'const static ' is not a common order, better to use 'static const' instead.
building:
make EXTRA_CFLAGS=-W ARCH=arm
drivers/gpio/gpio-omap.c:1479:
warning: 'static' is not at beginning of declaration
drivers/gpio/gpio-omap.c:1485:
warning: 'static' is not at beginning of declaration
drivers/gpio/gpio-omap.c:1491:
warning: 'static' is not at beginning of declaration
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2XeO
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO updates from Grant Likely:
"GPIO follow up patch and type change for v3.5 merge window
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio: Provide the STMPE GPIO driver with its own IRQ Domain
gpio: add TS-5500 DIO blocks support
gpio: pcf857x: use client->irq for gpio_to_irq()
gpio: stmpe: Add DT support for stmpe gpio
gpio: pl061 depends on ARM
gpio/pl061: remove old comment
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
GPIO: clps711x: use platform_device_unregister in gpio_clps711x_init()
gpio/tc3589x: convert to use the simple irqdomain
...
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change was originally titled "gpio/omap: fix off-mode bug: clear debounce
clock enable mask on free/reset". The title has been updated slightly to
reflect (what should be) the final fix.
When a GPIO is freed or shutdown, we need to ensure that any debounce settings
are cleared and if the GPIO is the only GPIO in the bank that is currently
using debounce, then disable the debounce clock as well to save power.
Currently, the debounce settings are not cleared on a GPIO free or shutdown and
so during a context restore on subsequent off-mode transition, the previous
debounce values are restored from the shadow copies (bank->context.debounce*)
leading to mismatch state between driver state and hardware state.
This was discovered when board code was doing
gpio_request_one()
gpio_set_debounce()
gpio_free()
which was leaving the GPIO debounce settings in a confused state. If that GPIO
bank is subsequently used with off-mode enabled, bogus state would be restored,
leaving GPIO debounce enabled which then prevented the CORE powerdomain from
transitioning.
To fix this, introduce a new function called _clear_gpio_debounce() to clear
any debounce settings when the GPIO is freed or shutdown. If this GPIO is the
last debounce-enabled GPIO in the bank, the debounce will also be cut.
Please note that we cannot use _gpio_dbck_disable() to disable the debounce
clock because this has been specifically created for the gpio suspend path
and is intended to shutdown the debounce clock while debounce is enabled.
Special thanks to Kevin Hilman for root causing the bug. This fix is a
collaborative effort with inputs from Kevin Hilman, Grazvydas Ignotas and
Santosh Shilimkar.
Testing:
- This has been unit tested on an OMAP3430 Beagle board, by requesting a gpio,
enabling debounce and then freeing the gpio and checking the register
contents, the saved register context and the debounce clock state.
- Kevin Hilman tested on 37xx/EVM board which configures GPIO debounce for the
ads7846 touchscreen in its board file using the above sequence, and so was
failing off-mode tests in dynamic idle. Verified that off-mode tests are
passing with this patch.
V5 changes:
- Corrected author
Reported-by: Paul Walmsley <paul@pwsan.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A pointer to "pdev->dev" is already stored in "dev", so use it in
devm_kzalloc.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQaO1fAAoJEIwa5zzehBx3IPgP/jxoO1flVGNVf0reqqyDro/w
prZmp8cNVH9uv8xG9n9vawObrMQ8M6jCJ449fEWuAZ58EXrpIPd0kkm/MOmxp8K1
LNs+q2aXxWpD488+b3RK55g3fksqZutTbn3y6HNuCoLG9l8yT/95KX4IIzfEP2Ch
1TCNHdkTbf37nTBOmKN0x1kahGpWDrOkf9ysHQq+DXAGF4uwNwtR194dqz3HbDND
hZqRq7qCLn9OwGRGNicPFoB6UcxwZ/+/+u5sX7nqPGoiPofg977mhWk1DFO15EM3
S+A6g0dZ+XLsL+fFtOl4snSmrG5Et6qTOP0/ItQJgTG+5YdCS09ohCWJwRCBHbgj
M5arOkyGFdVAlvX7cUux374sMe0AcqUsEmt79mYuBpIE+pBJaRUoCgDcs9FDZeUB
U6WcE4AkxMtW7DtmVW+mF4ls9/K6cRXgWMuHCUmt1o3m3Ly9ITT7j+ntXnD9nuYk
ndoVLR6Vxk2BzlkD0JEtg7FRAS9Wgo2DBix05qM1Qkut2iIZRhFQlqJQpNbeNdii
/3Lg/hqpAVTZKGCd+paegHez61meyFz2PB2IiE0JKANhKHRCWTWRGgKIXkGyCiXk
wJ2iRCOlMEpmpJgCBzfI32ER/hnW4s64iDjgksEwz6pEt7xCbhwgmwrpf0H0KsSF
rLroHOMqyISd/Ha52Vin
=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.
Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.
While at it, arrange the related includes in the standard way.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since of_device_id.data is declared as a pointer to const data a few
more consts can be added in this driver.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/gpio/gpio-omap.c: In function 'omap_gpio_probe':
drivers/gpio/gpio-omap.c:1060: warning: assignment discards qualifiers from pointer target type
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- New driver for AMD-8111 southbridge GPIOs
- New driver for Wolfson Micro Arizona devices
- Propagate device tree parse errors
- Probe deferral finalizations - all expected calls to
GPIO will now hopefully request deferral where apropriate
- Misc updates to TCA6424, WM8994, LPC32xx, PCF857x, Samsung
MXC, OMAP and PCA953X drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tujx
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
- New driver for AMD-8111 southbridge GPIOs
- New driver for Wolfson Micro Arizona devices
- Propagate device tree parse errors
- Probe deferral finalizations - all expected calls to GPIO will now
hopefully request deferral where apropriate
- Misc updates to TCA6424, WM8994, LPC32xx, PCF857x, Samsung MXC, OMAP
and PCA953X drivers.
Fix up gpio_idx conflicts in drivers/gpio/gpio-mxc.c
* tag 'gpio-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: of_get_named_gpio_flags() return -EPROBE_DEFER if GPIO not yet available
gpiolib: Defer failed gpio requests by default
MAINTAINERS: add entry OMAP GPIO driver
gpio/pca953x: increase variables size to support 24 bit of data
GPIO: PCA953X: Increase size of invert variable to support 24 bit
gpio/omap: move bank->dbck initialization to omap_gpio_mod_init()
gpio/mxc: use the edge_sel feature if available
gpio: propagate of_parse_phandle_with_args errors
gpio: samsung: add flags specifier to device-tree binding
gpiolib: Add support for Wolfson Microelectronics Arizona class devices
gpio: gpio-lpc32xx: Add gpio_to_irq mapping
gpio: pcf857x: share 8/16 bit access functions
gpio: LPC32xx: Driver cleanup
MAINTAINERS: Add Wolfson gpiolib drivers to the Wolfson entry
gpiolib: wm8994: Convert to devm_kzalloc()
gpiolib: wm8994: Use irq_domain mappings for gpios
gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips
gpio/tca6424: merge I2C transactions, remove cast
gpio/of: fix a typo of comment message
Since the bank->dbck initialization in a one time operation there
is no need to keep this within gpio_debounce(). Therefore, moving
clk_get(bank->dbck) to omap_gpio_mod_init(). Since the value of
bank->dbck would be NULL at the beginning, this check has been
removed.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reported-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the gpio _runtime_resume/suspend functions are calling the
get_context_loss_count() platform function if the function is populated for
a gpio bank. This function is used to determine if the gpio bank logic state
needs to be restored due to a power transition. This function will be populated
for all banks, but it should only be called for banks that have the
"loses_context" variable set. It is pointless to call this if loses_context is
false as we know the context will never be lost and will not need restoring.
