* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PIT: free irq source id in handling error path
KVM: destroy workqueue on kvm_create_pit() failures
KVM: fix poison overwritten caused by using wrong xstate size
fpu.state is allocated from task_xstate_cachep, the size of task_xstate_cachep
is xstate_size. xstate_size is set from cpuid instruction, which is often
smaller than sizeof(struct xsave_struct). kvm is using sizeof(struct xsave_struct)
to fill in/out fpu.state.xsave, as what we allocated for fpu.state is
xstate_size, kernel will write out of memory and caused poison/redzone/padding
overwritten warnings.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Reviewed-by: Sheng Yang <sheng@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Sheng Yang <sheng@linux.intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the destination is a memory operand and the memory cannot
map to a valid page, the xchg instruction emulation and locked
instruction will not work on io regions and stuck in endless
loop. We should emulate exchange as write to fix it.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
With tdp enabled we should get into emulator only when emulating io, so
reexecution will always bring us back into emulator.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Userspace needs to reset and save/restore these MSRs.
The MCE banks are not exposed since their number varies from vcpu to vcpu.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When shadow pages are in use sometimes KVM try to emulate an instruction
when it accesses a shadowed page. If emulation fails KVM un-shadows the
page and reenter guest to allow vcpu to execute the instruction. If page
is not in shadow page hash KVM assumes that this was attempt to do MMIO
and reports emulation failure to userspace since there is no way to fix
the situation. This logic has a race though. If two vcpus tries to write
to the same shadowed page simultaneously both will enter emulator, but
only one of them will find the page in shadow page hash since the one who
founds it also removes it from there, so another cpu will report failure
to userspace and will abort the guest.
Fix this by checking (in addition to checking shadowed page hash) that
page that caused the emulation belongs to valid memory slot. If it is
then reenter the guest to allow vcpu to reexecute the instruction.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some guest device driver may leverage the "Non-Snoop" I/O, and explicitly
WBINVD or CLFLUSH to a RAM space. Since migration may occur before WBINVD or
CLFLUSH, we need to maintain data consistency either by:
1: flushing cache (wbinvd) when the guest is scheduled out if there is no
wbinvd exit, or
2: execute wbinvd on all dirty physical CPUs when guest wbinvd exits.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
No need to reload the mmu in between two different vcpu->requests checks.
kvm_mmu_reload() may trigger KVM_REQ_TRIPLE_FAULT, but that will be caught
during atomic guest entry later.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Enable Intel(R) Advanced Vector Extension(AVX) for guest.
The detection of AVX feature includes OSXSAVE bit testing. When OSXSAVE bit is
not set, even if AVX is supported, the AVX instruction would result in UD as
well. So we're safe to expose AVX bits to guest directly.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If a process with a memory slot is COWed, the page will change its address
(despite having an elevated reference count). This breaks internal memory
slots which have their physical addresses loaded into vmcs registers (see
the APIC access memory slot).
Signed-off-by: Avi Kivity <avi@redhat.com>
As advertised in feature-removal-schedule.txt. Equivalent support is provided
by overlapping memory regions.
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of three temporary variables and three free calls, have one temporary
variable (with four names) and one free call.
Signed-off-by: Avi Kivity <avi@redhat.com>
On Intel, we call skip_emulated_instruction() even if we injected a #GP,
resulting in the #GP pointing at the wrong address.
Fix by injecting the exception and skipping the instruction at the same place,
so we can do just one or the other.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On Intel, we call skip_emulated_instruction() even if we injected a #GP,
resulting in the #GP pointing at the wrong address.
Fix by injecting the exception and skipping the instruction at the same place,
so we can do just one or the other.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On Intel, we call skip_emulated_instruction() even if we injected a #GP,
resulting in the #GP pointing at the wrong address.
Fix by injecting the exception and skipping the instruction at the same place,
so we can do just one or the other.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch enable guest to use XSAVE/XRSTOR instructions.
We assume that host_xcr0 would use all possible bits that OS supported.
And we loaded xcr0 in the same way we handled fpu - do it as late as we can.
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Should use linux/uaccess.h instead of asm/uaccess.h
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Memory allocation may fail. Propagate such errors.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We can avoid unnecessary fpu load when userspace process
didn't use FPU frequently.
Derived from Avi's idea.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Now that all arch specific ioctls have centralized locking, it is easy to
move it to the central dispatcher.
Signed-off-by: Avi Kivity <avi@redhat.com>
All vcpu ioctls need to be locked, so instead of locking each one specifically
we lock at the generic dispatcher.
This patch only updates generic ioctls and leaves arch specific ioctls alone.
Signed-off-by: Avi Kivity <avi@redhat.com>
Only modifying some bits of CR0/CR4 needs paging mode switch.
Modify EFER.NXE bit would result in reserved bit updates.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
mmu.free() already set root_hpa to INVALID_PAGE, no need to do it again in the
destory_kvm_mmu().
kvm_x86_ops->set_cr4() and set_efer() already assign cr4/efer to
vcpu->arch.cr4/efer, no need to do it again later.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Do not kill VM when instruction emulation fails. Inject #UD and report
failure to userspace instead. Userspace may choose to reenter guest if
vcpu is in userspace (cpl == 3) in which case guest OS will kill
offending process and continue running.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
KVM_REQ_KICK poisons vcpu->requests by having a bit set during normal
operation. This causes the fast path check for a clear vcpu->requests
to fail all the time, triggering tons of atomic operations.
Fix by replacing KVM_REQ_KICK with a vcpu->guest_mode atomic.
Signed-off-by: Avi Kivity <avi@redhat.com>
Return exception as a result of instruction emulation and handle
injection in KVM code.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Return new RIP as part of instruction emulation result instead of
updating KVM's RIP from x86 emulator code.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Return error to x86 emulator instead of injection exception behind its back.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
It is not called directly outside of the file it's defined in anymore.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently emulator returns -1 when emulation failed or IO is needed.
