With the recent primary-plane changes for drm, the primary plane's
framebuffer needs to be ref counted the same way as for
non-primary-planes. This was not done by the omapdrm driver, which
caused the ref count to drop to 0 too early, causing problems.
This patch moves the fb unref and ref from omap_plane_update to
omap_plane_mode_set. This way the fb refs are updated for both primary
and non-primary cases, as omap_plane_update calls omap_plane_mode_set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vblank_cb callback and the page_flip ioctl can occur together in different
CPU contexts. vblank_cb uses takes tje drm device's event_lock spinlock when
sending the vblank event and updating omap_crtc->event and omap_crtc->od_fb.
Use the same spinlock in page_flip, to make sure the above omap_crtc parameters
are configured sequentially.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_crtc->old_fb is used to check whether the previous page flip has completed
or not. However, it's never initialized to anything, so it's always NULL. This
results in the check to always succeed, and the page_flip to proceed.
Initialize old_fb to the fb that we intend to flip to through page_flip, and
therefore prevent a future page flip to proceed if the last one didn't
complete.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The channel_names list didn't have a string populated for LCD3 manager, this
results in a crash when the display's output is connected to LCD3. Add an entry
for LCD3.
Reported-by: Somnath Mukherjee <somnath@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A waiter of the type OMAP_GEM_READ should wait for a buffer to be completely
written, and only then proceed with reading it. A similar logic applies for
waiters with OMAP_GEM_WRITE flag.
Currently the function is_waiting() waits on the read_complete/read_target
counts in the sync object.
This should be the other way round, as a reader should wait for users who are
'writing' to this buffer, and vice versa.
Make readers of the buffer(OMAP_GEM_READ) wait on the write counters, and
writers to the buffer(OMAP_GEM_WRITE) wait on the read counters in is_waiting()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In omap_gem_op_async(), if a waiter is not added to the wait list, it needs to
be free'd in the function itself.
Make sure we free the waiter for this case.
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Patch dfe96ddcfa (omapdrm: simplify locking in
the fb debugfs file) removed taking locks when using omapdrm's debugfs
to dump fb objects.
However, in omap_gem_describe we give a WARN is the lock has not been
taken, so that WARN is now seen every time omapdrm debugfs is used.
So, presuming the removal of locks is ok, we can also remove the WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the planes, including primary planes, are now destroyed by the drm
framework. Thus we no longer need the explicit call to plane->destroy
from the crtc's destroy function.
This patch removes the call, thus fixing the crash caused by double
freeing the plane.
remove omap_crtc->plane->funcs->destroy(omap_crtc->plane)
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Print a warning when the user tries to rotate a non-TILER framebuffer.
Also set the rotation to 0, to avoid constant flood of the warnings in
case of page flipping.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_fbdev_create() takes a reference to the fb's gem object with
omap_gem_get_paddr(). However, it never releases it with
omap_gem_put_paddr().
This patch adds the missing omap_gem_put_paddr() to omap_fbdev_free().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Plane rotation with omapdrm is currently broken.
It seems omap_plane_mode_set() expects width and height in screen
coordinates, so pass it like that.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment the omap_crtc_pre_apply() handles the enabling, disabling
and configuring of encoders and panels separately from the CRTC (i.e.
the overlay manager).
However, this doesn't work correctly. The encoder driver has to be in
control of its video input (i.e. the crtc) for correct operation.
This problem causes bugs with (at least) HDMI: the HDMI encoder supplies
pixel clock for DISPC, and DISPC supplies video stream for HDMI. The
current code first enables the HDMI encoder, and CRTC after that.
However, the encoder expects the video stream to start during the
encoder's enable, and if it doesn't, there will be sync lost errors.
The encoder enables its video source by calling src->enable(), and this
call goes to omapdrm (omap_crtc_enable), but omapdrm doesn't do anything
in that function. Similarly for disable, which goes to
omap_crtc_disable().
This patch moves the code to setup and enable/disable the crtc to
omap_crtc_enable. and omap_crtc_disable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
When an encoder is no longer connected to a crtc, the driver will leave
the encoder enabled.
This patch adds code to track the encoder used for a crtc, and when the
encoder changes, the old one is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At module unload, omap_fbdev_free() gets called which releases the
framebuffers. However, the framebuffers are still used by crtcs, and
will be released only later at vsync. The driver doesn't wait for this,
and goes on to release the rest of the resources, which often
causes a crash.
