A driver which emits both decimal and hex numbers in its printk
creates confusion as to what is what. Prefix hex numbers with 0x.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Include the revision number of the PL08x primecell in the boot-time
printk to allow proper identification of the peripheral. Reformat
the announcement printk format reflect what we do for other primecell
drivers - generally "PLXXX revX at 0xNNNNNNNN irq X".
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Explain the two flow control methods which the PL08x implements, along
with the problem which peripheral flow control presents. This helps
people understand why we are unable to use these DMA controllers with
(eg) the MMCI.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
drivers/dma/amba-pl08x.c:1895:40: warning: Unknown escape '%'
drivers/dma/amba-pl08x.c:1903:40: warning: Unknown escape '%'
drivers/dma/amba-pl08x.c:513:6: warning: symbol 'pl08x_choose_master_bus' was not declared. Should it be static?
drivers/dma/amba-pl08x.c:604:5: warning: symbol 'pl08x_fill_llis_for_desc' was not declared. Should it be static?
drivers/dma/amba-pl08x.c:1442:32: warning: symbol 'pl08x_prep_slave_sg' was not declared. Should it be static?
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Trying to disable a tasklet while holding a spinlock which the tasklet
will take is a recipe for deadlock - tasklet_disable() will wait for the
tasklet to finish running, which it will never do. In any case, there
is not a corresponding tasklet_enable(), so once the tasklet is disabled,
it will never run again until reboot.
It's safe to just remove the tasklet_disable() as we remove all current
and pending descriptors before releasing this spinlock. This means that
the tasklet will find no remaining work if it subsequently runs.
The only remaining issue is that the callback for an already submitted
txd may be in progress, or even called after terminate_all() returns.
There's not much that can be done about that as waiting for the callback
to complete before returning will also lead to deadlocks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
pl08x_issue_pending() returns with the spinlock locked and interrupts
disabled if the channel is waiting for a physical DMA to become free.
This is wrong - especially as pl08x_issue_pending() is an API function
as it leads to deadlocks. Fix it to always return with the spinlock
unlocked.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If we fail to allocate the LLI, the prep_* function will return NULL.
However, the TXD we allocated will not be placed on any list, nor
will it be freed - we'll just drop all references to it. Make sure
we free it rather than leaking TXDs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tasklets are run from an interruptible context. The slave DMA functions
can be called from within IRQ handlers. Taking the spinlock without
disabling interrupts allows an interrupt handler to run, which may try
to take the spinlock again, resulting in deadlock. Fix this by using
the irqsave spinlocks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The last_issued variable uses an atomic type, which is only
incremented inside a protected region, and then read. Everywhere else
only reads the value, so it isn't using atomic_t correctly, and it
doesn't even need to. Moreover, the DMA engine code provides us with
a variable for this already - chan.cookie. Use chan.cookie instead.
Also, avoid negative dma_cookie_t values - negative returns from
tx_submit() mean failure, yet in reality we always succeed. Restart
from cookie 1, just like other DMA engine drivers do.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If maxburst was passed in as zero, we would overflow the burst_sizes[]
array. Fix this by checking for this condition, and defaulting to
single transfer 'bursts'.
Improve the readability of the loop using a for() loop rather than
a while() loop with the iterator initialized far from the loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Correct mis-spellings in comments and printk strings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
PowerPC relies on IRQ-disable to guard against RCU quiecent states,
use the appropriate RCU call version.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This reverts commit e0fdace10e.
On-list discussion seems to suggest that the robustness fixes for printk
make this unnecessary and DaveM has also agreed in person at Kernel Summit
and on list.
The main problem with this code is once we hit a lockdep splat we always
keep oops_in_progress set, the console layer uses oops_in_progress with KMS
to decide when it should be showing the oops and not showing X, so it causes
problems around suspend/resume time when a userspace resume can cause a console
switch away from X, only if oops_in_progress is set (which is what we want
if an oops actually is in progress, but not because we had a lockdep splat
2 days prior).
Cc: David S Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2+: PM/serial: hold console semaphore while OMAP UARTs are disabled
OMAP: UART: don't resume UARTs that are not enabled.
