Currently the following errors are seen:
[ 14.015056] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.321093] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.411681] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.456281] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 30.527106] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 36.596900] mc13xxx 0-0008: Failed to read IRQ status: -6
Also when reading the interrupts via 'cat /proc/interrupts' the
PMIC GPIO interrupt counter does not stop increasing.
The reason for the storm of interrupts is that the PUS field of
register IOMUXC_SW_PAD_CTL_PAD_CSI0_DAT5 is currently configured as:
10 : 100k pullup
and the PMIC interrupt is being registered as IRQ_TYPE_LEVEL_HIGH type,
which is the correct type as per the MC34708 datasheet.
Use the default power on value for the IOMUX, which sets PUS field as:
00: 360k pull down
This prevents the spurious PMIC interrupts from happening.
Commit e1ffceb078 ("ARM: imx53: qsrb: fix PMIC interrupt level")
correctly described the irq type as IRQ_TYPE_LEVEL_HIGH, but
missed to update the IOMUX of the PMIC GPIO as pull down.
Fixes: e1ffceb078 ("ARM: imx53: qsrb: fix PMIC interrupt level")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Quoting Philipp Zabel:
"Since this regulator is used as the TVDAC analog power supply, this
range should at least be limited to the analog power supply range of the
TVDAC, listed in Table 74-9. of the i.MX53 reference manual (2.5-2.75V).
But since the nominal voltage is 2.75V, which was used to determine the
analog gain that is supposed to result in the necessary 0.7V
peak-to-peak amplitude on the VGA output, I'd say we should just fix the
voltage to 2750000 here."
, so limit the TVDAC analog power supply as suggested.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx53-qsb the TVE DAC regulator comes from:
- LDO7 on the board with the Dialog DA9052 PMIC
- VDAC on the board with the MC34708 PMIC
Pass them in the 'dac-supply' node.
While at it, remove the 'regulator-always-on/regulator-boot-on'
properties as the TVE driver will properly handle it.
Tested on a imx53-qsb board with a Dialog DA9052 PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MC34708 PMIC interrupt level is active high, but was set to
active low in the devicetree, probably as a result of a copy and
paste error from the QSB board.
This caused IRQ storms and led to the kernel disabling the PMIC
interrupt.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Both imx53-qsb and imx53-qsrb don't have external pull-up resistors
on the I2C1 SCL and SDA lines populated. Select open-drain mode and
enable the internal pull-up for both.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The "Start-R QSB" has a different PMIC than the older "Start QSB".
Add a new devicetree for the Start-R.
They both could use the same DT, as both PMICs (the dialog and the mc34708)
have different i2c addresses and could coexist in the same DT without any
errors. But once phandles are used, this will get messy.
The pmic nodes are based on an earlier patch
[PATCH] arm: imx53-qsb: Add Ripley driver DT nodes
from
Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
which apparently got lost/abandoned.
I added phandles/newlines and changed the node name from ripley to mc34708.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fabio Estevam
Lucas Stach
Fabio Estevam
Steffen Trumtrar