This patchs adds a omap_crtc_flush() function which waits until the crtc
has finished with its apply queue and page flips.
The function utilizes a simple polling while-loop, as the performance is
not an issue here.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At the moment the DMM driver is never unregistered, even if it's
registered in the omapdrm module's init function. This means we'll get
errors when reloading the omapdrm module.
Fix this by unregistering the DMM driver properly, and also change the
module init to fail if DMM driver cannot be registered, simplifying the
unregister path as we don't need to keep the state whether we registered
the DMM driver or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
When unloading omapdrm driver, the omapdrm platform device is
uninitialized last, after the displays have been disconnected omap_crtc
callbacks have been removed. As the omapdrm pdev uninitialization needs
the features uninitialized in earlier steps, a crash is guaranteed.
This patch fixes the uninitialize order so that the omapdrm pdev is
removed first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At the moment it's quite easy to get the following errors when the HDMI
output is enabled or disabled:
[drm:omap_crtc_error_irq] *ERROR* tv: errors: 00008000
The reason for the errors is that the omapdrm driver doesn't properly
handle the sync-lost irqs that happen when enabling the DIGIT crtc,
which is used for HDMI and analog TV. The driver does disable the
sync-lost irq properly, but it fails to wait until the output has been
fully enabled (i.e. the first vsync), so the sync-lost errors are still
seen occasionally.
This patch makes the omapdrm act the same way as the omapfb does:
- When enabling a display, we'll wait for the first vsync.
- When disabling a display, we'll wait for framedone if available, or
odd and even vsyncs.
These changes make sure the output is fully enabled or disabled at the
end of the function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Sanjay Singh Rawat <sanjay.rawat@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
drm/omap: Don't dereference list head when the connectors list is empty
drm/msm/mdp: add timeout for irq wait
drm/msm: validate flags, etc
drm/msm: use componentised device support
drm/msm: add chip-id param
drm/msm: crank down gpu when inactive
drm/msm: spin helper
drm/msm: add hang_debug module param
drm/msm: hdmi audio support
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
The connectors list iterator returns the list head when the list is
empty. Fix it by returning NULL in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DRM drivers share a common address_space across all character-devices of a
single DRM device. This allows simple buffer eviction and mapping-control.
However, DRM core currently waits for the first ->open() on any char-dev
to mark the underlying inode as backing inode of the device. This delayed
initialization causes ugly conditions all over the place:
if (dev->dev_mapping)
do_sth();
To avoid delayed initialization and to stop reusing the inode of the
char-dev, we allocate an anonymous inode for each DRM device and reset
filp->f_mapping to it on ->open().
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
omapdss has its own video-timings struct, but we want to move the common
videomode.
The first step is to change the omapdss's pixelclock unit from kHz to
Hz. Also, omapdss uses "pixel_clock" field name, whereas the common
videomode uses "pixelclock" field name. This patch changes the field
name also, as that makes it easy to spot any non-converted pixel_clock
uses.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=/Uwk
-----END PGP SIGNATURE-----
Merge tag 'omapdrm-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm patches for 3.14
* tag 'omapdrm-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
drm/omap: Enable DT support for DMM
drm/omap: fix: change dev_unload order
drm/omap: fix: disable encoder before destroying it
drm/omap: fix: disconnect devices when omapdrm module is removed
drm/omap: fix: Defer probe if an omapdss device requests for it at connect
drm/omap: fix (un)registering irqs inside an irq handler
Conflicts:
drivers/gpu/drm/omapdrm/omap_drv.c
This was hidden in a generic void * dev->mm_private. But only ever
used for gem. But thanks to this fake generic pretension no one
noticed that Rob's drm drivers are now all broken.
So just give the offset manager a type pointer and fix up msm, omapdrm
and tilcdc.
v2: Fixup compile fail.
v3: Fixup rebase fail that David spotted.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Enable use of DT for DMM/Tiler.
Originally worked on by Andy Gross <andygro@gmail.com>
Cc: Andy Gross <andygro@gmail.com>
Cc: DRI Development <dri-devel@lists.freedesktop.org>
Signed-off-by: Archit Taneja <archit@ti.com>
[tomi.valkeinen@ti.com: use of_match_ptr()]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current dev_unload order uninits the irqs too early.
In the current sequence, it's possible that a crtc queues work(apply_worker)
to display a buffer, which registers to omap_crtc_apply_irq to notfiy the
completion of the configuration we applied.