For all OMAP2+ devices gpio bank-0 is in an always-on power domain and so will
never lose context. We found that the get_context_loss_count() was being called
for bank-0 during the probe and returning 1 instead of 0 indicating that the
context had been lost. This was causing the context restore function to be
called at probe time for this bank and because the context had never been saved,
was restoring an invalid state. This ultimately resulted in a crash [1].
This issue is a regression that was exposed by commit 1b1287032 (gpio/omap: fix
missing check in *_runtime_suspend()).
There are multiple bugs here that need to be addressed ...
1. Why the always-on power domain returns a context loss count of 1? This needs
to be fixed in the power domain code [2]. However, the gpio driver should not
assume the loss count is 0 to begin with.
2. The omap gpio driver should never be calling get_context_loss_count for a
gpio bank in a always-on domain. This is pointless and adds unneccessary
overhead.
3. The OMAP gpio driver assumes that the initial power domain context loss count
will be 0 at the time the gpio driver is probed. However, it could be
possible that this is not the case and an invalid context restore could be
performed during the probe. To avoid this only populate the
get_context_loss_count() function pointer after the initial call to
pm_runtime_get() has occurred. This will ensure that the first
pm_runtime_put() initialised the loss count correctly.
This patch addresses issues 2 and 3 above.
[1] http://marc.info/?l=linux-omap&m=134065775323775&w=2
[2] http://marc.info/?l=linux-omap&m=134100413303810&w=2
Cc: Kevin Hilman <khilman@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Franky Lin <frankyl@broadcom.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: NeilBrown <neilb@suse.de>
Reported-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Franky Lin <frankyl@broadcom.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It seems that currently GPIO module is not working correctly during idle
when debounce is enabled - the system almost never responds to button
presses (observed on OMAP3530 ES2.1 and OMAP3630 ES1.2 pandora boards).
Even though wakeups are probably working, it seems that the GPIO module
itself is unable to detect input events and generate interrupts.
OMAP35x TRM also states that:
"If the debounce clock is inactive, the debounce cell gates all
input signals and thus cannot be used."
So whenever we are disabling debounce clocks (for PM or other reasons),
be sure the module's debounce feature is disabled too.
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
commit 1b1287032 (gpio/omap: fix missing check in *_runtime_suspend())
broke wakeups on level-triggered GPIOs by adding the enabled
non-wakeup GPIO check before the workaround that enables wakeups
on level-triggered IRQs, effectively disabling that workaround.
To fix, move the enabled non-wakeup GPIO check after the
level-triggered IRQ workaround.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The fix in commit 1b1287032 (gpio/omap: fix missing check in
*_runtime_suspend()) exposed another bug in the context restore path.
Currently, the per-bank context restore happens whenever the context
loss count is different in runtime suspend and runtime resume *and*
whenever the per-bank contex_loss_count == 0:
if (context_lost_cnt_after != bank->context_loss_count ||
!context_lost_cnt_after) {
omap_gpio_restore_context(bank);
Restoring context when the context_lost_cnt_after == 0 is clearly
wrong, since this will be true until the first off-mode transition
(which could be never, if off-mode is never enabled.) This check
causes the context to be restored on *every* runtime PM transition.
Before commit 1b1287032 (gpio/omap: fix missing check in
*_runtime_suspend()), this code was never executed in non-OFF mode, so
there were never spurious context restores happening. After that
change though, spurious context restores could happen.
To fix, simply remove the !context_lost_cnt_after check. It is not
needed.
This bug was found when noticing that the smc911x NIC on 3530/Overo
was not working, and git bisect tracked it down to this patch. It
seems that the spurious context restore was causing the smsc911x to
not be properly probed on this platform.
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We do checking for bank->enabled_non_wakeup_gpios in order
to skip redundant operations. Somehow, the check got missed
while doing the cleanup series.
