Check the aspeed timeout status register to see if the system has booted
from the secondary boot source. If so, set the watchdog device
bootstatus flag for "Card previously reset the CPU."
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Allow the device tree to specify a watchdog to fallover to
the alternate boot source.
The aspeeed watchdog can set a latch directing flash chip select 0 to
chip select 1, allowing boot from an alternate media if the watchdog
is not reset in time. On the ast2400 bank 1 also goes to flash bank 1,
while on the ast2500 the chip selects are swapped.
Also clear the secondary boot bit during the machine restart operation.
Otherwise, the system will switch to the alternate boot after every
reboot, which is not desired.
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Assert RESET_SYSTEM bit for any reset and set MODE field from reset
type.
The watchdog control register has a RESET_SYSTEM bit that is really
closer to activate a reset, and RESET_SYSTEM_MODE field that chooses
how much to reset.
Before this patch, a node without these optional property would do a
SOC reset, but a node with properties requesting a cpu or SOC reset
would do nothing and a node requesting a system reset would do a
SOC reset.
Fixes: b7f0b8ad25 ("drivers/watchdog: ASPEED reference dev tree properties for config")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Probing at device_initcall time lead to perverse cases where the
watchdog was probed after, say, I2C devices, which then leaves a
potentially running watchdog at the mercy of I2C device behaviour and
bus conditions.
Load the watchdog driver early to ensure that the kernel is patting it
well before initialising peripherals.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
An unintended post-condition of probe() is that the watchdog is
disabled. This behaviour was introduced by an unnecessary write to the
control register to configure the hardware based on the devicetree. The
write is unnecessary because the cached control value that is
manipulated by the code parsing the devicetree is eventually written by
aspeed_wdt_enable(), which is when we care how the control register
should be configured.
Remove the write to restore expected behaviour.
Fixes: b7f0b8ad25 ("drivers/watchdog: ASPEED reference dev tree properties for config")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for configuring the drive strength and polarity on the
AST2500, and the pulse duration on both the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Matt Spinler <mspinler@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reference the system device tree when configuring the watchdog
engines. If property 'aspeed,reset_type' is present then set
reset behavior based on the specified value. This can be one of
three different mutually exclusive values
* cpu - Reset CPU only on watchdog timeout
* soc - Reset System on Chip
* system - Full system reset
No reset can also be specified by indicating:
* none - No reset, assumes another watchdog is responsible for
this.
Add optional property 'aspeed,external-signal'. If present then
configure to generate external signal on watchdog timeout.
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Provides generic watchdog features as well as reboot support for the
Aspeed SoCs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Eddie James
Wim Van Sebroeck
Milton Miller
Andrew Jeffery
Christopher Bostic
Guenter Roeck
Joel Stanley