For applications running on a mix of platforms it's useful
to have a clear indication whether host's NIC supports the
geometry requirements of TCP zero-copy. TCP zero-copy Rx
requires data to be neatly placed into memory pages.
Most NICs can't do that.
This patch is adding GET support only, since the NICs
I work with either always have the feature enabled or
enable it whenever MTU is set to jumbo. In other words
I don't need SET. But adding set should be trivial.
(The only note on SET is that we will likely want
the setting to be "sticky" and use 0 / `unknown`
to reset it back to driver default.)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link extended sub-states are assigned as enum that is an integer
size but read from a union as u8, this is working for small values on
little endian systems but for big endian this always give 0. Fix the
variable in the union to match the enum size.
Fixes: ecc31c6024 ("ethtool: Add link extended state")
Signed-off-by: Moshe Tal <moshet@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to set rx buf len via ethtool -G parameter and get
rx buf len via ethtool -g parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an extended state and sub-state to describe link issues related to
transceiver modules.
The 'ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY' extended sub-state
tells user space that port is unable to gain a carrier because the CMIS
Module State Machine did not reach the ModuleReady (Fully Operational)
state. For example, if the module is stuck at ModuleLowPwr or
ModuleFault state. In case of the latter, user space can read the fault
reason from the module's EEPROM and potentially reset it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and
'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver
modules parameters and retrieve their status.
The first parameter to control is the power mode of the module. It is
only relevant for paged memory modules, as flat memory modules always
operate in low power mode.
When a paged memory module is in low power mode, its power consumption
is reduced to the minimum, the management interface towards the host is
available and the data path is deactivated.
User space can choose to put modules that are not currently in use in
low power mode and transition them to high power mode before putting the
associated ports administratively up. This is useful for user space that
favors reduced power consumption and lower temperatures over reduced
link up times. In QSFP-DD modules the transition from low power mode to
high power mode can take a few seconds and this transition is only
expected to get longer with future / more complex modules.
User space can control the power mode of the module via the power mode
policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible
values:
* high: Module is always in high power mode.
* auto: Module is transitioned by the host to high power mode when the
first port using it is put administratively up and to low power mode
when the last port using it is put administratively down.
The operational power mode of the module is available to user space via
the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not
reported to user space when a module is not plugged-in.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the CPU.
CMIS testing
============
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
The module is not in low power mode, as it is not forced by hardware
(LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off).
The power mode can be queried from the kernel. In case
LowPwrAllowRequestHW was on, the kernel would need to take into account
the state of the LowPwrRequestHW signal, which is not visible to user
space.
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp11 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp11 up
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp11 down
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
SFF-8636 testing
================
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm
Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm
Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm
Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm
Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm
Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm
Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm
The module is not in low power mode, as it is not forced by hardware
(Power override is on) or by software (Power set is off).
The power mode can be queried from the kernel. In case Power override
was off, the kernel would need to take into account the state of the
LPMode signal, which is not visible to user space.
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp13 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp13 up
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm
Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm
Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm
Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm
Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm
Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm
Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp13 down
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, there are many drivers who support CQE mode configuration,
some configure it as a fixed when initialized, some provide an
interface to change it by ethtool private flags. In order to make it
more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and
'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these
parameters can be accessed by ethtool netlink coalesce uAPI.
Also add an new structure kernel_ethtool_coalesce, then the
new parameter can be added into this struct.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ethtool compat ioctl handling is hidden away in net/socket.c,
which introduces a couple of minor oddities:
- The implementation may end up diverging, as seen in the RXNFC
extension in commit 84a1d9c482 ("net: ethtool: extend RXNFC
API to support RSS spreading of filter matches") that does not work
in compat mode.
- Most architectures do not need the compat handling at all
because u64 and compat_u64 have the same alignment.
- On x86, the conversion is done for both x32 and i386 user space,
but it's actually wrong to do it for x32 and cannot work there.
- On 32-bit Arm, it never worked for compat oabi user space, since
that needs to do the same conversion but does not.
- It would be nice to get rid of both compat_alloc_user_space()
and copy_in_user() throughout the kernel.
None of these actually seems to be a serious problem that real
users are likely to encounter, but fixing all of them actually
leads to code that is both shorter and more readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface for getting PHC (PTP Hardware Clock)
virtual clocks, which are based on PHC physical clock
providing hardware timestamp to network packets.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct is not visible to user space and therefore should not use the
user visible data types.
