mxser doesn't increase port->icount.buf_overrun at all. Do so if overrun
happens, so that it can be read from the stats.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-17-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous change (no plays with of tty->receive_room), the tty
parameter is unused.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, checking tty->receive_room to signalize whether there is enough space
in the tty buffers does not make much sense. Provided the tty buffers
are in tty_port and those are not checked at all.
Second, if the rx path is throttled, with CRTSCTS, RTS is deasserted,
but is never asserted again. This leads to port "lockup", not accepting
any more input.
So:
1) stty -F /dev/ttyMI0 crtscts # the mxser port
2) stty -F /dev/ttyS6 crtscts # the connected port
3) cat /dev/ttyMI0
4) "write in a loop" to /dev/ttyS6
5) cat from 3) produces the bytes from 4)
6) killall -STOP cat (the 3)'s one)
7) wait for RTS to drop on /dev/ttyMI0
8) killall -CONT cat (again the 3)'s one)
cat erroneously produces no more output now (i.e. no data sent from
ttyS6 to ttyMI can be seen).
Note that the step 7) is performed twice: once from n_tty by
tty_throttle_safe(), once by mxser_stoprx() from the receive path. Then
after step 7), n_tty correctly unthrottles the input, but mxser calls
mxser_stoprx() again as there is still only a little space in n_tty
buffers (tty->receive_room mentioned at the beginning), but the device's
FIFO is/can be already filled.
After this patch, the output is correctly resumed, i.e. n_tty both
throttles and unthrottles without interfering with mxser's attempts.
This allows us to get rid of the non-standard ldisc_stop_rx flag from
struct mxser_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-15-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timeout cannot be zero at the point of use. So no need to check for
zero. Also precompute the expiration time (into expire) and use it. This
makes the code more clear.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-14-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of schedule_timeout_interruptible(), because:
1) we don't have to bother with the task state, and
2) msleep* guarantees to sleep that time (if not interrupted).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-13-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And move it to new mxser_tx_empty(), because:
1) it simplifies the code (esp. the locking), and
2) serial_core needs such a hook anyway, so have it ready.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Finally, the mxser_close() code in is mostly identical to
tty_port_close(), so replace the code by a single call to the function.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I fail to see the point of calling mxser_flush_buffer() from
mxser_close():
1) The SW xmit buffer is freed in mxser_shutdown_port() right after the
call to mxser_flush_buffer(). And all 'cnt', 'head', and 'tail' are
properly initialized to 0 in mxser_activate().
2) The HW buffer is flushed in mxser_shutdown_port() via
mxser_disable_and_clear_FIFO() too.
So the effect of doing it by mxser_flush_buffer() in mxser_close() is
none. Hence remove it, so that when we use tty_port_close() later, the
code is 1:1 identical.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_stop_rx() should be called from mxser_shutdown_port() for several
reasons:
1) info->slock is held while manipulating IER (as on other places),
2) hangup now stops rx too,
3) mxser_close() will use tty_port_close() and there is no place except
tty_port_operations::shutdown() where this can be done,
4) this is the same sequence as serial_core does. So we can map this
code 1:1 when switching the driver to it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noone sets tty->driver_data to NULL in the driver, so there is no point
to check that in mxser_close(). Remove the check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xmit_buf is supposed to exist in all these functions. I.e. from
tty_port_operations::activate() to ::shutdown(). So remove these checks.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port->icount.tx is handled in a too complicated manner. Instead of
remembering the original count and subtracting the new one from it,
simply increase tx for each character in the loop. No need for cnt
variable then.
Change also the "X = X & Y" assignment to simpler "X &= Y".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MSR read is currently performed on both places where
mxser_check_modem_status() is called. So move it there to avoid code
duplication.
Rename the variable to msr while we move it, to actually see what
"status" we are testing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The others are superfluous with tty refcounting in place now. And they
are racy in fact:
* tty_port_initialized() reports false for a small moment after
interrupts are enabled.
* closing is 1 while the port is still alive.
The queues are flushed later during close anyway. So there is no need
for this special handling. Actually, the ISR should not flush the
queues. It should behave as every other driver, just queue the chars
into tty buffer and go on. But this will be changed later. There is
still a lot code depending on having tty in ISR (and not only tty_port).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it is the only thing it does now. This is one of the future
serial_core hooks.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_close() behaves like this:
-> tty_port_close_start()
-> tty_wait_until_sent()
-> mxser_wait_until_sent()
-> mxser_close_port
-> wait for TEMT
So it is already waited for TEMT through mxser_wait_until_sent() and
there is another round of waiting in mxser_close_port(). The latter one
is superfluous as nothing could be filled into the output FIFO. Remove
the call.
This helps unification among drivers (so that all behave the same) and
future use of tty_port_close().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On RZ/G2L SoC we need to explicitly deassert the reset line
for the device to work, use this opportunity to deassert/assert
reset line in sh-sci driver.
This patch adds support to read the "resets" property (if available)
from DT and perform deassert/assert when required.
Also, propagate the error to the caller of sci_parse_dt() instead of
returning NULL in case of failure.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two consequent checks of uport != NULL in
uart_port_shutdown(). Join these two under a single block.
De-multiline the comments when shuffling with them anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118071911.12059-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both do_SAK_work() and vc_SAK() provide a valid tty to __do_SAK(), so
remove the check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118071911.12059-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the TTY_SOFT_SAK part. It is never defined, so this is only
confusing.
It was actually never defined since its introduction in
0.99.14g.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118071911.12059-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 89d4f98ae9 ("ARM: remove zte zx platform") missed to remove some
definitions for this platform's debug and serial, e.g., code dependent on
the config DEBUG_ZTE_ZX.
Fortunately, ./scripts/checkkconfigsymbols.py detects this and warns:
DEBUG_ZTE_ZX
Referencing files: arch/arm/include/debug/pl01x.S
Further review by Arnd Bergmann identified even more dead code in the
amba serial driver.
Remove all this left-over from the zte zx platform.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211102063810.932-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
coccicheck complains about the use of snprintf() in sysfs show
functions:
WARNING use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jing Yao <yao.jing2@zte.com.cn>
Link: https://lore.kernel.org/r/20211104114754.30983-1-yao.jing2@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit b4b844930f ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation uses 0 as lower limit for the baud rate
tolerance for tegra20 and tegra30 chips which causes isses on UART
initialization as soon as baud rate clock is lower than required even
when within the standard UART tolerance of +/- 4%.
This fix aligns the implementation with the initial commit description
of +/- 4% tolerance for tegra chips other than tegra186 and
tegra194.
