The HP lt4132 LTE/HSPA+ 4G Module (03f0:a31d) is a rebranded Huawei
ME906s-158 device. It, like the ME906s-158, requires the "NDP to end"
quirk for correct operation.
Signed-off-by: Tore Anderson <tore@fud.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a985343ba9 ("vxlan: refactor verification and application of
configuration") modified vxlan device creation, and replaced the
assignment of vxlan->net to src_net with dev_net(netdev) in ->setup().
But dev_net(netdev) is not the same as src_net. At the time ->setup()
is called, dev_net hasn't been set yet, so we end up creating the
socket for the vxlan device in init_net.
Fix this by bringing back the assignment of vxlan->net during device
creation.
Fixes: a985343ba9 ("vxlan: refactor verification and application of configuration")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use function set_loopback in phy_driver to setup phy loopback
when doing ethtool self test.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add set_loopback in phy_driver, which is used by MAC
driver to enable or disable phy loopback. it also add a generic
genphy_loopback function, which use BMCR loopback bit to enable
or disable loopback.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CDC-NCM driver can require large amounts of memory to create
skb's and this can be a problem when the memory becomes fragmented.
This especially affects embedded systems that have constrained
resources but wish to maximise the throughput of CDC-NCM with 16KiB
NTB's.
The issue is after running for a while the kernel memory can become
fragmented and it needs compacting.
If the NTB allocation is needed before the memory has been compacted
the atomic allocation can fail which can cause increased latency,
large re-transmissions or disconnections depending upon the data
being transmitted at the time.
This situation occurs for less than a second until the kernel has
compacted the memory but the failed devices can take a lot longer to
recover from the failed TX packets.
To ease this temporary situation I modified the CDC-NCM TX path to
temporarily switch into a reduced memory mode which allocates an NTB
that will fit into a USB_CDC_NCM_NTB_MIN_OUT_SIZE (default 2048 Bytes)
sized memory block and only transmit NTB's with a single network frame
until the memory situation is resolved.
Each time this issue occurs we wait for an increasing number of
reduced size allocations before requesting a full size one to not
put additional pressure on a low memory system.
Once the memory is compacted the CDC-NCM data can resume transmitting
at the normal tx_max rate once again.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP has different physical queue requirements than RoCE
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When computing how much memory is required for the different hw clients
iWARP protocol should be taken into account
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces error handling for errors that occurred during
connection establishment.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of active/passive disconnect flows.
Disconnect flows can be initiated remotely, in which case a async event
will arrive from peer and indicated to qedr driver. These
are referred to as exceptions. When a QP is destroyed, it needs to check
that it's associated ep has been closed.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the active side connect.
Offload a connection, process MPA reply and send RTR.
In some of the common passive/active functions, the active side
will work in blocking mode.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the passive side connect.
It addresses pre-allocating resources, creating a connection
element upon valid SYN packet received. Calling upper layer and
implementation of the accept/reject calls.
Error handling is not part of this patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to add and remove listeners and identify
whether the SYN packet received is intended for iWARP or not. If
a listener is not found the SYN packet is posted back to the chip.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP handles incoming SYN packets using the ll2 interface. This patch
implements ll2 setup and teardown. Additional ll2 connections will
be used in the future which are not part of this patch series.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new connection type for iWARP ll2 connections for setting
correct ll2 filters and connection type to FW.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make some names more generic as they will be used by iWARP too.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds iWARP support for flows that have common code
between RoCE and iWARP, such as initialization, teardown and
qp setup verbs: create, destroy, modify, query.
It introduces the iWARP specific files qed_iwarp.[ch] and
iwarp_common.h
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP personality introduced the need for differentiating in several
places in the code whether we are RoCE, iWARP or either. This
leads to introducing new macros for querying the personality.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in mlx5_core_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZU3mtAAoJEEg/ir3gV/o+4k0IAKj5XCn3cviZlXMJRMHBvamt
yWrMI90XgjoPhGPx3K9mf+bMhHOGiZR0Q2DFDJZa5U64DDBVPNvag7fy74GYgj1D
Cet1zohkQ2xdb/R3jfML8tG2IVfvETWo3cgJGFtGUBlOULvpwinSK4A+8oUUGszc
K1vAY0j3+Ncfjk+CZJ8hWqaIk1dyYtjtyn0ACOUOftqBa6+UZY7LbLTTOI7hOZoX
3M35W7ntgGoBScONlxpDUXNUewia4ADTiQPWwHdT9+xNlwz1fzmCHlYi5pY+z9TC
PKbbe1O4l1nsMftwqJVQNHrFnq+x/X69J5vlgobWkk0dQCRQWE9qanG8BfXPykY=
=DUG8
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-06-28
This series contains some fixes for the mlx5 core and netdev driver.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5e: Fix TX carrier errors report in get stats ndo") Kernels >= v4.7
("net/mlx5: Cancel delayed recovery work when unloading the driver") Kernels >= v4.10
* When applied to net-next this will introduce a contextual conflict, it
should be easy to resolve, (a spin_lock was changed to spin_lock_irqsave in net-next),
if you need any help with this please let me know.
("net/mlx5: Fix driver load error flow when firmware is stuck") Kernels >= v4.4*
* This patch fixes: 6c780a0267 ("net/mlx5: Wait for FW readiness before initializing command interface")
which was submitted two weeks ago and queued up for v4.4.