Caller tries to guess whether emulation failed by looking at other
variables. Make it easier for caller to recognise error condition by
always returning -1 in case of failure. For this new emulator
internal return value X86EMUL_IO_NEEDED is introduced. It is used to
distinguish between error condition (which returns X86EMUL_UNHANDLEABLE)
and condition that requires IO exit to userspace to continue emulation.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fill in run->mmio details in (read|write)_emulated function just like
pio does. There is no point in filling only vcpu fields there just to
copy them into vcpu->run a little bit later.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Make (get|set)_dr() callback return error if it fails instead of
injecting exception behind emulator's back.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Make set_cr() callback return error if it fails instead of injecting #GP
behind emulator's back.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
On VMX it is expensive to call get_cached_descriptor() just to get segment
base since multiple vmcs_reads are done instead of only one. Introduce
new call back get_cached_segment_base() for efficiency.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add (set|get)_msr callbacks to x86_emulate_ops instead of calling
them directly.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add (set|get)_dr callbacks to x86_emulate_ops instead of calling
them directly.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
cr0.ts may change between entries, so we copy cr0 to HOST_CR0 before each
entry. That is slow, so instead, set HOST_CR0 to have TS set unconditionally
(which is a safe value), and issue a clts() just before exiting vcpu context
if the task indeed owns the fpu.
Saves ~50 cycles/exit.
Signed-off-by: Avi Kivity <avi@redhat.com>
Although we always allocate a new dirty bitmap in x86's get_dirty_log(),
it is only used as a zero-source of copy_to_user() and freed right after
that when memslot is clean. This patch uses clear_user() instead of doing
this unnecessary zero-source allocation.
Performance improvement: as we can expect easily, the time needed to
allocate a bitmap is completely reduced. In my test, the improved ioctl
was about 4 to 10 times faster than the original one for clean slots.
Furthermore, reducing memory allocations and copies will produce good
effects to caches too.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
MSR_K6_EFER is unused, and MSR_K6_STAR is redundant with MSR_STAR.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1279371808-24804-1-git-send-email-brgerst@gmail.com>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'kvm-updates/2.6.35' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (269 commits)
KVM: x86: Add missing locking to arch specific vcpu ioctls
KVM: PPC: Add missing vcpu_load()/vcpu_put() in vcpu ioctls
KVM: MMU: Segregate shadow pages with different cr0.wp
KVM: x86: Check LMA bit before set_efer
KVM: Don't allow lmsw to clear cr0.pe
KVM: Add cpuid.txt file
KVM: x86: Tell the guest we'll warn it about tsc stability
x86, paravirt: don't compute pvclock adjustments if we trust the tsc
x86: KVM guest: Try using new kvm clock msrs
KVM: x86: export paravirtual cpuid flags in KVM_GET_SUPPORTED_CPUID
KVM: x86: add new KVMCLOCK cpuid feature
KVM: x86: change msr numbers for kvmclock
x86, paravirt: Add a global synchronization point for pvclock
x86, paravirt: Enable pvclock flags in vcpu_time_info structure
KVM: x86: Inject #GP with the right rip on efer writes
KVM: SVM: Don't allow nested guest to VMMCALL into host
KVM: x86: Fix exception reinjection forced to true
KVM: Fix wallclock version writing race
KVM: MMU: Don't read pdptrs with mmu spinlock held in mmu_alloc_roots
KVM: VMX: enable VMXON check with SMX enabled (Intel TXT)
...
kvm_x86_ops->set_efer() would execute vcpu->arch.efer = efer, so the
checking of LMA bit didn't work.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The current lmsw implementation allows the guest to clear cr0.pe, contrary
to the manual, which breaks EMM386.EXE.
Fix by ORing the old cr0.pe with lmsw's operand.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch puts up the flag that tells the guest that we'll warn it
about the tsc being trustworthy or not. By now, we also say
it is not.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Right now, we were using individual KVM_CAP entities to communicate
userspace about which cpuids we support. This is suboptimal, since it
generates a delay between the feature arriving in the host, and
being available at the guest.
A much better mechanism is to list para features in KVM_GET_SUPPORTED_CPUID.
This makes userspace automatically aware of what we provide. And if we
ever add a new cpuid bit in the future, we have to do that again,
which create some complexity and delay in feature adoption.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Avi pointed out a while ago that those MSRs falls into the pentium
PMU range. So the idea here is to add new ones, and after a while,
deprecate the old ones.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch fixes a bug in the KVM efer-msr write path. If a
guest writes to a reserved efer bit the set_efer function
injects the #GP directly. The architecture dependent wrmsr
function does not see this, assumes success and advances the
rip. This results in a #GP in the guest with the wrong rip.
This patch fixes this by reporting efer write errors back to
the architectural wrmsr function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The patch merged recently which allowed to mark an exception
as reinjected has a bug as it always marks the exception as
reinjected. This breaks nested-svm shadow-on-shadow
implementation.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Wallclock writing uses an unprotected global variable to hold the version;
this can cause one guest to interfere with another if both write their
wallclock at the same time.
Acked-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The recent changes to emulate string instructions without entering guest
mode exposed a bug where pending interrupts are not properly reflected
in ready_for_interrupt_injection.
The result is that userspace overwrites a previously queued interrupt,
when irqchip's are emulated in userspace.
Fix by always updating state before returning to userspace.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (311 commits)
perf tools: Add mode to build without newt support
perf symbols: symbol inconsistency message should be done only at verbose=1
perf tui: Add explicit -lslang option
perf options: Type check all the remaining OPT_ variants
perf options: Type check OPT_BOOLEAN and fix the offenders
perf options: Check v type in OPT_U?INTEGER
perf options: Introduce OPT_UINTEGER
perf tui: Add workaround for slang < 2.1.4
perf record: Fix bug mismatch with -c option definition
perf options: Introduce OPT_U64
perf tui: Add help window to show key associations
perf tui: Make <- exit menus too
perf newt: Add single key shortcuts for zoom into DSO and threads
perf newt: Exit browser unconditionally when CTRL+C, q or Q is pressed
perf newt: Fix the 'A'/'a' shortcut for annotate
perf newt: Make <- exit the ui_browser
x86, perf: P4 PMU - fix counters management logic
perf newt: Make <- zoom out filters
perf report: Report number of events, not samples
perf hist: Clarify events_stats fields usage
...
Fix up trivial conflicts in kernel/fork.c and tools/perf/builtin-record.c
This patch adds logic to kvm/x86 which allows to mark an
injected exception as reinjected. This allows to remove an
ugly hack from svm_complete_interrupts that prevented
exceptions from being reinjected at all in the nested case.
The hack was necessary because an reinjected exception into
the nested guest could cause a nested vmexit emulation. But
reinjected exceptions must not intercept. The downside of
the hack is that a exception that in injected could get
lost.