Instead, use internal data types like other structures in the file.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most devices maintain RMON (RFC 2819) stats - particularly
the "histogram" of packets received by size. Unlike other
RFCs which duplicate IEEE stats, the short/oversized frame
counters in RMON don't seem to match IEEE stats 1-to-1 either,
so expose those, too. Do not expose basic packet, CRC errors
etc - those are already otherwise covered.
Because standard defines packet ranges only up to 1518, and
everything above that should theoretically be "oversized"
- devices often create their own ranges.
Going beyond what the RFC defines - expose the "histogram"
in the Tx direction (assume for now that the ranges will
be the same).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of devices maintains the standard-based MAC control
counters for control frames. Add a API for those.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the MAC statistics are included in
struct rtnl_link_stats64, but some fields
are aggregated. Besides it's good to expose
these clearly hardware stats separately.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface for reading standard stats, including
stats which don't have a corresponding control interface.
Start with IEEE 802.3 PHY stats. There seems to be only
one stat to expose there.
Define API to not require user space changes when new
stats or groups are added. Groups are based on bitset,
stats have a string set associated.
v1: wrap stats in a nest
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to pause statistics add stats for FEC.
The IEEE standard mandates two sets of counters:
- 30.5.1.1.17 aFECCorrectedBlocks
- 30.5.1.1.18 aFECUncorrectableBlocks
where block is a block of bits FEC operates on.
Each of these counters is defined per lane (PCS instance).
Multiple vendors provide number of corrected _bits_ rather
than/as well as blocks.
This set adds the 2 standard-based block counters and a extra
one for corrected bits.
Counters are exposed to user space via netlink in new attributes.
Each attribute carries an array of u64s, first element is
the total count, and the following ones are a per-lane break down.
Much like with pause stats the operation will not fail when driver
does not implement the get_fec_stats callback (nor can the driver
fail the operation by returning an error). If stats can't be
reported the relevant attributes will be empty.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define get_module_eeprom_by_page() ethtool callback and implement
netlink infrastructure.
get_module_eeprom_by_page() allows network drivers to dump a part of
module's EEPROM specified by page and bank numbers along with offset and
length. It is effectively a netlink replacement for get_module_info()
and get_module_eeprom() pair, which is needed due to emergence of
complex non-linear EEPROM layouts.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some drivers clear the 'ethtool_link_ksettings' struct in their
get_link_ksettings() callback, before populating it with actual values.
Such drivers will set the new 'link_mode' field to zero, resulting in
user space receiving wrong link mode information given that zero is a
valid value for the field.
Another problem is that some drivers (notably tun) can report random
values in the 'link_mode' field. This can result in a general protection
fault when the field is used as an index to the 'link_mode_params' array
[1].
This happens because such drivers implement their set_link_ksettings()
callback by simply overwriting their private copy of
'ethtool_link_ksettings' struct with the one they get from the stack,
which is not always properly initialized.
Fix these problems by removing 'link_mode' from 'ethtool_link_ksettings'
and instead have drivers call ethtool_params_from_link_mode() with the
current link mode. The function will derive the link parameters (e.g.,
speed) from the link mode and fill them in the 'ethtool_link_ksettings'
struct.
v3:
* Remove link_mode parameter and derive the link parameters in
the driver instead of passing link_mode parameter to ethtool
and derive it there.
v2:
* Introduce 'cap_link_mode_supported' instead of adding a
validity field to 'ethtool_link_ksettings' struct.
