops uses dev_seq_start/next/stop but only allocates
sizeof(struct seq_net_private) of private data, whereas it expects
sizeof(struct dev_iter_state):
struct dev_iter_state {
struct seq_net_private p;
unsigned int pos; /* bucket << BUCKET_SPACE + offset */
};
Create dev_seq_open_ops and use it so we don't have to expose
struct dev_iter_state.
[ Problem added by commit f04565ddf5 (dev: use name hash for
dev_seq_ops) -Eric ]
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang
Ben Hutchings
Jiri Pirko
Yuval Mintz
Michel Machado
Eric Dumazet
Joe Perches
David S. Miller
John Fastabend
Eric Dumazet
Linus Torvalds
Yi Zou
Paul Gortmaker
Alexander Duyck
Ben Greear
Ingo Molnar
Jim Cromie
Jiri Pirko
Neerav Parikh
Christoph Lameter
Tom Herbert
Anton Blanchard
Ben Hutchings