This patch adds a driver for the I2C controller found on the MediaTek
MT7621/7628/7688 SoC's. The base version of this driver was done by
Steven Liu (according to the copyright and MODULE_AUTHOR lines). It
can be found in the OpenWRT repositories (v4.14 at the time I looked).
The base driver had many issues, which are disccussed here:
https://en.forum.labs.mediatek.com/t/openwrt-15-05-loads-non-working-i2c-kernel-module-for-mt7688/1286/3
>From this link an enhanced driver version (complete rewrite, mayor
changes: support clock stretching, repeated start, ACK handling and
unlimited message length) from Jan Breuer can be found here:
https://gist.github.com/j123b567/9b555b635c2b4069d716b24198546954
This patch now adds this enhanced I2C driver to mainline.
Changes by Stefan Roese for upstreaming:
- Add devicetree bindings
- checkpatch clean
- Use module_platform_driver()
- Minor cosmetic enhancements
- Removed IO warpped functions
- Use readl_relaxed_poll_timeout() and drop poll_down_timeout()
- Removed superfluous barrier() in mtk_i2c_reset()
- Use i2c_8bit_addr_from_msg()
- Added I2C_FUNC_PROTOCOL_MANGLING
- Removed adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
MP2 controllers have two separate busses, so may accommodate up to two I2C
adapters. Those adapters are listed in the ACPI namespace with the
"AMDI0011" HID, and probed by a platform driver.
Communication with the MP2 takes place through MMIO registers, or through
DMA for more than 32 bytes transfers.
This is major rework of the patch submitted by Nehal-bakulchandra Shah from
AMD (https://patchwork.kernel.org/patch/10597369/).
Most of the event handling of v3 was rewritten to make it work with more
than one bus (e.g on Ryzen-based Lenovo Yoga 530), and this version
contains many other improvements.
Signed-off-by: Elie Morisse <syniurge@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Slave mode driver is based on the concept of i2c-designware driver.
Signed-off-by: Juergen Fitschen <me@jue.yt>
[ludovic.desroches@microchip.com: rework Kconfig and replace IS_ENABLED
by defined]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The single file i2c-at91.c has been split into core code (i2c-at91-core.c)
and master mode specific code (i2c-at91-master.c). This should enhance
maintainability and reduce ifdeffery for slave mode related code.
The code itself hasn't been touched. Shared functions only had to be made
non-static. Furthermore, includes have been cleaned up.
Signed-off-by: Juergen Fitschen <me@jue.yt>
[ludovic.desroches@microchip.com: fix checkpatch errors and use SPDX]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Latest NVIDIA GPU card has USB Type-C interface. There is a
Type-C controller which can be accessed over I2C.
This driver adds I2C bus driver to communicate with Type-C controller.
I2C client driver will be part of USB Type-C UCSI driver.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[wsa: kept Makefile sorting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This bus driver supports the GENI based i2c hardware controller in the
Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
module supporting a wide range of serial interfaces including I2C. The
driver supports FIFO mode and DMA mode of transfer and switches modes
dynamically depending on the size of the transfer.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
[wsa: squashed the MAINTAINER addition and a RPM fix by Evan Green]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add register definitions for FSI-attached I2C master and functions to
access those registers over FSI. Add an FSI driver so that our I2C bus
is probed up during an FSI scan.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
-I2C core now reports proper OF style module alias. I'd like to repeat
the note from the commit msg here (Thanks, Javier!):
NOTE: This patch may break out-of-tree drivers that were relying
on this behavior, and only had an I2C device ID table even
when the device was registered via OF.
There are no remaining drivers in mainline that do this, but
out-of-tree drivers have to be fixed and define a proper OF
device ID table to have module auto-loading working.