[1]
general protection fault, probably for non-canonical address 0xdffffc00f14cc32c: 0000 [#1] PREEMPT SMP KASAN
KASAN: probably user-memory-access in range [0x000000078a661960-0x000000078a661967]
CPU: 0 PID: 8452 Comm: syz-executor360 Not tainted 5.11.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__ethtool_get_link_ksettings+0x1a3/0x3a0 net/ethtool/ioctl.c:446
Code: b7 3e fa 83 fd ff 0f 84 30 01 00 00 e8 16 b0 3e fa 48 8d 3c ed 60 d5 69 8a 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03
+38 d0 7c 08 84 d2 0f 85 b9
RSP: 0018:ffffc900019df7a0 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff888026136008 RCX: 0000000000000000
RDX: 00000000f14cc32c RSI: ffffffff873439ca RDI: 000000078a661960
RBP: 00000000ffff8880 R08: 00000000ffffffff R09: ffff88802613606f
R10: ffffffff873439bc R11: 0000000000000000 R12: 0000000000000000
R13: ffff88802613606c R14: ffff888011d0c210 R15: ffff888011d0c210
FS: 0000000000749300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004b60f0 CR3: 00000000185c2000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
linkinfo_prepare_data+0xfd/0x280 net/ethtool/linkinfo.c:37
ethnl_default_notify+0x1dc/0x630 net/ethtool/netlink.c:586
ethtool_notify+0xbd/0x1f0 net/ethtool/netlink.c:656
ethtool_set_link_ksettings+0x277/0x330 net/ethtool/ioctl.c:620
dev_ethtool+0x2b35/0x45d0 net/ethtool/ioctl.c:2842
dev_ioctl+0x463/0xb70 net/core/dev_ioctl.c:440
sock_do_ioctl+0x148/0x2d0 net/socket.c:1060
sock_ioctl+0x477/0x6a0 net/socket.c:1177
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: c8907043c6 ("ethtool: Get link mode in use instead of speed and duplex parameters")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix remaining issues with kdoc in the ethtool headers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extended link state structures and enums use kdoc headers
but then do not describe any of the members.
Convert to normal comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing kdoc for phy tunable callbacks.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to handle the common pattern of printing a string into the
ethtool strings interface and incrementing the string pointer by the
ETH_GSTRING_LEN. Most of the drivers end up doing this and several have
implemented their own versions of this function so it would make sense to
consolidate on one implementation.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, get the link mode bit in use, and derive each of the parameters
from it in ethtool.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes. For
example, 2x50 or 4x25.
Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.
When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.
Example:
$ ethtool -s swp1 lanes 4
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseSR/Full
50000baseCR2/Full
100000baseSR4/Full
100000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: no
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bitmask represents all existing coalesce parameters.
Signed-off-by: Antonio Cardace <acardace@redhat.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define get/set phy tunable callbacks in ethtool ops.
This will allow MAC drivers with integrated PHY still to implement
these tunables.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drivers have to report their pause frames statistics
via ethtool -S, and there is a wide variety of names used for
these statistics.
Add the two statistics defined in IEEE 802.3x to the standard
API. Create a new ethtool request header flag for including
statistics in the response to GET commands.
Always create the ETHTOOL_A_PAUSE_STATS nest in replies when
flag is set. Testing if driver declares the op is not a reliable
way of checking if any stats will actually be included and therefore
we don't want to give the impression that presence of
ETHTOOL_A_PAUSE_STATS indicates driver support.
Note that this patch does not include PFC counters, which may fit
better in dcbnl? But mostly I don't need them/have a setup to test
them so I haven't looked deeply into exposing them :)
v3:
- add a helper for "uninitializing" stats, rather than a cryptic
memset() (Andrew)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend ethtool_phy_ops to include the 3 function pointers necessary for
implementing PHY statistics. In a subsequent change we will uninline
those functions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to decouple ethtool from its PHY library dependency, define an
ethtool_phy_ops singleton which can be overriden by the PHY library when
it loads with an appropriate set of function pointers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, drivers can only tell whether the link is up/down using
LINKSTATE_GET, but no additional information is given.
Add attributes to LINKSTATE_GET command in order to allow drivers
to expose the user more information in addition to link state to ease
the debug process, for example, reason for link down state.
Extended state consists of two attributes - link_ext_state and
link_ext_substate. The idea is to avoid 'vendor specific' states in order
to prevent drivers to use specific link_ext_state that can be in the future
common link_ext_state.
The substates allows drivers to add more information to the common
link_ext_state. For example, vendor can expose 'Autoneg' as link_ext_state
and add 'No partner detected during force mode' as link_ext_substate.
If a driver cannot pinpoint the extended state with the substate
accuracy, it is free to expose only the extended state and omit the
substate attribute.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Now that all in-tree drivers have been updated we can
make the supported_coalesce_params mandatory.
