Let the inode verifier do it's work by returning an error when we
fail to find correct magic numbers in an inode buffer.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
This is the recovery side of the btree block owner change operation
performed by swapext on CRC enabled filesystems. We detect that an
owner change is needed by the flag that has been placed on the inode
log format flag field. Because the inode recovery is being replayed
after the buffers that make up the BMBT in the given checkpoint, we
can walk all the buffers and directly modify them when we see the
flag set on an inode.
Because the inode can be relogged and hence present in multiple
chekpoints with the "change owner" flag set, we could do multiple
passes across the inode to do this change. While this isn't optimal,
we can't directly ignore the flag as there may be multiple
independent swap extent operations being replayed on the same inode
in different checkpoints so we can't ignore them.
Further, because the owner change operation uses ordered buffers, we
might have buffers that are newer on disk than the current
checkpoint and so already have the owner changed in them. Hence we
cannot just peek at a buffer in the tree and check that it has the
correct owner and assume that the change was completed.
So, for the moment just brute force the owner change every time we
see an inode with the flag set. Note that we have to be careful here
because the owner of the buffers may point to either the old owner
or the new owner. Currently the verifier can't verify the owner
directly, so there is no failure case here right now. If we verify
the owner exactly in future, then we'll have to take this into
account.
This was tested in terms of normal operation via xfstests - all of
the fsr tests now pass without failure. however, we really need to
modify xfs/227 to stress v3 inodes correctly to ensure we fully
cover this case for v5 filesystems.
In terms of recovery testing, I used a hacked version of xfs_fsr
that held the temp inode open for a few seconds before exiting so
that the filesystem could be shut down with an open owner change
recovery flags set on at least the temp inode. fsr leaves the temp
inode unlinked and in btree format, so this was necessary for the
owner change to be reliably replayed.
logprint confirmed the tmp inode in the log had the correct flag set:
INO: cnt:3 total:3 a:0x69e9e0 len:56 a:0x69ea20 len:176 a:0x69eae0 len:88
INODE: #regs:3 ino:0x44 flags:0x209 dsize:88
^^^^^
0x200 is set, indicating a data fork owner change needed to be
replayed on inode 0x44. A printk in the revoery code confirmed that
the inode change was recovered:
XFS (vdc): Mounting Filesystem
XFS (vdc): Starting recovery (logdev: internal)
recovering owner change ino 0x44
XFS (vdc): Version 5 superblock detected. This kernel L support enabled!
Use of these features in this kernel is at your own risk!
XFS (vdc): Ending recovery (logdev: internal)
The script used to test this was:
$ cat ./recovery-fsr.sh
#!/bin/bash
dev=/dev/vdc
mntpt=/mnt/scratch
testfile=$mntpt/testfile
umount $mntpt
mkfs.xfs -f -m crc=1 $dev
mount $dev $mntpt
chmod 777 $mntpt
for i in `seq 10000 -1 0`; do
xfs_io -f -d -c "pwrite $(($i * 4096)) 4096" $testfile > /dev/null 2>&1
done
xfs_bmap -vp $testfile |head -20
xfs_fsr -d -v $testfile &
sleep 10
/home/dave/src/xfstests-dev/src/godown -f $mntpt
wait
umount $mntpt
xfs_logprint -t $dev |tail -20
time mount $dev $mntpt
xfs_bmap -vp $testfile
umount $mntpt
$
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
CRC enabled filesystems fail log recovery with 100% reliability on
xfstests xfs/085 with the following failure:
XFS (vdb): Mounting Filesystem
XFS (vdb): Starting recovery (logdev: internal)
XFS (vdb): Corruption detected. Unmount and run xfs_repair
XFS (vdb): bad inode magic/vsn daddr 144 #0 (magic=0)
XFS: Assertion failed: 0, file: fs/xfs/xfs_inode_buf.c, line: 95
The problem is that the inode buffer has not been recovered before
the readahead on the inode buffer is issued. The checkpoint being
recovered actually allocates the inode chunk we are doing readahead
from, so what comes from disk during readahead is essentially
random and the verifier barfs on it.
This inode buffer readahead problem affects non-crc filesystems,
too, but xfstests does not trigger it at all on such
configurations....
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The only thing remaining in xfs_inode.[ch] are the operations that
read, write or verify physical inodes in their underlying buffers.
Move all this code to xfs_inode_buf.[ch] and so we can stop sharing
xfs_inode.[ch] with userspace.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Dave Chinner