Some Lenovos have TPMs that require a quirk to function correctly. This can
be autodetected by checking whether the device has a _HID of INTC0102. This
is an invalid PNPid, and as such is discarded by the pnp layer - however
it's still present in the ACPI code, so we can pull it out that way. This
means that the quirk won't be automatically applied on non-ACPI systems,
but without ACPI we don't have any way to identify the chip anyway so I
don't think that's a great concern.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: James Morris <jmorris@namei.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (24 commits)
Btrfs: don't use migrate page without CONFIG_MIGRATION
Btrfs: deal with DIO bios that span more than one ordered extent
Btrfs: setup blank root and fs_info for mount time
Btrfs: fix fiemap
Btrfs - fix race between btrfs_get_sb() and umount
Btrfs: update inode ctime when using links
Btrfs: make sure new inode size is ok in fallocate
Btrfs: fix typo in fallocate to make it honor actual size
Btrfs: avoid NULL pointer deref in try_release_extent_buffer
Btrfs: make btrfs_add_nondir take parent inode as an argument
Btrfs: hold i_mutex when calling btrfs_log_dentry_safe
Btrfs: use dget_parent where we can UPDATED
Btrfs: fix more ESTALE problems with NFS
Btrfs: handle NFS lookups properly
btrfs: make 1-bit signed fileds unsigned
btrfs: Show device attr correctly for symlinks
btrfs: Set file size correctly in file clone
btrfs: Check if dest_offset is block-size aligned before cloning file
Btrfs: handle the space_cache option properly
btrfs: Fix early enospc because 'unused' calculated with wrong sign.
...
Its easy to eat all kernel memory and trigger NMI watchdog, using an
exploit program that queues unix sockets on top of others.
lkml ref : http://lkml.org/lkml/2010/11/25/8
This mechanism is used in applications, one choice we have is to have a
recursion limit.
Other limits might be needed as well (if we queue other types of files),
since the passfd mechanism is currently limited by socket receive queue
sizes only.
Add a recursion_level to unix socket, allowing up to 4 levels.
Each time we send an unix socket through sendfd mechanism, we copy its
recursion level (plus one) to receiver. This recursion level is cleared
when socket receive queue is emptied.
Reported-by: Марк Коренберг <socketpair@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong of initializer entry was modified.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's AUTHOR was changed to "Toshiharu Okada" from "Masayuki Ohtake".
I update the Kconfig, renamed "Topcliff" to "EG20T".
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 58933c64(ucc_geth: Fix the wrong the Rx/Tx FIFO size),
the UCC_GETH_UTFTT_INIT is set to 512 based on the recommendation
of the QE Reference Manual. But that will sometimes cause tx halt
while working in half duplex mode.
According to errata draft QE_GENERAL-A003(High Tx Virtual FIFO
threshold size can cause UCC to halt), setting UTFTT less than
[(UTFS x (M - 8)/M) - 128] will prevent this from happening
(M is the minimum buffer size).
The patch changes UTFTT back to 256.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Jean-Denis Boyer <jdboyer@media5corp.com>
Cc: Andreas Schmitz <Andreas.Schmitz@riedel.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet sockets corresponding to passive connections are added to the bind hash
using ___inet_inherit_port(). These sockets are later removed from the bind
hash using __inet_put_port(). These two functions are not exactly symmetrical.
__inet_put_port() decrements hashinfo->bsockets and tb->num_owners, whereas
___inet_inherit_port() does not increment them. This results in both of these
going to -ve values.
This patch fixes this by calling inet_bind_hash() from ___inet_inherit_port(),
which does the right thing.
'bsockets' and 'num_owners' were introduced by commit a9d8f9110d
(inet: Allowing more than 64k connections and heavily optimize bind(0))
Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some debug information about ehea not being able to
allocate enough spaces. Also it correctly updates the amount of available
skb.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new DIO bio splitting code has problems when the bio
spans more than one ordered extent. This will happen as the
generic DIO code merges our get_blocks calls together into
a bigger single bio.
This fixes things by walking forward in the ordered extent
code finding all the overlapping ordered extents and completing them
all at once.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This avoids some include-file hell, and the function isn't really
important enough to be inlined anyway.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And in particular, use it in 'pipe_fcntl()'.
The other pipe functions do not need to use the 'careful' version, since
they are only ever called for things that are already known to be pipes.
