Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Later sanity checks on node properties (which would likely be missing)
should prevent this from causing much trouble however, especially as the
original premature free of the parent node has already been fixed
separately (but that "fix" was apparently never backported to stable).
Fixes: e7ec014a47 ("Input: twl6040-vibra - update for device tree support")
Fixes: c52c545ead ("Input: twl6040-vibra - fix DT node memory management")
Cc: stable <stable@vger.kernel.org> # 3.6
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> (on Pyra OMAP5 hardware)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A helper purported to look up a child node based on its name was using
the wrong of-helper and ended up prematurely freeing the parent of-node
while searching the whole device tree depth-first starting at the parent
node.
Fixes: 64b9e4d803 ("input: twl4030-vibra: Support for DT booted kernel")
Fixes: e661d0a044 ("Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning")
Cc: stable <stable@vger.kernel.org> # 3.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Just a few driver fixups, nothing exciting"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xen-kbdfront - do not advertise multi-touch pressure support
Input: hideep - fix compile error due to missing include file
Input: elants_i2c - do not clobber interrupt trigger on x86
Input: joystick/analog - riscv has get_cycles()
Input: elantech - add new icbody type 15
Input: ims-pcu - fix typo in the error message
Some user-space applications expect multi-touch pressure
on contact to be reported if it is advertised in device
properties. Otherwise, such applications may treat reports
not as actual touches, but hovering. Currently this is
only advertised, but not reported.
Fix this by not advertising that ABS_MT_PRESSURE is supported.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Andrii Chepurnyi <andrii_chepurnyi@epam.com>
Patchwork-Id: 10140017
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver was merged in 2011 as a tool for detecting the orientation
of a screen. The device driver assumes board file setup using the
platform data from <linux/input/gpio_tilt.h>. But no boards in the
kernel tree defines this platform data.
As I am faced with refactoring drivers to use GPIO descriptors and
pass decriptor tables from boards, or use the device tree device
drivers like these creates a serious problem: I cannot fix them and
cannot test them, not even compile-test them with a system actually
using it (no in-tree boardfile).
I suggest to delete this driver and rewrite it using device tree if
it is still in use on actively maintained systems.
I can also offer to rewrite it out of the blue using device tree if
someone promise to test it and help me iterate it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Patchwork-Id: 10133609
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
struct timeval which is part of struct input_event to maintain the event
times is not y2038 safe.
Real time timestamps are also not ideal for input_event as this time can go
backwards as noted in the patch a80b83b7b8 by John Stultz.
The patch switches the timestamps to use monotonic time from realtime time.
This is assuming no one is using absolute times from these timestamps.
The structure to maintain input events will be changed in a different
patch.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Patchwork-Id: 10118255
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
1. change "to" to "too".
2. move ")" to the front of "\n", which discovered by Joe Perches.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- three new touchscreen drivers: EETI EXC3000, HiDeep, and Samsung
S6SY761
- the timer API conversion (setup_timer() -> timer_setup())
- a few drivers swiytched to using managed API for creating custom
device attributes
- other assorted fixed and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (50 commits)
Input: gamecon - mark expected switch fall-throughs
Input: sidewinder - mark expected switch fall-throughs
Input: spaceball - mark expected switch fall-throughs
Input: uinput - unlock on allocation failure in ioctl
Input: add support for the Samsung S6SY761 touchscreen
Input: add support for HiDeep touchscreen
Input: st1232 - remove obsolete platform device support
Input: convert autorepeat timer to use timer_setup()
media: ttpci: remove autorepeat handling and use timer_setup
Input: cyttsp4 - avoid overflows when calculating memory sizes
Input: mxs-lradc - remove redundant assignment to pointer input
Input: add I2C attached EETI EXC3000 multi touch driver
Input: goodix - support gt1151 touchpanel
Input: ps2-gpio - actually abort probe when connected to sleeping GPIOs
Input: hil_mlc - convert to using timer_setup()
Input: hp_sdc - convert to using timer_setup()
Input: touchsceen - convert timers to use timer_setup()
Input: keyboard - convert timers to use timer_setup()
Input: uinput - fold header into the driver proper
Input: uinput - remove uinput_allocate_device()
...
We have to unlock before returning if input_allocate_device() fails.
Fixes: 04ce40a61a ("Input: uinput - remove uinput_allocate_device()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ/30WAAoJEHm+PkMAQRiG1YkIAIVgcZS9SPzjcH+/NpcNJ4wv
Bp8xyfj/X6Eswn63ebrV/qij65Esmha7wnSREcFqrfNecRwOAdvYCjj20jqKGws2
p03sOS4aVSpJSQcqJ9sdF3Xx/P7CcK4IAjr0ihQbqozXiZAgVzTlYJwB+ErBMWFU
6NFYXg/Xp7FJXJ0o14yHpZ4RqgbLV95CgFIG9hzwvCibsW6ZBvGtYBD99IjeojPg
rw+B+Osck7XjC6IHqF/u760nTOaP8vVlTrCRqvFityGS9ZFQZDzEKYqxYgk8cVFC
jzR3fuHiWiomhyP9dLUZn6UuYQTaThhY58LvsEwV0JVJH9mUwcA4u5nO0wDUCO4=
=hhQa
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rc8' into next
Merge with mainline to bring in SPDX markings to avoid annoying merge
problems when some header files get deleted.
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is nothing in the uinput kernel header that is of use to anyone in
the kernel besides the uinput driver itself, so let's fold it into the
driver code (leaving uapi part intact).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no need for this wrapper; let's use input_allocate_device()
directly, and complete initialization in uinput_create_device().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously uinput force feedback requests waited for the userspace
indefinitely, which caused users to block when uinput server process
become unresponsive. Let's establish a 30 seconds deadline for servicing
upload and erase force feedback effect actions, so that users have a
chance to abort stuck requests.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ7clWAAoJEHm+PkMAQRiG07AH/iKcej+AsurISHx6i/LUEDC1
a9wo5HAR5kEj+ohdE3JSkD9BHLcyhcCXaqIk9yOrwi9xv1DrPv8U/nGkKzZJzFi2
mGWK09Zgi+vgSpA+YSErgl05IVGtgaryQQPqQdawpyRpqTUwP0+2pLnKEnJe0f05
fpv+S4bDKUCuE8GcVNjF9gxXDg8j60fFa+oAcn7QPS6dCun/H6TbDRue5oeky0Y+
50ZYjjioy9S9DIm2VF7pktMCP/mK/fgb+Q+4Up09VJGHGhq+891SRJ27yDulxo47
/gq22SRIGBX2PGNllSwhYslgaCRRlYTMBYOIWrBreanA4NpGD662dp+GgWhD154=
=TAMw
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rc6' into next
Merge with mainline to bring in the timer API changes.