Sorry about the mess, but other than the above, this series doesn't introduce
any conflict with the current mlx5 IPSec offload series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly fixes and cleanups, but iwlwifi and rtlwifi had also some new
features.
Major changes:
iwlwifi
* some changes in suspend/resume handling to support new FWs
* Continued work towards the A000 family
* support for a new version of the TX flush FW API
* remove some noise from the kernel logs
rtlwifi
* more bluetooth coexistance improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZVenmAAoJEG4XJFUm622bA5IH+wVYmo7BOWXIihYbSnqMcdcq
oRxBygKjti2OUUSwpFfgLN2mR0Drs2tAsziyVtib6dSlR/zPfoyANcoAEEdU/cp3
sUpavj1615+2Un07w8Tj7WSFY1Oqr1HGzzvbAJNdj1MOmQWOcUxNWQaDo2u7uepo
FnJazQ81A/MbyFz9LqWjtpcW4C2duuIQ+c40LepCMN1mjVJvwFDL8gBgK14ZVmn8
/yrbpa+ytJk7Likvn9kk5ubeK0mJvoSvkmXj5AwQIMR0xa6PSjg+nj1hbA1RGcmQ
5D4kGvfrKTTKg9nW+QzFY9L7Fz6DxoPaSVdfJrMlzWNH5SjZvagZZLkx6PLWc98=
=qryd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
Mostly fixes and cleanups, but iwlwifi and rtlwifi had also some new
features.
Major changes:
iwlwifi
* some changes in suspend/resume handling to support new FWs
* Continued work towards the A000 family
* support for a new version of the TX flush FW API
* remove some noise from the kernel logs
rtlwifi
* more bluetooth coexistance improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the flower offloads never sends messages to the hardware,
and never registers a handler for receiving messages from hardware.
This patch enables the flower offloads to send control messages to
hardware when adding and removing flow rules. Additionally it
registers a control message rx handler for receiving stats updates
from hardware for each offloaded flow.
Additionally this patch adds 4 control message types; Add, modify and
delete flow, as well as flow stats. It also allows
nfp_flower_cmsg_get_data() to be used outside of cmsg.c.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously there was no way of updating flow rule stats after they
have been offloaded to hardware. This is solved by keeping track of
stats received from hardware and providing this to the TC handler
on request.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds metadata describing the mask id of each flow and keeps track of
flows installed in hardware. Previously a flow could not be removed
from hardware as there was no way of knowing if that a specific flow
was installed. This is solved by storing the offloaded flows in a
hash table.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds push vlan, pop vlan, output and drop action capabilities
to flower offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends matching capabilities for flower offloads to include vlan,
layer 2, layer 3 and layer 4 type matches. This includes both exact
and wildcard matching.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends the flower flow add function by calculating which match
fields are present in the flower offload structure and allocating
the appropriate space to describe these.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a flower based TC offload handler for representor devices, this
is in addition to the bpf based offload handler. The changes in this
patch will be used in a follow-up patch to add tc flower offload to
the NFP.
The flower app enables tc offloads on representors by default.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phys_switch_id support by allowing lookup of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID via the nfp_repr_port_attr_get
switchdev operation.
This is visible to user-space in the phys_switch_id attribute
of a netdev.
e.g.
cd /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0
find . -name phys_switch_id | xargs grep .
./net/eth3/phys_switch_id:00154d1300bd
./net/eth4/phys_switch_id:00154d1300bd
./net/eth2/phys_switch_id:00154d1300bd
grep: ./net/eth5/phys_switch_id: Operation not supported
In the above eth2 and eth3 and representor netdevs for the first and second
physical port. eth4 is the representor for the PF. And eth5 is the PF netdev.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on original Harini's patch and Andrei's patch,
implemented in a separate file to ease the review/maintanance
and integration with other platforms.
This driver supports GEM-GXL:
- Register ptp clock framework
- Initialize PTP related registers
- HW time stamp on the PTP Ethernet packets are received using the
SO_TIMESTAMPING API. Time stamps are obtained from the dma buffer
descriptors
- add macb_ptp to compilation chain
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that macb is compiled as a module, macb.c has been renamed to
macb_main.c to avoid naming confusion in Makefile.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PTP timestamps in
DMA buffer descriptors. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Some important fixes for 9000 HW;
* FW API changes for the upcoming -30 ucode release;
* A few new PCI IDs for 9000 series;
* Reorganization of common files;
* Some more fixes and improvements here and there
* Initialization and other important fixes for 9000 series;
* Support for version 30 of the FW API for 8000 and 9000 series;
-----BEGIN PGP SIGNATURE-----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=f5vG
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-30' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Final set of patches for 4.13
* Some important fixes for 9000 HW;
* FW API changes for the upcoming -30 ucode release;
* A few new PCI IDs for 9000 series;
* Reorganization of common files;
* Some more fixes and improvements here and there
* Initialization and other important fixes for 9000 series;
* Support for version 30 of the FW API for 8000 and 9000 series;
We should not copy the MCS set from hostapd RX-STBC. We
have to just use the MCS set supported by the hardware.
This fixes an issue, where mwifiex is advertising wrong
MCS sets in beacons.