Fixes: d781ec21ba ("serial: tegra: report clk rate errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Patrik John <patrik.john@u-blox.com>
Link: https://lore.kernel.org/r/sig.19614244f8.20211123132737.88341-1-patrik.john@u-blox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LITEX symbol is neither a build or runtime dependency for the
liteuart serial driver.
LITEX is selected by the "LiteX SoC Controller" driver, which does a
probe-time register-access sanity check and panics if the SoC has not
been configured correctly. That driver's Kconfig entry asserts that any
LiteX driver using the LiteX register accessors should depend on LITEX,
but currently only the serial driver complies.
Relax this LITEX "dependency" in order to make it easier to compile test
the driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to release the allocated minor number before returning on
probe errors.
Fixes: 1da81e5562 ("drivers/tty/serial: add LiteUART driver")
Cc: stable@vger.kernel.org # 5.11
Cc: Filip Kokosinski <fkokosinski@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deregister the port when unbinding the driver to prevent it from being
used after releasing the driver data and leaking memory allocated by
serial core.
Fixes: 1da81e5562 ("drivers/tty/serial: add LiteUART driver")
Cc: stable@vger.kernel.org # 5.11
Cc: Filip Kokosinski <fkokosinski@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drvdata has to be set in _probe() - otherwise platform_get_drvdata()
causes null pointer dereference BUG in _remove().
Fixes: 1da81e5562 ("drivers/tty/serial: add LiteUART driver")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ilia Sergachev <silia@ethz.ch>
Link: https://lore.kernel.org/r/20211115224944.23f8c12b@dtkw
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.
This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:
* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received
This repeats then for each group of 4 input values.
This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.
RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.
Fixes: 9969394501 ("tty: serial: msm: Add RX DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000
Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.
Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 761ed4a945 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e4 ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145a ("tty/serial: do not free
trasnmit buffer page under port lock")).
Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: stable@vger.kernel.org # 4.9
Cc: Rob Herring <robh@kernel.org>
Reported-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Xen pv console driver is not essential for boot. Set the respective
flag.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20211022064800.14978-4-jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPczQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykWbwCfaIScbUoCUx+h/uP93nKKD8B3KgYAoMvFuhhD
D/fTLggs12x5NsvLBgtZ
=rq0R
-----END PGP SIGNATURE-----
Merge tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (86 commits)
tty: Fix extra "not" in TTY_DRIVER_REAL_RAW description
serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE
tty: rpmsg: Define tty name via constant string literal
tty: rpmsg: Add pr_fmt() to prefix messages
tty: rpmsg: Use dev_err_probe() in ->probe()
tty: rpmsg: Unify variable used to keep an error code
tty: rpmsg: Assign returned id to a local variable
serial: stm32: push DMA RX data before suspending
serial: stm32: terminate / restart DMA transfer at suspend / resume
serial: stm32: rework RX dma initialization and release
serial: 8250_pci: Remove empty stub pci_quatech_exit()
serial: 8250_pci: Replace custom pci_match_id() implementation
serial: xilinx_uartps: Fix race condition causing stuck TX
serial: sunzilog: Mark sunzilog_putchar() __maybe_unused
Revert "tty: hvc: pass DMA capable memory to put_chars()"
Revert "virtio-console: remove unnecessary kmemdup()"
serial: 8250_pci: Replace dev_*() by pci_*() macros
serial: 8250_pci: Get rid of redundant 'else' keyword
serial: 8250_pci: Refactor the loop in pci_ite887x_init()
tty: add rpmsg driver
...
If CONFIG_CONSOLE_POLL=y, and CONFIG_SERIAL_CPM=m (hence
CONFIG_SERIAL_CPM_CONSOLE=n):
drivers/tty/serial/cpm_uart/cpm_uart_core.c:1109:12: warning: ‘udbg_cpm_getc’ defined but not used [-Wunused-function]
1109 | static int udbg_cpm_getc(void)
| ^~~~~~~~~~~~~
drivers/tty/serial/cpm_uart/cpm_uart_core.c:1095:13: warning: ‘udbg_cpm_putc’ defined but not used [-Wunused-function]
1095 | static void udbg_cpm_putc(char c)
| ^~~~~~~~~~~~~
Fix this by making the udbg definitions depend on
CONFIG_SERIAL_CPM_CONSOLE, in addition to CONFIG_CONSOLE_POLL.
Fixes: a60526097f ("tty: serial: cpm_uart: Add udbg support for enabling xmon")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211027075326.3270785-1-geert@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver uses already twice the same string literal.
Define it in one place, so every user will have this
name consistent.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211025135148.53944-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of putting garbage in the data structure, assign allocated id
or an error code to a temporary variable. This makes code cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211025135148.53944-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Data may be stored in DMA RX buffer, when suspending. The data needs
to be pushed to the upper layer. We can't rely on the timeout IRQ (RTOR)
that can't be triggered into low power state. So safely clear DMA request
(DMAR), force the DMA reception routines to push RX buffer content, before
disabling RX DMA. This way, handover to pio mode is safe.
Only call tty_flip_buffer_push() when there is RX data to handle.
Move the locking outside of stm32_usart_receive_chars() to prevent a race
condition, when disabling DMA request upon suspend / pm_runtime_suspend.
Data may be received under IRQ and pushed before
stm32_usart_receive_chars() has pushed older data from DMA rx_buf upon
suspend.
The sequence in suspend routine needs proper locking to avoid this.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA prevents the system to suspend when an UART RX wake-up source is
using DMA. DMA can't suspend while DMA channels are still active.
Terminate DMA transfer at suspend, and restart a new DMA transfer at
resume. Create stm32_usart_start_rx_dma_cyclic function to factorize
dma RX initialization. Move RX DMA code related to wakeup into
stm32_usart_serial_en_wakeup() routine to ease further improvements
on wakeup from low power modes.
Don't enable/disable wakeup on uninitialized port.
There may be data residue in the RX FIFO while suspending. Flush it at
suspend time. Receiver timeout interrupt won't trigger later in low power
mode, so call stm32_usart_receive_chars() in case there's data to handle.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RX DMA channel is kept active forever (from the probe). That prevents
going to low power mode when it is used. This change moves the
DMA configuration and enabling procedures to startup routine to allow
transition to low power mode.
The DMA disabling procedure is implemented in stop_rx routine as this
ops has to stop characters reception, and DMA transation in shutdown.
Clean useless dma_async_tx_descriptor initialization to NULL value.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid
any previous TXEVENT event asserting the UART interrupt. This clear
operation is done immediately after filling the TX FIFO.