This patch fixes the problem and puts the code for it into
generic x86 files because. Nested-VMX will likely have the
same problem and could reuse the code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the get_supported_cpuid callback to
kvm_x86_ops. It will be used in do_cpuid_ent to delegate the
decission about some supported cpuid bits to the
architecture modules.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since commit bf47a760f6, we no longer handle ptes with the global bit
set specially, so there is no reason to distinguish between shadow pages
created with cr4.gpe set and clear.
Such tracking is expensive when the guest toggles cr4.pge, so drop it.
Signed-off-by: Avi Kivity <avi@redhat.com>
emulator_task_switch() should return -1 for failure and 0 for success to
the caller, just like x86_emulate_insn() does.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When a fault triggers a task switch, the error code, if existent, has to
be pushed on the new task's stack. Implement the missing bits.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We can call kvm_mmu_pte_write() directly from
emulator_cmpxchg_emulated() instead of passing mmu_only down to
emulator_write_emulated_onepage() and call it there.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently both SVM and VMX have their own DR handling code. Move it to
x86.c.
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
MAXPHYADDR is derived from cpuid 0x80000008, but when that isn't present, we
get some random value.
Fix by checking first that cpuid 0x80000008 is supported.
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Log emulated instructions in ftrace, especially if they failed.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Make sure that rflags is committed only after successful instruction
emulation.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Unify all conditions that get us back into emulator after returning from
userspace.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently when string instruction is only partially complete we go back
to a guest mode, guest tries to reexecute instruction and exits again
and at this point emulation continues. Avoid all of this by restarting
instruction without going back to a guest mode, but return to a guest
mode each 1024 iterations to allow interrupt injection. Pending
exception causes immediate guest entry too.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently emulation is done outside of emulator so things like doing
ins/outs to/from mmio are broken it also makes it hard (if not impossible)
to implement single stepping in the future. The implementation in this
patch is not efficient since it exits to userspace for each IO while
previous implementation did 'ins' in batches. Further patch that
implements pio in string read ahead address this problem.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
in/out emulation is broken now. The breakage is different depending
on where IO device resides. If it is in userspace emulator reports
emulation failure since it incorrectly interprets kvm_emulate_pio()
return value. If IO device is in the kernel emulation of 'in' will do
nothing since kvm_emulate_pio() stores result directly into vcpu
registers, so emulator will overwrite result of emulation during
commit of shadowed register.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Eliminate the need to call back into KVM to get it from emulator.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Use this callback instead of directly call kvm function. Also rename
realmode_(set|get)_cr to emulator_(set|get)_cr since function has nothing
to do with real mode.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Mov reg, cr instruction doesn't change flags in any meaningful way, so
no need to update rflags after instruction execution.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently emulated atomic operations are immediately followed by a non-atomic
operation, so that kvm_mmu_pte_write() can be invoked. This updates the mmu
but undoes the whole point of doing things atomically.
Fix by only performing the atomic operation and the mmu update, and avoiding
the non-atomic write.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Once upon a time, locked operations were emulated while holding the mmu mutex.
Since mmu pages were write protected, it was safe to emulate the writes in
a non-atomic manner, since there could be no other writer, either in the
guest or in the kernel.
These days emulation takes place without holding the mmu spinlock, so the
write could be preempted by an unshadowing event, which exposes the page
to writes by the guest. This may cause corruption of guest page tables.
Fix by using an atomic cmpxchg for these operations.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If no irq chip in kernel, ioctl KVM_IRQ_LINE will return -EFAULT.
But I see in other place such as KVM_[GET|SET]IRQCHIP, -ENXIO is
return. So this patch used -ENXIO instead of -EFAULT.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch does:
- no need call tracepoint_synchronize_unregister() when kvm module
is unloaded since ftrace can handle it
- cleanup ftrace's macro
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
cpuid_update may operate VMCS, so vcpu_load() and vcpu_put()
should be called to ensure correctness.
Signed-off-by: Dongxiao Xu <dongxiao.xu@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
fix segment_base() to properly check for null segment selector and
avoid accessing NULL pointer if ldt selector in null.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Linux now has native_store_gdt() to do the same. Use it instead of
kvm local version.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The vcpu->arch.cr0 variable is already set in the
architecture specific set_cr0 callbacks. There is no need to
set it in the common code.
This allows the architecture code to keep the old arch.cr0
value if it wants. This is required for nested svm to decide
if a selective_cr0 exit needs to be injected.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Hyper-V as a guest wants to write this bit. This patch
ignores it.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds a tracepoint to get information about the
most important intercept bitmasks from the nested vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Call directly into the vendor services for getting/setting rflags in
emulate_instruction to ensure injected TF survives the emulation.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
RF is not required for injecting TF as the latter will trigger only
after an instruction execution anyway. So do not touch RF when arming or
disarming guest single-step mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Based on Gleb's suggestion: Add a helper kvm_is_linear_rip that matches
a given linear RIP against the current one. Use this for guest
single-stepping, more users will follow.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far user space was not able to save and restore debug registers for
migration or after reset. Plug this hole.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The interrupt shadow created by STI or MOV-SS-like operations is part of
the VCPU state and must be preserved across migration. Transfer it in
the spare padding field of kvm_vcpu_events.interrupt.
As a side effect we now have to make vmx_set_interrupt_shadow robust
against both shadow types being set. Give MOV SS a higher priority and
skip STI in that case to avoid that VMX throws a fault on next entry.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
To avoid that user space migrates a pending software exception or
interrupt, mask them out on KVM_GET_VCPU_EVENTS. Without this, user
space would try to reinject them, and we would have to reconstruct the
proper instruction length for VMX event injection. Now the pending event
will be reinjected via executing the triggering instruction again.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
vcpu->run is initialized on vcpu creation and can never be NULL
here.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
x86 arch defines desc_ptr for idt/gdt pointers, no need to define
another structure in kvm code.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
A 16-bit TSS is only 44 bytes long. So make sure to test for the correct
size on task switch.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Int is not long enough to store the size of a dirty bitmap.
This patch fixes this problem with the introduction of a wrapper
function to calculate the sizes of dirty bitmaps.
Note: in mark_page_dirty(), we have to consider the fact that
__set_bit() takes the offset as int, not long.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
There is a quirk for AMD K8 CPUs in many Linux kernels (see
arch/x86/kernel/cpu/mcheck/mce.c:__mcheck_cpu_apply_quirks()) that
clears bit 10 in that MCE related MSR. KVM can only cope with all
zeros or all ones, so it will inject a #GP into the guest, which
will let it panic.
So lets add a quirk to the quirk and ignore this single cleared bit.