Fixes: 474a41e94d ("mwifiex: update MCS set as per RX-STBC bit from hostapd")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver used cfg80211_connect_result() which is basically a wrapper
around cfg80211_connect_done() passing a subset of the information that
can be passed. For upcoming functionality this is not sufficient so
switching to use cfg80211_connect_done().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adding callbacks for PMK provisioning. If firmware supports offloading
it is indicated to user-space that 802.1X offload is supported.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware may have supplicant code built-in. This is detected
by the driver and indicated in the wiphy features flags. User-space
can use this flag to determine whether or not to provide the
pre-shared key material in the nl80211 CONNECT command.
Reviewed-by: Gautam (Gautam Kumar) Shukla <gautams@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When filter insertion fails with no rollback, we were trying to convert
EFX_EF10_FILTER_ID_INVALID to an id to store in 'ids' (which is either
vlan->uc or vlan->mc). This would WARN_ON_ONCE and then record a bogus
filter ID of 0x1fff, neither of which is a good thing.
Fixes: 0ccb998bf4 ("sfc: fix filter_id misinterpretation in edge case")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the number of TX queues that are allocated doesn't depend
on the number of TCs, the module always loads with max num of UP
per channel.
In order to prevent the allocation of unnecessary memory, the
module will load with minimum number of UPs per channel, and the
user will be able to control the number of TX queues per channel
by changing the number of TC to 8 using the tc command.
The variable num_up will hold the information about the current
number of UPs.
Due to the change, needed to remove the lines that set the value of
UP to be different than zero in the func "mlx4_en_select_queue",
since now the num of TX queues that are allocated is only one per channel
in default.
In order not to force the UP to be zero in case of only one TC, added
a condition before forcing it in the func "mlx4_en_fill_qp_context".
Tested:
After the module is loaded with minimum number of UP per channel, to
increase num of TCs to 8, use:
tc qdisc add dev ens8 root mqprio num_tc 8
In order to decrease the number of TCs to minimum number of UP per channel,
use:
tc qdisc del dev ens8 root
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Tarick Bedeir <tarick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until this patch, the number of UPs was hard coded for eight.
Replace this with a variable in struct "mlx4_en_port_profile".
Currently, the variable will hold the maximum number of UP,
as before.
The patch creates an infrastructure to add an option for dynamic
change of the actual number of TCs.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Tarick Bedeir <tarick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
19057 392 0 19449 4bf9 drivers/net/ethernet/freescale/gianfar.o
File size After adding 'const':
text data bss dec hex filename
19249 192 0 19441 4bf1 drivers/net/ethernet/freescale/gianfar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
18709 401 0 19110 4aa6 drivers/net/ethernet/smsc/smc91x.o
File size After adding 'const':
text data bss dec hex filename
18901 201 0 19102 4a9e drivers/net/ethernet/smsc/smc91x.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
15426 1256 0 16682 412a drivers/net/ethernet/ibm/ibmveth.o
File size After adding 'const':
text data bss dec hex filename
15618 1064 0 16682 412a drivers/net/ethernet/ibm/ibmveth.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently creates RX/TX queues during device probe, but
assigns IRQ's to them during device open. On reset, however,
IRQ's are assigned when resetting the queues. If there is a reset
while the device is closed and the device is later opened, the driver will
request IRQ's twice, causing the open to fail. This patch assigns
the IRQ's in the ibmvnic_init function after the queues are reset or
initialized, ensuring IRQ's are only requested once.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in netdev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add support for the PCIFB2 card from EAE.
Beside other cards, this card has the backplane mode enabled by default.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We read the backplane mode of each subcard from bits 2 and 3 of the misc
register.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the sysfs interface the read back the backplane
status of the interface.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to track the status of our queued packages. This way the driving
process knows if failed packages need to be retransmitted. For this
purpose we queue the transferred/failed packages back into the err_skb
message queue added with some status information.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the pdev data to the pci devices netdev structure. This way
the interface get consistent device names in the userspace (udev).
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_id was miscalculated. Only the two bits 4-5 are relevant for the
MA1 card. PCIARC1 and PCIFB2 use the four bits 4-7 for id selection.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change some general performance settings and to provide
some performance settings based on the device that is probed.
This includes:
- Setting the maximum read/write outstanding request limit
- Reducing the AXI interface burst length size
- Selectively setting the Tx and Rx descriptor pre-fetch threshold
- Selectively setting additional cache coherency controls
Tested and verified on all versions of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver hardcodes the PBLx8 setting. Remove the need for
specifying the PBLx8 setting and automatically calculate based on the
specified PBL value. Since the PBLx8 setting applies to both Tx and Rx
use the same PBL value for both of them.
Also, the driver currently uses a bit field to set the AXI master burst
len setting. Change to the full bit field range and set the burst length
based on the specified value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In prep for setting fine grained read and write DMA cache coherency
controls, allow specific values to be used to set the cache coherency
registers.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IRQ affinity, set the affinity hints for the IRQs to be (initially) on
the processors corresponding to the NUMA node of the device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to perform memory allocations on the node of the device. The
original allocation or the ring structure and Tx/Rx queues allocated all
of the memory at once and then carved it up for each channel and queue.
To best ensure that we get as much memory from the NUMA node as we can,
break the channel and ring allocations into individual allocations.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the device interrupts should function as level interrupts. For
some hardware configurations this requires setting some control bits
so that if the interrupt status has not been cleared the interrupt
should be reissued.