Pull input fixes from Dmitry Torokhov:
- joydev now implements a blacklist to avoid creating joystick nodes
for accelerometers found in composite devices such as PlaStation
controllers
- assorted driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ims-psu - check if CDC union descriptor is sane
Input: joydev - blacklist ds3/ds4/udraw motion sensors
Input: allow matching device IDs on property bits
Input: factor out and export input_device_id matching code
Input: goodix - poll the 'buffer status' bit before reading data
Input: axp20x-pek - fix module not auto-loading for axp221 pek
Input: tca8418 - enable interrupt after it has been requested
Input: stmfts - fix setting ABS_MT_POSITION_* maximum size
Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen
Input: synaptics - disable kernel tracking on SMBus devices
Before trying to use CDC union descriptor, try to validate whether that it
is sane by checking that intf->altsetting->extra is big enough and that
descriptor bLength is not too big and not too small.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that we have a platform_device_id table and multiple supported ids
we should be using MODULE_DEVICE_TABLE instead of MODULE_ALIAS.
This fixes a regression on Bay and Cherry Trail devices, where the power
button is now enumerated as an "axp221-pek" and it was impossible to
wakeup these devices from suspend since the module did not load.
Fixes: c3cc94470b ("Input: axp20x-pek - add support for AXP221 PEK")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- fixes for two long standing issues (lock up and a crash) in force
feedback handling in uinput driver
- tweak to firmware update timing in Elan I2C touchpad driver.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - extend Flash-Write delay
Input: uinput - avoid crash when sending FF request to device going away
Input: uinput - avoid FF flush when destroying device
-----BEGIN PGP SIGNATURE-----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=j+Q1
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-input-rtc-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into next
Merge "Immutable branch between MFD, Input and RTC due for the v3.14
merge window" to have dm355evm_msp.h header moved into right place.
-----BEGIN PGP SIGNATURE-----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=nb+l
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-many-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into next
Merge "Immutable branch between MFD and many other subsystems due for
the v4.14 merge window" to get the TWL headers moved to the right place.
Normally, when input device supporting force feedback effects is being
destroyed, we try to "flush" currently playing effects, so that the
physical device does not continue vibrating (or executing other effects).
Unfortunately this does not work well for uinput as flushing of the effects
deadlocks with the destroy action:
- if device is being destroyed because the file descriptor is being closed,
then there is noone to even service FF requests;
- if device is being destroyed because userspace sent UI_DEV_DESTROY,
while theoretically it could be possible to service FF requests,
userspace is unlikely to do so (they'd need to make sure FF handling
happens on a separate thread) even if kernel solves the issue with FF
ioctls deadlocking with UI_DEV_DESTROY ioctl on udev->mutex.
To avoid lockups like the one below, let's install a custom input device
flush handler, and avoid trying to flush force feedback effects when we
destroying the device, and instead rely on uinput to shut off the device
properly.
NMI watchdog: Watchdog detected hard LOCKUP on cpu 3
...
<<EOE>> [<ffffffff817a0307>] _raw_spin_lock_irqsave+0x37/0x40
[<ffffffff810e633d>] complete+0x1d/0x50
[<ffffffffa00ba08c>] uinput_request_done+0x3c/0x40 [uinput]
[<ffffffffa00ba587>] uinput_request_submit.part.7+0x47/0xb0 [uinput]
[<ffffffffa00bb62b>] uinput_dev_erase_effect+0x5b/0x76 [uinput]
[<ffffffff815d91ad>] erase_effect+0xad/0xf0
[<ffffffff815d929d>] flush_effects+0x4d/0x90
[<ffffffff815d4cc0>] input_flush_device+0x40/0x60
[<ffffffff815daf1c>] evdev_cleanup+0xac/0xc0
[<ffffffff815daf5b>] evdev_disconnect+0x2b/0x60
[<ffffffff815d74ac>] __input_unregister_device+0xac/0x150
[<ffffffff815d75f7>] input_unregister_device+0x47/0x70
[<ffffffffa00bac45>] uinput_destroy_device+0xb5/0xc0 [uinput]
[<ffffffffa00bb2de>] uinput_ioctl_handler.isra.9+0x65e/0x740 [uinput]
[<ffffffff811231ab>] ? do_futex+0x12b/0xad0
[<ffffffffa00bb3f8>] uinput_ioctl+0x18/0x20 [uinput]
[<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
[<ffffffff81337553>] ? security_file_ioctl+0x43/0x60
[<ffffffff812414a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71
Reported-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Reported-by: Clément VUCHENER <clement.vuchener@gmail.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=193741
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
FIFO_MODE() is a macro expression with a '<<' operator, which gcc points
out could be misread as a '<':
drivers/input/misc/adxl34x.c: In function 'adxl34x_probe':
drivers/input/misc/adxl34x.c:799:36: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
While utility of this warning is being disputed (Chief Penguin: "This
warning is clearly pure garbage.") FIFO_MODE() extracts range of values,
with 0 being FIFO_BYPASS, and not something that is logically boolean.
This converts the test to an explicit comparison with FIFO_BYPASS,
making it clearer to gcc and the reader what is intended.
Fixes: e27c729219 ("Input: add driver for ADXL345/346 Digital Accelerometers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
"A second round of updates for the input subsystem:
- a new driver for PWM-controlled vibrators
- ucb1400 touchscreen driver had completely busted suspend/resume
handling
- we now handle "home" button found on some devices with Goodix
touchscreens
- assorted other fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Gigabyte P57 to the keyboard reset table
Input: xpad - validate USB endpoint type during probe
Input: ucb1400_ts - fix suspend and resume handling
Input: edt-ft5x06 - fix access to non-existing register
Input: elantech - make arrays debounce_packet static, reduces object code size
Input: surface3_spi - make const array header static, reduces object code size
Input: goodix - add support for capacitive home button
Input: add a driver for PWM controllable vibrators
Input: adi - make array seq static, reduces object code size
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
Provide a simple driver for PWM controllable vibrators.
