The read and writes from the fifo are from a buffer, with various
fields and data at predefined offsets. So, they should not be done to
the same address(or port) in case of val_count greater than 1.
Therefore, fix this by using iowrite32()/ioread32() instead of
ioread32_rep()/iowrite32_rep().
Also, the write into FIFO must be performed with an offset from the
message ram base address. Therefore, fix the base address to
mram_base.
Fixes: e39381770e ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20210920123344.2320-1-a-govindraju@ti.com
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the driver was not opened, rcar_can_suspend() should not call
clk_disable() because the clock was not enabled.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Link: https://lore.kernel.org/all/20210924075556.223685-1-yoshihiro.shimoda.uh@renesas.com
Cc: stable@vger.kernel.org
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Ayumi Nakamichi <ayumi.nakamichi.kf@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When isotp_sendmsg() concurrent, tx.state of all TX processes can be
ISOTP_IDLE. The conditions so->tx.state != ISOTP_IDLE and
wq_has_sleeper(&so->wait) can not protect TX buffer from being
accessed by multiple TX processes.
We can use cmpxchg() to try to modify tx.state to ISOTP_SENDING firstly.
If the modification of the previous process succeed, the later process
must wait tx.state to ISOTP_IDLE firstly. Thus, we can ensure TX buffer
is accessed by only one process at the same time. And we should also
restore the original tx.state at the subsequent error processes.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/c2517874fbdf4188585cf9ddf67a8fa74d5dbde5.1633764159.git.william.xuanziyang@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Using wait_event_interruptible() to wait for complete transmission,
but do not check the result of wait_event_interruptible() which can be
interrupted. It will result in TX buffer has multiple accessors and
the later process interferes with the previous process.
Following is one of the problems reported by syzbot.
=============================================================
WARNING: CPU: 0 PID: 0 at net/can/isotp.c:840 isotp_tx_timer_handler+0x2e0/0x4c0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.13.0-rc7+ #68
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
RIP: 0010:isotp_tx_timer_handler+0x2e0/0x4c0
Call Trace:
<IRQ>
? isotp_setsockopt+0x390/0x390
__hrtimer_run_queues+0xb8/0x610
hrtimer_run_softirq+0x91/0xd0
? rcu_read_lock_sched_held+0x4d/0x80
__do_softirq+0xe8/0x553
irq_exit_rcu+0xf8/0x100
sysvec_apic_timer_interrupt+0x9e/0xc0
</IRQ>
asm_sysvec_apic_timer_interrupt+0x12/0x20
Add result check for wait_event_interruptible() in isotp_sendmsg()
to avoid multiple accessers for tx buffer.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/10ca695732c9dd267c76a3c30f37aefe1ff7e32f.1633764159.git.william.xuanziyang@huawei.com
Cc: stable@vger.kernel.org
Reported-by: syzbot+78bab6958a614b0c80b9@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The receiver should abort TP if 'total message size' in TP.CM_RTS and
TP.CM_BAM is less than 9 or greater than 1785 [1], but currently the
j1939 stack only checks the upper bound and the receiver will accept
the following broadcast message:
vcan1 18ECFF00 [8] 20 08 00 02 FF 00 23 01
vcan1 18EBFF00 [8] 01 00 00 00 00 00 00 00
vcan1 18EBFF00 [8] 02 00 FF FF FF FF FF FF
This patch adds check for the lower bound and abort illegal TP.
[1] SAE-J1939-82 A.3.4 Row 2 and A.3.6 Row 6.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/all/1634203601-3460-1-git-send-email-zhangchangzhong@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the session state is J1939_SESSION_DONE, j1939_tp_rxtimer() will
give an alert "rx timeout, send abort", but do nothing actually. Move
the alert into session active judgment condition, it is more
reasonable.
One of the scenarios is that j1939_tp_rxtimer() execute followed by
j1939_xtp_rx_abort_one(). After j1939_xtp_rx_abort_one(), the session
state is J1939_SESSION_DONE, then j1939_tp_rxtimer() give an alert.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/all/20210906094219.95924-1-william.xuanziyang@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When I added IGMPv3 support I decided to follow the RFC for computing
the GMI dynamically:
" 8.4. Group Membership Interval
The Group Membership Interval is the amount of time that must pass
before a multicast router decides there are no more members of a
group or a particular source on a network.
This value MUST be ((the Robustness Variable) times (the Query
Interval)) plus (one Query Response Interval)."
But that actually is inconsistent with how the bridge used to compute it
for IGMPv2, where it was user-configurable that has a correct default value
but it is up to user-space to maintain it. This would make it consistent
with the other timer values which are also maintained correct by the user
instead of being dynamically computed. It also changes back to the previous
user-expected GMI behaviour for IGMPv3 queries which were supported before
IGMPv3 was added. Note that to properly compute it dynamically we would
need to add support for "Robustness Variable" which is currently missing.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: 0436862e41 ("net: bridge: mcast: support for IGMPv3/MLDv2 ALLOW_NEW_SOURCES report")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In `test_no_sockets` we don't expect any sockets, indeed
check_no_sockets() prints an error and exits if `sockets` list is
not empty, so free_sock_stat() call is unnecessary since it would
only be called when the `sockets` list is empty.