Additionally, when using MSI or MSI-X interrupts, run the interrupt
service routine as a tasklet so that the re-issuance of the interrupt
is handled properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I2C communication fails, it tends to always fail. Rather than
continuously issue an error message (once per second in most cases),
change the message to be issued just once.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has some missing functionality when operating in the mode that
supports 2.5GbE. Fix the driver to fully recognize and support this speed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the function that performs a software reset of the hardware
provides a return code. During driver probe check this return code and
exit with an error if the software reset fails.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just to be on the safe side, should the update of the timestamp registers
not complete, issue a warning rather than looping forever waiting for the
update to complete.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spurious Tx timestamp interrupts can cause an oops in the Tx timestamp
processing function if a Tx timestamp skb is NULL. Add a check to insure
a Tx timestamp skb is present before attempting to use it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PTP initialization, the Timestamp Control register should be
cleared and not the Tx Configuration register. While this typo causes
the wrong register to be cleared, the default value of each register and
and the fact that the Tx Configuration register is programmed afterwards
doesn't result in a bug, hence only fixing in net-next.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using SFPs, the supported and advertised settings should be initially
based on the SFP that has been detected. The code currently indicates the
overall support of the device as opposed to what the SFP is capable of.
Update the code to change the supported link modes, auto-negotiation, etc.
to be based on the installed SFP.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and centralize the mailbox command rate change interface by
having a single function perform the writes to the mailbox registers
to issue the request.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that ofdpa_neigh_del() can sometimes free
"found". It just makes sense to use it first before deleting it.
Fixes: ecf244f753 ("rocker: fix maybe-uninitialized warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station that's not associated sends a data frame (e.g. an NDP)
hostapd will respond with a disassoc frame, telling it that it's not
associated. The station might also not be authenticated, in which case
there will not be a station entry for it, and as a result we need to
accept such frames without a station.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a non-STA frame to transmit in client mode, we try to use
the IWL_MVM_DQA_BSS_CLIENT_QUEUE queue (queue #4). However, at this
point, the queue might not be allocated at all, causing warnings. The
scenario on which this happened was a race condition between mac80211
and our queue allocation work:
* mac80211 sends auth
* we stop mac80211 queues to allocate a hw queue
* authentication is aborted
* we allocate HW queue and start mac80211 queues
* mac80211 removes station
* mac80211 hands us the auth frame from the pending queue
At this point, since mac80211 has already removed the station, we try
to transmit the frame through this special non-station case on queue
4 anyway.
In order to really use it properly, we'd have to again go through the
hw queue allocation work, and attach it to a station, etc. In this
case that isn't possible (there's no station anymore), but if this
special case were needed, then we'd have to do it this way.
However, the special case is documented to exist for TDLS, but can't
trigger there because the TDLS setup frames etc. are normal to-DS
frames going to the peer through the AP. Testing also confirms that
this code path isn't triggered in TDLS.
Therefore, remove the code path to avoid using an unused queue. The
erroneous frame described above will still be transmitted on the AUX
queue, but arguably that's a mac80211 problem, which will eventually
be fixed by moving everything there to TXQs.
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get large sends on non-QoS association, we had a
bug that mangled the SNAP header. Fix that.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When going into suspend, the HW configuration for MSI-X will
likely be lost. As a consequence, after waking up, all IRQ
causes will be mapped to interrupt 0, and as a consequence we
don't notice the interrupt because in most cases this is an
interrupt for a queue, and getting it doesn't read the other
cause registers.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the TID of a packet before we know it is a QoS data
packet isn't a good idea. Delay the TID retrieval until
we know the packet is a QoS data packet.
Fixes: bb81bb68f4 ("iwlwifi: mvm: add Tx A-MSDU inside A-MPDU")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When in non-DQA mode, mac80211 actually gets a pretty much perfect
idea (in vif->hw_queue/cab_queue) of which queues we're using. But
in DQA mode, this isn't true - nonetheless, we were adding all the
queues, even the ones stations are using, to the queue allocation
bitmap.
Fix this, we should only add the queues we really are using in DQA
mode:
* IWL_MVM_OFFCHANNEL_QUEUE, as we use this in both modes
* mvm->aux_queue, as we use this in both modes - mac80211
never really knows about it but we use it as a cookie
internally, so can't reuse it
* possibly the GCAST queue (cab_queue)
* all the "queues" we told mac80211 about we were using on each
interface (vif->hw_queue), these are entirely virtual in this
mode
Also add back the failure now when we can't allocate any more of
these - now virtual - queues; this was skipped in DQA mode and
would lead to having multiple ACs or even interfaces use the same
queue number in mac80211 (10, since that's the limit), which would
stop far too many queues if stopped.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There may be a difference between the mac80211 vif->cab_queue and
mvmvif->cab_queue, particularly with TVQM. Make the code map this
earlier, instead of first returning the mac80211 one again from
iwl_mvm_get_ctrl_vif_queue().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the driver, we track which hardware queue is associated with
which mac80211 "hw_queue", in order to be able to stop and wake
it. When moving these bitmaps out of the queue_info structures,
the type of the bitmap was erroneously changed from u32 to u8,
presumably in order to save memory.
Turns out that u32 isn't needed, because the highest queue we
can ever tell mac80211 is always < 16, but a u16 definitely is
needed, queues >=8 do happen.
While at it, throw a BUILD_BUG_ON() into the place where we set
the limit (mvm->first_agg_queue) and a warning when it actually
gets put into the bitmap.
The consequence of this bug is that full HW queues associated
with such a too-high mac80211 number never stop higher layer
queues when full, and thus would simply drop all packets that
couldn't be enqueued to the hardware queue.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code was intended to enable IP header checksumming on AMSDUs, but
failed to really do so because the A-MSDU bit was set after all the
checksumming bits, and thus checking for A-MSDU could never be true.