Just to make sure that we do context restore correctly in
*_runtime_resume(), the bank->workaround_enabled check is
moved after context restore. Otherwise, it would prevent
context restore when bank->enabled_non_wakeup_gpios is 0.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add register offsets for GPIO_IRQSTATUS_RAW_0, GPIO_IRQSTATUS_RAW_0
which are present on OMAP4+ processors. Now we can distinguish
conditions applicable to OMAP4,5 and those specific to OMAP24xx
and OMAP3xxx.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Both omap_gpio_suspend() and omap_gpio_resume() does programming
of wakeup_en register.
_gpio_rmw(base, bank->regs->wkup_en, 0xffffffff, 0);
_gpio_rmw(base, bank->regs->wkup_en, bank->context.wake_en, 1);
This is redundant in omap_gpio_suspend() because wakeup_en
register automatically gets initialized in _set_gpio_wakeup()
and set_gpio_trigger() while being called either from
chip.irq_set_wake() or chip.irq_set_type().
This is also redundant in omap_gpio_resume() because wakeup_en
register is programmed in omap_gpio_restore_context() called
which is called from runtime resume callback.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
commit 672e302e3c (ARM: OMAP: use edge/level handlers from generic IRQ
framework) removed retrigger support in favor of using generic IRQ
framework. This patch cleans up some unused remnants of that removal.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There is no more need to have saved_wakeup because bank->context.wake_en
already holds that value. So getting rid of read/write operation associated
with this field.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since we already have bank->context.wake_en to keep track
of gpios which are wakeup enabled, there is no need to have
this field any more.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since we already have context.fallingdetect and context.risingdetect
there is no more need to have these additional fields. Also, getting
rid of extra reads associated with them.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Initialization of irqenable, irqstatus registers is the common
operation done in this function for all OMAP platforms, viz. OMAP1,
OMAP2+. The latter _gpio_rmw()'s which supposedly got introduced
wrongly to take care of OMAP2+ platforms were overwriting initially
programmed OMAP1 value breaking functionality on OMAP1.
Somehow incorrect assumption was made that each _gpio_rmw()'s were
mutually exclusive. On close observation it is found that the first
_gpio_rmw() which is supposedly done to take care of OMAP1 platform
is generic enough and takes care of OMAP2+ platform as well.
Therefore remove the latter _gpio_rmw() to irqenable as they are
redundant now.
Writing to ctrl and debounce_en registers for OMAP2+ platforms are
modified to match the original(pre-cleanup) code where the registers
are initialized with 0. In the cleanup series since we are using
_gpio_rmw(reg, 0, 1), instead of __raw_writel(), we are just reading
and writing the same values to ctrl and debounce_en. This is not an
issue for debounce_en register because it has 0x0 as the default value.
But in the case of ctrl register the default value is 0x2 (GATINGRATIO
= 0x1) so that we end up writing 0x2 instead of intended 0 value.
Therefore changing back to __raw_writel() as this is sufficient for
this case besides simpler to understand.
Also, change irqstatus initalization logic that avoids comparison
with bool, besides making it fit in a single line.
Cc: stable@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In gpio_get(), _get_gpio_datain() and _get_gpio_dataout() get rid of
un-necessary operation to compute gpio mask. The gpio offset passed
to gpio_get() is sufficient to do that.
Here is Russell's original comment:
Can someone explain to me this:
static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
{
void __iomem *reg = bank->base + bank->regs->datain;
return (__raw_readl(reg) & GPIO_BIT(bank, gpio)) != 0;
}
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
void __iomem *reg = bank->base;
int gpio = chip->base + offset;
u32 mask = GPIO_BIT(bank, gpio);
if (gpio_is_input(bank, mask))
return _get_gpio_datain(bank, gpio);
else
return _get_gpio_dataout(bank, gpio);
}
Given that bank->width on OMAP is either 32 or 16, and GPIO numbers for
any GPIO chip are always aligned to 32 or 16, why does this code bother
adding the chips base gpio number and then modulo the width?
