Added a new function which waits for the ringbuffer space to be equal to
(total - 8). This is the empty condition of the ringbuffer, and
equivalent to head==tail.
Also modified two users of this functionality elsewhere in the code.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
i915 calls the panic handler function on last close to reset the modes,
however this is a really bad idea for multi-gpu machines, esp shareable
gpus machines. So add a new entry point for the driver to just restore
its own fbcon mode.
v2: move code into fb helper, fix panic code to block mode change on
powered off GPUs.
[airlied: this hits drm core and I wrote it and it was reviewed on intel-gfx
so really I signed it off twice ;-).]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On a Thinkpad x61s, I noticed some memory corruption when
plugging/unplugging the external VGA connection. The symptoms are that
4 bytes at the beginning of a page get overwritten by zeroes.
The address of the corruption varies when rebooting the machine, but
stays constant while it's running (so it's possible to repeatedly write
some data and then corrupt it again by plugging the cable).
Further investigation revealed that the corrupted address is
(dev_priv->status_page_dmah->busaddr & 0xffffffff), ie. the beginning of
the hardware status page of the i965 graphics card, cut to 32 bits.
So it seems that for some memory access, the hardware uses only 32 bit
addressing. If the hardware status page is located >4GB, this
corrupts unrelated memory.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Userspace has a legitimate requirement to use a delta that points to
outside of the target bo, and so we need to enable this. (As this is an
abi break, albeit a relaxation of the current restrictions, mark the change
with a new flag.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We had some conversions over to the _PIPE macros, but didn't get
everything. So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.
[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A lot of minor tweaks to fix the tracepoints, improve the outputting for
ftrace, and to generally make the tracepoints useful again. It is a start
and enough to begin identifying performance issues and gaps in our
coverage.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Starting with SandyBridge (though possible with earlier hacked BIOSes),
the BIOS may initialise the IGFX as secondary to a discrete GPU. Prior,
it would simply disable the integrated GPU. So we adjust our PCI class
mask to match any DISPLAY_CLASS device.
In such a configuration, the IGFX is not a primary VGA controller and
so should not take part in VGA arbitration, and the error return from
vga_client_register() is expected.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Move code around and invoke iomem annotation in a few more places in
order to silence sparse. Still a few more iomem annotations to go...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As has_gem is unconditionally set to true, the conditional immediately
following that assignment is superfluous.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The IPS driver is designed to be able to run detached from i915 and
just not enable GPU turbo in that case, in order to avoid module
dependencies between the two drivers. This means that we don't know
what the load order between the two is going to be, and we had
previously only supported IPS after (optionally) i915, but not i915
after IPS. If the wrong order was chosen, you'd get no GPU turbo, and
something like half the possible graphics performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The relative-to-general state default is useless as it means having to
rewrite the streaming kernels for each batch. Relative-to-surface is
more useful, as that stream usually needs to be rewritten for each
batch. And absolute addressing mode, vital if you start streaming
state, is also only available by adjusting the register...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add frame buffer compression on Sandybridge. The method is similar to
Ironlake, except that two new registers of type GTTMMADR must be written
with the right fence info.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Otherwise we can't really fix the abi-braindeadness of forcing
libva to manually wait for rendering when switching rings. Which
in turn makes implementing hw semaphores a pointless exercise
(at least for ironlake).