Fix this by setting the A-MSDU bit before the offload bits.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have tracing for both pre-ICT and ICT interrupts, including all
the data read there. Extend the tracing to MSI-X interrupts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case a VLAN device is enslaved to a bridge we shouldn't create a
router interface (RIF) for it when it's configured with an IP address.
This is already handled by the driver for other types of netdevs, such
as physical ports and LAG devices.
If this IP address is then removed and the interface is subsequently
unlinked from the bridge, a NULL pointer dereference can happen, as the
original 802.1d FID was replaced with an rFID which was then deleted.
To reproduce:
$ ip link set dev enp3s0np9 up
$ ip link add name enp3s0np9.111 link enp3s0np9 type vlan id 111
$ ip link set dev enp3s0np9.111 up
$ ip link add name br0 type bridge
$ ip link set dev br0 up
$ ip link set enp3s0np9.111 master br0
$ ip address add dev enp3s0np9.111 192.168.0.1/24
$ ip address del dev enp3s0np9.111 192.168.0.1/24
$ ip link set dev enp3s0np9.111 nomaster
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Tested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't hold any tx lock when trying to disable TX during reset, this
would lead a use after free since ndo_start_xmit() tries to access
the virtqueue which has already been freed. Fix this by using
netif_tx_disable() before freeing the vqs, this could make sure no tx
after vq freeing.
Reported-by: Jean-Philippe Menil <jpmenil@gmail.com>
Tested-by: Jean-Philippe Menil <jpmenil@gmail.com>
Fixes commit f600b69050 ("virtio_net: Add XDP support")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Robert McCabe <robert.mccabe@rockwellcollins.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 3.70a of the Designware has additional DMA registers so
add those to the ethtool DMA Register dump.
Offset 9 - Receive Interrupt Watchdog Timer Register
Offset 10 - AXI Bus Mode Register
Offset 11 - AHB or AXI Status Register
Offset 22 - HW Feature Register
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset adds support for Innova IPSec network interface card.
About Innova device:
--------------------
Innova is a network card with a ConnectX chip and an FPGA chip as a
bump-on-the-wire.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ I2C | | SBU | | +------+
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | Flash |
+-----+ +-------+
The FPGA synthesized logic is loaded from dedicated flash storage and has
access to its own dedicated DDR RAM.
The ConnectX chip firmware programs the FPGA by accessing its configuration
space over either the slow internal I2C link or the high-speed internal link.
The FPGA logic is divided into a "Shell" and a "Sandbox Unit" (SBU).
mlx5_core driver (with CONFIG_MLX5_FPGA) handles all shell functionality,
while other components may handle the various SBU functionalities.
The driver opens high-speed reliable communication channels with the shell and
the SBU over the internal link.
These channels may be used for high-bandwidth configuration or for SBU-specific
out-of-band data paths.
About Innova IPSec device:
--------------------------
Innova IPSec is a network card that allows offloading IPSec cryptography operations
from the host CPU to the NIC. It is an Innova card with an IPSec SBU.
The hardware keeps the database of IPSec Security Associations (SADB) in the FPGA's
DDR memory.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ Internal I2C | | IPSec | | +------+
| | SBU | |
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | |
| | | Flash |
|SADB | | |
+-----+ +-------+
Modes and ciphers:
Currently the following modes and ciphers are supported:
IPv4 and IPv6
ESP tunnel and transport modes
AES 128 and 256 bit encryption, with GCM authentication (RFC4106)
IV is generated using seqiv, in sync with Linux's geniv.
More modes and ciphers may be added later.
Notes:
In the future similar functionality will be included in a single-chip NIC.
About the driver:
-----------------
Patches 1-4 prepare some existing driver code for the new feature:
* Add support for reserved GIDs in the hardware GID table
* Allow multiple modules to enable hardware RoCE support independently
Patches 5-6 define structs and helper functions for QP work-queues.
Patches 7-11 add various FPGA-related features required for Innova.
IPSec.
Patch 12 adds abstraction layer for Mellanox IPSec-offload capable devices.
atches 13-16 add IPSec offload support to the mlx5 netdevice.
This driver services the new IPSec offload API introduced in commit
d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Configuration Path:
If Innova IPSec device is detected, the mlx5e netdevice gets the new
NETIF_F_HW_ESP feature and the xdo callbacks, indicating ESP offload
capabilities, and also the matching TX checksum and GSO features.
The driver configures offloaded Security Associations (SAs) by sending
an ADD_SA or DEL_SA message to the IPSec SBU, which updates the SADB in DDR.
These messages and their responses are sent over a high-speed channel.
Counters for ethtool are retrieved by the driver from the SBU.
Data path:
On receive path, the SBU decrypts ESP packets which match the offloaded SADB,
but keeps them encapsulated.
The SBU injects metadata (Mellanox owned ethertype) indicating that crypto-offload
has taken place, the SA with which it was done, and the authentication result.
The ConnectX chip performs RX checksum offload on the packet, and RSS using the
ESP SPI value. The driver detects the special ethertype, and attaches a struct
secpath to the RX SKB, including flags to indicate that crypto offload took place,
the authentication result, and which xfrm_state was used for decryption, in the
olen and ovec members. The RX SKB may have useful CHECKSUM_COMPLETE. A separate
patchset will add support for that in the xfrm stack.