This was discovered by a strange warning printed by gcc v11.2.1:
In file included from ../../include/linux/list.h:7,
from vsock_diag_test.c:18:
vsock_diag_test.c: In function ‘test_no_sockets’:
../../include/linux/kernel.h:35:45: error: array subscript ‘struct vsock_stat[0]’ is partly outside array bound
s of ‘struct list_head[1]’ [-Werror=array-bounds]
35 | const typeof(((type *)0)->member) * __mptr = (ptr); \
| ^~~~~~
../../include/linux/list.h:352:9: note: in expansion of macro ‘container_of’
352 | container_of(ptr, type, member)
| ^~~~~~~~~~~~
../../include/linux/list.h:393:9: note: in expansion of macro ‘list_entry’
393 | list_entry((pos)->member.next, typeof(*(pos)), member)
| ^~~~~~~~~~
../../include/linux/list.h:522:21: note: in expansion of macro ‘list_next_entry’
522 | n = list_next_entry(pos, member); \
| ^~~~~~~~~~~~~~~
vsock_diag_test.c:325:9: note: in expansion of macro ‘list_for_each_entry_safe’
325 | list_for_each_entry_safe(st, next, sockets, list) {
| ^~~~~~~~~~~~~~~~~~~~~~~~
In file included from vsock_diag_test.c:18:
vsock_diag_test.c:333:19: note: while referencing ‘sockets’
333 | LIST_HEAD(sockets);
| ^~~~~~~
../../include/linux/list.h:23:26: note: in definition of macro ‘LIST_HEAD’
23 | struct list_head name = LIST_HEAD_INIT(name)
It seems related to some compiler optimization and assumption
about the empty `sockets` list, since this warning is printed
only with -02 or -O3. Also removing `exit(1)` from
check_no_sockets() makes the warning disappear since in that
case free_sock_stat() can be reached also when the list is
not empty.
Reported-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211014152045.173872-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-10-14
Brett ensures RDMA nodes are removed during release and rebuild. He also
corrects fw.mgmt.api to include the patch number for proper
identification.
Dave stops ida_free() being called when an IDA has not been allocated.
Michal corrects the order of parameters being provided and the number of
entries skipped for UDP tunnels.
====================
Link: https://lore.kernel.org/r/20211014181953.3538330-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit bdb7cc643f ("ipv6: Count interface receive statistics on the
ingress netdev") does not work when ip6_forward() executes on the skbs
with vrf-enslaved netdev. Use IP6CB(skb)->iif to get to the right one.
Add a selftest script to verify.
Fixes: bdb7cc643f ("ipv6: Count interface receive statistics on the ingress netdev")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211014130845.410602-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leonard Crestez says:
====================
tcp: md5: Fix overlap between vrf and non-vrf keys
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to
accept connection from the same client address in different VRFs. It is
also possible to set different MD5 keys for these clients which differ only
in the tcpm_l3index field.
This appears to work when distinguishing between different VRFs but not
between non-VRF and VRF connections. In particular:
* tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key. This
means that adding a key with l3index != 0 after a key with l3index == 0
will cause the earlier key to be deleted. Both keys can be present if the
non-vrf key is added later.
* _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This casues
failures if the passwords differ.
This can be fixed by making tcp_md5_do_lookup_exact perform an actual exact
comparison on l3index and by making __tcp_md5_do_lookup perfer vrf-bound
keys above other considerations like prefixlen.
The fact that keys with l3index==0 affect VRF connections is usually not
desirable, VRFs are meant to be completely independent. This behavior needs
to preserved for backwards compatibility. Also, applications can just bind
listen sockets to VRF and never specify TCP_MD5SIG_FLAG_IFINDEX at all.
So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0
was an error, accept this to mean "key only applies to default VRF". This
is what applications using VRFs for traffic separation want.
This also contains tests for the second part. It does not contain tests for
overlapping keys, that would require more changes in nettest to add
multiple keys. These scenarios are also covered by my tests for TCP-AO,
especially around this area:
https://github.com/cdleonard/tcp-authopt-test/blob/main/tcp_authopt_test/test_vrf_bind.py
Changes since V2:
* Rename --do-bind-key-ifindex to --force-bind-key-ifindex
* Fix referencing TCP_MD5SIG_FLAG_IFINDEX as TCP_MD5SIG_IFINDEX
Link to v2: https://lore.kernel.org/netdev/cover.1634107317.git.cdleonard@gmail.com/
Changes since V1:
* Accept (TCP_MD5SIG_IFINDEX with tcpm_ifindex == 0)
* Add flags for explicitly including or excluding TCP_MD5SIG_FLAG_IFINDEX
to nettest
* Add few more tests in fcnal-test.sh.
