CH Pro Throttle needs NOGET the same way as other products from
the same vendor require.
Reported-by: Unavowed <unavowed@vexillium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (48 commits)
HID: add support for Logitech Driving Force Pro wheel
HID: hid-ortek: remove spurious reference
HID: add support for Ortek PKB-1700
HID: roccat-koneplus: vorrect mode of sysfs attr 'sensor'
HID: hid-ntrig: init settle and mode check
HID: merge hid-egalax into hid-multitouch
HID: hid-multitouch: Send events per slot if CONTACTCOUNT is missing
HID: ntrig remove if and drop an indent
HID: ACRUX - activate the device immediately after binding
HID: ntrig: apply NO_INIT_REPORTS quirk
HID: hid-magicmouse: Correct touch orientation direction
HID: ntrig don't dereference unclaimed hidinput
HID: Do not create input devices for feature reports
HID: bt hidp: send Output reports using SET_REPORT on the Control channel
HID: hid-sony.c: Fix sending Output reports to the Sixaxis
HID: add support for Keytouch IEC 60945
HID: Add HID Report Descriptor to sysfs
HID: add IRTOUCH infrared USB to hid_have_special_driver
HID: kernel oops in out_cleanup in function hidinput_connect
HID: Add teletext/color keys - gyration remote - EU version (GYAR3101CKDE)
...
Per the HID Specification, Feature reports must be sent and received on
the Configuration endpoint (EP 0) through the Set_Report/Get_Report
interfaces. This patch adds two ioctls to hidraw to set and get feature
reports to and from the device. Modifications were made to hidraw and
usbhid.
New hidraw ioctls:
HIDIOCSFEATURE - Perform a Set_Report transfer of a Feature report.
HIDIOCGFEATURE - Perform a Get_Report transfer of a Feature report.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-multitouch: minor fixes based on additional review
HID: Switch turbox/mosart touchscreen to hid-mosart
HID: add Add Cando touch screen 10.1-inch product id
HID: hid-mulitouch: add support for the 'Sensing Win7-TwoFinger'
HID: hid-multitouch: add support for Cypress TrueTouch panels
HID: hid-multitouch: support for PixCir-based panels
HID: set HID_MAX_FIELD at 128
HID: add feature_mapping callback
This device used the MULTI_INPUT quirk whereas it could be used
with hid-mosart instead to support the multitouch part.
Reference: https://bugs.launchpad.net/ubuntu/+bug/620609/
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch doesn't alter functionality, but removes a dedicated kernel
thread.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Maulik Mankad <x0082077@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Neaten current uses of dev_<level> by adding and using
hid specific hid_<level> macros.
Convert existing uses of dev_<level> uses to hid_<level>.
Convert hid-pidff printk uses to hid_<level>.
Remove err_hid and use hid_err instead.
Add missing newlines to logging messages where necessary.
Coalesce format strings.
Add and use pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Other miscellaneous changes:
Add const struct hid_device * argument to hid-core functions
extract() and implement() so hid_<level> can be used by them.
Fix bad indentation in hid-core hid_input_field function
that calls extract() function above.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, if the device has been removed before hiddev_ioctl(),
the -EIO is returned. If it's removed while hiddev_ioctl() is in
progress, some commands are still processed fine, others
return -ENODEV. This change takes the "existancelock" before
processing ioctl commands and releases it at the end.
If the device has been removed, always returns -ENODEV.
Signed-off-by: Valentine Barshak <vbarshak@mvista.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A USB HID device can be disconnected at any time.
If this happens right before or while hiddev_ioctl is in progress,
the hiddev_ioctl tries to access invalid hiddev->hid pointer.
When the hid device is disconnected, the hiddev_disconnect()
ends up with a call to hid_device_release() which frees
hid_device, but doesn't set the hiddev->hid pointer to NULL.
If the deallocated memory region has been re-used by the kernel,
this can cause a crash or memory corruption.
Since disconnect can happen at any time, we can't initialize
struct hid_device *hid = hiddev->hid at the beginning of ioctl
and then use it.
This change checks hiddev->exist flag while holding
the existancelock and uses hid_device only if it exists.
