Hibernation is unsupported for now, which meets the actual
implementation in the driver. For free/thaw, the chip's D2 state should
be entered.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev() used to install a default implementation of this
operation, but it must now be explicitly installed in struct
net_device_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call resource_size(res) returns res->end - res->start + 1 and thus the
second change is semantics-preserving. res_size is then used as the second
argument of a call to request_mem_region, and the memory allocated by this
call appears to be the same as what is released in the two calls to
release_mem_region. So the size argument for those calls should be
resource_size(size) as well. Alternatively, in the second call to
release_mem_region, the second argument could be res_size, as that variable
has already been initialized at the point of this call.
The problem was found using the following semantic patch:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
@@
struct resource *res;
@@
- res->end - res->start
+ BAD(resource_size(res))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc911x_drv_remove() function is declared with __devexit, so the
assignment to the driver structure needs __devexit_p() wrappings to prevent
build failure when hotplug is disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix size of remaped iomem, which is 1 byte to small
(e.g. mappes only 0xff bytes instead of 0x100)
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a power management implementation for smsc911x.c which assumes
the chips remains powered during suspend. The device is put in its D1
power saving mode.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is V2 of the smsc911x fifo byteswap patch.
The smsc911x hardware supports both big and little and endian
hardware configurations, and the linux smsc911x driver currently
detects word order.
For correct operation on big endian platforms lacking swapped
byte lanes the following patch is needed. Only fifo data is
swapped, register data does not require any swapping.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the warning printed when a mii READ times out currently says "Timed out
waiting for MII write to finish". This patch corrects this.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused #include <linux/version.h> in drivers/net/smsc911x.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN911x datasheet specifies a minimum delay of 45ns between a write
of E2P_DATA and any read. This patch adds a single dummy read of
BYTE_TEST to enforce this timing constraint.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the generic eth_mac_addr function with one that
also updates the hardware mac address registers. It also renames the
existing smsc911x_set_mac_address function to
smsc911x_hw_set_mac_address for clarity.
Newer LAN911x and all LAN921x devices also support changing the mac
address while the device is running, which is useful for some bonding
modes.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vast majority of bit constants in this driver are defined in the
header file, but TX and RX status word bits are not. This patch (which
should make no functional change) defines these, to make the driver
slightly more readable.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc911x_phy_adjust_link is called periodically by the phy layer (as
it's run in polling mode), and it only updates the hardware when it sees
a change in duplex or carrier. This patch clears the last known values
every time the interface is brought up, instead of only when the module
is loaded.
Without this patch the adjust_link function never updates the hardware
after an ifconfig down; ifconfig up. On a full duplex link this causes
the tx error counter to increment, even though packets are correctly
transmitted, as the default MAC_CR register setting is for half duplex.
The tx errors are "no carrier" errors, which should be ignored in
full-duplex mode. When MAC_CR is set to "full duplex" mode they are
correctly ignored by the hardware.
Note that even with this patch the tx error counter can increment if
packets are transmitted between "ifconfig up" and the first phy poll
interval. An improved solution would use the phy interrupt with phylib,
but I haven't managed to make this work 100% robustly yet.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch from Juha Leppanen suppresses a false warning if the eeprom
load succeeds on the very last attempt.
Juha> In function smsc911x_open smsc911x_reg_read+udelay can be run 50
Juha> times with timeout reaching -1, and the following if statetement
Juha> does not catch the timeout and no warning is issued. Also if the
Juha> 50th smsc911x_reg_read is GOOD, loop is exited with timeout as 0
Juha> and bogus warning issued. Replace testing order and --timeout
Juha> instead of timeout-- and now max 50 smsc911x_reg_read's are done,
Juha> with max 49 udelays.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch from Juha Leppanen suppresses a false warning if a fast
forward operation succeeds on the very last attempt.
Juha> If smsc911x_reg_read loop is executed 500 times, timeout reaches 0
Juha> and the 500th smsc911x_reg_read result in val is ignored. If
Juha> testing order is changed, then val is checked first. The 500th
Juha> reg_read might be GOOD, why ignore it!
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a postfix decrement timeouts will reach -1 rather than 0, so
the error path does not appear.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some platforms (for example pcm037) do not have an EEPROM fitted,
instead storing their mac address somewhere else. The bootloader
fetches this and configures the ethernet adapter before the kernel is
started.
This patch allows a platform to indicate to the driver via the
SMSC911X_SAVE_MAC_ADDRESS flag that the mac address has already been
configured via such a mechanism, and should be saved before resetting
the chip.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On LAN9115/LAN9117/LAN9215/LAN9217, external phys are supported. These
are usually indicated by a hardware strap which sets an "external PHY
detected" bit in the HW_CFG register.
In some cases it is desirable to override this hardware strap and force
use of either the internal phy or an external PHY. This patch adds
SMSC911X_FORCE_INTERNAL_PHY and SMSC911X_FORCE_EXTERNAL_PHY flags so a
platform can indicate this preference via its platform_data.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The isr supports shared operation, so register it with the IRQF_SHARED
flag to indicate this.
This patch also removes the IRQF_DISABLED flag. This driver doesn't
need it, and IRQF_DISABLED isn't guaranteed when using shared interrupts.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds support for the platform_device's resources to indicate
additional flags to use when registering the irq, for example
IORESOURCE_IRQ_LOWLEVEL (which corresponds to IRQF_TRIGGER_LOW). These
should be set in the irq resource flags field.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc911x_set_multicast_list currently performs the only non-atomic
read-modify-write of INT_EN. This patch permanently enables the
RXSTOP_INT interrupt, and changes the ISR to only conditionally run the
multicast filter workaround code.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change lets "cat /proc/interrupts" show the name of the ethernet
device (e.g. eth0) rather than the driver name (smsc911x).
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if this code path is ever hit, the platform_data struct isn't properly
configured with a bus width flag so the device won't work (hence the
BUG()).
This patch adds a dummy return statement to eliminate this compiler
warning:
drivers/net/smsc911x.c: In function 'smsc911x_reg_read':
drivers/net/smsc911x.c:148: warning: control reaches end of non-void function
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers lost the ability to set ethernet address accidently
during the net_device_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo, the platform_get_resource calls in
smsc911x_drv_remove are supposed to look the same as those in
smsc911x_drv_probe.
Reported and fixed by dfoley@telus.net.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc911x uses driver_data to store our net_device, don't overwrite this
with the mii_bus.
Reported and fixed by dfoley@telus.net.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the module is removed while its interface is up, smsc911x_stop is not
called until after smsc911x_drv_remove has disposed of phy_dev. This
patch changes the stop method to handle this situation.
This is a different problem to the one reported by dfoley@telus.net.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 4 drivers have identical full duplex flow control resolution
functions. This patch changes them all to use one common function.
The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the driver to select 16-bit or 32-bit bus access at runtime,
at a small performance cost.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Daniel Mack
Ben Hutchings
Julia Lawall
Mike Frysinger
Matthias Ludwig
Magnus Damm
Steve Glendinning
Huang Weiyi
David S. Miller
Roel Kluin
Kay Sievers
Ben Hutchings
Stephen Hemminger
Alexey Dobriyan
Neil Horman