[Also added the relaxed fencing param to explain the jump in
numbering - relaxed fencing is in -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The bulk of the change is to convert the growing list of rings into an
array so that the relationship between the rings and the semaphore sync
registers can be easily computed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This makes the various rings more consistent by removing the anomalous
handing of the rendering ring execbuffer dispatch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The GATT is a write-only set of registers, reading from them in the
manner of i915_gtt_to_phys() is supposed to be undefined. However a
simple solution exists as we allocate linear memory from the stolen
area, we can simply add the block offset to the base register. As a
side-effect we recover all the unused stolen GTT entries and so enlarge
our aperture.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It isn't used for the hangcheck, which does its work right from the
timer trigger, but hangcheck can lead to error state recording, which
is run off of the workqueue.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only ever used the PRB0, neglecting the secondary ring buffers, and
now with the advent of multiple engines with separate ring buffers we
need to excise the anachronisms from our code (and be explicit about
which ring we mean where). This is doubly important in light of the
FORCEWAKE required to read ring buffer registers on SandyBridge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If modeset init failed we attempted to unload the module, before we
finished setting it up and so triggered various oopses.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After switching the MMIO registers to use pci_iomap, remember to dispose
of the mapping with pci_iounmap (for symmetry).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
So long as we adhere to the fence registers rules for alignment and no
overlaps (including with unfenced accesses to linear memory) and account
for the tiled access in our size allocation, we do not have to allocate
the full fenced region for the object. This allows us to fight the bloat
tiling imposed on pre-i965 chipsets and frees up RAM for real use. [Inside
the GTT we still suffer the additional alignment constraints, so it doesn't
magic allow us to render larger scenes without stalls -- we need the
expanded GTT and fence pipelining to overcome those...]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Eliminate the racy device unload by embedding a shrinker into each
device. Smaller, simpler code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Play safe and use the common routines which take care of the cachability
of the memory when setting up the iomapping for the PCI registers.
Whilst they should be cacheable for the current generations, actually
honouring what the device requires is a better long term strategy.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is the same value as before, but it just makes the code slightly
more readable to use the local variable than converting the aperture
size into bytes every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
At least the part that's currently enabled by the BIOS.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Preparing the ringbuffer for adding new commands can fail (a timeout
whilst waiting for the GPU to catch up and free some space). So check
for any potential error before overwriting HEAD with new commands, and
propagate that error back to the user where possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The ringbuffer keeps a pointer to the parent device, so we can use that
instead of passing around the pointer on the stack.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Based on an original patch by Zhenyu Wang, this initializes the BLT ring for
SandyBridge and enables support for user execbuffers.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... by always initialising the empty ringbuffer it is always then safe
to check whether it is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The time between start of the pixel clock and backlight enable is a basic
panel timing constraint. If the Panel Power On/Off registers are found
to be 0, assume we are booting without VBIOS initialization and set these
registers to something reasonable.
Change-Id: Ibed6cc10d46bf52fd92e0beb25ae3525b5eef99d
Signed-off-by: Bryan Freed <bfreed@chromium.org>
[ickle: rearranged into a separate function to distinguish its role from
simply parsing the VBIOS tables.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Freeing the Hardware Status Page was writing to the HWS register in
order to disable the GPU writing to the HWS page. Unfortunately, we were
writing to the mmio register after unmapping the register space, hence
the oops.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 6939a5aca7.
Daniel Vetter supplied a set of fixes for all the module unload bugs he
could trigger on his machines, so let the fun recommence!
The i915 driver has quite a few module unload bugs, the known ones at
least have fixes that are targeting 2.6.37. However, in order to
maintain a stable kernel, we should prevent this known random memory
corruption following driver unload. This should have very low impact on
normal users who are unlikely to need to unload the i915 driver.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The _DSM method on the integrated graphics device can tell us which
connectors are muxable, so add support for making the call and parsing
out the connector info.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: fix compiler warnings for using uninitialized 'result' and
downgrade error message for non-switchable devices]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A physically mapped hardware status page is allocated at driver load
time but was never freed. Call the existing code to free this page at
driver unload time on hardware which uses this kind.
Signed-off-by: Keith Packard <keithp@keithp.com>
[ickle: call before tearing down registers on KMS-only path, as pointed
out by Dave Airlie]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
lockdep spots that the fb_info->lock takes the dev->struct_mutex during
init (due to the device probing) and so we can not hold
dev->struct_mutex when unregistering the framebuffer. Simply reverse the
order of initialisation during cleanup and so do the intel_fbdev_fini()
before the intel_modeset_cleanup.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Ben Widawsky
Dave Airlie
Chris Wilson
Jan Niehusmann
Jesse Barnes
Eric Anholt
Yuanhan Liu
Daniel Vetter
Bryan Freed
Keith Packard