Граф коммитов

24 Коммитов

Автор SHA1 Сообщение Дата
FUJITA Tomonori 824d7b570b [SCSI] scsi_lib: add scatter/gather data buffer accessors
This adds a set of accessors for the scsi data buffer. This is in
preparation for chaining sg lists and bidirectional requests (and
possibly, the mid-layer dma mapping).

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 16:29:59 -05:00
Mike Christie 181011e04a [SCSI] tgt: rm bio hacks in scsi tgt
scsi tgt breaks up a command into multple scatterlists
if we cannot fit all the data in one. This was because
the block rq helpers did not support large requests and
because we can get a command of any old size so it is
hard to preallocate pages for scatterlist large enough
(we cannot really preallocate pages with the bio map
user path). In 2.6.20, we added large request support to
the block layer helper, blk_rq_map_user. And at LSF,
we talked about increasing SCSI_MAX_PHYS_SEGMENTS for
scsi tgt if we want to support really really :) large
(greater than 256 * PAGE_SIZE in the worst mapping case)
requests.

The only target currently implemented does not even support
the multiple scatterlists stuff and only supports smaller
requests, so this patch just coverts scsi tgt to use
blk_rq_map_user.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:31:33 -05:00
FUJITA Tomonori b58d91547f [SCSI] export scsi-ml functions needed by tgt_scsi_lib and its LLDs
This patch contains the needed changes to the scsi-ml for the target
mode support.

Note, per the last review we moved almost all the fields we added
to the scsi_cmnd to our internal data structure which we are going
to try and kill off when we can replace it with support from other
parts of the kernel.

The one field we left on was the offset variable. This is needed to handle
the case where the target gets request that is so large that it cannot
execute it in one dma operation. So max_secotors or a segment limit may
limit the size of the transfer. In this case our tgt core code will
break up the command into managable transfers and send them to the
LLD one at a time. The offset is then used to tell the LLD where in
the command we are at. Is there another field on the scsi_cmd for
that?

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-11-25 13:08:56 -06:00
Christoph Hellwig 9e5c50fa86 [SCSI] remove SCSI_STATE_ #defines
These aren't used anymore since the field in scsi_cmnd where it was
stored has been removed.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-08-06 11:35:39 -05:00
Christoph Hellwig 631c228cd0 [SCSI] hide EH backup data outside the scsi_cmnd
Currently struct scsi_cmnd has various fields that are used to backup
original data after the corresponding fields have been overridden for
EH commands.  This means drivers can easily get at it and misuse it.
Due to the old_ naming this doesn't happen for most of them, but two
that have different names have been used wrong a lot (see previous
patch).  Another downside is that they unessecarily bloat the scsi_cmnd
size.

This patch moves them onstack in scsi_send_eh_cmnd to fix those two
issues aswell as allowing future EH fixes like moving the EH command
submissions to use SG lists like everything else.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-09 11:56:44 -05:00
Luben Tuikov 03aba2f795 [SCSI] sd/scsi_lib simplify sd_rw_intr and scsi_io_completion
This patch simplifies "good_bytes" computation in sd_rw_intr().
sd: "good_bytes" computation is always done in terms of the resolution
of the device's medium, since after that it is the number of good bytes
we pass around and other layers/contexts (as opposed ot sd) can translate
that to their own resolution (block layer:512).  It also makes
scsi_io_completion() processing more straightforward, eliminating the
3rd argument to the function.

It also fixes a couple of bugs like not checking return value,
using "break" instead of "return;", etc.

I've been running with this patch for some time now on a
test (do-it-all) system.

Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-26 10:00:20 -05:00
Jeff Garzik 71d530cd1b Merge branch 'master' into upstream
Conflicts:

	drivers/scsi/libata-core.c
	drivers/scsi/libata-scsi.c
	include/linux/pci_ids.h
2006-06-22 22:11:56 -04:00
Christoph Hellwig beb4048750 [SCSI] remove scsi_request infrastructure
With Achim patch the last user (gdth) is switched away from scsi_request
so we an kill it now.  Also disables some code in i2o_scsi that was
broken since the sg driver stopped using scsi_requests.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-10 16:24:40 -05:00
Luben Tuikov 89f48c4d67 [PATCH] SCSI: Introduce scsi_req_abort_cmd (REPOST)
Introduce scsi_req_abort_cmd(struct scsi_cmnd *).
This function requests that SCSI Core start recovery for the
command by deleting the timer and adding the command to the eh
queue.  It can be called by either LLDDs or SCSI Core.  LLDDs who
implement their own error recovery MAY ignore the timeout event if
they generated scsi_req_abort_cmd.

First post:
http://marc.theaimsgroup.com/?l=linux-scsi&m=113833937421677&w=2

Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>

Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15 20:57:18 +09:00
Guennadi Liakhovetski cdb8c2a6d8 [SCSI] dc395x: dynamically map scatter-gather for PIO
The current dc395x driver uses PIO to transfer up to 4 bytes which do not
get transferred by DMA (under unclear circumstances). For this the driver
uses page_address() which is broken on highmem. Apart from this the
actual calculation of the virtual address is wrong (even without highmem).
So, e.g., for reading it reads bytes from the driver to a wrong address
and returns wrong data, I guess, for writing it would just output random
data to the device.