- new driver for the SynQuacer I2C controller
- major refactoring of the QUP driver
- the piix4 driver now uses request_muxed_region which should fix a
long standing resource conflict with the sp5100_tco watchdog
- a bunch of small core & driver improvements
* 'i2c/for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (53 commits)
i2c: add support for Socionext SynQuacer I2C controller
dt-bindings: i2c: add binding for Socionext SynQuacer I2C
i2c: Update i2c_trace_msg static key to modern api
i2c: fix parameter of trace_i2c_result
i2c: imx: avoid taking clk_prepare mutex in PM callbacks
i2c: imx: use clk notifier for rate changes
i2c: make i2c_check_addr_validity() static
i2c: rcar: fix mask value of prohibited bit
dt-bindings: i2c: document R8A77965 bindings
i2c: pca-platform: drop gpio from platform data
i2c: pca-platform: use device_property_read_u32
i2c: pca-platform: unconditionally use devm_gpiod_get_optional
sh: sh7785lcr: add GPIO lookup table for i2c controller reset
i2c: qup: reorganization of driver code to remove polling for qup v2
i2c: qup: reorganization of driver code to remove polling for qup v1
i2c: qup: send NACK for last read sub transfers
i2c: qup: fix buffer overflow for multiple msg of maximum xfer len
i2c: qup: change completion timeout according to transfer length
i2c: qup: use the complete transfer length to choose DMA mode
i2c: qup: proper error handling for i2c error in BAM mode
...
This is a cleaned up version of the I2C controller driver for
the Fujitsu F_I2C IP, which was never supported upstream, and
has now been incorporated into the Socionext SynQuacer SoC.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[wsa: updated MAINTAINERS entry and removed two empty lines]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The blackfin architecture is getting removed, so the
twi driver can also be removed.
Acked-by: Aaron Wu <aaron.wu@analog.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds initial support for the STM32F7 I2C controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add driver support for the Altera I2C Controller. The I2C
controller is soft IP for use in FPGAs.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the I2C controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Intel Cherry Trail Whiskey Cove PMIC does not contain a builtin
battery charger, instead boards with this PMIC use an external TI
bq24292i charger IC, which is connected to a SMBUS controller built into
the PMIC.
This commit adds an i2c-bus driver for the PMIC's builtin SMBUS
controller. The probe function for this i2c-bus will also register an
i2c-client for the TI bq24292i charger after the i2c-bus has been
registered.
Note that several device-properties are set on the client-device to
tell the bq24190 power-supply driver to integrate the Whiskey Cove PMIC
and e.g. use the PMIC's BC1.2 detection (through extcon) to determine
the maximum input current.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Changes in Kconfig to enable I2C_DESIGNWARE_SLAVE support
- Slave functions added to core library file
- Slave abort sources added to common source file
- New driver: i2c-designware-slave added
- Changes in the Makefile to compile the I2C_DESIGNWARE_SLAVE module
when supported by the architecture.
All the SLAVE flow is added but it is not enabled via platform
driver.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made a function static and one-lined a message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds i2c controller driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added initial master support for Aspeed I2C controller. Supports
fourteen busses present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- The functions related to I2C master mode of operation were transformed
in a single driver.
- Common definitions were moved to i2c-designware-core.h
- The i2c-designware-core is now only a library file, the functions
associated are in a source file called i2c-designware-common and
are used by both i2c-designware-master and i2c-designware-slave.
- To decrease noise in namespace common i2c_dw_*() functions are
now using ops to keep them private.
- Designware PCI driver had to be changed to match the previous ops
functions implementation.
Almost all of the "core" source is now part of the "master" source. The
difference is the functions used by both modes and they are in the
"common" source file.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add Tegra BPMP I2C driver. The BPMP is the boot and power management
processor embedded in Tegra SoCs. In newer SoC versions, access to one
of the I2C busses goes via the BPMP, requiring a different "proxy" I2C
driver that accesses the bus via the real I2C driver embedded in the
BPMP firmware.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the STM32F4 I2C controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds lpi2c bus driver to support new i.MX products
which use lpi2c instead of the old imx i2c.
The lpi2c can continue operating in stop mode when an appropriate
clock is available. It is also designed for low CPU overhead with
DMA offloading of FIFO register accesses.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Fugang Duan <B38611@freescale.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Device driver for Mellanox I2C controller logic, implemented in Lattice
CPLD device.
Device supports:
- Master mode
- One physical bus
- Polling mode
The Kconfig currently controlling compilation of this code is:
drivers/i2c/busses/Kconfig:config I2C_MLXCPLD
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ThunderX SOC uses the same i2c block as the Octeon SOC.