Link to v1: https://lore.kernel.org/netdev/3d8387d499f053dba5cd9184c0f7b8445c4470c6.1633542093.git.cdleonard@gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that applications binding listening sockets to VRFs without
specifying TCP_MD5SIG_FLAG_IFINDEX will work as expected. This would
be broken if __tcp_md5_do_lookup always made a strict comparison on
l3index. See this email:
https://lore.kernel.org/netdev/209548b5-27d2-2059-f2e9-2148f5a0291b@gmail.com/
Applications using tcp_l3mdev_accept=1 and a single global socket (not
bound to any interface) also should have a way to specify keys that are
only for the default VRF, this is done by --force-bind-key-ifindex
without otherwise binding to a device.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These options allow explicit control over the TCP_MD5SIG_FLAG_IFINDEX
flag instead of always setting it based on binding to an interface.
Do this by converting to getopt_long because nettest has too many
single-character flags already and getopt_long is widely used in
selftests.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple VRFs are generally meant to be "separate" but right now md5
keys for the default VRF also affect connections inside VRFs if the IP
addresses happen to overlap.
So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0
was an error, accept this to mean "key only applies to default VRF".
This is what applications using VRFs for traffic separation want.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to
accept connection from the same client address in different VRFs. It is
also possible to set different MD5 keys for these clients which differ
only in the tcpm_l3index field.
This appears to work when distinguishing between different VRFs but not
between non-VRF and VRF connections. In particular:
* tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key.
This means that adding a key with l3index != 0 after a key with l3index
== 0 will cause the earlier key to be deleted. Both keys can be present
if the non-vrf key is added later.
* _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This
casues failures if the passwords differ.
Fix this by making tcp_md5_do_lookup_exact perform an actual exact
comparison on l3index and by making __tcp_md5_do_lookup perfer
vrf-bound keys above other considerations like prefixlen.
Fixes: dea53bb80e ("tcp: Add l3index to tcp_md5sig_key and md5 functions")
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast':
lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le'
The actual use of crc32_le() comes indirectly through ether_crc().
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
transport encap_port update should be updated when sctp_vtag_verify()
succeeds, namely, returns 1, not returns 0. Correct it in this patch.
While at it, also fix the indentation.
Fixes: a1dd2cf2f1 ("sctp: allow changing transport encap_port by peer packets")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a86ed2cfa1 ("ptp: Don't print an error if ptp_kvm is not supported")
fixes the error message print on ARM platform by only concerning about
the case that the error returned from kvm_arch_ptp_init() is not -EOPNOTSUPP.
Although the ARM platform returns -EOPNOTSUPP if ptp_kvm is not supported
while X86_64 platform returns -KVM_EOPNOTSUPP, both error codes share the
same value 95.
Actually kvm_arch_ptp_init() on X86_64 platform can return three kinds of
errors (-KVM_ENOSYS, -KVM_EOPNOTSUPP and -KVM_EFAULT). The problem is that
-KVM_EOPNOTSUPP is masked out and -KVM_EFAULT is ignored among them.
This patch fixes this by returning them to ptp_kvm_init() respectively.
Signed-off-by: Kele Huang <huangkele@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - regressions:
- af_unix: rename UNIX-DGRAM to UNIX to maintain backwards compatibility
- procfs: revert "add seq_puts() statement for dev_mcast",
minor format change broke user space
Current release - new code bugs:
- dsa: fix bridge_num not getting cleared after ports leaving
the bridge, resource leak
- dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
bridges using VID 0, prevent packet drops if pvid is removed
- dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent
HW getting confused about station to VLAN mapping
Previous releases - regressions:
- virtio-net: fix for skb_over_panic inside big mode
- phy: do not shutdown PHYs in READY state
- dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's,
fix link LED staying lit after ifdown
- mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)
- mqprio: Correct stats in mqprio_dump_class_stats()
- ice: fix deadlock for Tx timestamp tracking flush
- stmmac: fix feature detection on old hardware
Previous releases - always broken:
- sctp: account stream padding length for reconf chunk
- icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()
- isdn: cpai: check ctr->cnr to avoid array index out of bound
- isdn: mISDN: fix sleeping function called from invalid context
- nfc: nci: fix potential UAF of rf_conn_info object
- dsa: microchip: prevent ksz_mib_read_work from kicking back
in after it's canceled in .remove and crashing
- dsa: mv88e6xxx: isolate the ATU databases of standalone and
bridged ports
- dsa: sja1105, ocelot: break circular dependency between switch
and tag drivers
- dsa: felix: improve timestamping in presence of packe loss
- mlxsw: thermal: fix out-of-bounds memory accesses
Misc:
- ipv6: ioam: move the check for undefined bits to improve
interoperability
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/K9E
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Quite calm.