Signed-off-by: Valentine Barshak <vbarshak@mvista.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the media keys of the Perixx PERIBOARD-707 (Plus)
keyboard / remote control.
Signed-off-by: Dennis Kügler <dennis.kuegler@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Changed Makefile to use <modules>-y instead of <modules>-objs because -objs is
deprecated and should now be switched. According to (documentation/kbuild/makefiles.txt).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Reference: https://bugs.launchpad.net/ubuntu/+bug/620609/
Signed-off-by: Pierre BAILLY <pierre@substantiel.fr>
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes three problems with the eGalax/DWAV multi-touch
screen found in the Eee PC T101MT:
1) While there is a dedicated multitouch driver for the screen
(hid-egalax.c), the MULTI_INPUT quirk is also applied, preventing
the hid-egalax driver from working. This patch removes the quirk
so the hid-egalax driver can handle the device correctly.
2) The x and y coordinates sent by the screen in multi-touch mode are
shifted by three bits from the events sent in single-touch mode, thus
the coordinates are out of range, leading to the pointer being stuck
in the bottom-right corner if no additional calibration is applied
(e.g. in the X evdev driver). This patch shifts the coordinates back.
This does not decrease accuracy as the last three bits of the "wrong"
coordinates are always 0.
3) Only multi-touch pressure events are sent, single touch emulation is
missing pressure information. This patch adds single-touch
ABS_PRESSURE events.
Signed-off-by: Philipp Merkel <mail@philmerk.de>
Acked-by: Stéphane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds the NOGET quirk for AXIS 295 Video Surveillance Joystick
(despite AXIS brand the vendor is actually CH Products). Without the quirk, the
joystick is detected but does not generate any events.
Signed-off-by: Rok Mandeljc <rok.mandeljc@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that hiddev_driver isn't being used for anything, there's no
reason to keep it around. This patch (as1419) gets rid of it
entirely.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Feature reports should only be sent on the control endpoint.
The USB HID standard is unclear and confusing on this issue. It seems to
suggest that Feature reports can be sent on a HID device's Interrupt OUT
endpoint. This cannot be the case because the report type is not encoded in
transfers sent out the Interrput OUT endpoint. If Feature reports were sent on
the Interrupt OUT endpint, they would be indistinguishable from Output reports
in the case where Report IDs were not used.
Further, Windows and Mac OS X do not send Feature reports out the interrupt OUT
Endpoint. They will only go out the Control Endpoint.
In addition, many devices simply do not hande Feature reports sent out the
Interrupt OUT endpoint.
Reported-by: simon@mungewell.org
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My macbook infrared remote control was broken by commit
bd25f4dd69 ("HID: hiddev: use
usb_find_interface, get rid of BKL").
This device appears in dmesg as:
apple 0003:05AC:8242.0001: hiddev0,hidraw0: USB HID v1.11 Device
[Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
It stopped working as lircd was getting ENODEV when opening /dev/usb/hiddev0.
AFAICS hiddev_driver is a dummy driver so usb_find_interface(&hiddev_driver)
does not find anything.
The device is associated with the usbhid driver, so let's do
usb_find_interface(&hid_driver) instead.
$ ls -l /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver
lrwxrwxrwx 1 root root 0 2010-09-12 16:28 /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver -> ../../../../../../bus/usb/drivers/usbhid
Signed-off-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add no-get quirk for eGalax touch controller to avoid timeout at probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Waltop Media Tablet 14.1 inch by fixing report descriptor.
This tablet is also sold as Genius G-Pen M712 (older version) and M712X
(newer version). Both are supported.
Trust Wide Screen Design Tablet (TB-7300, item no 15358) seems to be the
older version of this tablet (similar to Genius G-Pen M712), and could be
supported as well.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds a quirk for the eGalax touch controller which reports
two pairs of axes.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When I made commit 29129a98e6 ("HID: Send Report ID when numbered
reports are sent over the control endpoint"), I didn't account for *buf
not being the report ID anymore, as buf is incremented.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Kanvus Note A5 tablet (with USB ID 5543:6001, USB vendor UC_Logic) needs
the HID_QUIRK_MULTI_INPUT in order to work out of the box; otherwise, we get
the usual "cursor stuck at the upper left corner of the screen".