On transmit path, the stack encapsulates the packet but does not encrypt it, and
indicates in the SKB's secpath that crypto offload is to be performed and the SA
to use to do so.
The driver avoids performing crypto-offload for ESP fragments, and packets with
IP options, as the SBU cannot currently do that. For eligible packets, the driver
prepends a special ethertype with metadata instructing the hardware to perform crypto offload.
The stack builds regular (non-GSO) SKBs so that they contain a placeholder for the ESP trailer.
The driver trims it off, because the SBU automatically appends the trailer for offloaded packets.
The ConnectX chip performs TX checksum offload on inner UDP or TCP packets,
and GSO for TCP packets (duplicating the prepended metadata).
The segmented packets then undergo encryption in the SBU before going on the wire.
Performance:
We measure single stream of TCP on Intel(R) Xeon(R) CPU E5-2643 v2 @3.50GHz
Using AES-NI with ESP GSO we get constant 4.1 Gbps.
Using crypto offload we get constant 18 Gbps.
Note that these numbers require CHECKSUM_COMPLETE support in XFRM, which we submit separately.
- Ilan Tayari
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZUmf1AAoJEEg/ir3gV/o+ukIIALp/5+E1W0cC9xvY1X9dTETW
cKsHvDJ7G1CxUy18W8Mf9z+WOqC6hGCqS+yicOb+umfIqkTcLHDb2irlqprYLC+F
oYl1HqgHTaiAYByqL90qiyPcFbfsaNIqA9KOsED2qdZ1yxjoYBiJnSDZDAdO/0lN
Lt1czNswFc5ovnEUGn8bkjLZZH2pJoJWEI4g4hN9cq33BLLq8A795F/ZjwCJTQ1X
qXdKcEmktBrgZiSiTVFxxpQVhO/uB0HmzaZzrY1k1P5e6yhHEr422mcOcF9KcSL4
aeyRYHjoIh51vPMbScPjvfbO/PwooU3LWLlxLVNLG0MmkSaGyJeUXg/wHsGI910=
=JN0A
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-06-27 (Innova IPsec offload support)
This patchset adds support for Innova IPSec network interface card.
About Innova device:
--------------------
Innova is a network card with a ConnectX chip and an FPGA chip as a
bump-on-the-wire.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ I2C | | SBU | | +------+
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | Flash |
+-----+ +-------+
The FPGA synthesized logic is loaded from dedicated flash storage and has
access to its own dedicated DDR RAM.
The ConnectX chip firmware programs the FPGA by accessing its configuration
space over either the slow internal I2C link or the high-speed internal link.
The FPGA logic is divided into a "Shell" and a "Sandbox Unit" (SBU).
mlx5_core driver (with CONFIG_MLX5_FPGA) handles all shell functionality,
while other components may handle the various SBU functionalities.
The driver opens high-speed reliable communication channels with the shell and
the SBU over the internal link.
These channels may be used for high-bandwidth configuration or for SBU-specific
out-of-band data paths.
About Innova IPSec device:
--------------------------
Innova IPSec is a network card that allows offloading IPSec cryptography operations
from the host CPU to the NIC. It is an Innova card with an IPSec SBU.
The hardware keeps the database of IPSec Security Associations (SADB) in the FPGA's
DDR memory.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ Internal I2C | | IPSec | | +------+
| | SBU | |
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | |
| | | Flash |
|SADB | | |
+-----+ +-------+
Modes and ciphers:
Currently the following modes and ciphers are supported:
IPv4 and IPv6
ESP tunnel and transport modes
AES 128 and 256 bit encryption, with GCM authentication (RFC4106)
IV is generated using seqiv, in sync with Linux's geniv.
More modes and ciphers may be added later.
Notes:
In the future similar functionality will be included in a single-chip NIC.
About the driver:
-----------------
Patches 1-4 prepare some existing driver code for the new feature:
* Add support for reserved GIDs in the hardware GID table
* Allow multiple modules to enable hardware RoCE support independently
Patches 5-6 define structs and helper functions for QP work-queues.
Patches 7-11 add various FPGA-related features required for Innova.
IPSec.
Patch 12 adds abstraction layer for Mellanox IPSec-offload capable devices.
atches 13-16 add IPSec offload support to the mlx5 netdevice.
This driver services the new IPSec offload API introduced in commit
d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Configuration Path:
If Innova IPSec device is detected, the mlx5e netdevice gets the new
NETIF_F_HW_ESP feature and the xdo callbacks, indicating ESP offload
capabilities, and also the matching TX checksum and GSO features.
The driver configures offloaded Security Associations (SAs) by sending
an ADD_SA or DEL_SA message to the IPSec SBU, which updates the SADB in DDR.
These messages and their responses are sent over a high-speed channel.
Counters for ethtool are retrieved by the driver from the SBU.
Data path:
On receive path, the SBU decrypts ESP packets which match the offloaded SADB,
but keeps them encapsulated.
The SBU injects metadata (Mellanox owned ethertype) indicating that crypto-offload
has taken place, the SA with which it was done, and the authentication result.
The ConnectX chip performs RX checksum offload on the packet, and RSS using the
ESP SPI value. The driver detects the special ethertype, and attaches a struct
secpath to the RX SKB, including flags to indicate that crypto offload took place,
the authentication result, and which xfrm_state was used for decryption, in the
olen and ovec members. The RX SKB may have useful CHECKSUM_COMPLETE. A separate
patchset will add support for that in the xfrm stack.