The noisy DSA driver (embedded switches) changes, and adjustment to
IPv6 IOAM behavior add to diffstat's bottom line but are not scary.
Current release - regressions:
- af_unix: rename UNIX-DGRAM to UNIX to maintain backwards
compatibility
- procfs: revert "add seq_puts() statement for dev_mcast", minor
format change broke user space
Current release - new code bugs:
- dsa: fix bridge_num not getting cleared after ports leaving the
bridge, resource leak
- dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
bridges using VID 0, prevent packet drops if pvid is removed
- dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent HW
getting confused about station to VLAN mapping
Previous releases - regressions:
- virtio-net: fix for skb_over_panic inside big mode
- phy: do not shutdown PHYs in READY state
- dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's, fix link
LED staying lit after ifdown
- mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)
- mqprio: Correct stats in mqprio_dump_class_stats()
- ice: fix deadlock for Tx timestamp tracking flush
- stmmac: fix feature detection on old hardware
Previous releases - always broken:
- sctp: account stream padding length for reconf chunk
- icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()
- isdn: cpai: check ctr->cnr to avoid array index out of bound
- isdn: mISDN: fix sleeping function called from invalid context
- nfc: nci: fix potential UAF of rf_conn_info object
- dsa: microchip: prevent ksz_mib_read_work from kicking back in
after it's canceled in .remove and crashing
- dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged
ports
- dsa: sja1105, ocelot: break circular dependency between switch and
tag drivers
- dsa: felix: improve timestamping in presence of packe loss
- mlxsw: thermal: fix out-of-bounds memory accesses
Misc:
- ipv6: ioam: move the check for undefined bits to improve
interoperability"
* tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (60 commits)
icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe
MAINTAINERS: Update the devicetree documentation path of imx fec driver
sctp: account stream padding length for reconf chunk
mlxsw: thermal: Fix out-of-bounds memory accesses
ethernet: s2io: fix setting mac address during resume
NFC: digital: fix possible memory leak in digital_in_send_sdd_req()
NFC: digital: fix possible memory leak in digital_tg_listen_mdaa()
nfc: fix error handling of nfc_proto_register()
Revert "net: procfs: add seq_puts() statement for dev_mcast"
net: encx24j600: check error in devm_regmap_init_encx24j600
net: korina: select CRC32
net: arc: select CRC32
net: dsa: felix: break at first CPU port during init and teardown
net: dsa: tag_ocelot_8021q: fix inability to inject STP BPDUs into BLOCKING ports
net: dsa: felix: purge skb from TX timestamping queue if it cannot be sent
net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib
net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver
net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header
net: mscc: ocelot: deny TX timestamping of non-PTP packets
net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb
...
Currently when a user uses "devlink dev info", the fw.mgmt.api will be
the major.minor numbers as shown below:
devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial_number 00-01-00-ff-ff-00-00-00
versions:
fixed:
board.id K91258-000
running:
fw.mgmt 6.1.2
fw.mgmt.api 1.7 <--- No patch number included
fw.mgmt.build 0xd75e7d06
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.app.name ICE OS Default Package
fw.app 1.3.27.0
fw.app.bundle_id 0xc0000001
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
stored:
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
There are many features in the driver that depend on the major, minor,
and patch version of the FW. Without the patch number in the output for
fw.mgmt.api debugging issues related to the FW API version is difficult.
Also, using major.minor.patch aligns with the existing firmware version
which uses a 3 digit value.
Fix this by making the fw.mgmt.api print the major.minor.patch
versions. Shown below is the result:
devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial_number 00-01-00-ff-ff-00-00-00
versions:
fixed:
board.id K91258-000
running:
fw.mgmt 6.1.2
fw.mgmt.api 1.7.9 <--- patch number included
fw.mgmt.build 0xd75e7d06
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.app.name ICE OS Default Package
fw.app 1.3.27.0
fw.app.bundle_id 0xc0000001
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
stored:
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
Fixes: ff2e5c700e ("ice: add basic handler for devlink .info_get")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Correct parameters order in call to ice_tunnel_idx_to_entry function.
Entry in sparse port table is correct when the idx is 0. For idx 1 one
correct entry should be skipped, for idx 2 two of them should be skipped
etc. Change if condition to be true when idx is 0, which means that
previous valid entry of this tunnel type were skipped.
Fixes: b20e6c17c4 ("ice: convert to new udp_tunnel infrastructure")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the remove path, there is an attempt to free the aux_idx IDA whether
it was allocated or not. This can potentially cause a crash when
unloading the driver on systems that do not initialize support for RDMA.
But, this free cannot be gated by the status bit for RDMA, since it is
allocated if the driver detects support for RDMA at probe time, but the
driver can enter into a state where RDMA is not supported after the IDA
has been allocated at probe time and this would lead to a memory leak.
Initialize aux_idx to an invalid value and check for a valid value when
unloading to determine if an IDA free is necessary.