It will be used by Motorola Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Long pressed key could not show right in XEN vncviewer after tigervnc
client changed the way how to send repeat keys, from "Down Up Down Up
..." to "Down Down ... Up". This will report autorepeat to input by
checking if same key being pressed, and let handler process it finally.
Signed-off-by: Liang Yan <lyan@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Dell XPS13 9365 has an INT33D2 ACPI node with no GPIOs, causing
the following error in dmesg:
[ 7.172275] soc_button_array: probe of INT33D2:00 failed with error -2
This commit silences this, by returning -ENODEV when there are no GPIOs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196679
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The AXP221 has different values for startup time bits from the AXP20X.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To prepare an upcoming patch adding support for another PMIC that has
different startup and shutdown time, use driver_data of
platform_device_id instead of a fixed extended device attribute.
By doing so, we also remove a lot of nested structures that aren't
useful.
With this patch, a new PMIC can be easily supported by just filling
correctly its ax20x_info structure and adding a platform_device_id.
Moreover, since we get rid of extended attributes, rename
axp20x_store_ext_attr to axp20x_store_attr and axp20x_show_ext_attr to
axp20x_show_attr.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes the following issues in pcspkr:
* Return -EINVAL when input arguments are not valid in pcspkr_event
function instead of -1.
* Replace <asm/io.h> with <linux/io.h>
* Fix indentation of case blocks in switch statement
* Reduce length of line 28 to less than 80 characters
The style issues were discovered by checkpatch.pl script.
Signed-off-by: Munir Contractor <munircontractor@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver provides a input driver for the power key on the Rockchip RK805
PMIC.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that we have proper managed API to create device attributes, let's
use it instead of installing a custom devm action.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6039 944 0 6983 1b47 drivers/input/misc/yealink.o
File size After adding 'const':
text data bss dec hex filename
6103 880 0 6983 1b47 drivers/input/misc/yealink.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Henk Vergonet <henk.vergonet@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
13547 1600 0 15147 3b2b drivers/input/misc/ims-pcu.o
File size After adding 'const':
text data bss dec hex filename
13675 1472 0 15147 3b2b drivers/input/misc/ims-pcu.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Extend xen_kbdfront to provide multi-touch support to unprivileged domains.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
[dtor: factor out various sub-protocols - multitouch, single touch, keys]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are passing a buffer with ACPI_ALLOCATE_BUFFER set to
acpi_evaluate_object, so we must free it when we are done with it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Xen input para-virtual protocol defines string constants
used by both back and frontend. Use those instead of
explicit strings in the frontend driver.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least on devices with the AXP288 PMIC the device is expected to
wakeup from suspend when the power-button gets pressed, add support
for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
acpi_dev_found checks that there is a matching ACPI node, but it
may be disabled (_STA method returns 0) in which case the
soc_button_array driver will not bind to it and axp20x-pek should
handle the power-button.
This commit switches from acpi_dev_found to acpi_dev_present to
avoid not registering an input-dev for the powerbutton when there
is a disabled PNP0C40 device.
The ACPI-6.0 standard defines a standard gpio button device using
the ACPI0011 HID replacing the custom PNP0C40 gpio device, many
newer devices define both PNP0C40 and ACPI0011 devices enabling one
or the other depending on whether the BIOS thinks it is going to boot
Android or Windows.
This commit adds a check for the ACPI0011 device, so that if
either device is present *and* enabled we don't register an input-dev
for the powerbutton.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 9b13a4ca8d ("Input: axp20x-pek - do not register input device
on some systems") added a check for the INTCFD9 ACPI device which also
handles the powerbutton as on some systems the powerbutton is connected
to both the PMIC, handled by axp20x-pek, and to a gpio on the SoC, handled
by soc_button_array which attaches itself to the INTCFD9 ACPI device.
Testing + comparing DSDTs has shown that this only happens on Cherry
Trail devices with an AXP288 PMIC, the AXP288 PMIC is also used on
Bay Trail devices but there the power button is only connected to
the PMIC and not handled by soc_button_array.
This means that the INTCFD9 check has caused a regression on Bay Trail
devices, causing power-button presses to no longer be seen.
This commit fixes this by limiting the check to devices where the ACPI
node for the AXP288 contains a _HRV (hardware revision) attribute with
a value of 3 which indicates we are dealing with a Cherry Trail platform.
Fixes: 9b13a4ca8d ("Input: axp20x-pek - do not register input ...")
Reported-by: Сергей Трусов <t.rus76@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Core changes
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources.
I have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements
- A whole slew of drivers have their spinlocks chaned to raw spinlocks
as they provide irqchips, and thus we are progressing on realtime
compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZCusBAAoJEEEQszewGV1zengP/i3YgmSXJdaf26t/NxG3klU3
qx3akdQ3gEQ6BOlIY7Ew+b6qgMJynYNZa1trZgqTgLxPEKWjidyCgz+LHQ0OY+ir
a7x6wr+gBj5WlgV+nBjVs4l6W8pVKCfnap/04OPEQDpxZOHs2LU5pqxxUZ9AxkKS
urDFMDX55baFviQ+xAuHgamok87YoGP36A/e/fHIBepZmnochf0mCcPfIh0t8lRh
s2x29PN5ZFRkl403RzjZfVCEMr9bMnSqmDquvPO++Kq0bL+3rOhuMErocd1Bg8ao
LxBktkryujTaw699xK7Rq5SwcnOAPpaBY4NTmwsIJvAJuCh7qLy9JxQSBsSOT2bx
61NWUt5T/Xsi0ECYZM4YvsNpUP6XrpSTyG3c8T3fY9vXYLNKZBv1ht6OODpLeuke
DxULAWP+DdzUS8a3qfKQvIJzSTloU31a1MBG58DWNJ072EQfa2YNaVE75VQk/z5/
0xZbSHdPY/0Xgx8ltpKu37bSO676JiVQZZ1HEAuti4h21+USYueYD2L8/Bx4k9e/
4UaOcw3MaCDHP/sf5hg17kQBjhhS0lV9Zv6H9QbHZUocJTJlIU+vXtgkQlrfi3n8
8j5m+ywVarmLtPqg1j2rqcw7LBCPe0qRXH3e5X/YmNMc3rH9bQz4cTo8ZSN9r8zS
c17zGbbAqlGsBkpFAbQz
=DGPb
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.12 kernel cycle.