This fixes -cpu kvm64 on all machines and -cpu host on K8 machines
with some guest Linux kernels.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
complete_pio() may use slot table which is protected by srcu.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Below patch implements the perf_guest_info_callbacks on kvm.
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This marks the guest single-step API improvement of 94fe45da and
91586a3b with a capability flag to allow reliable detection by user
space.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: stable@kernel.org (2.6.33)
Signed-off-by: Avi Kivity <avi@redhat.com>
Add proper error and permission checking. This patch also change task
switching code to load segment selectors before segment descriptors, like
SDM requires, otherwise permission checking during segment descriptor
loading will be incorrect.
Cc: stable@kernel.org (2.6.33, 2.6.32)
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch injects page fault when reading descriptor in
load_guest_segment_descriptor() fails with FAULT.
Effects of this injection: This function is used by
kvm_load_segment_descriptor() which is necessary for the
following instructions:
- mov seg,r/m16
- jmp far
- pop ?s
This patch makes it possible to emulate the page faults
generated by these instructions. But be sure that unless
we change the kvm_load_segment_descriptor()'s ret value
propagation this patch has no effect.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The i8254/i8259 locks need to be real spinlocks on preempt-rt. Convert
them to raw_spinlock. No change for !RT kernels.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Make emulator check that vcpu is allowed to execute IN, INS, OUT,
OUTS, CLI, STI.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently when x86 emulator needs to access memory, page walk is done with
broadest permission possible, so if emulated instruction was executed
by userspace process it can still access kernel memory. Fix that by
providing correct memory access to page walker during emulation.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
For some instructions CPU behaves differently for real-mode and
virtual 8086. Let emulator know which mode cpu is in, so it will
not poke into vcpu state directly.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
If we fail to init ioapic device or the fail to setup the default irq
routing, the device register by kvm_create_pic() and kvm_ioapic_init()
remain unregister. This patch fixed to do this.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_emulate_pio() and complete_pio() both read out the
RAX register value and copy it to a place into which
the value read out from the port will be copied later.
This patch removes this redundancy.
/*** snippet from arch/x86/kvm/x86.c ***/
int complete_pio(struct kvm_vcpu *vcpu)
{
...
if (!io->string) {
if (io->in) {
val = kvm_register_read(vcpu, VCPU_REGS_RAX);
memcpy(&val, vcpu->arch.pio_data, io->size);
kvm_register_write(vcpu, VCPU_REGS_RAX, val);
}
...
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch fixes kvm_fix_hypercall() to propagate X86EMUL_*
info generated by emulator_write_emulated() to its callers:
suggested by Marcelo.
The effect of this is x86_emulate_insn() will begin to handle
the page faults which occur in emulator_write_emulated():
this should be OK because emulator_write_emulated_onepage()
always injects page fault when emulator_write_emulated()
returns X86EMUL_PROPAGATE_FAULT.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch fixes load_guest_segment_descriptor() to return
X86EMUL_PROPAGATE_FAULT when it tries to access the descriptor
table beyond the limit of it: suggested by Marcelo.
I have checked current callers of this helper function,
- kvm_load_segment_descriptor()
- kvm_task_switch()
and confirmed that this patch will change nothing in the
upper layers if we do not change the handling of this
return value from load_guest_segment_descriptor().
Next step: Although fixing the kvm_task_switch() to handle the
propagated faults properly seems difficult, and maybe not worth
it because TSS is not used commonly these days, we can fix
kvm_load_segment_descriptor(). By doing so, the injected #GP
becomes possible to be handled by the guest. The only problem
for this is how to differentiate this fault from the page faults
generated by kvm_read_guest_virt(). We may have to split this
function to achive this goal.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On HW task switch newly loaded segments should me marked as accessed.
Reported-by: Lorenzo Martignoni <martignlo@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Assume that if the guest executes clts, it knows what it's doing, and load the
guest fpu to prevent an #NM exception.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This allows accessing the guest fpu from the instruction emulator, as well as
being symmetric with kvm_put_guest_fpu().
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Move to/from Control Registers chapter of Intel SDM says. "Reserved bits
in CR0 remain clear after any load of those registers; attempts to set
them have no impact". Control Register chapter says "Bits 63:32 of CR0 are
reserved and must be written with zeros. Writing a nonzero value to any
of the upper 32 bits results in a general-protection exception, #GP(0)."
This patch tries to implement this twisted logic.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Reported-by: Lorenzo Martignoni <martignlo@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Enhance mov dr instruction emulation used by SVM so that it properly
handles dr4/5: alias to dr6/7 if cr4.de is cleared. Otherwise return
EMULATE_FAIL which will let our only possible caller in that scenario,
ud_interception, re-inject UD.
We do not need to inject faults, SVM does this for us (exceptions take
precedence over instruction interceptions). For the same reason, the
value overflow checks can be removed.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Windows issues this hypercall after guest was spinning on a spinlock
for too many iterations.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Vadim Rozenfeld <vrozenfe@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Defer fpu deactivation as much as possible - if the guest fpu is loaded, keep
it loaded until the next heavyweight exit (where we are forced to unload it).
This reduces unnecessary exits.
We also defer fpu activation on clts; while clts signals the intent to use the
fpu, we can't be sure the guest will actually use it.
Signed-off-by: Avi Kivity <avi@redhat.com>
Since we'd like to allow the guest to own a few bits of cr0 at times, we need
to know when we access those bits.
Signed-off-by: Avi Kivity <avi@redhat.com>
Then the callback can provide the maximum supported large page level, which
is more flexible.
Also move the gb page support into x86_64 specific.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Have a pointer to an allocated region inside struct kvm.
[alex: fix ppc book 3s]
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Before enabling, execution of "rdtscp" in guest would result in #UD.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Sometime, we need to adjust some state in order to reflect guest CPUID
setting, e.g. if we don't expose rdtscp to guest, we won't want to enable
it on hardware. cpuid_update() is introduced for this purpose.
Also export kvm_find_cpuid_entry() for later use.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
shared_msr_global saved host value of relevant MSRs, but it have an
assumption that all MSRs it tracked shared the value across the different
CPUs. It's not true with some MSRs, e.g. MSR_TSC_AUX.
Extend it to per CPU to provide the support of MSR_TSC_AUX, and more
alike MSRs.
Notice now the shared_msr_global still have one assumption: it can only deal
with the MSRs that won't change in host after KVM module loaded.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some bits of cr4 can be owned by the guest on vmx, so when we read them,
we copy them to the vcpu structure. In preparation for making the set of
guest-owned bits dynamic, use helpers to access these bits so we don't need
to know where the bit resides.