Fixes: d25a0fc41c ("ice: Initialize RDMA support")
Reported-by: Jun Miao <jun.miao@windriver.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently if the VSI is rebuilt/removed and the RDMA PF driver is active
the RDMA Tx queue scheduler node configuration will not be cleaned up.
This will cause the rebuild/re-add of the VSI to fail due to the
software structures not being correctly cleaned up for the VSI index.
Fix this by always calling ice_rm_vsi_rdma_cfg() for all VSI. If there
are no RDMA scheduler nodes created, then there is no harm in calling
ice_rm_vsi_rdma_cfg(). This change applies to all VSI types, so if
RDMA support is added for other VSI types they will also get this
change.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Jerzy Wiktor Jurkowski <jerzy.wiktor.jurkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In icmp_build_probe(), the icmp_ext_echo_iio parsing should be done
step by step and skb_header_pointer() return value should always be
checked, this patch fixes 3 places in there:
- On case ICMP_EXT_ECHO_CTYPE_NAME, it should only copy ident.name
from skb by skb_header_pointer(), its len is ident_len. Besides,
the return value of skb_header_pointer() should always be checked.
- On case ICMP_EXT_ECHO_CTYPE_INDEX, move ident_len check ahead of
skb_header_pointer(), and also do the return value check for
skb_header_pointer().
- On case ICMP_EXT_ECHO_CTYPE_ADDR, before accessing iio->ident.addr.
ctype3_hdr.addrlen, skb_header_pointer() should be called first,
then check its return value and ident_len.
On subcases ICMP_AFI_IP and ICMP_AFI_IP6, also do check for ident.
addr.ctype3_hdr.addrlen and skb_header_pointer()'s return value.
On subcase ICMP_AFI_IP, the len for skb_header_pointer() should be
"sizeof(iio->extobj_hdr) + sizeof(iio->ident.addr.ctype3_hdr) +
sizeof(struct in_addr)" or "ident_len".
v1->v2:
- To make it more clear, call skb_header_pointer() once only for
iio->indent's parsing as Jakub Suggested.
v2->v3:
- The extobj_hdr.length check against sizeof(_iio) should be done
before calling skb_header_pointer(), as Eric noticed.
Fixes: d329ea5bd8 ("icmp: add response to RFC 8335 PROBE messages")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/31628dd76657ea62f5cf78bb55da6b35240831f1.1634205050.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change the devicetree documentation path
to "Documentation/devicetree/bindings/net/fsl,fec.yaml"
since 'fsl-fec.txt' has been converted to 'fsl,fec.yaml' already.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211014110214.3254-1-caihuoqing@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sctp_make_strreset_req() makes repeated calls to sctp_addto_chunk()
which will automatically account for padding on each call. inreq and
outreq are already 4 bytes aligned, but the payload is not and doing
SCTP_PAD4(a + b) (which _sctp_make_chunk() did implicitly here) is
different from SCTP_PAD4(a) + SCTP_PAD4(b) and not enough. It led to
possible attempt to use more buffer than it was allocated and triggered
a BUG_ON.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Fixes: cc16f00f65 ("sctp: add support for generating stream reconf ssn reset request chunk")
Reported-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/b97c1f8b0c7ff79ac4ed206fc2c49d3612e0850c.1634156849.git.mleitner@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, mlxsw allows cooling states to be set above the maximum
cooling state supported by the driver:
# cat /sys/class/thermal/thermal_zone2/cdev0/type
mlxsw_fan
# cat /sys/class/thermal/thermal_zone2/cdev0/max_state
10
# echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state
# echo $?
0
This results in out-of-bounds memory accesses when thermal state
transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the
transition table is accessed with a too large index (state) [1].
According to the thermal maintainer, it is the responsibility of the
driver to reject such operations [2].
Therefore, return an error when the state to be set exceeds the maximum
cooling state supported by the driver.
To avoid dead code, as suggested by the thermal maintainer [3],
partially revert commit a421ce088a ("mlxsw: core: Extend cooling
device with cooling levels") that tried to interpret these invalid
cooling states (above the maximum) in a special way. The cooling levels
array is not removed in order to prevent the fans going below 20% PWM,
which would cause them to get stuck at 0% PWM.