The proper fix, as suggested by many, is to dynamically map data using
kmap_atomic(page, KM_BIO_SRC_IRQ) / kunmap_atomic(virt). The reason why it
has not been done until now, although I've done some preliminary patches
more than a year ago was that nobody interested in fixing this problem was
able to reliably reproduce it. Now it changed - with the help from
Sebastian Frei (CC'ed) I was able to trigger the PIO path. Thus, I was
also able to test and debug it.

There are 4 cases when PIO is used in dc395x - data-in / -out with and
without scatter-gather. I was able to reproduce and test only data-in with
and without SG. So, the data-out path is still untested, but it is also
somewhat simpler than the data-in. Fredrik Roubert (also CC'ed) also had
PIO triggering on his system, and in his case it was data-out without SG.
It would be great if he could test the attached patch on his system, but
even if he cannot, I would still request to apply the patch and just wait
if anybody cries...

Implementation: I put 2 new functions in scsi_lib.c and their declarations
in scsi_cmnd.h. I exported them without _GPL, although, I don't feel
strongly about that - not many drivers are likely to use them. But there
is at least one more - I want to use them in tmscsim.c. Whether these are
the right files for the functions and their declarations - not sure
either. Actually, they are not scsi-specific, so, might go somewhere
around other scattergather magic? They are not platform specific either,
and most SG functions are defined under arch/*/... As these issues were
discussed previously there were some more routines suggested to manipulate
scattergather buffers, I think, some of them were needed around
crypto code... So, might be a common place reasonable, like
lib/scattergather.c? I am open here.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-04-14 16:45:27 -05:00
Matthew Wilcox c67a848c35 [SCSI] Neaten comments in scsi_cmnd.h
Wrap these two comments at 80 columns

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-02-27 22:55:02 -06:00
Christoph Hellwig 776b23a036 [SCSI] always handle REQ_BLOCK_PC requests in common code
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just
fine in the core code.  There is a small behaviour change in that some
check in sr's rw_intr are bypassed, but I consider the old behaviour
a bug.

Mike found this cleanup opportunity and provdided early patches, so all
the credit goes to him, even if I redid the patches from scratch beause
that was easier than forward-porting the old patches.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:45 -06:00
James Bottomley 7b16318dea Fix up SCSI mismerge
I forgot to do a git-update-cache on the merged files ...
2005-12-15 20:17:02 -06:00
James Bottomley c9526497cf [SCSI] Consolidate REQ_BLOCK_PC handling path (fix ipod panic)
This follows on from Jens' patch and consolidates all of the ULD
separate handlers for REQ_BLOCK_PC into a single call which has his
fix for our direction bug.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-12-13 21:29:27 -08:00
Tim Schmielau 4e57b68178 [PATCH] fix missing includes
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.

In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch.  This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other.  So if any
hunk rejects or gets in the way of other patches, just drop it.  My scripts
will pick it up again in the next round.

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-10-30 17:37:32 -08:00
Al Viro c53033f6b0 [PATCH] gfp_t: drivers/scsi
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-10-28 08:16:50 -07:00
James Bottomley b21a413851 [SCSI] add global timeout to the scsi mid-layer
There are certain rogue devices (and the aic7xxx driver) that return
BUSY or QUEUE_FULL forever.  This code will apply a global timeout (of
the total number of retries times the per command timer) to a given
command.  If it is exceeded, the command is completed regardless of its
state.

The patch also removes the unused field in the command: timeout and
timeout_total.

This solves the problem of detecting an endless loop in the mid-layer
because of BUSY/QUEUE_FULL bouncing, but will not recover the device.
In the aic7xxx case, the driver can be recovered by sending a bus reset,
so possibly this should be tied into the error handler?

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-08-08 09:55:39 -05:00
Christoph Hellwig 8d115f845a [SCSI] remove scsi_cmnd->state
We never look at it except for the old megaraid driver that abuses it
for sending internal commands.  That usage can be fixed easily because
those internal commands are single-threaded by a mutex and we can easily
use a completion there.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-06-26 12:16:24 -05:00
Christoph Hellwig b4edcbcafd [SCSI] remove scsi_cmnd->owner
never checked anywhere

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-06-26 12:15:28 -05:00
Christoph Hellwig f5ad56145d [SCSI] remove scsi_cmnd->abort_reason
Never used for anything but printing it out in debug routines.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-06-26 12:14:46 -05:00
Christoph Hellwig a4c8f62851 [SCSI] remove scsi_cmnd.eh_state
it's never set to anything, and just three broken drivers are looking
at it and doing odd things.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-06-26 12:14:10 -05:00
c6295cdf65 [PATCH] scsi: remove meaningless scsi_cmnd->serial_number_at_timeout field
scsi_cmnd->serial_number_at_timeout doesn't serve any purpose
anymore.  All serial_number == serial_number_at_timeout tests
are always true in abort callbacks.  Kill the field.  Also, as
->pid always equals ->serial_number and ->serial_number
doesn't have any special meaning anymore, update comments
above ->serial_number accordingly.  Once we remove all uses of
this field from all lldd's, this field should go.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-04-18 12:33:15 -05:00
d3a933dc98 [PATCH] scsi: remove unused scsi_cmnd->internal_timeout field
scsi_cmnd->internal_timeout field doesn't have any meaning
anymore.  Kill the field.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-04-18 12:32:47 -05:00
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00