Signed-off-by: Decio Fonini <fonini@techk.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Waltop Slim Tablet 5.8 inch and Media Tablet 10.6 inch.
These (and other Waltop) tablets are usually sold by different companies
(such as Genius and Trust) and with different names, but with the same USB
vendor/product IDs.
Slim Tablet 5.8 inch is known to also be sold as Genius G-Pen F350 and Trust
Widescreen Mini Tablet (item no 16485).
Media Tablet 10.6 inch is known to also be sold as Genius G-Pen M609 and
M609X. Of these only the latter is known to be supported.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds a hid quirk for the chicony multitouch screen found in the Acer
Aspire 1820pt notebook.
Signed-off-by: David Gow <david@ingeniumdigital.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit bd25f4dd69 ("HID: hiddev: use usb_find_interface,
get rid of BKL") introduced using of private intfdata in hiddev for
purpose of storing hiddev pointer.
This is a problem, because intf pointer is already being set to struct
hid_device pointer by HID core. This obviously lead to memory corruptions
at device disconnect time, such as
WARNING: at lib/kobject.c:595 kobject_put+0x37/0x4b()
kobject: '(null)' (ffff88011e9cd898): is not initialized, yet kobject_put() is being called.
Convert hiddev into accessing hiddev through struct hid_device which is
in intfdata already.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-and-tested-by: Heinz Diehl <htd@fritha.org>
Reported-and-tested-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
One of our users reports consistently hitting a NULL dereference that
resolves to the "hid_to_usb_dev(hid);" call in hiddev_ioctl(), when
disconnecting a Lego WeDo USB HID device from an OLPC XO running
Scratch software. There's a FIXME comment and a guard against the
dereference, but that happens farther down the function than the
initial dereference does.
This patch moves the call to be below the guard, and the user reports
that it fixes the problem for him. OLPC bug report:
http://dev.laptop.org/ticket/10174
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for UC-Logic WP4030U, WP5540U and WP8060U tablets.
These tablets are usually sold by Genius, Trust and possibly others under
different names and in different cases, but with the original USB
vendor/product IDs.
Currently, these tablets are supported by standalone X.org driver WizardPen.
This patch aims to fix them in the kernel and make them supported by the
generic evdev X.org driver. Still, some minor fixes in the X.org driver are
to be made for the full stack support.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These devices report a usage page of type "consumer" and a usage of
"Programmable buttons". They are hence ignored by the hid-input layer.
Force the registration of an input device by using the new quirk type
HID_QUIRK_HIDINPUT_FORCE.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This removes the private hiddev_table in the usbhid
driver and changes it to use usb_find_interface
instead.
The advantage is that we can avoid the race between
usb_register_dev and usb_open and no longer need the
big kernel lock.
This doesn't introduce race condition -- the intf pointer could be
invalidated only in hiddev_disconnect() through usb_deregister_dev(),
but that will block on minor_rwsem and not actually remove the device
until usb_open().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "Greg Kroah-Hartman" <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Patch for linux-2.6.35-rc4 mainline kernel to enable Paul Qureshi's
Retro Adapter [http://keio.dk/retroadapter.html], an open source USB
device which allows controllers and joysticks from classic computers
and consoles to work on modern PCs, to appear as two separate devices
under Linux.
Signed-off-by: Peter Edwards <samwise@bagshot-row.org>
Acked-by: Paul Qureshi <retro@world3.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This USB flight yoke needs the NOGET quirk, like most of CH's other
products. This patch adds that.
Signed-off-by: Jonathan Rockway <jon@jrock.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers. There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical). Furthermore, only seven
drivers used it. We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.
The DMA-mapping portion of hcd.c is currently in flux. A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down. The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jiri Kosina
Linus Torvalds
Alan Ott
David Rientjes
Benjamin Tissoires
Oliver Neukum
Joe Perches
Valentine Barshak
Dennis Kügler
Tracey Dent
Arnd Bergmann
Pierre BAILLY
Philipp Merkel
Rok Mandeljc
Alan Stern
Guillaume Chazarain
Johan Hovold
Nikolai Kondrashov
Thierry Reding
Decio Fonini
David Gow
Chris Ball
Daniel Mack
Peter Edwards
Jonathan Rockway