The normal read/write/ioctl functions are called through the file
operations structures, so if a file isn't a pipe, they'd never get
called. But pipe_fcntl() is special, and called directly from the
generic fcntl code, and needs to use the same careful function that the
splice code is using.
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.. and change it to take the 'file' pointer instead of an inode, since
that's what all users want anyway.
The renaming is preparatory to exporting it to other users. The old
'pipe_info()' name was too generic and is already used elsewhere, so
before making the function public we need to use a more specific name.
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The HSO driver incorrectly creates a serial device instead of a net
device when disable_net is set. It shouldn't create anything for the
network interface.
Signed-off-by: Filip Aben <f.aben@option.com>
Reported-by: Piotr Isajew <pki@ex.com.pl>
Reported-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We register lapb when tty is created, but unregister it only when the
device is UP. So move the lapb_unregister to x25_asy_close_tty after
the device is down.
The old behaviour causes ldisc switching to fail each second attempt,
because we noted for us that the device is unused, so we use it the
second time, but labp layer still have it registered, so it fails
obviously.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Sergey Lapin <slapin@ossfans.org>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Mikhail Ulyanov <ulyanov.mikhail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were truncating the number of unicast and multicast MAC addresses
supported. Additionally, we were incorrectly computing the MAC Address
hash (a "1 << N" where we needed a "1ULL << N").
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating unit from ird might return several error codes
not only -EAGAIN, so it should not be changed and returned
precisely. Same time unit release procedure should be invoked
only if device is unregistering.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single uninitialized padding byte is leaked to userspace.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
"aup->enable" holds already the address pointing to the MAC enable
register. The bug was introduced by commit d0e7cb:
"au1000-eth: remove volatiles, switch to I/O accessors".
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug in updating the Greatest Acknowledgment number Received (GAR):
the current implementation does not track the greatest received value -
lower values in the range AWL..AWH (RFC 4340, 7.5.1) erase higher ones.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_win_from_space() does the following:
if (sysctl_tcp_adv_win_scale <= 0)
return space >> (-sysctl_tcp_adv_win_scale);
else
return space - (space >> sysctl_tcp_adv_win_scale);
"space" is int.
As per C99 6.5.7 (3) shifting int for 32 or more bits is
undefined behaviour.
Indeed, if sysctl_tcp_adv_win_scale is exactly 32,
space >> 32 equals space and function returns 0.
Which means we busyloop in tcp_fixup_rcvbuf().
Restrict net.ipv4.tcp_adv_win_scale to [-31, 31].
Fix https://bugzilla.kernel.org/show_bug.cgi?id=20312
Steps to reproduce:
echo 32 >/proc/sys/net/ipv4/tcp_adv_win_scale
wget www.kernel.org
[softlockup]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The /proc/net/tcp leaks openreq sockets from other namespaces.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the if and else conditional because the code is in mainline and there
is no need in it being there.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a problem with how we use sget, it searches through the list of supers
attached to the fs_type looking for a super with the same fs_devices as what
we're trying to mount. This depends on sb->s_fs_info being filled, but we don't
fill that in until we get to btrfs_fill_super, so we could hit supers on the
fs_type super list that have a null s_fs_info. In order to fix that we need to
go ahead and setup a blank root with a blank fs_info to hold fs_devices, that
way our test will work out right and then we can set s_fs_info in
btrfs_set_super, and then open_ctree will simply use our pre-allocated root and
fs_info when setting everything up. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There are two big problems currently with FIEMAP
1) We return extents for holes. This isn't supposed to happen, we just don't
return extents for holes and then userspace interprets the lack of an extent as
a hole.
2) We sometimes don't set FIEMAP_EXTENT_LAST properly. This is because we wait
to see a EXTENT_FLAG_VACANCY flag on the em, but this won't happen if say we ask
fiemap to map up to the last extent in a file, and there is nothing but holes up
to the i_size. To fix this we need to lookup the last extent in this file and
save the logical offset, so if we happen to try and map that extent we can be
sure to set FIEMAP_EXTENT_LAST.
With this patch we now pass xfstest 225, which we never have before.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When mounting a btrfs file system btrfs_test_super() may attempt to
use sb->s_fs_info, the btrfs root, of a super block that is going away
and that has had the btrfs root set to NULL in its ->put_super(). But
if the super block is going away it cannot be an existing super block
so we can return false in this case.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>