Surely this means if - for argument sake - you registered a GPIO chip
with 8 lines followed by one with 16 lines, GPIO0..7 would be chip 0
bit 0..7, GPIO8..15 would be chip 1 bit 8..15, GPIO16..23 would be
chip 1 bit 0..7.
However, if you registered a GPIO chip with 16 lines first, it would
mean GPIO0..15 would be chip 0 bit 0..15, and GPIO16..31 would be
chip 1 bit 0..15.
Surely this kind of behaviour is not intended?
Is there a reason why the bitmask can't just be (1 << offset) where
offset is passed into these functions as GPIO number - chip->base ?
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In _enable_gpio_irqbank() when bank->regs->set_irqenable is TRUE,
gpio_mask can be directly set by writing to set_irqenable register
without overwriting current value. In order to ensure the same is
stored in context.irqenable1, we must avoid overwriting it with
gpio_mask at the end of the function. Instead, update irqenable1
appropriately by OR'ing with gpio_mask.
For the case where bank->regs->set_irqenable is FALSE, irqenable1
can be directly overwritten with 'l' which holds correct computed
value.
if (bank->regs->set_irqenable) {
reg += bank->regs->set_irqenable;
l = gpio_mask;
} else {
reg += bank->regs->irqenable;
l = __raw_readl(reg);
if (bank->regs->irqenable_inv)
l &= ~gpio_mask;
else
l |= gpio_mask;
}
Make similar change for _disable_gpio_irqbank().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap_gpio_runtime_suspend/resume() the context save/restore should
be independent of bank->enabled_non_wakeup_gpios. This was preventing
context restore of GPIO lines which are not wakeup enabled.
Reported-by: Govindraj Raja <govindraj.raja@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There are two functions, _set_gpio_dataout_reg() and _set_gpio_dataout_mask()
which writes to dataout register and the dataout context must be saved.
It is missing in the first function, _set_gpio_dataout_reg(). Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This function should be capable of both enabling and disabling interrupts
based upon the *enable* parameter. Right now the function only enables
the interrupt and *enable* is not used at all. So add the interrupt
disable capability also using the parameter.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The GPIO trigger parameter is of type unsigned.
enum {
IRQ_TYPE_NONE = 0x00000000,
IRQ_TYPE_EDGE_RISING = 0x00000001,
IRQ_TYPE_EDGE_FALLING = 0x00000002,
IRQ_TYPE_EDGE_BOTH = (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING),
IRQ_TYPE_LEVEL_HIGH = 0x00000004,
IRQ_TYPE_LEVEL_LOW = 0x00000008,
IRQ_TYPE_LEVEL_MASK = (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH),
IRQ_TYPE_SENSE_MASK = 0x0000000f,
IRQ_TYPE_PROBE = 0x00000010,
...
};
Even though gpio_irq_type(struct irq_data *d, unsigned type) has the right type
of parameter, the subsequent called functions set_gpio_triggering() and
set_gpio_trigger() wrongly makes it signed integer. Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There are two ways through which wakeup_en register can be programmed
using gpiolib APIs as shown below. It is seen that in the second case
in _set_gpio_wakeup(), even though bank->suspend_wakeup is updated
correctly, its value is not programmed in wakeup_en register. Fix this.
irq_set_type()->gpio_irq_type()->_set_gpio_triggering()->set_gpio_trigger()
irq_set_wake()->gpio_wake_enable()->_set_gpio_wakeup()
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Make omap_mpuio_alloc_gc() __devinit as omap_gpio_chip_init()
is __devinit. Otherwise we get:
WARNING: vmlinux.o(.devinit.text+0xa10): Section mismatch in reference
from the function omap_gpio_chip_init() to the function .init.text:omap_mpuio_alloc_gc()
The function __devinit omap_gpio_chip_init() references
a function __init omap_mpuio_alloc_gc().