Core changes:
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources. I
have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers:
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements:
- A whole slew of drivers have their spinlocks chaned to raw
spinlocks as they provide irqchips, and thus we are progressing on
realtime compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot"
* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: f7188x: Add a missing break
gpio: omap: return error if requested debounce time is not possible
gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
gpio: gpio-wcove: fix GPIO IRQ status mask
gpio: DT bindings, move tca9554 from pcf857x to pca953x
gpio: move tca9554 from pcf857x to pca953x
gpio: arizona: Correct check whether the pin is an input
gpio: Add XRA1403 DTS binding documentation
dt-bindings: add exar to vendor prefixes list
gpio: gpio-wcove: fix irq pending status bit width
gpio: dwapb: use dwapb_read instead of readl_relaxed
gpio: aspeed: Add open-source and open-drain support
gpio: aspeed: Add debounce support
gpio: aspeed: dt: Add optional clocks property
gpio: aspeed: dt: Fix description alignment in bindings document
gpio: mvebu: Add limited PWM support
gpio: Use unsigned int for interrupt numbers
gpio: f7188x: Add F71889A GPIO support.
gpio: core: Decouple open drain/source flag with active low/high
gpio: arizona: Correct handling for reading input GPIOs
...
Pull input subsystem updates from Dmitry Torokhov:
- a big update from Mauro converting input documentation to ReST format
- Synaptics PS/2 is now aware of SMBus companion devices, which means
that we can now use native RMI4 protocol to handle touchpads, instead
of relying on legacy PS/2 mode.
- we removed support from BMA180 accelerometer from input devices as it
is now handled properly by IIO
- update to TSC2007 to corretcly report pressure
- other miscellaneous driver fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (152 commits)
Input: ar1021_i2c - use BIT to check for a bit
Input: twl4030-pwrbutton - use input_set_capability() helper
Input: twl4030-pwrbutton - use correct device for irq request
Input: ar1021_i2c - enable touch mode during open
Input: add uinput documentation
dt-bindings: input: add bindings document for ar1021_i2c driver
dt-bindings: input: rotary-encoder: fix typo
Input: xen-kbdfront - add module parameter for setting resolution
ARM: pxa/raumfeld: fix compile error in rotary controller resources
Input: xpad - do not suggest writing to Dominic
Input: xpad - don't use literal blocks inside footnotes
Input: xpad - note that usb/devices is now at /sys/kernel/debug/
Input: docs - freshen up introduction
Input: docs - split input docs into kernel- and user-facing
Input: docs - note that MT-A protocol is obsolete
Input: docs - update joystick documentation a bit
Input: docs - remove disclaimer/GPL notice
Input: fix "Game console" heading level in joystick documentation
Input: rotary-encoder - remove references to platform data from docs
Input: move documentation for Amiga CD32
...
Cleanup driver slightly by using input_set_capability() instead
of manually setting the required bits.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The interrupt should be requested for the platform device
and not for the input device.
Fixes: 7f9ce649d2 ("Input: twl4030-pwrbutton - simplify driver using devm_*")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a parameter for setting the resolution of xen-kbdfront in order to
be able to cope with a (virtual) frame buffer of arbitrary resolution.
While at it remove the pointless second reading of parameters from
Xenstore in the device connection phase: all parameters are available
during device probing already and that is where they should be read.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Motorola CPCAP is a PMIC found in multiple smartphones.
This driver adds support for the power/on button and has
been tested in Droid 4.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
sparse says
warning: incorrect type in assignment (different base types)
expected unsigned short [unsigned] [usertype] offset
got restricted __be16 [usertype] <noident>
for every usage of cpu_to_be16 in yealink.c. Defining it __be16 in the
first place shouldn't hurt.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Henk.Vergonet@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When submitting the support for the ACPI0011 windows tablet keys device I
mapped the "windows" logo homekey to KEY_HOMEPAGE. But this is inconsistent
with how it is done on windows tablets using the old PNP0C40 ACPI device
and it does not match the HUT spec, which says that usage-page 7 usage 0xe3
is "Keyboard Left GUI".
This commit maps usage-page 7 usage 0xe3 to KEY_LEFTMETA fixing this.
Fixes: 4c3362f449 ("Input: soc_button_array - add support for ACPI 6.0...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add pm8xxx_regs for this PMIC and the device tree match table entry.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some PMIC vibrator IPs use a separate enable register to turn the
vibrator on and off. To detect if a vibrator uses this feature, rely on
the enable_mask being non-zero.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to prepare this driver to support other vibrators of the same
kind, move some hardcoded values to a structure holding register
parameters (address, mask, shit of the control register).
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY4ZYkAAoJEHm+PkMAQRiGsq4H/R4PMXDoe2XhSSk7IoT97pXV
/A8np/scAPjzEgYUidbb54OSqWwsPRuPGWONTFeSrE2u0L4wln/REI91jg7QetLq
IisncExlYeJ/XQ+iO0ZZh9fLbqwIlEJFdSXmyIFr3m/TBxe8a61C8j93oNgM1tHT
yuwzlq7c3sLq2hsmUG2HyL2kJsEfRasv4Rk0yhFuti12zVsBoTW4qmZuMauq+gdf
f7cSYgiHhPTdb2o+azg5O7uYNHaQQBxdUMlIuhhYtVOUq+pFDO23SLHSFIW2NwOm
Zn5R6CFSrLsCw0Bx0v8Xlc151QUbaRK4h9lhUhkBr6d3uNShU1NQ9JojpSvYwBo=
=vP6E
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rc5' into next
Sync up with mainline to bring in changes to input subsystem merged
through other trees.
This essentially reverts commit baf28d91e7 ("Input: bma150 - avoid
binding to bma180 if IIO bma180 driver present") and commit ef3714fdbc
("Input: bma150 - extend chip detection for bma180")
Rationale: initially (2012) the GTA04 device using a bma180 chip simply
referenced the bma150 platform driver in its board file [1] which happened
to work in all scenarios that were tested.