To save debugging time in case some driver was missed
(or is out of tree) add a warning when netdev is registered
with set_coalesce but without supported_coalesce_params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux supports 22 different interrupt coalescing parameters.
No driver implements them all. Some drivers just ignore the
ones they don't support, while others have to carry a long
list of checks to reject unsupported settings.
To simplify the drivers add the ability to specify inside
ethtool_ops which parameters are supported and let the core
reject attempts to set any other one.
This commit makes the mechanism an opt-in, only drivers which
set ethtool_opts->coalesce_types to a non-zero value will have
the checks enforced.
The same mask is used for global and per queue settings.
v3: - move the (temporary) check if driver defines types
earlier (Michal)
- rename used_types -> nonzero_params, and
coalesce_types -> supported_coalesce_params (Alex)
- use EOPNOTSUPP instead of EINVAL (Andrew, Michal)
Leaving the long series of ifs for now, it seems nice to
be able to grep for the field and flag names. This will
probably have to be revisited once netlink support lands.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three virtual devices (ibmveth, virtio_net, and netvsc) all have
similar code to set link settings and validate ethtool command. To
eliminate duplication of code, it is factored out into core/ethtool.c.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool ops get_rxfh_context and set_rxfh_context are used to create,
remove and access parameters associated to RSS contexts, in a similar
fashion to get_rxfh and set_rxfh.
Add a small descritopn of these callbacks in the struct ethtool_ops doc.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way to define __ETHTOOL_LINK_MODE_MASK_NBITS seems to be overly
complicated, go with a standard approach instead.
Whilst we're at it, move the comment to the right place.
v2:
- rebased
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to translate the ethtool_rx_flow_spec
structure to the flow_rule representation.
This allows us to reuse code from the driver side given that both flower
and ethtool_rx_flow interfaces use the same representation.
This patch also includes support for the flow type flags FLOW_EXT,
FLOW_MAC_EXT and FLOW_RSS.
The ethtool_rx_flow_spec_input wrapper structure is used to convey the
rss_context field, that is away from the ethtool_rx_flow_spec structure,
and the ethtool_rx_flow_spec structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since [gs]et_settings ethtool_ops callbacks have been deprecated in
February 2016, all in tree NIC drivers have been converted to provide
[gs]et_link_ksettings() and out of tree drivers have had enough time to do
the same.
Drop get_settings() and set_settings() and implement both ETHTOOL_[GS]SET
and ETHTOOL_[GS]LINKSETTINGS only using [gs]et_link_ksettings().
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new callback: get_ethtool_phy_stats() which allows network device
drivers not making use of the PHY library to return PHY statistics.
Update ethtool_get_phy_stats(), __ethtool_get_sset_count() and
__ethtool_get_strings() accordingly to interogate the network device
about ETH_SS_PHY_STATS.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding support for ethtool::get_fecparam and set_fecparam, kernel
doc for these functions was missed, add those.
Fixes: 1a5f3da20b ("net: ethtool: add support for forward error correction modes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use a two-step process to configure a filter with RSS spreading. First,
the RSS context is allocated and configured using ETHTOOL_SRSSH; this
returns an identifier (rss_context) which can then be passed to subsequent
invocations of ETHTOOL_SRXCLSRLINS to specify that the offset from the RSS
indirection table lookup should be added to the queue number (ring_cookie)
when delivering the packet. Drivers for devices which can only use the
indirection table entry directly (not add it to a base queue number)
should reject rule insertions combining RSS with a nonzero ring_cookie.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function provides a way to intersect two link masks together to
find the common ground between them. For example in i40e, the driver
first generates link masks for what is supported by the PHY type. The
driver then gets the link masks for what the NVM supports. The
resulting intersection between them yields what can truly be supported.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Subbaraya Sundeep
Jakub Kicinski
Moshe Tal
Hao Chen
Ido Schimmel
Yufeng Mo
Arnd Bergmann
Yangbo Lu
Vladyslav Tarasiuk
Danielle Ratson
Alexander Duyck
Antonio Cardace
Igor Russkikh
Florian Fainelli
Amit Cohen
Gustavo A. R. Silva
Cris Forno
Maxime Chevallier
Heiner Kallweit
Pablo Neira Ayuso
Michal Kubecek
Edward Cree
David S. Miller
Greg Kroah-Hartman
Alan Brady