No changes to svm since all bits are host-owned there.
Signed-off-by: Avi Kivity <avi@redhat.com>
Windows 2003 uses task switch to triple fault and reboot (the other
exception being reserved pdptrs bits).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Move Double-Fault generation logic out of page fault
exception generating function to cover more generic case.
Signed-off-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Current kvm wallclock does not consider the total_sleep_time which could cause
wrong wallclock in guest after host suspend/resume. This patch solve
this issue by counting total_sleep_time to get the correct host boot time.
Cc: stable@kernel.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In function kvm_arch_vcpu_init(), if the memory malloc for
vcpu->arch.mce_banks is fail, it does not free the memory
of lapic date. This patch fixed it.
Cc: stable@kernel.org
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
vcpu->arch.mce_banks is malloc in kvm_arch_vcpu_init(), but
never free in any place, this may cause memory leak. So this
patch fixed to free it in kvm_arch_vcpu_uninit().
Cc: stable@kernel.org
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
User space may not want to overwrite asynchronously changing VCPU event
states on write-back. So allow to skip nmi.pending and sipi_vector by
setting corresponding bits in the flags field of kvm_vcpu_events.
[avi: advertise the bits in KVM_GET_VCPU_EVENTS]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (84 commits)
KVM: VMX: Fix comparison of guest efer with stale host value
KVM: s390: Fix prefix register checking in arch/s390/kvm/sigp.c
KVM: Drop user return notifier when disabling virtualization on a cpu
KVM: VMX: Disable unrestricted guest when EPT disabled
KVM: x86 emulator: limit instructions to 15 bytes
KVM: s390: Make psw available on all exits, not just a subset
KVM: x86: Add KVM_GET/SET_VCPU_EVENTS
KVM: VMX: Report unexpected simultaneous exceptions as internal errors
KVM: Allow internal errors reported to userspace to carry extra data
KVM: Reorder IOCTLs in main kvm.h
KVM: x86: Polish exception injection via KVM_SET_GUEST_DEBUG
KVM: only clear irq_source_id if irqchip is present
KVM: x86: disallow KVM_{SET,GET}_LAPIC without allocated in-kernel lapic
KVM: x86: disallow multiple KVM_CREATE_IRQCHIP
KVM: VMX: Remove vmx->msr_offset_efer
KVM: MMU: update invlpg handler comment
KVM: VMX: move CR3/PDPTR update to vmx_set_cr3
KVM: remove duplicated task_switch check
KVM: powerpc: Fix BUILD_BUG_ON condition
KVM: VMX: Use shared msr infrastructure
...
Trivial conflicts due to new Kconfig options in arch/Kconfig and kernel/Makefile
update_transition_efer() masks out some efer bits when deciding whether
to switch the msr during guest entry; for example, NX is emulated using the
mmu so we don't need to disable it, and LMA/LME are handled by the hardware.
However, with shared msrs, the comparison is made against a stale value;
at the time of the guest switch we may be running with another guest's efer.
Fix by deferring the mask/compare to the actual point of guest entry.
Noted by Marcelo.
Signed-off-by: Avi Kivity <avi@redhat.com>
This way, we don't leave a dangling notifier on cpu hotunplug or module
unload. In particular, module unload leaves the notifier pointing into
freed memory.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This new IOCTL exports all yet user-invisible states related to
exceptions, interrupts, and NMIs. Together with appropriate user space
changes, this fixes sporadic problems of vmsave/restore, live migration
and system reset.
[avi: future-proof abi by adding a flags field]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Decouple KVM_GUESTDBG_INJECT_DB and KVM_GUESTDBG_INJECT_BP from
KVM_GUESTDBG_ENABLE, their are actually orthogonal. At this chance,
avoid triggering the WARN_ON in kvm_queue_exception if there is already
an exception pending and reject such invalid requests.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Otherwise kvm will leak memory on multiple KVM_CREATE_IRQCHIP.
Also serialize multiple accesses with kvm->lock.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
GUEST_CR3 is updated via kvm_set_cr3 whenever CR3 is modified from
outside guest context. Similarly pdptrs are updated via load_pdptrs.
Let kvm_set_cr3 perform the update, removing it from the vcpu_run
fast path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Acked-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The various syscall-related MSRs are fairly expensive to switch. Currently
we switch them on every vcpu preemption, which is far too often:
- if we're switching to a kernel thread (idle task, threaded interrupt,
kernel-mode virtio server (vhost-net), for example) and back, then
there's no need to switch those MSRs since kernel threasd won't
be exiting to userspace.
- if we're switching to another guest running an identical OS, most likely
those MSRs will have the same value, so there's little point in reloading
them.
- if we're running the same OS on the guest and host, the MSRs will have
identical values and reloading is unnecessary.
This patch uses the new user return notifiers to implement last-minute
switching, and checks the msr values to avoid unnecessary reloading.
Signed-off-by: Avi Kivity <avi@redhat.com>
When we migrate a kvm guest that uses pvclock between two hosts, we may
suffer a large skew. This is because there can be significant differences
between the monotonic clock of the hosts involved. When a new host with
a much larger monotonic time starts running the guest, the view of time
will be significantly impacted.
Situation is much worse when we do the opposite, and migrate to a host with
a smaller monotonic clock.
This proposed ioctl will allow userspace to inform us what is the monotonic
clock value in the source host, so we can keep the time skew short, and
more importantly, never goes backwards. Userspace may also need to trigger
the current data, since from the first migration onwards, it won't be
reflected by a simple call to clock_gettime() anymore.
[marcelo: future-proof abi with a flags field]
[jan: fix KVM_GET_CLOCK by clearing flags field instead of checking it]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit 705c5323 opened the doors of hell by unconditionally injecting
single-step flags as long as guest_debug signaled this. This doesn't
work when the guest branches into some interrupt or exception handler
and triggers a vmexit with flag reloading.
Fix it by saving cs:rip when user space requests single-stepping and
restricting the trace flag injection to this guest code position.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Support for Xen PV-on-HVM guests can be implemented almost entirely in
userspace, except for handling one annoying MSR that maps a Xen
hypercall blob into guest address space.
A generic mechanism to delegate MSR writes to userspace seems overkill
and risks encouraging similar MSR abuse in the future. Thus this patch
adds special support for the Xen HVM MSR.