However, if the bytes inserted by cdns_uart_handle_tx() are consumed by
the UART before the TXEMPTY is cleared, the clear operation eats the new
TXEMPTY event as well, causing cdns_uart_isr() to never receive the
TXEMPTY event. If there are bytes still queued in circbuf, TX will get
stuck as they will never get transferred to FIFO (unless new bytes are
queued to circbuf in which case .start_tx() is called again).
While the racy missed TXEMPTY occurs fairly often with short data
sequences (e.g. write 1 byte), in those cases circbuf is usually empty
so no action on TXEMPTY would have been needed anyway. On the other
hand, longer data sequences make the race much more unlikely as UART
takes longer to consume the TX FIFO. Therefore it is rare for this race
to cause visible issues in general.
Fix the race by clearing the TXEMPTY bit in ISR *before* filling the
FIFO.
The TXEMPTY bit in ISR will only get asserted at the exact moment the
TX FIFO *becomes* empty, so clearing the bit before filling FIFO does
not cause an extra immediate assertion even if the FIFO is initially
empty.
This is hard to reproduce directly on a normal system, but inserting
e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud,
and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50"
reliably reproduces the issue on my ZynqMP test system unless this fix
is applied.
Fixes: 85baf542d5 ("tty: xuartps: support 64 byte FIFO size")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/r/20211026102741.2910441-1-anssi.hannula@bitwise.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONSOLE_POLL=n, CONFIG_SERIAL_SUNZILOG_CONSOLE=n, and CONFIG_SERIO=m:
drivers/tty/serial/sunzilog.c:1128:13: error: ‘sunzilog_putchar’ defined but not used [-Werror=unused-function]
1128 | static void sunzilog_putchar(struct uart_port *port, int ch)
| ^~~~~~~~~~~~~~~~
Fix this by marking sunzilog_putchar() __maybe_unused.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211026080426.2444756-1-geert@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0986d7bc55.
It still has some issues and needs to be dropped at this point in time.
Link: https://lore.kernel.org/r/208f7a41-a9fa-630c-cb44-c37c503f3a72@kernel.org
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Cc: Xianting Tian <xianting.tian@linux.alibaba.com>
Cc: Shile Zhang <shile.zhang@linux.alibaba.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'else' keyword is not needed when previous conditional branch returns
to the upper layer. Get rid of redundant 'else' keyword in such cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loop can be refactored by using ARRAY_SIZE() instead of NULL terminator.
This reduces code base and makes it easier to read and understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver exposes a standard TTY interface on top of the rpmsg
framework through a rpmsg service.
This driver supports multi-instances, offering a /dev/ttyRPMSGx entry
per rpmsg endpoint.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20211015094701.5732-3-arnaud.pouliquen@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was updating the port uartclk before setting the new rate in
an attempt to avoid having the clock notifier redundantly update the
divisors.
The set_termios() callback is however called under the termios semaphore
and tty-port mutex so the worker scheduled by the clock notifier will
block in serial8250_update_uartclk() until the uartclk and divisors have
been updated anyway.
Drop the unnecessary swaps and incorrect comment and simply update the
uartclk field if the clock-rate change was successful.
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename a couple of oddly named labels that are used to unlock before
returning after what they do (rather than after the context they are
used in) to improve readability.
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
added a hack to support SoCs where the UART reference clock can
change behind the back of the driver but failed to add the proper
locking.
First, make sure to take a reference to the tty struct to avoid
dereferencing a NULL pointer if the clock change races with a hangup.
Second, the termios semaphore must be held during the update to prevent
a racing termios change.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Fixes: c8dff3aa82 ("serial: 8250: Skip uninitialized TTY port baud rate update")
Cc: stable@vger.kernel.org # 5.9
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable DMA request line (if enabled) to switch in PIO mode in throttle
ops, so the RX data gets queues into the FIFO. The hardware flow control
is triggered when the RX FIFO is full.
Switch back to DMA mode (re-enable DMA request line) in unthrottle ops.
Hardware flow control is stopped when FIFO is not full anymore.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211020150332.10214-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reworks RX support over DMA to improve reliability:
- change dma buffer cyclic configuration by using 2 periods. DMA buffer
data are handled by a flip-flop between the 2 periods in order to avoid
risk of data loss/corruption
- change the size of dma buffer to 4096 to limit overruns
- add rx errors management (breaks, parity, framing and overrun).
When an error occurs on the uart line, the dma request line is masked at
HW level. The SW must 1st clear DMAR (dma request line enable), to
handle the error, then re-enable DMAR to recover. So, any correct data
is taken from the DMA buffer, before handling the error itself. Then
errors are handled from RDR/ISR/FIFO (e.g. in PIO mode). Last, DMA
reception is resumed.
- add a condition on DMA request line in DMA RX routines in order to
switch to PIO mode when no DMA request line is disabled, even if the DMA
channel is still enabled.
When the UART is wakeup source and is configured to use DMA for RX, any
incoming data that wakes up the system isn't correctly received.
At data reception, the irq_handler handles the WUF irq, and then the
data reception over DMA.
As the DMA transfer has been terminated at suspend, and will be restored
by resume callback (which has no yet been called by system), the data
can't be received.
The wake-up data has to be handled in PIO mode while suspend callback
has not been called.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211020150332.10214-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Re-introduce an irq flag condition in usart_receive_chars.
This condition has been deleted by commit 75f4e830fa ("serial: do not
restore interrupt state in sysrq helper").
This code was present to handle threaded case, and has been removed
because it is no more needed in this case. Nevertheless an irq safe lock
is still needed in some cases, when DMA should be stopped to receive errors
or breaks in PIO mode.
This patch is a precursor to the complete rework or stm32 serial driver
DMA implementation.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211020150332.10214-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As well known, hvc backend can register its opertions to hvc backend.
the operations contain put_chars(), get_chars() and so on.
Some hvc backend may do dma in its operations. eg, put_chars() of
virtio-console. But in the code of hvc framework, it may pass DMA
incapable memory to put_chars() under a specific configuration, which
is explained in commit c4baad5029(virtio-console: avoid DMA from stack):
1, c[] is on stack,
hvc_console_print():
char c[N_OUTBUF] __ALIGNED__;
cons_ops[index]->put_chars(vtermnos[index], c, i);
2, ch is on stack,
static void hvc_poll_put_char(,,char ch)
{
struct tty_struct *tty = driver->ttys[0];
struct hvc_struct *hp = tty->driver_data;
int n;
do {
n = hp->ops->put_chars(hp->vtermno, &ch, 1);
} while (n <= 0);
}
Commit c4baad5029 is just the fix to avoid DMA from stack memory, which
is passed to virtio-console by hvc framework in above code. But I think
the fix is aggressive, it directly uses kmemdup() to alloc new buffer
from kmalloc area and do memcpy no matter the memory is in kmalloc area
or not. But most importantly, it should better be fixed in the hvc
framework, by changing it to never pass stack memory to the put_chars()
function in the first place. Otherwise, we still face the same issue if
a new hvc backend using dma added in the furture.