If omap_mpuio_alloc_gc is only used by omap_gpio_chip_init then
annotate omap_mpuio_alloc_gc with a matching annotation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While both level- and edge-triggered GPIOs are capable of generating
interrupts, only edge-triggered GPIOs are capable of generating a
module-level wakeup to the PRCM (c.f. 34xx NDA TRM section 25.5.3.2.)
In order to ensure that devices using level-triggered GPIOs as
interrupts can also cause wakeups (e.g. from idle), this patch enables
edge-triggering for wakeup-enabled, level-triggered GPIOs when a GPIO
bank is runtime-suspended (which also happens during idle.)
This fixes a problem found in GPMC-connected network cards with GPIO
interrupts (e.g. smsc911x on Zoom3, Overo, ...) where network booting
with NFSroot was very slow since the GPIO IRQs used by the NIC were
not generating PRCM wakeups, and thus not waking the system from idle.
NOTE: until v3.3, this boot-time problem was somewhat masked because
the UART init prevented WFI during boot until the full serial driver
was available. Preventing WFI allowed regular GPIO interrupts to fire
and this problem was not seen. After the UART runtime PM cleanups, we
no longer avoid WFI during boot, so GPIO IRQs that were not causing
wakeups resulted in very slow IRQ response times.
Tested on platforms using level-triggered GPIOs for network IRQs using
the SMSC911x NIC: 3530/Overo and 3630/Zoom3.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The driver is still relying on internal OMAP IRQ defines that
are not relevant anymore if OMAP is built with SPARSE_IRQ.
Replace the defines with the proper IRQ base number.
Clean some comment style issue.
Remove some hidden and ugly cpu_class_is_omap1() inside the
gpio header.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Adapt the GPIO driver to retrieve information from a DT file.
Allocate the irq_base dynamically and rename bank->virtual_irq_start
to bank->irq_base.
Change irq_base type to int instead of u16 to match irq_alloc_descs
output.
Add documentation for GPIO properties specific to OMAP.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Replace the regular kzalloc and ioremap with the devm_ equivalent
to simplify error handling.
Add the missing devm_request_mem_region to reserve the region used
by the driver.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
The driver does not need anymore any id to identify the GPIO instance.
Remove every occurence of the bank->id inside the driver.
Remove two trailing spaces.
Add a dev variable for better readability in probe.
Remove unused variable bank->pbase.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
GPIO IP revisions such as those used in OMAP4 have a set_dataout
while the previous revisions used a single dataout register.
Depending on what is available restore the dataout settings
to the right register.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setup the dataout register before restoring OE. This is to make
sure that we have valid data in dataout register which would be
made available in output pins as soon as OE is enabled. Else,
there is risk of unknown data getting out into gpio pins.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setup the interrupt enable registers only after we have configured the
required edge and required configurations, not before, to prevent
spurious events as part of restore routine.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
GPIO debounce registers need to be saved and restored for proper functioning
of driver.
Signed-off-by: Nishanth Menon <nm@ti.com>
tarun.kanti@ti.com: Debounce context save is moved to _set_gpio_debounce()
as part of dynamic context save to remove overhead.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Context is now saved dynamically in respective functions whenever and
whichever registers are modified. This avoid overhead of saving all
registers context in the runtime suspend callback.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Enable debounce clock before writing/reading debounce registers.
Disable the clock at the end so that it is synchronized with the
pm_runtime_get/put_sync calls.
Enable debounce clock per module. This call is mandatory because
in omap_gpio_request() when *_runtime_get_sync() is called,
_gpio_dbck_enable() within runtime callbck fails to turn on dbck
because dbck_enable_mask used within _gpio_dbck_enable() is still
not initialized at that point. Therefore we have to enable dbck here.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The dbck_enable_mask indicates which all GPIOs within a bank have debounce
enabled and dbck is enabled/disabled based upon this. But there is no
mechanism to track the dbck state. In order to manage the dbck state we need
additional flag and logic so that turning off/on dbck is synchronized with
pm_runtime_put/get_sync calls.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since *_prepare_for_idle() and *_resume_after_idle() are called
with interrupts disabled they should be kept as simple as possible.