When conversion to DT started (2014), we needed to make the driver be still
recognised. Hence we introduced the compatibility to the bma180 chip in
Linux 3.15-rc5 [2] without further checks if it is really 100% compatible.
This worked flawlessly for years with the GTA04 device.
Recently (2016), Hans de Goede pointed out that the chips are not as
similar as they appeared and the driver works with the bma180 for the GTA04
only by good luck. He proposed to remove the bma180 support completely [3],
but we still did need it until we have a replacement. Thus, a conditional
compile was added.
We have now developed a generic iio-input-bridge which works with any 2 or
3 axis iio based accelerometer. It has been tested on GTA04 and Pyra and
works as expected. Therefore we can remove the bma180 support from this
driver completely. User-space API compatibility can be restored by using
the iio-input-bridge.
Maybe it is time to convert the bma150 driver to iio as well and retire the
accelerometer input drivers completely but this is a different story and
task.
[1]: https://github.com/neilbrown/linux/blob/gta04/3.2.y/arch/arm/mach-omap2/board-omap3gta04.c#L976
[2]: https://patchwork.kernel.org/patch/3961171/
[3]: https://patchwork.kernel.org/patch/9325481/
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To enable eventual removal of pr_warning
This makes pr_warn use consistent for drivers/input
Prior to this patch, there were 8 uses of pr_warning and
17 uses of pr_warn in drivers/input
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Windows 10 tablets with gpio buttons will typically use the ACPI 6.0
Generic Button Device with a HID of ACPI0011 for these buttons.
The ACPI description for these in the ACPI0011 devices _DSD object uses
something resembling HID descriptors, except that instead of indicating
a bit index into a HID input report, the index indicates the _CRS index
for the GPIO.
The use of 1 interrupt per button, some of which need to be wakeup
sources, instead of using input reports makes it impossible to use the
HID subsystem for this.
This really is just another gpio-keys input device with the platform
data described in ACPI, so this commit adds parsing for this new way
to describe gpio-keys to the soc_button_array driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Count how much gpio_keys we actually need, this is a preparation patch
for adding support for the new Win10 / ACPI-6.0 "Generic Buttons Device"
support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: aca951a22a ("[PATCH] input-driver-yealink-P1K-usb-phone")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.14
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack control-interface endpoints.
Fixes: 628329d524 ("Input: add IMS Passenger Control Unit driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c04148f915 ("Input: add driver for USB VoIP phones with CM109...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.28
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since gpiod_count() does not return 0 anymore, we don't need to shadow
its error code and would safely propagate to the user.
While here, replace second parameter by NULL in order to prevent side
effects on _DSD enabled firmware.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpiolib-acpi code is becoming more strict and connection-IDs
may only be used with devices which have a _DSD with matching IDs
in there. Since the soc_button_array ACPI binding is pure index
based pass in NULL as connection-ID to avoid the more strict cheks
resulting in gpiod_count and gpiod_get_index not returning any gpios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some systems (Intel tablets with axp288 pmic) the powerbutton is
also connected to a gpio pin of the SoC, advertised through the
"INTCFD9" / "PNP0C40" acpi device. This leads to double reporting
of powerbutton events, which is undesirable, so one driver needs
to not report input events in this case.
Since the soc_button_array driver for the "PNP0C40" acpi device
also handles wake from suspend on these tablets and since the
axp20x-pel driver requires relative expensive i2c accrsses,
it is best for the axp20x-pek driver to not register an input device
in this case.
Note that this commit leaves the axp20x-driver bound to the
device, rather then returning -ENODEV, this is done so that the
sysfs attributes it offers are kept around.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move all input device related initialization into a new
axp20x_pek_probe_input_device helper function.
This introduces one functional change, the input device is now
registered before the sysfs attr get registered. This is not a problem
as the sysfs attr are to configure some long press settings (forced
poweroff) in the hardware and do not interact with the input_device.
This is a preparation patch for not always registering the input dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before this commit axp20x-pek was mixing 2 style error reporting calls:
dev_err(&pdev->dev, ...);
dev_err(axp20x->dev, ...);
But the second is our parent device, not our own device, so switch to
using &pdev->dev everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the driver is using generic device properties, it should work
properly when CONFIG_OF is turned off. This patch removes the
ifdef CONFIGOF and make sure the driver always have of_match_table.
Signed-off-by: Jingkui Wang <jkwang@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Extend the pwm-beeper driver to support customized frequency for SND_BELL
from device properties.
Signed-off-by: Guan Ben <ben.guan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If user tries to initialize uinput device mixing old and new style
initialization (i.e. using old UI_SET_ABSBIT instead of UI_ABS_SETUP,
we forget to allocate input->absinfo and will crash when trying to send
absolute events:
ioctl(ui, UI_DEV_SETUP, &us);
ioctl(ui, UI_SET_PHYS, "Test");
ioctl(ui, UI_SET_EVBIT, EV_ABS);
ioctl(ui, UI_SET_ABSBIT, ABS_X);
ioctl(ui, UI_SET_ABSBIT, ABS_Y);
ioctl(ui, UI_DEV_CREATE, 0);
Reported-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=191811
Fixes: fbae10db09 ("Input: uinput - rework ABS validation")
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MPU3050 driver in the input subsystem has been superseded by a proper
IIO driver found in drivers/iio/gyro/mpu3050*.
Patches have been submitted to remove all defconfig and related references
to the old driver and replace this input driver with the IIO driver.
So delete the input driver. Input was never a good fit for sensors anyway.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYhRv9AAoJEHm+PkMAQRiG/uAH+wYT9qwvT460pUC6F1X5PNdN
H5KvaGsRNP1SjjQid5CrAFFDs52pFKf9GoV0Rn2WRoHAmEF1Dps4y/bMtR1GlsRB
IfOU+bnmH1Mmj4RCXUoFgFgYJVXC0WOz9SM5aCOAAZLCRF9BdkTpRo8lijuh141k
7YMqpaRhr/rJvQRZMEX+Q8HhfyNHz53olrykYp+O4x5F/CUihFzH76pY28j0YihS
wd/DdxrWyFn35DcFGfDb3yK7J2a6pGtnFw3RP4gU8DsH/Ks0133cR/2lOAtGDECN
dAGbLHoTvj3L4Twz5aiH6WRkXUkfDLK9UhxD/82UgLLmP5XvG1RdKZUNQ60CL5g=
=2TBu
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rc5' into next
Sync up with mainline to bring up improvements in various subsystems.