Calling drm_vblank_cleanup and omap_drm_irq_uninstall here causes the crtc's
apply handler to never get called, which results in an incorrect state of the
apply_irq.registered parameter.
This condition occurs where there is no mode set via omapdrm, and dev_lastclose
tries to set a default fb mode via drm_fb_helper_restore_fbdev_mode. The apply
work scheduled by restore_fbdev_mode is very close in time to the disabling of
the irq handler, and hence leads to a race condition. We move the irq cleanup
at the end of the unload sequence to prevent this.
Also, the call to flush_workqueue is removed since it's called internally by
destroy_workqueue.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, an encoder is disabled only when an apply work is queued for the
corresponding crtc. This works fine for the paths where userspace explicitly
disables crtc, this results in disabling the omapdss device in the crtc's
pre_apply function.
However, when the omapdrm module is removed, there is no work queued to ensure
that the encoder is disabled. This can result in an enabled omapdss device when
removing omapdrm. omapdss is left in an inconsistent state, and that prevents us
from using that omapdss device being used again.
Disable enabled encoders in omap_encoder_destroy, we could consider a better
place for doing this later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At omapdrm probe, we install manager ops and connect omapdss devices. This
needs to be undone when omapdrm module is removed so that omapdss is in a
clean state. This ensures that we can re-insert omapdrm module, or some other
module which uses omapdss(like omapfb/omap_vout).
Currently, omapdrm's remove neither uninstalls manager ops, or disconnects
omapdss devices. We make sure that this is done in pdev_remove.
omapdrm establishes connections for omap_dss_device devices when probed. It
should also be responsible to disconnect the devices. Keeping the devices
connected can prevent the panel driver modules from unloading, it also causes
issues when we try to remove or re-insert omapdrm module.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the omapdss device model changes. omapdrm is required to call dssdriver's
connect() op to register a panel. This is currently done in omap_modeset_init()
A call to connect() can fail if the omapdss panels or the encoders(HDMI/DPI)
they connect to have some resource(like regulators, I2C adapter) missing. If
this happens, the correct approach is to defer omapdrm's probe.
omapdrm currently ignores those panels which return a non zero value when
connected. This could result in omapdrm ignoring all panels on an omap board.
The right approach would be for omapdrm to request for probe deferral when a
panel's connect op returns -EPROBE_DEFER.
In order to do this, we need to call connect() much earlier during omapdrm's
probe to prevent too many things are already done by then. We now connect the
panels during pdev_probe(), before anything else is initialized, so that we
don't need to undo too many things if a defer was requested.
Now when we enter omap_modeset_init(), we have a set of panels that have been
connected. We now proceed with registering only those panels that are already
connected.
A special case has to be considered when no panels are available to connect when
omapdrm probes. In this case too, we defer probe and expect that a panel will be
available to connect the next time.
Checking whether the panel has a driver or whether it has get_timing/read_edid
ops in omap_modeset_init() are redundant with the new display model. These can
be removed since a dssdev device will always have a driver associated with it,
and all dssdev drivers have a get_timings op.
This will mainly fix cases when omapdrm is built-in the kernel, since that's
generally where resources like regulators or I2C are unavailable because of
probe order dependencies.
In particular this fixes boot with omapdrm built-in on an omap4 panda ES board.
The regulators used by HDMI(provided by I2C based TWL regulators) aren't
initialized because I2C isn't initialized, I2C isn't initialized as it's pins
are not configured because pinctrl is yet to probe.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm (un)registers irqs inside an irq handler. The problem is that
the (un)register function uses dispc_runtime_get/put() to enable the
clocks, and those functions are not irq safe by default.
This was kind of fixed in 48664b21ae
(OMAPDSS: DISPC: set irq_safe for runtime PM), which makes dispc's
runtime calls irq-safe.
However, using pm_runtime_irq_safe in dispc makes the parent of dispc,
dss, always enabled, effectively preventing PM for the whole DSS module.
This patch makes omapdrm behave better by adding new irq (un)register
functions that do not use dispc_runtime_get/put, and using those
functions in interrupt context. Thus we can make dispc again
non-irq-safe, allowing proper PM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
I've killed them a long time ago in drm/i915, let's get rid of this
remnant of shared drm core days for good.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Again omap already sets the driver data pointer to the drm_device.
Also drop the driver unregister call, that should be (and already is)
done in the module unload hook.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not all drivers will need take all the modeset locks for dirtyfb, so
push the locking down to the drivers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm updates from Dave Airlie:
"This is a combo of -next and some -fixes that came in in the
intervening time.
