Граф коммитов

17 Коммитов

Автор SHA1 Сообщение Дата
Josef Bacik c1c80384c8 block: remove external dependency on wbt_flags
We don't really need to save this stuff in the core block code, we can
just pass the bio back into the helpers later on to derive the same
flags and update the rq->wbt_flags appropriately.

Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-07-09 09:07:54 -06:00
Josef Bacik a79050434b blk-rq-qos: refactor out common elements of blk-wbt
blkcg-qos is going to do essentially what wbt does, only on a cgroup
basis.  Break out the common code that will be shared between blkcg-qos
and wbt into blk-rq-qos.* so they can both utilize the same
infrastructure.

Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-07-09 09:07:54 -06:00
Omar Sandoval 544ccc8dc9 block: get rid of struct blk_issue_stat
struct blk_issue_stat squashes three things into one u64:

- The time the driver started working on a request
- The original size of the request (for the io.low controller)
- Flags for writeback throttling

It turns out that on x86_64, we have a 4 byte hole in struct request
which we can fill with the non-timestamp fields from blk_issue_stat,
simplifying things quite a bit.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-09 08:33:05 -06:00
Omar Sandoval a8a4594170 block: pass struct request instead of struct blk_issue_stat to wbt
issue_stat is going to go away, so first make writeback throttling take
the containing request, update the internal wbt helpers accordingly, and
change rwb->sync_cookie to be the request pointer instead of the
issue_stat pointer. No functional change.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-09 08:33:02 -06:00
Omar Sandoval 934031a129 block: move some wbt helpers to blk-wbt.c
A few helpers are only used from blk-wbt.c, so move them there, and put
wbt_track() behind the CONFIG_BLK_WBT typedef. This is in preparation
for changing how the wbt flags are tracked.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-09 08:33:00 -06:00
Jens Axboe 782f569774 blk-wbt: throttle discards like background writes
Throttle discards like we would any background write. Discards should
be background activity, so if they are impacting foreground IO, then
we will throttle them down.

Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-08 15:11:02 -06:00
Jens Axboe 8bea609019 blk-wbt: pass in enum wbt_flags to get_rq_wait()
This is in preparation for having more write queues, in which
case we would have needed to pass in more information than just
a simple 'is_kswapd' boolean.

Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-08 15:10:56 -06:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Jan Kara 8330cdb0fe block: Make writeback throttling defaults consistent for SQ devices
When CFQ is used as an elevator, it disables writeback throttling
because they don't play well together. Later when a different elevator
is chosen for the device, writeback throttling doesn't get enabled
again as it should. Make sure CFQ enables writeback throttling (if it
should be enabled by default) when we switch from it to another IO
scheduler.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-19 08:49:03 -06:00
Shaohua Li 88eeca495b block: track request size in blk_issue_stat
Currently there is no way to know the request size when the request is
finished. Next patch will need this info. We could add extra field to
record the size, but blk_issue_stat has enough space to record it, so
this patch just overloads blk_issue_stat. With this, we will have 49bits
to track time, which still is very long time.

Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-03-28 08:02:20 -06:00
Omar Sandoval 34dbad5d26 blk-stat: convert to callback-based statistics reporting
Currently, statistics are gathered in ~0.13s windows, and users grab the
statistics whenever they need them. This is not ideal for both in-tree
users:

1. Writeback throttling wants its own dynamically sized window of
   statistics. Since the blk-stats statistics are reset after every
   window and the wbt windows don't line up with the blk-stats windows,
   wbt doesn't see every I/O.
2. Polling currently grabs the statistics on every I/O. Again, depending
   on how the window lines up, we may miss some I/Os. It's also
   unnecessary overhead to get the statistics on every I/O; the hybrid
   polling heuristic would be just as happy with the statistics from the
   previous full window.

This reworks the blk-stats infrastructure to be callback-based: users
register a callback that they want called at a given time with all of
the statistics from the window during which the callback was active.
Users can dynamically bucketize the statistics. wbt and polling both
currently use read vs. write, but polling can be extended to further
subdivide based on request size.

The callbacks are kept on an RCU list, and each callback has percpu
stats buffers. There will only be a few users, so the overhead on the
I/O completion side is low. The stats flushing is also simplified
considerably: since the timer function is responsible for clearing the
statistics, we don't have to worry about stale statistics.

wbt is a trivial conversion. After the conversion, the windowing problem
mentioned above is fixed.

For polling, we register an extra callback that caches the previous
window's statistics in the struct request_queue for the hybrid polling
heuristic to use.

Since we no longer have a single stats buffer for the request queue,
this also removes the sysfs and debugfs stats entries. To replace those,
we add a debugfs entry for the poll statistics.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-03-21 10:03:11 -06:00
Jens Axboe d62118b6dd blk-wbt: allow wbt to be enabled always through sysfs
Currently there's no way to enable wbt if it's not enabled in the
kernel config by default for a device. Allow a write to the
'wbt_lat_usec' queue sysfs file to enable wbt.

This is useful for both the kernel config case, but also if the
device is CFQ managed and it was turned off by default.

Signed-off-by: Jens Axboe <axboe@fb.com>
2016-11-28 10:27:03 -07:00
Jens Axboe fa224eed2b blk-wbt: cleanup disable-by-default for CFQ
Make it clear that we are disabling wbt for the specified queued,
if it was enabled by default. This is in preparation for allowing
users to re-enable wbt, and not have it disabled automatically
again.

Signed-off-by: Jens Axboe <axboe@fb.com>
2016-11-28 10:27:03 -07:00
Jens Axboe 80e091d10e blk-wbt: allow reset of default latency through sysfs
Allow a write of '-1' to reset the default latency target for
a given device. This removes knowledge of the different default
settings for rotational vs non-rotational from user space.

Signed-off-by: Jens Axboe <axboe@fb.com>
2016-11-28 10:27:03 -07:00
Jens Axboe 8054b89f8f blk-wbt: remove stat ops
Again a leftover from when the throttling code was generic. Now that we
just have the block user, get rid of the stat ops and indirections.

Signed-off-by: Jens Axboe <axboe@fb.com>
2016-11-11 16:18:24 -07:00
Jens Axboe d8a0cbfd73 blk-wbt: store queue instead of bdi
The bdi was a leftover from when the code was block layer agnostic.
Now that we just support a block layer user, store the queue directly.

Signed-off-by: Jens Axboe <axboe@fb.com>
2016-11-11 16:18:18 -07:00
Jens Axboe e34cbd3074 blk-wbt: add general throttling mechanism
We can hook this up to the block layer, to help throttle buffered
writes.

wbt registers a few trace points that can be used to track what is
happening in the system:

wbt_lat: 259:0: latency 2446318
wbt_stat: 259:0: rmean=2446318, rmin=2446318, rmax=2446318, rsamples=1,
               wmean=518866, wmin=15522, wmax=5330353, wsamples=57
wbt_step: 259:0: step down: step=1, window=72727272, background=8, normal=16, max=32

This shows a sync issue event (wbt_lat) that exceeded it's time. wbt_stat
dumps the current read/write stats for that window, and wbt_step shows a
step down event where we now scale back writes. Each trace includes the
device, 259:0 in this case.

Signed-off-by: Jens Axboe <axboe@fb.com>
2016-11-10 13:53:32 -07:00