[1]
BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290
Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122
Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016
Workqueue: events_freezable_power_ thermal_zone_device_check
Call Trace:
dump_stack_lvl+0x8b/0xb3
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
thermal_cooling_device_stats_update+0x271/0x290
__thermal_cdev_update+0x15e/0x4e0
thermal_cdev_update+0x9f/0xe0
step_wise_throttle+0x770/0xee0
thermal_zone_device_update+0x3f6/0xdf0
process_one_work+0xa42/0x1770
worker_thread+0x62f/0x13e0
kthread+0x3ee/0x4e0
ret_from_fork+0x1f/0x30
Allocated by task 1:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
thermal_cooling_device_setup_sysfs+0x153/0x2c0
__thermal_cooling_device_register.part.0+0x25b/0x9c0
thermal_cooling_device_register+0xb3/0x100
mlxsw_thermal_init+0x5c5/0x7e0
__mlxsw_core_bus_device_register+0xcb3/0x19c0
mlxsw_core_bus_device_register+0x56/0xb0
mlxsw_pci_probe+0x54f/0x710
local_pci_probe+0xc6/0x170
pci_device_probe+0x2b2/0x4d0
really_probe+0x293/0xd10
__driver_probe_device+0x2af/0x440
driver_probe_device+0x51/0x1e0
__driver_attach+0x21b/0x530
bus_for_each_dev+0x14c/0x1d0
bus_add_driver+0x3ac/0x650
driver_register+0x241/0x3d0
mlxsw_sp_module_init+0xa2/0x174
do_one_initcall+0xee/0x5f0
kernel_init_freeable+0x45a/0x4de
kernel_init+0x1f/0x210
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff8881052f7800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 1016 bytes inside of
1024-byte region [ffff8881052f7800, ffff8881052f7c00)
The buggy address belongs to the page:
page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0
head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[2] https://lore.kernel.org/linux-pm/9aca37cb-1629-5c67-1895-1fdc45c0244e@linaro.org/
[3] https://lore.kernel.org/linux-pm/af9857f2-578e-de3a-e62b-6baff7e69fd4@linaro.org/
CC: Daniel Lezcano <daniel.lezcano@linaro.org>
Fixes: a50c1e3565 ("mlxsw: core: Implement thermal zone")
Fixes: a421ce088a ("mlxsw: core: Extend cooling device with cooling levels")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After recent cleanups, gcc started warning about a suspicious
memcpy() call during the s2io_io_resume() function:
In function '__dev_addr_set',
inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:318:2,
inlined from 's2io_set_mac_addr' at drivers/net/ethernet/neterion/s2io.c:5205:2,
inlined from 's2io_io_resume' at drivers/net/ethernet/neterion/s2io.c:8569:7:
arch/x86/include/asm/string_32.h:182:25: error: '__builtin_memcpy' accessing 6 bytes at offsets 0 and 2 overlaps 4 bytes at offset 2 [-Werror=restrict]
182 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/netdevice.h:4648:9: note: in expansion of macro 'memcpy'
4648 | memcpy(dev->dev_addr, addr, len);
| ^~~~~~
What apparently happened is that an old cleanup changed the calling
conventions for s2io_set_mac_addr() from taking an ethernet address
as a character array to taking a struct sockaddr, but one of the
callers was not changed at the same time.
Change it to instead call the low-level do_s2io_prog_unicast() function
that still takes the old argument type.
Fixes: 2fd3768845 ("S2io: Added support set_mac_address driver entry point")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211013143613.2049096-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Richard Gong is no longer at Intel, so update the MAINTAINER's entry for
the Stratix10 firmware drivers.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This contains quite a few device-specific fixes for usual HD- and
USB-audio in addition to a couple of ALSA core fixes (a UAF fix in
sequencer and a fix for a misplaced PCM 32bit compat ioctl).
Nothing really stands out.
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmFoIj8OHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE9IrBAAvYoJvsUsZUwUSw0istIVaNiVBE4u91IBsNe/
W3WHVYAO4rLgZFfnasZ0kaPQ/BEwNhuk/vrJueZJuKU/kF8nCrYNX+nr8SB902Ws
xdoZhROtIIh9B8NO0D6yeYlIByJ1dldlqn/4+ujzPnY7ISWGbJ2KIcusnSsCte+e
2qMhT2paxjuSUFPZiPbXDGKPYcWYwn0lf7XjLe5lVlTAmHW2wX2PDs0wppkIXcXZ
C9Tkbz4SfCWh+HKrAd1AbYpP+OAF/9EetXGdBFDaZHex/AxNNi02588Fc84/Ofno
XxlO5/Z9O5VYVflsEGnF6B18D+Xsj94TC5h598OVDPgi5z2UgpQZusWTLGBfn4O4
LUbM+NYbLeaWLAwKi6wdAWq1b4eKx5m9Uxysb40bumR38rfauCTedolB+8OpsaRs
/kRjZmthgNXWDfjgAT6bPubwzpRdqscxA/SfY8lCObXVqgSdrmeFPCCqXYekKx4L
Xazx0tyMxbpIAoSo+rWzErLntpQ4Rijtq4t3mLcfl1U7m3tkq/D2zBHrrxENJSuC
TMko6F3maUSkGcGv+MMA2YO+J8juVEZ/vQFVT4C6PbOt1UnlpDQ8BHDxor+bVRpf
txK0o+5WOkPySRik1IkLRhScF0QIYbZnrdG/zSbSkcsDmxNbt3F1Jb5EGLheBpA4
yvzncTk=
=sxyi
-----END PGP SIGNATURE-----
Merge tag 'sound-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains quite a few device-specific fixes for usual HD- and
USB-audio in addition to a couple of ALSA core fixes (a UAF fix in
sequencer and a fix for a misplaced PCM 32bit compat ioctl).