Since there is no call to dev_get_drvdata() or input_get_drvdata(),
the call to input_set_drvdata() is unnecessary and can be dropped.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The "atomic" API allows us to configure PWM period and duty cycle and
enable it in one call.
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds an optional regulator to the pwm-beeper device. This regulator
acts as an amplifier. The amplifier is only enabled while beeping in order
to reduce power consumption.
Tested on LEGO MINDSTORMS EV3, which has a speaker connected to PWM through
an amplifier.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This suppress printing an error message when pwm_get returns -EPROBE_DEFER.
Otherwise you get a bunch of noise in the kernel log.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Usually userspace sends SND_BELL and SND_TONE events, and by the time
pwm_beeper_suspend() runs userpsace is already frozen, but theoretically
in-kernel users may send these events too, and that may cause
pwm_beeper_event() scheduling another work after we canceled it.
Let's introduce a "suspended" flag and check it in pwm_beeper_event() to
avoid this race.
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use of managed resources (devm) simplifies error handling and tear down
of the driver.
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are no more users of pwm-beeper driver in mainline relying on
this legacy API, so let's remove it and simplify the driver code.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Empty remove functions don't serve a useful purpose and can be removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calling device_init_wakeup in the remove function is unnecessary since the
device is going away, and thus won't be able to cause any wakeups under any
circumstances. Besides, the driver cleanup code already handles the
necessary cleanup.
Similarly, disabling wakeup in the probe error path is unnecessary, as is
disabling wakeup in the probe function in the first place.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a function declares a variable to access a structure element,
use it consistently.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to i2c_get_clientdata(), platform_get_drvdata(),
or dev_get_drvdata() in any of the drivers in this patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The soc_button_array driver was initializing (kzalloc) the
debounce_interval value to 0, leading to no debouncing at all,
while the buttons are simple mechanical switches.
This commit sets debounce_interval to 50ms to avoid spurious button
press reports both on press and release of the button. Note 50ms may
seem like a lot but soc_button_array is typically used with cheap
tablets, with not so great buttons. I tried 10ms on my tablet and it
is not enough, where as 50ms works well.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to platform_set_drvdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to platform_set_drvdata().
Also use existing variable 'dev' instead of dereferencing it several times.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use local variable 'dev' instead of dereferencing it several times.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to i2c_get_clientdata() or dev_get_drvdata().
Drop the unnecessary call to i2c_set_clientdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to platform_set_drvdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use local variable 'dev' instead of dereferencing it several times and
replace devm_add_action() and manual error handling with
devm_add_action_or_reset().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Small driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - avoid divide by 0 errors on bad touchscreen data
Input: adxl34x - make it enumerable in ACPI environment
Input: ALPS - fix TrackStick Y axis handling for SS5 hardware
Input: synaptics-rmi4 - fix F03 build error when serio is module
Input: xpad - use correct product id for x360w controllers
Input: synaptics_i2c - change msleep to usleep_range for small msecs
Input: i8042 - add Pegatron touchpad to noloop table
Input: joydev - remove unused linux/miscdevice.h include
The ACPI-enabled platform may contain _DSD method to enable this driver
using compatible string.
Remove OF specifics to re-use existing code on ACPI-enabled platforms.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
msleep (1~20) may not do what the caller intends, and will often sleep
longer. (~20 ms actual sleep for any value given in the 1~20ms range) This
is not the desired behaviour for many cases like device resume time, device
suspend time, device enable time, etc. Thus, change msleep to usleep_range
for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Acked by: Albert Zhang <xu.zhang@bosch-sensortec.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull input subsystem updates from Dmitry Torokhov:
- updated support for Synaptics RMI4 devices, including support for
SMBus controllers, firmware update support, sensor tuning, and PS/2
guest support
- ALPS driver now supports tracksticks on SS5 controllers
- i8042 now uses chassis info to skip selftest on Asus laptops as list
of individual models became too unwieldy
- miscellaneous fixes to other drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (67 commits)
Input: imx6ul_tsc - generalize the averaging property
Input: drv260x - use generic device properties
Input: drv260x - use temporary for &client->dev
Input: drv260x - fix input device's parent assignment
Input: synaptics-rmi4 - add support for F34 V7 bootloader
Input: drv260x - fix initializing overdrive voltage
Input: ALPS - fix protcol -> protocol
Input: i8042 - comment #else/#endif of CONFIG_PNP
Input: lpc32xx-keys - fix invalid error handling of a requested irq
Input: synaptics-rmi4 - fix debug for sensor clip
Input: synaptics-rmi4 - store the attn data in the driver
Input: synaptics-rmi4 - allow to add attention data
Input: synaptics-rmi4 - f03 - grab data passed by transport device
Input: synaptics-rmi4 - add support for F03
Input: imx6ul_tsc - convert int to u32
Input: imx6ul_tsc - add mask when set REG_ADC_CFG
Input: synaptics-rmi4 - have only one struct platform data
Input: synaptics-rmi4 - remove EXPORT_SYMBOL_GPL for internal functions
Input: synaptics-rmi4 - remove mutex calls while updating the firmware
Input: drv2667 - fix misuse of regmap_update_bits
...
No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- Support for stereo DAPM controls
- Some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- A new version of the topology ABI; this should be backward compatible
- Updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- New drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- Yet another race fix at disconnection
- Tolerated packet size calculation for some Android devices
- Quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- Improvement of Dell pin fixup mapping
- Quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- Replace all kthread usages with simple works
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=WZeb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- support for stereo DAPM controls
- some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- a new version of the topology ABI; this should be backward
compatible
- updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- new drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- yet another race fix at disconnection
- tolerated packet size calculation for some Android devices
- quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- improvement of Dell pin fixup mapping
- quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- replace all kthread usages with simple works"
* tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (296 commits)
ALSA: hiface: Fix M2Tech hiFace driver sampling rate change
ALSA: usb-audio: Eliminate noise at the start of DSD playback.