On transmit path, the stack encapsulates the packet but does not encrypt it, and
indicates in the SKB's secpath that crypto offload is to be performed and the SA
to use to do so.
The driver avoids performing crypto-offload for ESP fragments, and packets with
IP options, as the SBU cannot currently do that. For eligible packets, the driver
prepends a special ethertype with metadata instructing the hardware to perform crypto offload.
The stack builds regular (non-GSO) SKBs so that they contain a placeholder for the ESP trailer.
The driver trims it off, because the SBU automatically appends the trailer for offloaded packets.
The ConnectX chip performs TX checksum offload on inner UDP or TCP packets,
and GSO for TCP packets (duplicating the prepended metadata).
The segmented packets then undergo encryption in the SBU before going on the wire.
Performance:
We measure single stream of TCP on Intel(R) Xeon(R) CPU E5-2643 v2 @3.50GHz
Using AES-NI with ESP GSO we get constant 4.1 Gbps.
Using crypto offload we get constant 18 Gbps.
Note that these numbers require CHECKSUM_COMPLETE support in XFRM, which we submit separately.
- Ilan Tayari
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is cpts function to check if packet can be timstamped with cpts.
Seems that ptp_classify_raw cover all cases listed with "case".
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpts can timestmap only ptp packets at this moment, so driver
cannot mark every packet as though it's going to be timestamped,
only because h/w timestamping for given skb is enabled with
SKBTX_HW_TSTAMP. It doesn't allow to use sw timestamping, as result
outgoing packet is not timestamped at all if it's not PTP and h/w
timestamping is enabled. So, fix it by setting SKBTX_IN_PROGRESS
only for PTP packets.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move sw timestamp function close to channel submit function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using netdev_<level>(netdev, "%s: ...", netdev->name) duplicates the
name in the output. Remove those uses.
Miscellanea:
o Use the netif_<level> convenience macros at the same time
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in mlx4_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in netif_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current way to find if the phy is internal is to compare DT phy-mode
and emac_variant/internal_phy.
But it will negate a possible future SoC where an external PHY use the
same phy mode than the internal one.
By using phy-mode = "internal" we permit to have an external PHY with
the same mode than the internal one.
Reported-by: André Przywara <andre.przywara@arm.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond_options.c file contains multiple netdev_info statements that clutter kernel output.
This patch replaces all netdev_info with netdev_dbg and adds a netdev_dbg statement for the
packets per slave parameter. Also fixes misalignment at line 467.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael J Dilmore <michael.j.dilmore@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hostapd adds a station, it does so before sending the association
response frame, so that it can indicate the correct status code in the
response.
However, when this then fails, or the association response already is
a reject for some other reason, then there's no station entry and thus
no per-station management queue to send the response on and it must be
sent on the probe response queue. The code should therefore not warn.
In theory, we could check and warn if the status code is success, but
that seems excessive, so just relax the check to allow any association
response frames.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Only a000-series devices were going to use this, but actually
initialize using the context info, which includes paging, so
this code is never invoked; remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we now support 8 device families, move their configuration
files into a new subdirectory "cfg".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the notification wait code into the new fw interaction directory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This structure represents V2, V1 has the three last fields missing.
Rename it to be more accurate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the first frame on a given TID is received with seqno 0 and needed
to be retransmitted, we erroneously drop it because the deduplication
data is initialized to zero, and then comparing
if (unlikely(ieee80211_has_retry(hdr->frame_control) &&
dup_data->last_seq[tid] == hdr->seq_ctrl &&
dup_data->last_sub_frame[tid] >= sub_frame_idx))
return true;
will return in iwl_mvm_is_dup() since last_sub_frame is also set to
zero, and sub_frame_idx is usually zero since this only covers the
relatively rare case of A-MSDU.
Fix this by initializing the last_seq array to 0xffff, which is an
impossible value for hdr->seq_ctrl to have here because the lower
four bits are the fragment number, and fragments aren't handled in
this code but go to mac80211 instead.
Fixes: a571f5f635 ("iwlwifi: mvm: add duplicate packet detection per rx queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In commit b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work
as expected"), the code was changed to make the stop conditional
on not having failed (and on not having init_dbg), which doesn't
make sense - we should stop the device regardless of failures.
Failure to do so is leading to the device being enabled when it
shouldn't be, and - if it gets re-enabled later - the new context
info code gets confused as paging data wasn't freed.
Remove the invalid error condition again.
Fixes: b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work as expected")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This appears to happen in some cases, like when iwlmvm is unloaded and
loaded again without also unloading iwlwifi. Warn in this case and free
the paging data to be able to continue without causing corruption and
kernel crashes due to it (otherwise, paging data is overwritten, but
dram->paging_cnt gets to be twice as big as it should be, and then an
eventual free will crash.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
By setting the pointers to NULL at the end, these functions
are made idempotent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When receiving a BA_NOTIF on new TX API, it can
contain BAs for several TIDs. Go over them and
reclaim TX for every TID.
Note that although the small API change, the API
version still isn't bumped forward, as this NIC
isn't still officially released.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The BT_COEX command should not be sent to the INIT
firmware image starting from 8000 family.
The firmware team also requested to send the BT_COEX
command after the PHY_DB_CMD and the PHY_CFG_CMD.