Nothing really stands out"
* tag 'sound-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add quirk for VF0770
ALSA: hda: avoid write to STATESTS if controller is in reset
ALSA: hda/realtek: Fix the mic type detection issue for ASUS G551JW
ALSA: pcm: Workaround for a wrong offset in SYNC_PTR compat ioctl
ALSA: hda/realtek: Fix for quirk to enable speaker output on the Lenovo 13s Gen2
ALSA: hda: intel: Allow repeatedly probing on codec configuration errors
ALSA: hda/realtek: Add quirk for TongFang PHxTxX1
ALSA: hda/realtek - ALC236 headset MIC recording issue
ALSA: usb-audio: Enable rate validation for Scarlett devices
ALSA: hda/realtek: Add quirk for Clevo X170KM-G
ALSA: hda/realtek: Complete partial device name to avoid ambiguity
ALSA: hda - Enable headphone mic on Dell Latitude laptops with ALC3254
ALSA: seq: Fix a potential UAF by wrong private_free call order
ALSA: hda/realtek: Enable 4-speaker output for Dell Precision 5560 laptop
ALSA: usb-audio: Fix a missing error check in scarlett gen2 mixer
'skb' is allocated in digital_in_send_sdd_req(), but not free when
digital_in_send_cmd() failed, which will cause memory leak. Fix it
by freeing 'skb' if digital_in_send_cmd() return failed.
Fixes: 2c66daecc4 ("NFC Digital: Add NFC-A technology support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'params' is allocated in digital_tg_listen_mdaa(), but not free when
digital_send_cmd() failed, which will cause memory leak. Fix it by
freeing 'params' if digital_send_cmd() return failed.
Fixes: 1c7a4c24fb ("NFC Digital: Add target NFC-DEP support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When nfc proto id is using, nfc_proto_register() return -EBUSY error
code, but forgot to unregister proto. Fix it by adding proto_unregister()
in the error handling case.
Fixes: c7fe3b52c1 ("NFC: add NFC socket family")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211013034932.2833737-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/ethernet/korina.o: in function `korina_multicast_list':
korina.c:(.text+0x1af): undefined reference to `crc32_le'
Fixes: ef11291bcd ("Add support the Korina (IDT RC32434) Ethernet MAC")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Florian fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211012152509.21771-1-vegard.nossum@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/ethernet/arc/emac_main.o: in function `arc_emac_set_rx_mode':
emac_main.c:(.text+0xb11): undefined reference to `crc32_le'
The crc32_le() call comes through the ether_crc_le() call in
arc_emac_set_rx_mode().
[v2: moved the select to ARC_EMAC_CORE; the Makefile is a bit confusing,
but the error comes from emac_main.o, which is part of the arc_emac module,
which in turn is enabled by CONFIG_ARC_EMAC_CORE. Note that arc_emac is
different from emac_arc...]
Fixes: 775dd682e2 ("arc_emac: implement promiscuous mode and multicast filtering")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Link: https://lore.kernel.org/r/20211012093446.1575-1-vegard.nossum@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Felix DSA driver fixes
This is an assorted collection of fixes for issues seen on the NXP
LS1028A switch.
- PTP packet drops due to switch congestion result in catastrophic
damage to the driver's state
- loops are not blocked by STP if using the ocelot-8021q tagger
- driver uses the wrong CPU port when two of them are defined in DT
- module autoloading is broken* with both tagging protocol drivers
(ocelot and ocelot-8021q)
Changes in v2:
- Stop printing that we aren't going to take TX timestamps if we don't
have TX timestamping anyway, and we are just carrying PTP frames for a
cascaded DSA switch.
- Shorten the deferred xmit kthread name so that it fits the 16
character limit (TASK_COMM_LEN)
====================
Link: https://lore.kernel.org/r/20211012114044.2526146-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The NXP LS1028A switch has two Ethernet ports towards the CPU, but only
one of them is capable of acting as an NPI port at a time (inject and
extract packets using DSA tags).
However, using the alternative ocelot-8021q tagging protocol, it should
be possible to use both CPU ports symmetrically, but for that we need to
mark both ports in the device tree as DSA masters.
In the process of doing that, it can be seen that traffic to/from the
network stack gets broken, and this is because the Felix driver iterates
through all DSA CPU ports and configures them as NPI ports. But since
there can only be a single NPI port, we effectively end up in a
situation where DSA thinks the default CPU port is the first one, but
the hardware port configured to be an NPI is the last one.
I would like to treat this as a bug, because if the updated device trees
are going to start circulating, it would be really good for existing
kernels to support them, too.
