Граф коммитов

8 Коммитов

Автор SHA1 Сообщение Дата
Thomas Gleixner ec8f24b7fa treewide: Add SPDX license identifier - Makefile/Kconfig
Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21 10:50:46 +02:00
Eddie James 7ed98dddb7 fsi: Add On-Chip Controller (OCC) driver
The OCC is a device embedded on a POWER processor that collects and
aggregates sensor data from the processor and system. The OCC can
provide the raw sensor data as well as perform thermal and power
management on the system.

This driver provides an atomic communications channel between a service
processor (e.g. a BMC) and the OCC. The driver is dependent on the FSI
SBEFIFO driver to get hardware access through the SBE to the OCC SRAM.
Commands are issued to the SBE to send or fetch data to the SRAM.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2018-12-02 16:25:28 -08:00
Benjamin Herrenschmidt 6a794a27da fsi: master-ast-cf: Add new FSI master using Aspeed ColdFire
The Aspeed AST2x00 can contain a ColdFire v1 coprocessor which
is currently unused on OpenPower systems.

This adds an alternative to the fsi-master-gpio driver that
uses that coprocessor instead of bit banging from the ARM
core itself. The end result is about 4 times faster.

The firmware for the coprocessor and its source code can be
found at https://github.com/ozbenh/cf-fsi and is system specific.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2018-07-23 15:22:52 +10:00
Benjamin Herrenschmidt 9f4a8a2d7f fsi/sbefifo: Add driver for the SBE FIFO
This driver provides an in-kernel and a user API for accessing
the command FIFO of the SBE (Self Boot Engine) of the POWER9
processor, via the FSI bus.

It provides an in-kernel interface to submit command and receive
responses, along with a helper to locate and analyse the response
status block. It's a simple synchronous submit() type API.

The user interface uses the write/read interface that an earlier
version of this driver already provided, however it has some
specific limitations in order to keep the driver simple and
avoid using up a lot of kernel memory:

 - The user should perform a single write() with the command and
   a single read() to get the response (with a buffer big enough
   to hold the entire response).

 - On a write() the command is simply "stored" into a kernel buffer,
   it is submitted as one operation on the subsequent read(). This
   allows to have the code write directly from the FIFO into the user
   buffer and avoid hogging the SBE between the write() and read()
   syscall as it's critical that the SBE be freed asap to respond
   to the host. An extra write() will simply replace the previously
   written command.

 - A write of a single 4 bytes containing the value 0x52534554
   in big endian will trigger a reset request. No read is necessary,
   the write() call will return when the reset has been acknowledged
   or times out.

 - The command is limited to 4K bytes.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>
---
2018-06-12 14:05:39 +10:00
Christopher Bostic 7f9e8f7670 drivers/fsi: Add hub master support
Add an engine driver to expose a "hub" FSI master - which has a set of
control registers in the engine address space, and uses a chunk of the
slave address space for actual FSI communication.

Additional changes from Jeremy Kerr <jk@ozlabs.org>.

Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-09 11:52:09 +02:00
Christopher Bostic 680ca6dcf5 drivers/fsi: Add SCOM FSI client device driver
Create a simple SCOM engine device driver that reads and writes
its control registers via an FSI bus.

Includes changes from Edward A. James <eajames@us.ibm.com>.

Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-09 11:52:09 +02:00
Christopher Bostic ac0385d9f6 drivers/fsi: Add GPIO based FSI master
Implement a FSI master using GPIO.  Will generate FSI protocol for
read and write commands to particular addresses.  Sends master command
and waits for and decodes a slave response.

Includes changes from Edward A. James <eajames@us.ibm.com> and Jeremy
Kerr <jk@ozlabs.org>.

Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-09 11:52:09 +02:00
Jeremy Kerr 0508ad1fff drivers/fsi: Add empty fsi bus definitions
This change adds the initial (empty) fsi bus definition, and introduces
drivers/fsi/.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-10 15:19:48 +01:00