Highlights:
New drivers:
ARM Armada driver for Marvell Armada 510 SOCs
Intel:
Broadwell initial support under a default off switch,
Stereo/3D HDMI mode support
Valleyview improvements
Displayport improvements
Haswell fixes
initial mipi dsi panel support
CRC support for debugging
build with CONFIG_FB=n
Radeon:
enable DPM on a number of GPUs by default
secondary GPU powerdown support
enable HDMI audio by default
Hawaii support
Nouveau:
dynamic pm code infrastructure reworked, does nothing major yet
GK208 modesetting support
MSI fixes, on by default again
PMPEG improvements
pageflipping fixes
GMA500:
minnowboard SDVO support
VMware:
misc fixes
MSM:
prime, plane and rendernodes support
Tegra:
rearchitected to put the drm driver into the drm subsystem.
HDMI and gr2d support for tegra 114 SoC
QXL:
oops fix, and multi-head fixes
DRM core:
sysfs lifetime fixes
client capability ioctl
further cleanups to device midlayer
more vblank timestamp fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (789 commits)
drm/nouveau: do not map evicted vram buffers in nouveau_bo_vma_add
drm/nvc0-/gr: shift wrapping bug in nvc0_grctx_generate_r406800
drm/nouveau/pwr: fix missing mutex unlock in a failure path
drm/nv40/therm: fix slowing down fan when pstate undefined
drm/nv11-: synchronise flips to vblank, unless async flip requested
drm/nvc0-: remove nasty fifo swmthd hack for flip completion method
drm/nv10-: we no longer need to create nvsw object on user channels
drm/nouveau: always queue flips relative to kernel channel activity
drm/nouveau: there is no need to reserve/fence the new fb when flipping
drm/nouveau: when bailing out of a pushbuf ioctl, do not remove previous fence
drm/nouveau: allow nouveau_fence_ref() to be a noop
drm/nvc8/mc: msi rearm is via the nvc0 method
drm/ttm: Fix vma page_prot bit manipulation
drm/vmwgfx: Fix a couple of compile / sparse warnings and errors
drm/vmwgfx: Resource evict fixes
drm/edid: compare actual vrefresh for all modes for quirks
drm: shmob_drm: Convert to clk_prepare/unprepare
drm/nouveau: fix 32-bit build
drm/i915/opregion: fix build error on CONFIG_ACPI=n
Revert "drm/radeon/audio: don't set speaker allocation on DCE4+"
...
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For drivers which might want to disable fbdev legacy support.
Select the new option in all drivers for now, so this shouldn't result
in any change. Drivers need some work anyway to make fbdev support
optional (if they have it implemented, that is), so the recommended
way to expose this is by adding per-driver options. At least as long
as most drivers don't support disabling the fbdev support.
v2: Update for new drm drivers msm and rcar-du. Note that Rob's msm
driver can already take advantage of this, which allows us to build
msm without any fbdev depencies in the kernel!
v3: Move the MODULE_* stuff from the fbdev helper file to
drm_crtc_helper.c.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
irq_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_vblank_init() is too ugly. Make it a bit easier on the eye by
collecting all the per-crtc vblank counters, timestamps etc. to
a structure and just allocate an array of those.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vblank_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm tree changes from Dave Airlie:
"This is the main drm pull request, I have some overlap with sound and
arm-soc, the sound patch is acked and may conflict based on -next
reports but should be a trivial fixup, which I'll leave to you!
Highlights:
- new drivers:
MSM driver from Rob Clark
- non-drm:
switcheroo and hdmi audio driver support for secondary GPU
poweroff, so drivers can use runtime PM to poweroff the GPUs. This
can save 5 or 6W on some optimus laptops.