Fixes: adb3dccf09 ("net: dsa: felix: convert to the new .change_tag_protocol DSA API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting up a bridge with stp_state 1, topology changes are not
detected and loops are not blocked. This is because the standard way of
transmitting a packet, based on VLAN IDs redirected by VCAP IS2 to the
right egress port, does not override the port STP state (in the case of
Ocelot switches, that's really the PGID_SRC masks).
To force a packet to be injected into a port that's BLOCKING, we must
send it as a control packet, which means in the case of this tagger to
send it using the manual register injection method. We already do this
for PTP frames, extend the logic to apply to any link-local MAC DA.
Fixes: 7c83a7c539 ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present, when a PTP packet which requires TX timestamping gets
dropped under congestion by the switch, things go downhill very fast.
The driver keeps a clone of that skb in a queue of packets awaiting TX
timestamp interrupts, but interrupts will never be raised for the
dropped packets.
Moreover, matching timestamped packets to timestamps is done by a 2-bit
timestamp ID, and this can wrap around and we can match on the wrong skb.
Since with the default NPI-based tagging protocol, we get no notification
about packet drops, the best we can do is eventually recover from the
drop of a PTP frame: its skb will be dead memory until another skb which
was assigned the same timestamp ID happens to find it.
However, with the ocelot-8021q tagger which injects packets using the
manual register interface, it appears that we can check for more
information, such as:
- whether the input queue has reached the high watermark or not
- whether the injection group's FIFO can accept additional data or not
so we know that a PTP frame is likely to get dropped before actually
sending it, and drop it ourselves (because DSA uses NETIF_F_LLTX, so it
can't return NETDEV_TX_BUSY to ask the qdisc to requeue the packet).
But when we do that, we can also remove the skb from the timestamping
queue, because there surely won't be any timestamp that matches it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocol drivers cannot depend on symbols exported by switch
drivers, because this creates a circular dependency that breaks module
autoloading.
The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function
exported by the common ocelot switch lib. This function looks at
OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the
DSA tag, for PTP timestamping (the command: one-step/two-step, and the
TX timestamp identifier).
None of that requires deep insight into the driver, it is quite
stateless, as it only depends upon the skb->cb. So let's make it a
static inline function and put it in include/linux/dsa/ocelot.h, a
file that despite its name is used by the ocelot switch driver for
populating the injection header too - since commit 40d3f295b5 ("net:
mscc: ocelot: use common tag parsing code with DSA").
With that function declared as static inline, its body is expanded
inside each call site, so the dependency is broken and the DSA tagger
can be built without the switch library, upon which the felix driver
depends.
Fixes: 39e5308b32 ("net: mscc: ocelot: support PTP Sync one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sad reality is that when a PTP frame with a TX timestamping request
is transmitted, it isn't guaranteed that it will make it all the way to
the wire (due to congestion inside the switch), and that a timestamp
will be taken by the hardware and placed in the timestamp FIFO where an
IRQ will be raised for it.
The implication is that if enough PTP frames are silently dropped by the
hardware such that the timestamp ID has rolled over, it is possible to
match a timestamp to an old skb.
Furthermore, nobody will match on the real skb corresponding to this
timestamp, since we stupidly matched on a previous one that was stale in
the queue, and stopped there.
So PTP timestamping will be broken and there will be no way to recover.
It looks like the hardware parses the sequenceID from the PTP header,
and also provides that metadata for each timestamp. The driver currently
ignores this, but it shouldn't.
As an extra resiliency measure, do the following:
- check whether the PTP sequenceID also matches between the skb and the
timestamp, treat the skb as stale otherwise and free it
- if we see a stale skb, don't stop there and try to match an skb one
more time, chances are there's one more skb in the queue with the same
timestamp ID, otherwise we wouldn't have ever found the stale one (it
is by timestamp ID that we matched it).
While this does not prevent PTP packet drops, it at least prevents
the catastrophic consequences of incorrect timestamp matching.
Since we already call ptp_classify_raw in the TX path, save the result
in the skb->cb of the clone, and just use that result in the interrupt
code path.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It appears that Ocelot switches cannot timestamp non-PTP frames,
I tested this using the isochron program at:
https://github.com/vladimiroltean/tsn-scripts
with the result that the driver increments the ocelot_port->ts_id
counter as expected, puts it in the REW_OP, but the hardware seems to
not timestamp these packets at all, since no IRQ is emitted.
Therefore check whether we are sending PTP frames, and refuse to
populate REW_OP otherwise.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aswath Govindraju
Yoshihiro Shimoda
Ziyang Xuan
Zhang Changzhong
Nikolay Aleksandrov
Stefano Garzarella
Jakub Kicinski
Stephen Suryaputra
David S. Miller
Leonard Crestez
Vegard Nossum
Xin Long
Kele Huang
Linus Torvalds
Brett Creeley
Michal Swiatkowski
Dave Ertman
Cai Huoqing
Eiichi Tsukata
Ido Schimmel
Arnd Bergmann
Dinh Nguyen
Vladimir Oltean
Nanyong Sun