While at it:
s/iwl_send_bt_init_conf/iwl_mvm_send_bt_init_conf/
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print the queue for the existing debug message and add a new
debug message indicating where the RB ended.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A SCD bug was fixed in the A000 family, allowing to
support aggregations of 64 frames (rather than 63).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print out both queue IDs to be able to see what went wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware supports CDB, PHY contexts cannot be modified to
change their band, but need to be added/remove instead. Instead of
relying on iwl_mvm_has_new_tx_api(), check the right FW capa flag
IWL_UCODE_TLV_CAPA_BINDING_CDB_SUPPORT and remove the comment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new config struct for the new a000 2ax series and add
the five PCI ID for it.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no reason to pass mvm and trig as parameters to the macro,
since it will be expanded inside the function itself. Also remove the
bogus buf parameter which doesn't exist and is not used.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The sta_id variable is used as an index in an array, should be unsigned.
Found by Klocwork.
Fixes: 9f9af3d7d3 ("iwlwifi: mvm: re-aggregate shared queue after unsharing")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A hardware issue on 9000 series devices sometimes causes RF-kill
interrupts to not be propagated to the host properly if ASPM is
enabled. Work around this by setting the right hardware bit to
allow it to interrupt the host for this reason (rfkill).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to a hardware issue, certain power saving had to be
disabled. However, this issue was fixed in B-step, so the
workaround only needs to apply to A-step.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some static checkers (e.g. smatch) complain if a non-constant
format string is used, even if that's a static const variable.
Since there's no impact on code generation, just change those
format strings to be macros.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the kernel-doc, and remove some fields even the firmware doesn't
use in ToF, RX, scan, station and generic FW APIS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix various "Excess struct/union/enum/typedef member '...' description
in '...'" warnings from kernel-doc, mostly caused by typos.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a debugfs entry to get a verbose description of the power settings
used in each band with the currently selected SAR geographic profile.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We are going to add debugfs entry to retrieve the current geographic
profile being used in the FW. Currently the driver reads those tables
from the BIOS and passes them to the FW.
To prepare for this retrieving we want to store those
tables in the driver.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trivial fix to spelling mistake in mwifiex_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check return value from call to wl18xx_top_reg_write(),
so in case of error jump to goto label out and return.
Also, remove unnecessary value check before goto label out.
Addresses-Coverity-ID: 1226938
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kstrtoul() test was reversed so this always returned -ENOTSUPP.
Fixes: 27d7f47756 ("net: wireless: replace strict_strtoul() with kstrtoul()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Declare hwbus_ops structures as const as they are only passed as an
argument to the function cw1200_core_probe. This argument is of type
const. So, make these structures const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two recent commits added new RSI_FSM_STATES (namely FSM_FW_NOT_LOADED
and FSM_COMMON_DEV_PARAMS_SENT) and the corresponding table fsm_state
was not updated to match. This can lead to an array overrun when
accessing the latter two states in fsm_state. Fix this by adding in
the missing states.
Detected by CoverityScan, CID#1398379 ("Illegal address computation")
Fixes: 9920322ccd ("rsi: add tx frame for common device configuration")
Fixes: 015e367494 ("rsi: Register interrupt handler before firmware load")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 9cc4b7cb86 ("brcmfmac: Make skb header writable
before use") the headroom usage has been fixed. However, the
driver was keeping statistics that got lost. So reworking the
code so we get those driver statistics back for debugging.
Cc: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The statistic counter is used in common layer and in the bus layer
in different thread contexts so change to use atomic operations.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A couple of old fields were still described and one field was not
described.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When user adds a virtual interface driver will set the
bss_type to the iface_type given by the user. When
supplicant is started on the same interface, a call to
change_virtual_intf will be triggered if if_type is not
NL80211_IFTYPE_STATION. Here driver should not update
it's bss_type, because bss_type is intended to indicate
the original iface_type and changing the same will defeat
the purpose of creating this interface.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If wifi is in 4way, btcoex give wifi higher priority to use antenna.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there are many AP (dirty environment), we use another strategy set
to resolve coex issue.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will use return value to handle error case.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return value may be false in some situations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify 8723be and 8192e only.
8812/8821 do IQK in DM, so we may do it later.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this case, BTC asks to enter/leave PS mode frequently to cause A2DP
choppy.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value ret is unitialized and garbage is being returned
for the three different error conditions when setting up the PCIe
BARs. Fix this by initializing ret to -ENOMEM to indicate that
the BARs failed to be setup correctly.
Detected by CoverityScan, CID#1437563 ("Unitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tore Anderson
Sabrina Dubroca
Lin Yun Sheng
Stephen Rothwell
Jim Baxter
Kalderon, Michal
Edward Cree
Jon Cooper
Colin Ian King
David S. Miller
Pieter Jansen van Vuuren
Simon Horman
Reshetova, Elena
Rafal Ozieblo
Kalle Valo
Ganapathi Bhat
Arend van Spriel
Arend van Spriel
Inbar Karmy
Arvind Yadav
Thomas Falcon
Michael Grzeschik
Lendacky, Thomas
Dan Carpenter
Luca Coelho
Emmanuel Grumbach
Johannes Berg
Liad Kaufman
Ido Schimmel
Jason Wang
Thor Thayer
Ivan Khoronzhuk
Joe Perches
LABBE Corentin
Michael Dilmore
Tzipi Peres
Sharon Dvir
Haim Dreyfuss
Gustavo A. R. Silva
Bhumika Goyal
Ping-Ke Shih