- drm core:
combined GEM and TTM VMA manager
per-filp mmap permission tracking
initial rendernode support (via a runtime enable for now, until we get api stable),
remove old proc support,
lots of cleanups of legacy code
hdmi vendor infoframes and 4k modes
lots of gem/prime locking and races fixes
async pageflip scaffolding
drm bridge objects
- i915:
Haswell PC8+ support and eLLC support, HDMI 4K support, initial
per-process VMA pieces, watermark reworks, convert to generic hdmi
infoframes, encoder reworking, fastboot support,
- radeon:
CIK PM support, remove 3d blit code in favour of DMA engines,
Berlin GPU support, HDMI audio fixes
- nouveau:
secondary GPU power down support for optimus laptops, lots of
fixes, use MSI, VP3 engine support
- exynos:
runtime pm support for g2d, DT support, remove non-DT,
- tda998x i2c driver:
lots of fixes for sync issues
- gma500:
lots of cleanups
- rcar:
add LVDS support, fbdev emulation,
- tegra:
just minor fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (684 commits)
drm/exynos: Fix build error with exynos_drm_connector.c
drm/exynos: Remove non-DT support in exynos_drm_fimd
drm/exynos: Remove non-DT support in exynos_hdmi
drm/exynos: Remove non-DT support in exynos_drm_g2d
drm/exynos: Remove non-DT support in exynos_hdmiphy
drm/exynos: Remove non-DT support in exynos_ddc
drm/exynos: Make Exynos DRM drivers depend on OF
drm/exynos: Consider fallback option to allocation fail
drm/exynos: fimd: move platform data parsing to separate function
drm/exynos: fimd: get signal polarities from device tree
drm/exynos: fimd: replace struct fb_videomode with videomode
drm/exynos: check a pixel format to a particular window layer
drm/exynos: fix fimd pixel format setting
drm/exynos: Add NULL pointer check
drm/exynos: Remove redundant error messages
drm/exynos: Add missing of.h header include
drm/exynos: Remove redundant NULL check in exynos_drm_buf
drm/exynos: add device tree support for rotator
drm/exynos: Add missing includes
drm/exynos: add runtime pm interfaces to g2d driver
...
In the old panel device model we had "outputs", which were the encoders
inside OMAP DSS block, and panel devices (omap_dss_device). The panel
devices had a reference to the source of the video data, i.e. reference
to an "output", in a field named "output".
That was somewhat confusing even in the old panel device model, but even
more so with the panel device model where we can have longer chains of
display entities.
This patch renames the "output" field to "src", which much better tells
what the field points to.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
This lets drivers see the flags requested by the application
[airlied: fixup for rcar/imx/msm]
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
We're taking the sizeof() the wrong thing so it doesn't clear the whole
buffer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
And simplify how we hold a ref+pin to what is being scanned out by using
fb refcnt'ing. The previous logic pre-dated fb refcnt, and as a result
was less straightforward than it could have been. By holding a ref to
the fb, we don't have to care about how many plane's there are and
holding a ref to each color plane's bo.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
So I've stumbled over drm_fasync and wondered what it does. Digging
that up is quite a story.
First I've had to read up on what this does and ended up being rather
bewildered why peopled loved signals so much back in the days that
they've created SIGIO just for that ...
Then I wondered how this ever works, and what that strange "No-op."
comment right above it should mean. After all calling the core fasync
helper is pretty obviously not a noop. After reading through the
kernels FASYNC implementation I've noticed that signals are only sent
out to the processes attached with FASYNC by calling kill_fasync.
No merged drm driver has ever done that.
After more digging I've found out that the only driver that ever used
this is the so called GAMMA driver. I've frankly never heard of such a
gpu brand ever before. Now FASYNC seems to not have been the only bad
thing with that driver, since Dave Airlie removed it from the drm
driver with prejudice:
commit 1430163b4bbf7b00367ea1066c1c5fe85dbeefed
Author: Dave Airlie <airlied@linux.ie>
Date: Sun Aug 29 12:04:35 2004 +0000
Drop GAMMA DRM from a great height ...
Long story short, the drm fasync support seems to be doing absolutely
nothing. And the only user of it was never merged into the upstream
kernel. And we don't need any fops->fasync callback since the fcntl
implementation in the kernel already implements the noop case
correctly.
So stop this particular cargo-cult and rip it all out.
v2: Kill drm_fasync assignments in rcar (newly added) and imx drivers
(somehow I've missed that one in staging). Also drop the reference in
the drm DocBook. ARM compile-fail reported by Rob Clark.
v3: Move the removal of dev->buf_asnyc assignment in drm_setup to this
patch here.
v4: Actually git add ... tsk.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
KMS drivers really shouldn't need to do anything on firstopen, so kill
empty callbacks.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tomi Valkeinen
Archit Taneja
Subhajit Paul
Grazvydas Ignotas
Linus Torvalds
Dave Airlie
Matt Roper
Laurent Pinchart
David Herrmann
Daniel Vetter
Ville Syrjälä
Russell King
Keith Packard
Dan Carpenter
Rob Clark