In this patch, add 'char cons_outbuf[]' as part of 'struct hvc_struct',
so hp->cons_outbuf is no longer the stack memory, we can use it in above
cases safely. We also add lock to protect cons_outbuf instead of using
the global lock of hvc.
Introduce another array(cons_hvcs[]) for hvc pointers next to the
cons_ops[] and vtermnos[] arrays. With the array, we can easily find
hvc's cons_outbuf and its lock.
With the patch, we can revert the fix c4baad5029.
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Signed-off-by: Shile Zhang <shile.zhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20211015024658.1353987-3-xianting.tian@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use L1_CACHE_BYTES as the dma alignment size, use 'sizeof(long)' as
dma alignment is wrong.
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Signed-off-by: Shile Zhang <shile.zhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20211015024658.1353987-2-xianting.tian@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During console setup imx_uart_console_setup() enables clocks, but they
are never disabled when the console is unregistered, this leads to
clk_prepare_enable() being called multiple times without a matching
clk_disable_unprepare() in case of console unregister.
Ensure that clock enable/disable are balanced adding
clk_disable_unprepare() in the console exit callback.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20211020192643.476895-3-francesco.dolcini@toradex.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently show_workqueue_state shows the state of all workqueues and of
all worker pools. In certain cases we may need to dump state of only a
specific workqueue or worker pool. For example in destroy_workqueue we
only need to show state of the workqueue which is getting destroyed.
So rename show_workqueue_state to show_all_workqueues(to signify it
dumps state of all busy workqueues) and divide it into more granular
functions (show_one_workqueue and show_one_worker_pool), that would show
states of individual workqueues and worker pools and can be used in
cases such as the one mentioned above.
Also, as mentioned earlier, make destroy_workqueue dump data pertaining
to only the workqueue that is being destroyed and make user(s) of
earlier interface(show_workqueue_state), use new interface
(show_all_workqueues).
Signed-off-by: Imran Khan <imran.f.khan@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When running ltp testcase(ltp/testcases/kernel/pty/pty04.c) with arm64, there is a soft lockup,
which look like this one:
Workqueue: events_unbound flush_to_ldisc
Call trace:
dump_backtrace+0x0/0x1ec
show_stack+0x24/0x30
dump_stack+0xd0/0x128
panic+0x15c/0x374
watchdog_timer_fn+0x2b8/0x304
__run_hrtimer+0x88/0x2c0
__hrtimer_run_queues+0xa4/0x120
hrtimer_interrupt+0xfc/0x270
arch_timer_handler_phys+0x40/0x50
handle_percpu_devid_irq+0x94/0x220
__handle_domain_irq+0x88/0xf0
gic_handle_irq+0x84/0xfc
el1_irq+0xc8/0x180
slip_unesc+0x80/0x214 [slip]
tty_ldisc_receive_buf+0x64/0x80
tty_port_default_receive_buf+0x50/0x90
flush_to_ldisc+0xbc/0x110
process_one_work+0x1d4/0x4b0
worker_thread+0x180/0x430
kthread+0x11c/0x120
In the testcase pty04, The first process call the write syscall to send
data to the pty master. At the same time, the workqueue will do the
flush_to_ldisc to pop data in a loop until there is no more data left.
When the sender and workqueue running in different core, the sender sends
data fastly in full time which will result in workqueue doing work in loop
for a long time and occuring softlockup in flush_to_ldisc with kernel
configured without preempt. So I add need_resched check and cond_resched
in the flush_to_ldisc loop to avoid it.
Signed-off-by: Guanghui Feng <guanghuifeng@linux.alibaba.com>
Link: https://lore.kernel.org/r/1633961304-24759-1-git-send-email-guanghuifeng@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a single 8250 Kconfig fix for 5.15-rc6 that resolves a
regression that showed up in 5.15-rc1. It has been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYWv0Mg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykeJgCfT8mYR7xo2iTzFRqfvarzH1hvIIgAn3HGUFNf
K3cV5OyOc9lZnGKYhYE6
=SMH1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"Here is a single 8250 Kconfig fix for 5.15-rc6 that resolves a
regression that showed up in 5.15-rc1. It has been in linux-next for a
while with no reported issues"
* tag 'tty-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250: allow disabling of Freescale 16550 compile test
Up to now sc16is7xx_remove() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211012153945.2651412-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Up to now max310x_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211012153945.2651412-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a call to the custom ->set_termios() which has implementation about
changing the state of RTS and CTS.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005133026.21488-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the code currently used in dw8250_set_termios(), byt_set_termios()
may be reused by other methods in the future. Extract it to a common helper
function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005133026.21488-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In couple of places we may re-use temporary variable instead of
dereferencing it. No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134529.23256-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI_PTR() is more harmful than helpful. For example, in this case
if CONFIG_ACPI=n, the ID table left unused which is not what we want.
Instead of adding ifdeffery here and there, drop ACPI_PTR().
Fixes: 6a7320c466 ("serial: 8250_dw: Add ACPI 5.0 support")
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134516.23218-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having "_USI" suffix in EXYNOS_COMMON_SERIAL_DRV_DATA_USI() macro is
confusing. Rename it to just EXYNOS_COMMON_SERIAL_DRV_DATA() and provide
USI registers availability for all Exynos variants instead. While at it,
also convert .has_usi field type to bool, so its usage is more obvious.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211005095800.2165-1-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYWBSIwAKCRCAXGG7T9hj
vrXxAP9na1EqRJ+SpWyvxHY1jMaIrbg1bgnOc+GsnWxU5liW5AEA4h1HjHtVtrzL
3vweIS6u2fanrWlYML/daQ3r6EuLPQc=
=iXsP
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.15b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fix two minor issues in the Xen privcmd driver plus a cleanup patch
for that driver
- fix multiple issues related to running as PVH guest and some related
earlyprintk fixes for other Xen guest types
- fix an issue introduced in 5.15 the Xen balloon driver
* tag 'for-linus-5.15b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: fix cancelled balloon action
xen/x86: adjust data placement
x86/PVH: adjust function/data placement
xen/x86: hook up xen_banner() also for PVH
xen/x86: generalize preferred console model from PV to PVH Dom0
xen/x86: make "earlyprintk=xen" work for HVM/PVH DomU
xen/x86: allow "earlyprintk=xen" to work for PV Dom0
xen/x86: make "earlyprintk=xen" work better for PVH Dom0
xen/x86: allow PVH Dom0 without XEN_PV=y
xen/x86: prevent PVH type from getting clobbered
xen/privcmd: drop "pages" parameter from xen_remap_pfn()
xen/privcmd: fix error handling in mmap-resource processing
xen/privcmd: replace kcalloc() by kvcalloc() when allocating empty pages
This reverts commit 32262e2e42.