So, moving most of the stuff to *_runtime_suspend/resume() callbacks.
To avoid invalid context restore happening in *_runtime_resume()
callback as a result of *_get_sync() call in *_gpio_probe(), update
bank->context_loss_count. This would make context restore condition
check false in the callback and skip restore until further
initialization take place. The workaround_enabled static variable
is now a member of struct gpio_bank.
Unlike most GPIO registers the OE has 0xffffffff as the default value.
To make sure invalid context is not restored, updating the OE context
with default value.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There is no need to operate on all the banks every time the function is called.
Just operate on the current bank passed by the framework.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Call runtime pm APIs pm_runtime_get_sync() and pm_runtime_put()
for enabling/disabling clocks appropriately. Remove syscore_ops and
instead use SET_RUNTIME_PM_OPS macro.
There is no more need to call omap_device_disable_idle_on_suspend
since driver is PM runtime adapted now.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.
mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove un-necessary bit masking. Since the register are 4 byte aligned
and readl would work as is. The 'enabled' mask is already taking care
to mask for bank width.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use regs->pinctrl field instead of using the macro OMAP1510_GPIO_PIN_CONTROL
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With register offsets now defined for respective OMAP versions we can get rid
of cpu_class_* checks. This function now has common initialization code for
all OMAP versions. Initialization specific to OMAP16xx has been moved within
omap16xx_gpio_init().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Getting rid of ifdefs within the function by adding register offset intctrl
and associating OMAPXXXX_GPIO_INT_CONTROL in respective SoC specific files.
Also, use wkup_status register consistently instead of referring to wakeup
clear and wakeup set register offsets. Get rid of cpu_is_xxxx checks in
set_gpio_trigger() using irqctrl.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently gpio_context array used to save gpio bank's context, is used only for
OMAP3 architecture. Move gpio_context as part of gpio_bank structure so that it
can be specific to each gpio bank and can be used for any OMAP architecture
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.
For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: pca953x: propagate the errno from the chip_init functions
gpio: pca953x: remove unneeded check for chip type
gpio/omap: check return value from irq_alloc_generic_chip
gpio/omap: replace MOD_REG_BIT macro with static inline
With commit f64ad1a0e2, "gpio/omap: cleanup _set_gpio_wakeup(), remove
ifdefs", access to build time conditionally omitted 'suspend_wakeup'
member of the 'gpio_bank' structure has been placed unconditionally in
function _set_gpio_wakeup(), which is always built. This resulted in the
driver compilation broken for certain OMAP1, i.e., non-OMAP16xx,
configurations.
Really required or not in previously excluded cases, define this
structure member unconditionally as a fix.
Tested with a custom OMAP1510 only configuration.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Ensure return value of irq_alloc_generic_chip() is checked before continuing
on to use it.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This macro is ugly and confusing, especially since it passes in most
arguments, but uses an implied 'base' from the caller.
Replace it with an equivalent static inline.
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
Remove cpu_is_* checks from gpio_show_revision() by passing in the
revision address offset from platform data. SoCs with no revision
register (15xx, 7xx, and all MPUIOs) use -1 (actually, USHRT_MAX) to
signify no register.
While here, all GPIO banks are assumed to be the same revision, so fix
show_revision() to only show the revision for the first bank it finds.
This removes duplicate GPIO revision prints during boot.
Thanks to Charulatha V <charu@ti.com> for finding/fixing a few -1s
that were missed in the original patch.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Make _set_gpio_wakeup() generic by removing ifdefs. Code for the
various SoCs/bank-methods was already the same, except for the
non-wakeup GPIO checking. But that flag is set on a per-SoC basis, so
can be used for all SoCs.
While here, use dev_err() and remove GPIO bank calculation assumption
based on subtracting bank pointers.