I implemented a new ioctl, KVM_XEN_HVM_CONFIG, that lets userspace tell
KVM which MSR the guest will write to, as well as the starting address
and size of the hypercall blobs (one each for 32-bit and 64-bit) that
userspace has loaded from files. When the guest writes to the MSR, KVM
copies one page of the blob from userspace to the guest.
I've tested this patch with a hacked-up version of Gerd's userspace
code, booting a number of guests (CentOS 5.3 i386 and x86_64, and
FreeBSD 8.0-RC1 amd64) and exercising PV network and block devices.
[jan: fix i386 build warning]
[avi: future proof abi with a flags field]
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This (broken) check dates back to the days when this code was shared
across architectures. x86 has IOMEM, so drop it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If cpufreq can't determine the CPU khz, or cpufreq is not compiled in,
we should fallback to the measured TSC khz.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a tracepoint for the event that the guest
executed the SKINIT instruction. This information is
important because SKINIT is an SVM extenstion not yet
implemented by nested SVM and we may need this information
for debugging hypervisors that do not yet run on nested SVM.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a tracepoint for the event that the guest
executed the INVLPGA instruction.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a special tracepoint for the event that a
nested #vmexit is injected because kvm wants to inject an
interrupt into the guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a tracepoint for a nested #vmexit that gets
re-injected to the guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a tracepoint for every #vmexit we get from a
nested guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a dedicated kvm tracepoint for a nested
vmrun.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
For a while now, we are issuing a rdmsr instruction to find out which
msrs in our save list are really supported by the underlying machine.
However, it fails to account for kvm-specific msrs, such as the pvclock
ones.
This patch moves then to the beginning of the list, and skip testing them.
Cc: stable@kernel.org
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Push TF and RF injection and filtering on guest single-stepping into the
vender get/set_rflags callbacks. This makes the whole mechanism more
robust wrt user space IOCTL order and instruction emulations.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Disable paravirt MMU capability reporting, so that new (or rebooted)
guests switch to native operation.
Paravirt MMU is a burden to maintain and does not bring significant
advantages compared to shadow anymore.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Much of so far vendor-specific code for setting up guest debug can
actually be handled by the generic code. This also fixes a minor deficit
in the SVM part /wrt processing KVM_GUESTDBG_ENABLE.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
They are globals, not clearly protected by any ordering or locking, and
vulnerable to various startup races.
Instead, for variable TSC machines, register the cpufreq notifier and get
the TSC frequency directly from the cpufreq machinery. Not only is it
always right, it is also perfectly accurate, as no error prone measurement
is required.
On such machines, when a new CPU online is brought online, it isn't clear what
frequency it will start with, and it may not correspond to the reference, thus
in hardware_enable we clear the cpu_tsc_khz variable to zero and make sure
it is set before running on a VCPU.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
X86 CPUs need to have some magic happening to enable the virtualization
extensions on them. This magic can result in unpleasant results for
users, like blocking other VMMs from working (vmx) or using invalid TLB
entries (svm).
Currently KVM activates virtualization when the respective kernel module
is loaded. This blocks us from autoloading KVM modules without breaking
other VMMs.
To circumvent this problem at least a bit, this patch introduces on
demand activation of virtualization. This means, that instead
virtualization is enabled on creation of the first virtual machine
and disabled on destruction of the last one.
So using this, KVM can be easily autoloaded, while keeping other
hypervisors usable.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The only thing it protects now is interrupt injection into lapic and
this can work lockless. Even now with kvm->irq_lock in place access
to lapic is not entirely serialized since vcpu access doesn't take
kvm->irq_lock.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Conflicts:
arch/x86/kernel/kprobes.c
kernel/trace/Makefile
Merge reason: hw-breakpoints perf integration is looking
good in testing and in reviews, plus conflicts
are mounting up - so merge & resolve.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Wrap in the cpu dr7 check that tells if we have active
breakpoints that need to be restored in the cpu.
This wrapper makes the check more self-explainable and also
reusable for any further other uses.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: "K. Prasad" <prasad@linux.vnet.ibm.com>
This patch rebase the implementation of the breakpoints API on top of
perf events instances.
Each breakpoints are now perf events that handle the
register scheduling, thread/cpu attachment, etc..
The new layering is now made as follows:
ptrace kgdb ftrace perf syscall
\ | / /
\ | / /
/
Core breakpoint API /
/
| /
| /
Breakpoints perf events
|
|
Breakpoints PMU ---- Debug Register constraints handling
(Part of core breakpoint API)
|
|
Hardware debug registers
Reasons of this rewrite:
- Use the centralized/optimized pmu registers scheduling,
implying an easier arch integration
- More powerful register handling: perf attributes (pinned/flexible
events, exclusive/non-exclusive, tunable period, etc...)
Impact:
- New perf ABI: the hardware breakpoints counters
- Ptrace breakpoints setting remains tricky and still needs some per
thread breakpoints references.
Todo (in the order):
- Support breakpoints perf counter events for perf tools (ie: implement
perf_bpcounter_event())
- Support from perf tools
Changes in v2:
- Follow the perf "event " rename
- The ptrace regression have been fixed (ptrace breakpoint perf events
weren't released when a task ended)
- Drop the struct hw_breakpoint and store generic fields in
perf_event_attr.
- Separate core and arch specific headers, drop
asm-generic/hw_breakpoint.h and create linux/hw_breakpoint.h
- Use new generic len/type for breakpoint
- Handle off case: when breakpoints api is not supported by an arch
Changes in v3:
- Fix broken CONFIG_KVM, we need to propagate the breakpoint api
changes to kvm when we exit the guest and restore the bp registers
to the host.
Changes in v4:
- Drop the hw_breakpoint_restore() stub as it is only used by KVM
- EXPORT_SYMBOL_GPL hw_breakpoint_restore() as KVM can be built as a
module
- Restore the breakpoints unconditionally on kvm guest exit:
TIF_DEBUG_THREAD doesn't anymore cover every cases of running
breakpoints and vcpu->arch.switch_db_regs might not always be
set when the guest used debug registers.
(Waiting for a reliable optimization)
Changes in v5:
- Split-up the asm-generic/hw-breakpoint.h moving to
linux/hw_breakpoint.h into a separate patch
- Optimize the breakpoints restoring while switching from kvm guest
to host. We only want to restore the state if we have active
breakpoints to the host, otherwise we don't care about messed-up
address registers.