The commit in question claims to determine the inverse of
serial8250_get_divisor() but failed to notice that some drivers override
the default implementation using a get_divisor() callback.
This means that the computed line-speed values can be completely wrong
and results in regular TCSETS requests failing (the incorrect values
would also be passed to any overridden set_divisor() callback).
Similarly, it also failed to honour the old (deprecated) ASYNC_SPD_FLAGS
and would break applications relying on those when re-encoding the
actual line speed.
There are also at least two quirks, UART_BUG_QUOT and an OMAP1510
workaround, which were happily ignored and that are now broken.
Finally, even if the offending commit were to be implemented correctly,
this is a new feature and not something which should be backported to
stable.
Cc: Pali Rohár <pali@kernel.org>
Fixes: 32262e2e42 ("serial: 8250: Fix reporting real baudrate value in c_ospeed field")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211007133146.28949-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SERIAL_8250_FSL option is used to enable a workaround for a
break-detection erratum for Freescale 16550 UARTs in the 8250 driver and
is currently also used to enable support for ACPI enumeration.
It is enabled on PPC, ARM and ARM64 whenever 8250 console support is
enabled (since the quirk is needed for sysrq handling).
Commit b1442c55ce ("serial: 8250: extend compile-test coverage")
enabled compile testing of the code in question but did not provide a
means to disable the option when COMPILE_TEST is enabled.
Add a conditional input prompt instead so that SERIAL_8250_FSL is no
longer enabled by default when compile testing while continuing to
always enable the quirk for platforms that may need it.
Fixes: b1442c55ce ("serial: 8250: extend compile-test coverage")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210924141232.4419-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases it is not possible to set exact baudrate value to hardware.
So fix reporting real baudrate value which was set to hardware via c_ospeed
termios field. It can be retrieved by ioctl(TCGETS2) from userspace.
Real baudrate value is calculated from chosen hardware divisor and base
clock. It is implemented in a new function serial8250_compute_baud_rate()
which is inverse of serial8250_get_divisor() function.
With this change is fixed also UART timeout value (it is updated via
uart_update_timeout() function), which is calculated from the now fixed
baudrate value too.
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210927093704.19768-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit edc6afc549 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.
In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.
Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.
If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.
This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.
Fixes: edc6afc549 ("[PATCH] tty: switch to ktermios and new framework")
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function tty_termios_input_baud_rate() checks IBSHIFT & CBAUD against B0
constant to determinate if input speed equals to output speed. So do same
B0 check also in tty_termios_encode_baud_rate() function to make these two
functions compatible.
Currently macro B0 is defined to 0 so there is no functional change.
This change just make code more explicit to show that Bnnn constants are
stored in CBAUD.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210927133516.8671-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the assignment of sifive_serial_console_ports[ssp->port.line],
this is a pointer to a struct sifive_serial_port so the assignment
should be a NULL rather than a integer 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210925224726.183360-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We force the FCR contents on many places in the code instead of writing
what was actually set in mxser_change_speed() (by ->activate() or
->set_serial_info()).
So introduce mxser_port::FCR to hold the proper contents and bitwise-OR
the value to what needs to be set on all those locations. That is,
clearing RX and/or TX FIFOs. Those flags are self-clearing, so no need
to set them to mxser_port::FCR.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_FCR register is write-only. When reading it, one gets contents
of (read-only) UART_IIR instead as they are shared. This mistake was
performed in mxser_flush_buffer() to clear FIFOs.
Actually FCR handling throughout the driver is completely broken. On
many places, it respects neither mu860 settings, nor FIFO (16450 vs
16550) setting. This patch doesn't help to fix this, it actually does
the same. We will introduce a mxser_port::FCR in the next patch to fix
this issue.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code is used on two places, make a helper for disabling and
clearing FIFOs. And demangle the too complicated 'if' by using a local
variable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provided FIFO is always enabled for MUST chips, move its FCR setting out
of PORT_8250/PORT_16450 special case in mxser_change_speed(). Now, we
can pre-set fcr to zero and invert the condition of the 'if'.
This makes the code more readable (no functional change intended).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's used only as a yes-no variable, so make it a bool and switch the
set values appropriately.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_receive_chars_old() is used whenever MOXA_MUST_LSR_RERR is set in
status no matter the HW ID (the last 'if'). So there is no need for
another check of MOXA_MUST_LSR_RERR _with_ hwid == MOXA_MUST_MU860_HWID
(the third 'if'). Hence remove this subcase. That allows us to check
status on a single line with both UART_LSR_BRK_ERROR_BITS (from the
second 'if') and MOXA_MUST_LSR_RERR (the last 'if').
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a user tries to set a too high rate, it fails due to check in
mxser_set_baud(). But the high rate remains set in termios, so the user
might think everything went smooth. Restore the baud rate from the
old_termios if this happens, so that user knows nothing was changed in
fact.
It used to behave the correct way many years ago, but somehow the
restoration vanished with commit 1c45607ad3 (Char: mxser, remove it)
-- the commit removed mxser's older clone.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently have gsmld_output() ignore the return value from device
write. This means we will lose packets if device write returns 0 or
an error.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210930060624.46523-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two lines need to be indented one more tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211004104343.GF25015@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xenboot_write_console() is dealing with these quite fine so I don't see
why xenboot_console_setup() would return -ENOENT in this case.
Adjust documentation accordingly.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/3d212583-700e-8b2d-727a-845ef33ac265@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
The xen_hvm_early_write() path better wouldn't be taken in this case;
while port 0xE9 can be used, the hypercall path is quite a bit more
efficient. Put that first, as it may also work for DomU-s (see also
xen_raw_console_write()).
While there also bail from the function when the first
domU_write_console() failed - later ones aren't going to succeed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/4fd89dcb-cfc5-c740-2e94-bb271e432d3e@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
After the previous patch, there are no users of 'file' in
n_tty_ioctl_helper. So remove it also from there.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only user of 'file' parameter in tty_mode_ioctl is a BUG_ON check.
Provided it never crashed for anyone, it's an overkill to pass the
parameter to tty_mode_ioctl only for this check.