Signed-off-by: Kevin Hilman <khilman@ti.com>
These functions are useless. They are only called in a few places,
and where they are called, the GPIO has already been converted from an
IRQ or masked, so these functions will never fail.
Signed-off-by: Kevin Hilman <khilman@ti.com>
MPUIO banks have their own dedicated IRQ chip interface, separate from
the "normal" GPIO banks. Convert the MPUIO IRQ chip over to using
the new generic IRQ chip interface.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup GPIO IRQ enable/disable handling by removing SoC-specific
Also split enable/disable IRQ into separate functions for better
readability and also facilitate potentially moving to generic irq_chip
in the future.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup IRQ status handling by passing IRQ status register offsets
via platform data.
Cleans up clearing of GPIO IRQ status and GPIO ISR handler.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add register offset fields to GPIO platform_data for registers.
This patch adds registers that control direction, input and output
data. Using these register offsets in the common driver allows
removal of #ifdefs and greatly improves readability.
Also create dedicated data out functions: one for banks with dedicated
set/clear registers, and another for banks with a single mask
register.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The get_gpio_index() function, littered with cpu_is_* checks can be easily
replaced by using bitops based on the GPIO bank width. Do so.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Rather than having a file-global bank_width variable, move it into
struct gpio_bank so it can be bank-specific. Note the bank width
is already passed per-bank via platform_data, so current code would
be incorrect if any banks had different width.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the OMAP1 #ifdef and MPUIO special case for _clear_gpio_irqbank()
The MPUIOs do not need a register access to ack/clear the IRQ status,
since reading the IRQ status clears it. In addition, the MPUIO
irq_chip has an empty ack method, so _clear_gpio_irqbank() is never
used for MPUIOs.
Signed-off-by: Kevin Hilman <khilman@ti.com>
In commit 78a1a6d341 (ARM: OMAP4: Update
the GPIO support) braces were mistakenly added to included the
register read-back inside the cpu_is_* checking.
Remove the braces, ensuring that a register read-back is done, even
when the IRQSTATUS2 register is not written.
Note that the register read-back might be IRQSTATUS1 or IRQSTATUS2
depending on the CPU, but a read-back of any register in that region
will cause a flush of the posted writes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
If gpio pins from bank[2-5] are marked as wakeup enable and if the wake is
through gpio IO pad wakeup, then that wakeup gpio interrupt is lost.
In the current implementation, GPIO driver stores the context of DATAIN of
all the gpio in the bank. During GPIO resuming, it checks DATAIN with wakeup
enabled pins of gpio bank. If there is status change, then manually toggle
GPIO_LEVELDETECT to generate pseudo interrupt.
Reported-by: Philippe Mazet <p-mazet@ti.com>
Tested-by: Philippe Mazet <p-mazet@ti.com>
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
_set_gpio_triggering uses read-modify-write on bank registers,
lock bank->lock around all calls to it to prevent register
corruption if two cpus access gpios in the same bank at the
same time.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setting the IRQWAKEN bit was overwriting previous IRQWAKEN bits,
causing only the last bit set to take effect, resulting in lost
wakeups when the GPIO controller is in idle.
Replace direct writes to IRQWAKEN with MOD_REG_BIT calls to
perform a read-modify-write on the register.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
WARNING: arch/arm/plat-omap/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_chip_init()
The function __devinit omap_gpio_probe() references
a function __init omap_gpio_chip_init().
If omap_gpio_chip_init is only used by omap_gpio_probe then
annotate omap_gpio_chip_init with a matching annotation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Chen Gang
Linus Torvalds
Bill Pemberton
Jon Hunter
Tobias Klauser
Tony Lindgren
Uwe Kleine-König
Tarun Kanti DebBarma
Grazvydas Ignotas
Kevin Hilman
Benoit Cousson
Nishanth Menon
Charulatha V
Janusz Krzysztofik
Todd Poynor
Russell King
Ambresh K
Colin Cross