- Add asm/hw_breakpoint.h to Kbuild
- Fix bad breakpoint type in trace_selftest.c
Changes in v6:
- Fix wrong header inclusion in trace.h (triggered a build
error with CONFIG_FTRACE_SELFTEST
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jan Kiszka <jan.kiszka@web.de>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
If TSS we are switching to resides in high memory task switch will fail
since address will be truncated. Windows2k3 does this sometimes when
running with more then 4G
Cc: stable@kernel.org
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We only allocate memory for 32 MCE banks (KVM_MAX_MCE_BANKS) but we
allow user space to fill up to 255 on setup (mcg_cap & 0xff), corrupting
kernel memory. Catch these overflows.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Conflicts:
kernel/Makefile
kernel/trace/Makefile
kernel/trace/trace.h
samples/Makefile
Merge reason: We need to be uptodate with the perf events development
branch because we plan to rewrite the breakpoints API on top of
perf events.
The number of entries is multiplied by the entry size, which can
overflow on 32-bit hosts. Bound the entry count instead.
Reported-by: David Wagner <daw@cs.berkeley.edu>
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (202 commits)
MAINTAINERS: update KVM entry
KVM: correct error-handling code
KVM: fix compile warnings on s390
KVM: VMX: Check cpl before emulating debug register access
KVM: fix misreporting of coalesced interrupts by kvm tracer
KVM: x86: drop duplicate kvm_flush_remote_tlb calls
KVM: VMX: call vmx_load_host_state() only if msr is cached
KVM: VMX: Conditionally reload debug register 6
KVM: Use thread debug register storage instead of kvm specific data
KVM guest: do not batch pte updates from interrupt context
KVM: Fix coalesced interrupt reporting in IOAPIC
KVM guest: fix bogus wallclock physical address calculation
KVM: VMX: Fix cr8 exiting control clobbering by EPT
KVM: Optimize kvm_mmu_unprotect_page_virt() for tdp
KVM: Document KVM_CAP_IRQCHIP
KVM: Protect update_cr8_intercept() when running without an apic
KVM: VMX: Fix EPT with WP bit change during paging
KVM: Use kvm_{read,write}_guest_virt() to read and write segment descriptors
KVM: x86 emulator: Add adc and sbb missing decoder flags
KVM: Add missing #include
...
Debug registers may only be accessed from cpl 0. Unfortunately, vmx will
code to emulate the instruction even though it was issued from guest
userspace, possibly leading to an unexpected trap later.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of saving the debug registers from the processor to a kvm data
structure, rely in the debug registers stored in the thread structure.
This allows us not to save dr6 and dr7.
Reduces lightweight vmexit cost by 350 cycles, or 11 percent.
Signed-off-by: Avi Kivity <avi@redhat.com>
Segment descriptors tables can be placed on two non-contiguous pages.
This patch makes reading segment descriptors by linear address.
Signed-off-by: Mikhail Ershov <Mike.Ershov@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
According to 16.2.5 in the SDM, eflags.vm in the tss is consulted before loading
and new segments. If eflags.vm == 1, then the segments are treated as 16-bit
segments. The LDTR and TR are not normally available in vm86 mode so if they
happen to somehow get loaded, they need to be treated as 32-bit segments.
This fixes an invalid vmentry failure in a custom OS that was happening after
a task switch into vm8086 mode. Since the segments were being mistakenly
treated as 32-bit, we loaded garbage state.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since on vcpu entry we do it only if apic is enabled we should do
it when TPR is changed while apic is disabled. This happens when windows
resets HW without setting TPR to zero.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We ignore writes to the perfctr msrs. Ignore reads as well.
Kaspersky antivirus crashes Windows guests if it can't read
these MSRs.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far unprivileged guest callers running in ring 3 can issue, e.g., MMU
hypercalls. Normally, such callers cannot provide any hand-crafted MMU
command structure as it has to be passed by its physical address, but
they can still crash the guest kernel by passing random addresses.
To close the hole, this patch considers hypercalls valid only if issued
from guest ring 0. This may still be relaxed on a per-hypercall base in
the future once required.
Cc: stable@kernel.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If userspace knows that the kernel part supports 1GB pages it can enable
the corresponding cpuid bit so that guests actually use GB pages.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit f0a3602c20 ("KVM: Move interrupt injection logic to x86.c") does not
update the cr8 intercept if the lapic is disabled, so when userspace updates
cr8, the cr8 threshold control is not updated and we are left with illegal
control fields.
Fix by explicitly resetting the cr8 threshold.
Signed-off-by: Avi Kivity <avi@redhat.com>
Now KVM allow guest to modify guest's physical address of EPT's identity mapping page.
(change from v1, discard unnecessary check, change ioctl to accept parameter
address rather than value)
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Use kvm_get_gdt() and kvm_read_ldt() to reduce inline assembly code.
Cc: Avi Kivity <avi@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Use get_desc_base() and get_desc_limit() to get the base address and
limit in desc_struct.
Cc: Avi Kivity <avi@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Remove kvm_cpu_has_interrupt() and kvm_arch_interrupt_allowed() from
interface between general code and arch code. kvm_arch_vcpu_runnable()
checks for interrupts instead.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
ioeventfd is a mechanism to register PIO/MMIO regions to trigger an eventfd
signal when written to by a guest. Host userspace can register any
arbitrary IO address with a corresponding eventfd and then pass the eventfd
to a specific end-point of interest for handling.
Normal IO requires a blocking round-trip since the operation may cause
side-effects in the emulated model or may return data to the caller.
Therefore, an IO in KVM traps from the guest to the host, causes a VMX/SVM
"heavy-weight" exit back to userspace, and is ultimately serviced by qemu's
device model synchronously before returning control back to the vcpu.
However, there is a subclass of IO which acts purely as a trigger for
other IO (such as to kick off an out-of-band DMA request, etc). For these
patterns, the synchronous call is particularly expensive since we really
only want to simply get our notification transmitted asychronously and
return as quickly as possible. All the sychronous infrastructure to ensure
proper data-dependencies are met in the normal IO case are just unecessary
overhead for signalling. This adds additional computational load on the
system, as well as latency to the signalling path.
Therefore, we provide a mechanism for registration of an in-kernel trigger
point that allows the VCPU to only require a very brief, lightweight
exit just long enough to signal an eventfd. This also means that any
clients compatible with the eventfd interface (which includes userspace
and kernelspace equally well) can now register to be notified. The end
result should be a more flexible and higher performance notification API
for the backend KVM hypervisor and perhipheral components.