If we wanted to check 'file' there, we should handle it in more graceful
way anyway. Not by a BUG == crash.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last user was apparently removed by commit a352def21a (tty: Ldisc
revamp) in 2008. So remove the field completely, the only setter
(n_tty_inherit_ops) and also its only possible value
(LDISC_FLAG_DEFINED).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially, tty_ldisc_release() was exported for speakup (spk_tty) while
in staging. Later, the call to this function was removed as it was bogus
anyway.
Remove the export now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Emma Mobile integrated serial port hardware is only present on Emma
Mobile SoCs. Hence add a dependency on ARCH_RENESAS, to prevent asking
the user about this driver when configuring a kernel without Renesas
ARM32 SoC support.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7b5a4bbf2f47b2c4c127817e8b1524a650795d97.1631710085.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially, tty_ldisc_release() was exported for speakup (spk_tty) while
in staging. Later, the call to this function was removed as it was bogus
anyway.
Remove the export now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for existence of a separate header for Moxa's Intellio
cards. Merge it into moxa.c to clean up the tty dir a bit.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914090823.17206-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'set_signals()' in synclink_gt.c conflicts with an exported symbol
in arch/um/, so change set_signals() to set_gtsignals(). Keep
the function names similar by also changing get_signals() to
get_gtsignals().
../drivers/tty/synclink_gt.c:442:13: error: conflicting types for ‘set_signals’
static void set_signals(struct slgt_info *info);
^~~~~~~~~~~
In file included from ../include/linux/irqflags.h:16:0,
from ../include/linux/spinlock.h:58,
from ../include/linux/mm_types.h:9,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/tty/synclink_gt.c:46:
../arch/um/include/asm/irqflags.h:6:5: note: previous declaration of ‘set_signals’ was here
int set_signals(int enable);
^~~~~~~~~~~
Fixes: 705b6c7b34 ("[PATCH] new driver synclink_gt")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210902003806.17054-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As requester,because n_gsm has no uevent report for application,the
application can't know dlci connect or disconnect.
The application will control every dlcl dev by uevent,when application
receive gsmtty0 dev remove uevent,it will close mux function,and change to
normal mode.
Example:
Before modify:
gsmld receive DLC0 DISC,no event report to application
gsmld receive DLC1 SABM,no event report to application
gsmld receive DLC1 DISC,no event report to application
After modify:
Receive DLC0 DISC,report "/devices/virtual/tty/gsmtty0" remove uevent
Receive DLC1 SABM,report "/devices/virtual/tty/gsmtty1" add uevent
Receive DLC1 DISC,report "/devices/virtual/tty/gsmtty1" remove uevent
Signed-off-by: Zhenguo Zhao <Zhenguo.Zhao1@unisoc.com>
Link: https://lore.kernel.org/r/1629461872-26965-7-git-send-email-zhenguo6858@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When n_gsm config "initiator=0",when gsmld config ,as requester ,it
doesn't need to send CLD frame data or SABM frame.
Example,when tty dev receive "AT+CMUX=0",it will change ldisc
n_tty to n_gsm,during config requester,gsmld output "7e 01 ef c3 aa 7e",
initiator maybe not want to receive the frame data.
[ 154.666457] c1 Q> 0) R: UIH(F)
[ 154.669514] c1 C3
[ 154.671519] c1 gsmld_output: 00000000: 7e 01 ef c3 aa 7e
[ 155.014874] c1 Q> 0) R: UIH(F)
[ 155.018000] c1 C3
[ 155.020046] c1 gsmld_output: 00000000: 7e 01 ef c3 aa 7e
[ 155.364425] c1 Q> 0) R: UIH(F)
[ 155.367546] c1 C3
[ 155.369597] c1 gsmld_output: 00000000: 7e 01 ef c3 aa 7e
Signed-off-by: Zhenguo Zhao <Zhenguo.Zhao1@unisoc.com>
Link: https://lore.kernel.org/r/1629461872-26965-5-git-send-email-zhenguo6858@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver's tx_empty callback should signal when the transmit shift register
is empty. So when the last character has been sent.
STAT_TX_FIFO_EMP bit signals only that HW transmit FIFO is empty, which
happens when the last byte is loaded into transmit shift register.
STAT_TX_EMP bit signals when the both HW transmit FIFO and transmit shift
register are empty.
So replace STAT_TX_FIFO_EMP check by STAT_TX_EMP in mvebu_uart_tx_empty()
callback function.
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210911132017.25505-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b67e830d38 ("serial: 8250: 8250_omap: Fix possible interrupt
storm on K3 SoCs") introduced fixup including a register read to
RX_LVL, however, we should be using word offset than byte offset
since our registers are on 4 byte boundary (port.regshift = 2) for
8250_omap.
Fixes: b67e830d38 ("serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs")
Cc: stable <stable@vger.kernel.org>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210903050550.29050-1-nm@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device does not support changing baud, parity, data bits, stop
bits, or detecting breaks. Disable "changing" these settings to prevent
their termios from diverging from the actual state of the uart.