ALSA: usb-audio: Add native DSD support for TEAC 501/503 DAC
ASoC: wm_adsp: wm_adsp_buf_alloc should use kfree in error path
ASoC: topology: avoid uninitialized kcontrol_type
ALSA: usb-audio: Add QuickCam Communicate Deluxe/S7500 to volume_control_quirks
ALSA: usb-audio: add implicit fb quirk for Axe-Fx II
ASoC: zte: spdif: correct ZX_SPDIF_CLK_RAT define
ASoC: zte: spdif and i2s drivers are not zx296702 specific
ASoC: rsnd: setup BRGCKR/BRRA/BRRB when starting
ASoC: rsnd: enable/disable ADG when suspend/resume timing
ASoC: rsnd: tidyup ssi->usrcnt counter check in hw_params
ALSA: cs46xx: add a new line
ASoC: Intel: update bxt_da7219_max98357a to support quad ch dmic capture
ASoC: nau8825: disable sinc filter for high THD of ADC
ALSA: usb-audio: more tolerant packetsize
ALSA: usb-audio: avoid setting of sample rate multiple times on bus
ASoC: cs35l34: Simplify the logic to set CS35L34_MCLK_CTL setting
ALSA: hda - Gate the mic jack on HP Z1 Gen3 AiO
ALSA: hda: when comparing pin configurations, ignore assoc in addition to seq
...
Update driver drv260x to use generic device properties so that it can be
used on non-DT systems. We also remove platform data as generic device
properties work on static board code as well.
Signed-off-by: Jingkui Wang <jkwang@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's introduce a temporary for "client->dev" is probe() as we use
it quite a few times and "dev" is shorter.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We were assigning I2C bus controller instead of client as parent device.
Besides being logically wrong, it messed up with devm handling of input
device. As a result we were leaving input device and event node behind
after rmmod-ing the driver, which lead to a kernel oops if one were to
access the event node later.
Let's remove the assignment and rely on devm_input_allocate_device() to
set it up properly for us.
Signed-off-by: Jingkui Wang <jkwang@google.com>
Fixes: 7132fe4f56 ("Input: drv260x - add TI drv260x haptics driver")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We were accidentally initializing haptics->rated_voltage twice, and did not
initialize overdrive voltage.
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The name of a codec pin can have an optional prefix string, which is
defined by the SoC machine driver. The snd_soc_dapm_x_pin functions
take the fully-specified name including the prefix and so the existing
code would fail to find the pin if the audio machine driver had added
a prefix.
Switch to using the snd_soc_component_x_pin equivalent functions that
take a specified SoC component and automatically add the name prefix to
the provided pin name.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).
In such a case, the correct use is regmap_update_bits(..., mask, mask).
This driver is performing such a mistake with the DRV2667_STANDBY mask,
which equals (1 << 6). Fix the driver to make it consistent with the
API, and fix the alignment problem at the same time. Please note that
this change is untested, as I do not have this piece of hardware.
Testers are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).
In such a case, the correct use is regmap_update_bits(..., mask, mask).
This driver is performing such a mistake with the DRV2665_STANDBY mask,
which equals BIT(6). Fix the driver to make it consistent with the API,
and fix the alignment problem at the same time. Please note that this
change is untested, as I do not have this piece of hardware. Testers
are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The PNP0C40 device of the Surface 3 doesn't have any GPIO attached to it.
Instead of trying to access the GPIO, request the count beforehand and
bail out if it is null or if an error is returned.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gpio_keys will later use gpio_is_valid(). To match the actual
behavior, we should use it here too.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit ef3714fdbc ("Input: bma150 - extend chip detection for bma180"),
adds bma180 chip-ids to the input bma150 driver, assuming that they are
100% compatible, but the bma180 is not compatible with the bma150 at all,
it has 14 bits resolution instead of 10, and it has quite different
control registers too.
Treating the bma180 as a bma150 wrt its data registers will just result
in throwing away the lowest 4 bits, which is not too bad. But the ctrl
registers are a different story. Things happen to just work but supporting
that certainly does not make treating the bma180 the same as the bma150
right.
Since some setups depend on the evdev interface the bma150 driver offers
on top of the bma180, we cannot simply remove the bma180 ids.
So this commit only removes the bma180 id when the bma180 iio driver,
which does treat the bma180 properly, is enabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
This requires to change the type of the reads from int to unsigned,
but these cases have been wrong before: negative values are not allowed
for the modified cases.
Cc: dmitry.torokhov@gmail.com
Cc: linux-input@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/input/misc/da9063_onkey.ko | grep alias
alias: platform:da9063-onkey
After this patch:
$ modinfo drivers/input/misc/da9063_onkey.ko | grep alias
alias: platform:da9063-onkey
alias: of:N*T*Cdlg,da9062-onkeyC*
alias: of:N*T*Cdlg,da9062-onkey
alias: of:N*T*Cdlg,da9063-onkeyC*
alias: of:N*T*Cdlg,da9063-onkey
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Copyright header is updated to add DA9061 in its description and the module
description macro is extended to include DA9061.
Minor change to the code, alters dev_dbg() statements to report a generic
"PMIC" instead of DA9063. This device driver is compatible with DA9061,
DA9062 and DA9063.
Kconfig is updated to reflect support for DA9061/62/63.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
platform_device_id table is needed for adding the tps65218-pwrbutton
module to the mfd_cell array.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into next
Sync up with mainline to bring in I2C host notify changes and other
updates.
Pull input subsystem updates from Dmitry Torokhov:
"You will get
- a new driver for Elan eKTF2127 touchscreen controllers
- a new "gpio-decoder" driver to read and report state of several
GPIO lines
- an ADC resistor ladder driver
- the ft6326 driver is removed because edt-ft5x06 handles the same
devices just fine.
.. plus the regular slew of driver fixes/enhancements"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (26 commits)
Input: elan_i2c - fix return tests of i2c_smbus_read_block_data()
Input: ektf2127 - mark PM functions as __maybe_unused
Input: snvs_pwrkey - drop input_free_device call if input_register_device fails
Input: add support for Elan eKTF2127 touchscreen controller
Input: serio - add hangup support
Input: tps65218-pwrbutton - add support for tps65217 variant
Input: jornada720_ts - get rid of mach/irqs.h and mach/hardware.h includes
Input: jornada720_kbd - remove unneeded mach/hardware.h include
Input: focaltech - mark focaltech_set_resolution() static
Input: wdt87xx_i2c - fix the flash erase issue
Input: gpio-keys-polled - don't use unit-address with button nodes
Input: add generic input driver to read encoded GPIO lines
Input: add ADC resistor ladder driver
Input: pegasus_notetaker - directly include workqueue header
Input: elants_i2c - get product id on recovery mode for FW update
Input: wm97xx - remove deprecated create_singletheread_workqueue
Input: mc13783_ts - remove deprecated create_singletheread_workqueue
Input: psmouse - remove deprecated create_singletheread_workqueue
Input: jornada720_kbd - switch to using dev_dbg
Input: jornada720_kbd - get rid of mach/irqs.h include
...