To test this theory, we built a test-harness called "doorbell". This
module has a function called "doorbell_ring()" which simply increments a
counter for each time the doorbell is signaled. It supports signalling
from either an eventfd, or an ioctl().
We then wired up two paths to the doorbell: One via QEMU via a registered
io region and through the doorbell ioctl(). The other is direct via
ioeventfd.
You can download this test harness here:
ftp://ftp.novell.com/dev/ghaskins/doorbell.tar.bz2
The measured results are as follows:
qemu-mmio: 110000 iops, 9.09us rtt
ioeventfd-mmio: 200100 iops, 5.00us rtt
ioeventfd-pio: 367300 iops, 2.72us rtt
I didn't measure qemu-pio, because I have to figure out how to register a
PIO region with qemu's device model, and I got lazy. However, for now we
can extrapolate based on the data from the NULLIO runs of +2.56us for MMIO,
and -350ns for HC, we get:
qemu-pio: 153139 iops, 6.53us rtt
ioeventfd-hc: 412585 iops, 2.37us rtt
these are just for fun, for now, until I can gather more data.
Here is a graph for your convenience:
http://developer.novell.com/wiki/images/7/76/Iofd-chart.png
The conclusion to draw is that we save about 4us by skipping the userspace
hop.
--------------------
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When kvm is in hpet_legacy_mode, the hpet is providing the timer
interrupt and the pit should not be. So in legacy mode, the pit timer
is destroyed, but the *state* of the pit is maintained. So if kvm or
the guest tries to modify the state of the pit, this modification is
accepted, *except* that the timer isn't actually started. When we exit
hpet_legacy_mode, the current state of the pit (which is up to date
since we've been accepting modifications) is used to restart the pit
timer.
The saved_mode code in kvm_pit_load_count temporarily changes mode to
0xff in order to destroy the timer, but then restores the actual
value, again maintaining "current" state of the pit for possible later
reenablement.
[avi: add some reserved storage in the ioctl; make SET_PIT2 IOW]
[marcelo: fix memory corruption due to reserved storage]
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We emulate x2apic in software, so host support is not required.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This will save a couple of IPIs.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some Windows versions check whether the BIOS has setup MMI/O for
config space accesses on AMD Fam10h CPUs, we say "no" by returning 0 on
reads and only allow disabling of MMI/O CfgSpace setup by igoring "0" writes.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This reverts commit 6c20e1442bb1c62914bb85b7f4a38973d2a423ba.
To my understanding, it became obsolete with the advent of the more
robust check in mmu_alloc_roots (89da4ff17f). Moreover, it prevents
the conceptually safe pattern
1. set sregs
2. register mem-slots
3. run vcpu
by setting a sticky triple fault during step 1.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Windows 7 tries to update the CPU's microcode on some processors,
so we ignore the MSR write here. The patchlevel register is already handled
(returning 0), because the MSR number is the same as Intel's.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements MSR interface to local apic as defines by x2apic
Intel specification.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Directed EOI is specified by x2APIC, but is available even when lapic is
in xAPIC mode.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Linux guests will try to enable access to the extended PCI config space
via the I/O ports 0xCF8/0xCFC on AMD Fam10h CPU. Since we (currently?)
don't use ECS, simply ignore write and read attempts.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This changes bus accesses to use high-level kvm_io_bus_read/kvm_io_bus_write
functions. in_range now becomes unused so it is removed from device ops in
favor of read/write callbacks performing range checks internally.
This allows aliasing (mostly for in-kernel virtio), as well as better error
handling by making it possible to pass errors up to userspace.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
switch pit creation to slots_lock. slots_lock is already taken for read
everywhere, so we only need to take it for write when creating pit.
This is in preparation to removing in_range and kvm->lock around it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM will inject a #GP into the guest if that tries to access unhandled
MSRs. This will crash many guests. Although it would be the correct
way to actually handle these MSRs, we introduce a runtime switchable
module param called "ignore_msrs" (defaults to 0). If this is Y, unknown
MSR reads will return 0, while MSR writes are simply dropped. In both cases
we print a message to dmesg to inform the user about that.
You can change the behaviour at any time by saying:
# echo 1 > /sys/modules/kvm/parameters/ignore_msrs
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the Linux kernel detects an C1E capable AMD processor (K8 RevF and
higher), it will access a certain MSR on every attempt to go to halt.
Explicitly handle this read and return 0 to let KVM run a Linux guest
with the native AMD host CPU propagated to the guest.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Linux tries to disable the flush filter on all AMD K8 CPUs. Since KVM
does not handle the needed MSR, the injected #GP will panic the Linux
kernel. Ignore setting of the HWCR.FFDIS bit in this MSR to let Linux
boot with an AMD K8 family guest CPU.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Correct missing locking in a few places in x86's vm_ioctl handling path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add the opcodes for syscall, sysenter and sysexit to the list of instructions
handled by the undefined opcode handler.
Signed-off-by: Christoph Egger <christoph.egger@amd.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allows use of the powerful ftrace infrastructure.
See Documentation/trace/ for usage information.
[avi, stephen: various build fixes]
[sheng: fix control register breakage]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Replace previous exception with a new one in a hope that instruction
re-execution will regenerate lost exception.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The performance counter MSRs are different for AMD and Intel CPUs and they
are chosen mainly by the CPUID vendor string. This patch catches writes to
all addresses (regardless of VMX/SVM path) and handles them in the generic
MSR handler routine. Writing a 0 into the event select register is something
we perfectly emulate ;-), so don't print out a warning to dmesg in this
case.
This fixes booting a 64bit Windows guest with an AMD CPUID on an Intel host.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Linus Torvalds
Xiaotian Feng
Wei Yongjun
Gleb Natapov
Avi Kivity
Xiao Guangrong
Sheng Yang
Dexuan Cui
Lai Jiangshan
Jan Kiszka
Takuya Yoshikawa
H. Peter Anvin
Brian Gerst
Glauber Costa
Roedel, Joerg
Marcelo Tosatti
Jan Kiszka
Dongxiao Xu
Ingo Molnar
Andre Przywara
Zhang, Yanmin
Tejun Heo
Thomas Gleixner
Zhai, Edwin
Eddie Dong
Jason Wang
Ed Swierk
Zachary Amsden
Juan Quintela
Alexander Graf
Frederic Weisbecker
Mikhail Ershov
Anthony Liguori
Amit Shah
Mikhail Ershov
Akinobu Mita
Gregory Haskins
Beth Kon
Michael S. Tsirkin