In order to determine the correct parameters to enforce, we read the
various new devicetree parameters to discover how the uart was
configured when it was synthesized. The defaults match
ulite_console_setup. xlnx,use-parity, xlnx,odd-parity, and
xlnx,data-bits are optional since there were in-tree users (and
presumably out-of-tree users) who did not set them.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210826192154.3202269-5-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + size * count" in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210905155728.11147-1-len.baker@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a kernel crash when a signal is delivered to bad userspace stack
- Fix fall-through warnings in math-emu code
- Increase size of gcc stack frame check
- Switch coding from 'pci_' to 'dma_' API
- Make struct parisc_driver::remove() return void
- Some parisc related Makefile changes
- Minor cleanups, e.g. change to octal permissions, fix macro collisions,
fix PMD_ORDER collision, replace spaces with tabs
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCYTELwQAKCRD3ErUQojoP
Xy/uAQChkDVD15kBvj0PUt4hDpGq7ryfAsEfMnxlV2k4Ue6SKAEA3Smfd242lpPF
f89NNo6Y/ZhO+aWKfOLerXLfM6sB2QQ=
=cxvN
-----END PGP SIGNATURE-----
Merge tag 'for-5.15/parisc' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture updates from Helge Deller:
- Fix a kernel crash when a signal is delivered to bad userspace stack
- Fix fall-through warnings in math-emu code
- Increase size of gcc stack frame check
- Switch coding from 'pci_' to 'dma_' API
- Make struct parisc_driver::remove() return void
- Some parisc related Makefile changes
- Minor cleanups, e.g. change to octal permissions, fix macro
collisions, fix PMD_ORDER collision, replace spaces with tabs
* tag 'for-5.15/parisc' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: math-emu: Fix fall-through warnings
parisc: fix crash with signals and alloca
parisc: Fix compile failure when building 64-bit kernel natively
parisc: ccio-dma.c: Added tab instead of spaces
parisc/parport_gsc: switch from 'pci_' to 'dma_' API
parisc: move core-y in arch/parisc/Makefile to arch/parisc/Kbuild
parisc: switch from 'pci_' to 'dma_' API
parisc: Make struct parisc_driver::remove() return void
parisc: remove unused arch/parisc/boot/install.sh and its phony target
parisc: Rename PMD_ORDER to PMD_TABLE_ORDER
parisc: math-emu: Avoid "fmt" macro collision
parisc: Increase size of gcc stack frame check
parisc: Replace symbolic permissions with octal permissions
Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more cleanups
on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9/lg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylZNwCggKViEViSGqJFIafAZZjmI3Nt6tUAoMkRlhcd
n1MS3snS0Sq+7BdJs37M
=GyxP
-----END PGP SIGNATURE-----
Merge tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more
cleanups on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (83 commits)
tty: serial: uartlite: Use read_poll_timeout for a polling loop
tty: serial: uartlite: Use constants in early_uartlite_putc
tty: Fix data race between tiocsti() and flush_to_ldisc()
serial: vt8500: Use of_device_get_match_data
serial: tegra: Use of_device_get_match_data
serial: 8250_ingenic: Use of_device_get_match_data
tty: serial: linflexuart: Remove redundant check to simplify the code
tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
tty: serial: fsl_lpuart: enable two stop bits for lpuart32
tty: serial: fsl_lpuart: fix the wrong mapbase value
mxser: use semi-colons instead of commas
tty: moxa: use semi-colons instead of commas
tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
tty: replace in_irq() with in_hardirq()
serial: sh-sci: fix break handling for sysrq
serial: stm32: use devm_platform_get_and_ioremap_resource()
serial: stm32: use the defined variable to simplify code
Revert "arm pl011 serial: support multi-irq request"
tty: serial: samsung: Add Exynos850 SoC data
tty: serial: samsung: Fix driver data macros style
...
Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did the
following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
The latter one will cause a tiny merge issue with your tree, as there
was a last-minute fix for this in 5.14 in your tree, but the fixup
should be "obvious". If you want me to provide a fixed merge for this,
please let me know.
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs
users at once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+FLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXuACfWECnysDtXNe66DdETCFs1a1RToYAoMokWeU5
s8VFP1NY2BjmxJbkebLL
=8kVu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read
out again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs
in kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by
the router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105)
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=JDGD
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read out
again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs in
kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by the
router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105):
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver"
* tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1715 commits)
net: Add depends on OF_NET for LiteX's LiteETH
ipv6: seg6: remove duplicated include
net: hns3: remove unnecessary spaces
net: hns3: add some required spaces
net: hns3: clean up a type mismatch warning
net: hns3: refine function hns3_set_default_feature()
ipv6: remove duplicated 'net/lwtunnel.h' include
net: w5100: check return value after calling platform_get_resource()
net/mlxbf_gige: Make use of devm_platform_ioremap_resourcexxx()
net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()
net: mdio-ipq4019: Make use of devm_platform_ioremap_resource()
fou: remove sparse errors
ipv4: fix endianness issue in inet_rtm_getroute_build_skb()
octeontx2-af: Set proper errorcode for IPv4 checksum errors
octeontx2-af: Fix static code analyzer reported issues
octeontx2-af: Fix mailbox errors in nix_rss_flowkey_cfg
octeontx2-af: Fix loop in free and unmap counter
af_unix: fix potential NULL deref in unix_dgram_connect()
dpaa2-eth: Replace strlcpy with strscpy
octeontx2-af: Use NDC TX for transmit packet data
...
The Linux console's VT102 implementation already consumes OSC
("Operating System Command") sequences, probably because that's how
palette changes are transmitted.
In addition to OSC, there are three other major clases of ANSI control
strings: APC ("Application Program Command"), PM ("Privacy Message"),
and DCS ("Device Control String"). They are handled similarly to OSC in
terms of termination.
Source: vt100.net
Add three new enumerated states, one for each of these types. All three
are handled the same way right now--they simply consume input until
terminated. I hope to expand upon this firmament in the future. Add
new predicate ansi_control_string(), returning true for any of these
states. Replace explicit checks against ESosc with calls to this
function. Transition to these states appropriately from the escape
initiation (ESesc) state.
This was motivated by the following Notcurses bugs:
https://github.com/dankamongmen/notcurses/issues/2050https://github.com/dankamongmen/notcurses/issues/1828https://github.com/dankamongmen/notcurses/issues/2069
where standard VT sequences are not consumed by the Linux console. It's
not necessary that the Linux console *support* these sequences, but it
ought *consume* these well-specified classes of sequences.
Tested by sending a variety of escape sequences to the console, and
verifying that they still worked, or were now properly consumed.
Verified that the escapes were properly terminated at a generic level.
Verified that the Notcurses tools continued to show expected output on
the Linux console, except now without escape bleedthrough.
Link: https://lore.kernel.org/lkml/YSydL0q8iaUfkphg@schwarzgerat.orthanc/
Signed-off-by: nick black <dankamongmen@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The caller of this function (parisc_driver_remove() in
arch/parisc/kernel/drivers.c) ignores the return value, so better don't
return any value at all to not wake wrong expectations in driver authors.
The only function that could return a non-zero value before was
ipmi_parisc_remove() which returns the return value of
ipmi_si_remove_by_dev(). Make this function return void, too, as for all
other callers the value is ignored, too.
Also fold in a small checkpatch fix for:
WARNING: Unnecessary space before function pointer arguments
+ void (*remove) (struct parisc_device *dev);
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> (for drivers/input)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
read_poll_timeout was recently introduced, and can be used to simplify
our console polling loop. This results in a slight reduction in code.
early_uartlite_putc can't get the same treatment, because it can be
called before udelay is set up.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210826192549.3203071-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the constants defined at the beginning of this file instead of
integer literals when accessing registers. This makes this code easier
to read, and obviates the need for some explanatory comments.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210826194323.3209227-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ops->receive_buf() may be accessed concurrently from these two
functions. If the driver flushes data to the line discipline
receive_buf() method while tiocsti() is waiting for the
ops->receive_buf() to finish its work, the data race will happen.