The main difference is that on ThunderX the device is a PCI device
so device probing is done via PCI, interrupts are MSI-X. The
clock rates can be set via device tree or ACPI.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move common functionality into a separate file in preparation of the
re-use from the ThunderX i2c driver.
Functions are slightly re-ordered but no other changes are included.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is an intermediate commit in preparation of the driver split.
The module rename in this commit will be reverted in the next patch,
this is just done to make the series bisectible.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc. This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc. This adapter is so simple that
it has no FIFO in it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.
The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add an I2C bus driver i2c-xlp9xx.c to support the I2C block in the
XLP9xx/XLP5xx MIPS SoC. Update Kconfig and Makefile to add the
CONFIG_I2C_XLP9XX option.
Signed-off-by: Subhendu Sekhar Behera <sbehera@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adds the i2c bus controller driver for the Ingenic JZ4780 SoC.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The CX92755 is an SoC in the Conexant Digicolor series. The devicetree binding
document describes the I2C controller on the CX92755 SoC, that is also shared
by some other SoCs in the Digicolor series. The driver adds support.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
[wsa: fixed spaces around operators]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add initial support to the Broadcom iProc I2C controller found in the
iProc family of SoCs.
The iProc I2C controller has separate internal TX and RX FIFOs, each has
a size of 64 bytes. The iProc I2C controller supports two bus speeds
including standard mode (100kHz) and fast mode (400kHz)
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch implements an I2C bus sharing mechanism between the host and platform
hardware on select Intel BayTrail SoC platforms using the X-Powers AXP288 PMIC.
On these platforms access to the PMIC must be shared with platform hardware. The
hardware unit assumes full control of the I2C bus and the host must request
access through a special semaphore. Hardware control of the bus also makes it
necessary to disable runtime pm to avoid interfering with hardware transactions.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The highlight is the series that reworks the idle management on powernv, which
allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!" problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he asked that we
take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of the audit
maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a sysfs file,
so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for smt-enabled, and
the patch to add __force to get_user() so we can use bitwise types.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GXdK
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
The patch exposes the available i2c busses on the PowerNV platform
to the kernel and implements the bus driver to support i2c and
smbus commands.
The driver uses the platform device infrastructure to probe the busses
on the platform and registers them with the i2c driver framework.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> (I2C part, excluding the bindings)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is a driver for the I2C controller found in Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the IMG I2C Serial Control Bus (SCB) found on the
Pistachio and TZ1090 SoCs.
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
[Ezequiel: code cleaning and rebasing]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
[Lee: Fixed some whitespace issues in Kconfig]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: Wei Yan <sledge.yanwei@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C bus driver for the controller found in the LSI Axxia family SoCs. The
driver implements 10-bit addressing and SMBus transfer modes via emulation
(including SMBus block data read).
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver is marked as deprecated since the pre-git era. Any user
left(?) should really have switched to i2c-gpio meanwhile.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
It turned out that the s6000 simply has a designware IP core and should
use the designated driver for it which is way more maintained and
feature complete. There are currently no users in tree, and not even a
toolchain for s6000 seems to be available. So, simply remove this
duplicate. If someone needs assistance in converting to the designware
driver, the i2c list will be there to help.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Stefan Roese
Elie Morisse
Juergen Fitschen
Juergen Fitschen
Ajay Gupta
Manivannan Sadhasivam
Karthikeyan Ramasubramanian
Eddie James
Pierre-Yves MORDRET
Linus Torvalds
Ard Biesheuvel
Arnd Bergmann
Greg Kroah-Hartman
Thor Thayer
Baolin Wang
Hans de Goede
Luis Oliveira
Baoyou Xie
Brendan Higgins
Shardar Shariff Md
M'boumba Cedric Madianga
Gao Pan
Vadim Pasternak
Jan Glauber
Masahiro Yamada
Joachim Eastwood
Wolfram Sang
Kamal Dasu
Xudong Chen
Feng Kan
Subhendu Sekhar Behera
Zubair Lutfullah Kakakhel
Baruch Siach
Ray Jui
David Box
Neelesh Gupta
Beniamino Galvani
James Hogan
Laurentiu Palcu
Wei Yan
Anders Berg
Wolfram Sang