The power button found in tps65217 device is very similar to the tps65218,
so let's enhance the driver to support both variants.
This driver enables us to use tps65217's power button as KEY_POWER on
am335x boards (directly connected button in chiliboard, accessible pin
via expansion header in beaglebone). This patch has been tested with
chiliboard.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many modules call misc_register and misc_deregister in its module init
and exit methods without any additional code. This ends up being
boilerplate. This patch adds helper macro module_misc_device(), that
replaces module_init()/ module_exit() with template functions.
This patch also converts drivers to use new macro.
Change since v1:
Add device.h include in miscdevice.h as module_driver macro was not
available from other include files in some architectures.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a driver to read group of GPIO lines and provide its status as a
numerical value as input event to the system. This will help in
interfacing devices, that can be connected over GPIOs, that provide
input to the system by driving GPIO lines connected to them like a
rotary dial or a switch.
For example, a rotary switch can be connected to four GPIO lines. The
status of the GPIO lines reflect the actual position of the rotary
switch dial. For example, if dial points to 9, then the four GPIO lines
connected to the switch will read HLLH(0b'1001 = 9). This value
can be reported as an ABS_* event to the input subsystem.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
"Two new drivers for touchscreen controllers:
- Silead touchscreen controllers
- SiS 9200 family touchscreen controllers
and a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: silead - remove some dead code
Input: sis-i2c - select CONFIG_CRC_ITU_T
Input: add driver for SiS 9200 family I2C touchscreen controllers
Input: ili210x - fix permissions on "calibrate" attribute
Input: elan_i2c - properly wake up touchpad on ASUS laptops
Input: add driver for Silead touchscreens
Input: elantech - fix debug dump of the current packet
Input: rotary_encoder - support binary encoding of states
Input: xpad - power off wireless 360 controllers on suspend
Input: i8042 - break load dependency between atkbd/psmouse and i8042
Input: synaptics-rmi4 - do not check for NULL when calling of_node_put()
Input: cros_ec_keyb - cleanup use of dev
It's not advisable to use this encoding, but to support existing devices
add support for this to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. This contains the following new
drivers promised in the last merge window:
- driver for touchscreen controller found in Surface 3
- driver for Pegasus Notetaker tablet
- driver for Atmel Captouch Buttons
- driver for Raydium I2C touchscreen controllers
- powerkey driver for HISI 65xx SoC
plus a few fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: tty/vt/keyboard - use memdup_user()
Input: pegasus_notetaker - set device mode in reset_resume() if in use
Input: pegasus_notetaker - cancel workqueue's work in suspend()
Input: pegasus_notetaker - fix usb_autopm calls to be balanced
Input: pegasus_notetaker - handle usb control msg errors
Input: wacom_w8001 - handle errors from input_mt_init_slots()
Input: wacom_w8001 - resolution wasn't set for ABS_MT_POSITION_X/Y
Input: pixcir_ts - add support for axis inversion / swapping
Input: icn8318 - use of_touchscreen helpers for inverting / swapping axes
Input: edt-ft5x06 - add support for inverting / swapping axes
Input: of_touchscreen - add support for inverted / swapped axes
Input: synaptics-rmi4 - use the RMI_F11_REL_BYTES define in rmi_f11_rel_pos_report
Input: synaptics-rmi4 - remove unneeded variable
Input: synaptics-rmi4 - remove pointer to rmi_function in f12_data
Input: synaptics-rmi4 - support regulator supplies
Input: raydium_i2c_ts - check CRC of incoming packets
Input: xen-kbdfront - prefer xenbus_write() over xenbus_printf() where possible
Input: fix a double word "is is" in include/linux/input.h
Input: add powerkey driver for HISI 65xx SoC
Input: apanel - spelling mistake - "skiping" -> "skipping"
...
This driver provides a input driver for the power button on the
HiSi 65xx SoC for boards like HiKey.
This driver was originally by Zhiliang Xue <xuezhiliang@huawei.com>
then basically rewritten by Jorge, but preserving the original
module author credits.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
[jstultz: Reworked commit message, folded in other fixes/cleanups
from Jorge, implemented some larger cleanups suggested by DmitryT]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
trivial fix to spelling mistake in pr_notice message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input subsystem updates from Dmitry Torokhov:
"Just a few more driver fixes; new drivers will be coming in the next
merge window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: pwm-beeper - fix - scheduling while atomic
Input: xpad - xbox one elite controller support
Input: xpad - add more third-party controllers
Input: xpad - prevent spurious input from wired Xbox 360 controllers
Input: xpad - move pending clear to the correct location
Input: uinput - handle compat ioctl for UI_SET_PHYS
Johan Hovold
Linus Torvalds
Oleksandr Andrushchenko
Zhuohua Li
Linus Walleij
Deepa Dinamani
Al Viro
Zhen Lei
Dan Carpenter
Dmitry Torokhov
Ingo Molnar
Greg Kroah-Hartman
Mark Rutland
Hans de Goede
Arnd Bergmann
Lee Jones
Sebastian Reichel
Wolfram Sang
Liang Yan
Quentin Schulz
Arvind Yadav
Munir Contractor
Joseph Chen
Juergen Gross
Sebastian Reichel
Martin Kepplinger
Damien Riegel
H. Nikolaus Schaller
Joe Perches
Andy Shevchenko
Jingkui Wang
Guan Ben
Guenter Roeck
David Lechner
Aniroop Mathur
Richard Fitzgerald
Florian Vaussard
Benjamin Tissoires
Javier Martinez Canillas
Steve Twiss
Keerthy
Marcin Niestroj
PrasannaKumar Muralidharan
Vignesh R
Krzysztof Kozlowski
Uwe Kleine-König
Jan Beulich
Jorge Ramirez-Ortiz
Colin Ian King