For example:
tty_ioctl |tty_ldisc_receive_buf
->tioctsi | ->tty_port_default_receive_buf
| ->tty_ldisc_receive_buf
->hci_uart_tty_receive | ->hci_uart_tty_receive
->h4_recv | ->h4_recv
In this case, the h4 receive buffer will be overwritten by the
latecomer, and we will lost the data.
Hence, change tioctsi() function to use the exclusive lock interface
from tty_buffer to avoid the data race.
Reported-by: syzbot+97388eb9d31b997fe1d0@syzkaller.appspotmail.com
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210823000641.2082292-1-phind.uet@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve OF match data, it's better and cleaner to use
'of_device_get_match_data' over 'of_match_device'.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210822032806.3256-4-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve OF match data, it's better and cleaner to use
'of_device_get_match_data' over 'of_match_device'.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210822032806.3256-3-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve OF match data, it's better and cleaner to use
'of_device_get_match_data' over 'of_match_device'.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210822032806.3256-2-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function uart_add_one_port(), it can return zero or non-zero,
so remove redundant check to simplify the code.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210823110754.11232-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do software reset for communication port on imx7ulp and imx8qxp after
the port is registered if the UART controller support the feature.
Do partition reset with LPUART's power on, LPUART registers will
keep the previous status, like on i.MX8QXP platform, which is not
expected action, so need to set the RST bit of GLOBAL register to reset
all uart internal logic and registers.
Currently, only i.MX7ULP and i.MX8QXP LPUART controllers include
global register that support the software reset.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210823091801.17447-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add two stop bits support.
User can run the command to enable two stop bits for test:
stty cstopb -F /dev/ttyLPx
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210823081733.31941-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register offset needs to be applied on mapbase also.
dma_tx/rx_request use the physical address of UARTDATA.
Register offset is currently only applied to membase (the
corresponding virtual addr) but not on mapbase.
Fixes: 24b1e5f0e8 ("tty: serial: lpuart: add imx7ulp support")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Adriana Reus <adriana.reus@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Andy Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20210819021033.32606-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code works, but it's cleaner to use semi-colons at the end of
a statement instead of a comma.
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210825072435.GB13013@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code works but it's cleaner to use a semi-colon to end a statement
instead of a comma.
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210825072405.GA13013@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have a corner case that tx DMA .callback() is coming after
.flush_buffer(), then .callback() should check dma_tx_in_progress
flag and return in directly.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Vipul Kumar <vipul_kumar@mentor.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210817100203.21300-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the obsolete and ambiguos macro in_irq() with new
macro in_hardirq().
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Link: https://lore.kernel.org/r/20210814005033.2381-1-changbin.du@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the defined variable 'dev' to make the code cleaner.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210814124951.30084-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b0819465be which
results in amba_device-specific code being called from
sbsa_uart_startup() and sbsa_uart_shutdown().
Signed-off-by: Qian Cai <quic_qiancai@quicinc.com>
Link: https://lore.kernel.org/r/20210813163135.205-1-quic_qiancai@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial driver data for Exynos850 SoC. This driver data is basically
reusing EXYNOS_COMMON_SERIAL_DRV_DATA, which is common for all Exynos
chips, but also enables USI init, which was added in previous commit:
"tty: serial: samsung: Init USI to keep clocks running".
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210811114827.27322-7-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make checkpatch happy by fixing this error:
ERROR: Macros with complex values should be enclosed in parentheses
Although this change is made to keep macros consistent with consequent
patches (adding driver data for new SoC), it's intentionally added as a
separate patch to ease possible porting efforts in future.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210811114827.27322-6-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART block is a part of USI (Universal Serial Interface) IP-core in
Samsung SoCs since Exynos9810 (e.g. in Exynos850). USI allows one to
enable one of three types of serial interface: UART, SPI or I2C. That's
possible because USI shares almost all internal circuits within each
protocol. USI also provides some additional registers so it's possible
to configure it.
One USI register called USI_OPTION has reset value of 0x0. Because of
this the clock gating behavior is controlled by hardware (HWACG =
Hardware Auto Clock Gating), which simply means the serial won't work
after reset as is. In order to make it work, USI_OPTION[2:1] bits must
be set to 0b01, so that HWACG is controlled manually (by software).
Bits meaning:
- CLKREQ_ON = 1: clock is continuously provided to IP
- CLKSTOP_ON = 0: drive IP_CLKREQ to High (needs to be set along with
CLKREQ_ON = 1)
USI is not present on older chips, like s3c2410, s3c2412, s3c2440,
s3c6400, s5pv210, exynos5433, exynos4210. So the new boolean field
'.has_usi' was added to struct s3c24xx_uart_info. USI registers will be
only actually accessed when '.has_usi' field is set to "1".
This feature is needed for further serial enablement on Exynos850, but
some other new Exynos chips (like Exynos9810) may benefit from this
feature as well.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210811114827.27322-5-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as for I²C Serial Bus resource split and export
serdev_acpi_get_uart_resource(). We have already a few users
one of which is converted here.
Rationale of this is to consolidate parsing UART Serial Bus
resource in one place as it's done, e.g., for I²C Serial Bus.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210806111736.66591-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function stm32_usart_init_port, intent of the code maybe when
irq returns a value of zero, the return should be '-ENODEV'. But the
conditional expression '? :' maybe clerical error, it should be
'?:' to make '-ENODEV' work.
But in fact, as the example in platform.c is
* int irq = platform_get_irq(pdev, 0);
* if (irq < 0)
* return irq;
So the return value of zero is unnecessary to check, at last remove
the unnecessary '?: -ENODEV'.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210811105136.25392-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby
Lad Prabhakar
Lukas Bulwahn
Jing Yao
Alexander Stein
Patrik John
Johan Hovold
Ilia Sergachev
Sven Eckelmann
Pierre Gondois
Juergen Gross
Linus Torvalds
Geert Uytterhoeven
Andy Shevchenko
Erwan Le Ray
Anssi Hannula
Greg Kroah-Hartman
Arnaud Pouliquen
Xianting Tian
Francesco Dolcini
Stefan Agner
Imran Khan
Guanghui Feng
Uwe Kleine-König
Aman Kumar
Sam Protsenko
Claudiu Beznea
Oskari Pirhonen
Pali Rohár
Colin Ian King
Tony Lindgren
Dan Carpenter
Krzysztof Kozlowski
Jan Beulich
Geert Uytterhoeven
Randy Dunlap
Zhenguo Zhao
Nishanth Menon
Sean Anderson
Len Baker
nick black
Nguyen Dinh Phi
Tang Bin
Fugang Duan
Changbin Du
Ulrich Hecht
Qian Cai
Jakub Kicinski