Граф коммитов

11 Коммитов

Автор SHA1 Сообщение Дата
Rob Herring 8dccafaa28 arm: dts: fix unit-address leading 0s
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:

perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'

Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-10-20 00:37:54 +02:00
Oleksij Rempel e8ebecf60f ARM: dts: imx6: RIoTboard provide gpio-line-names
gpio-line-names may help to make work with GPIOs from user space easier.
Following examples are provided with libgpiod
https://github.com/brgl/libgpiod :
|# Toggle a GPIO by name, then wait for the user to press ENTER.
|$ gpioset --mode=wait `gpiofind "USR-LED-2"`=1
|# Pause execution until a single event of any type occurs. Don't print
|# anything. Find the line by name.
|$ gpiomon --num-events=1 --silent `gpiofind "USR-IN"`

Used names was taken from RIoTboard schematics, version 1 (2013.12.07).

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-07-25 17:09:14 +08:00
Fabio Estevam 12de44f55d ARM: dts: imx: Fix Ethernet PHY reset polarity
The FEC driver ignores the GPIO polarity from 'phy-reset-gpios' and
considers that the Ethernet PHY is active low, unless the
property 'phy-reset-active-high' is present.

Fix the device tree description by explicitly passing the
'GPIO_ACTIVE_LOW' flag to the 'phy-reset-gpios' property.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-06-05 23:24:13 +08:00
Jagan Teki 4631170793 ARM: dts: imx: Fix "ERROR: code indent should use tabs where possible"
Fixed code indent tabs in respetcive imx23, imx51, imx53, imx6dl, imx6q
and imx6sx dtsi and dts files.

Signed-off-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-11-02 22:43:56 +08:00
Uwe Kleine-König c007b3a697 ARM: dts: imx6qdl: don't configure reserved pad settings
Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.

Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-08-09 11:40:40 +08:00
Lucas Stach a28eeb43ee ARM: dts: imx6: tag boards that have the HW workaround for ERR006687
Add the DT property to all boards that have the hardware workaround
for erratum ERR006687 present. This allows the CPUidle driver to use
the deep idle states, even if the FEC is active.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-06-11 17:03:44 +08:00
Fabio Estevam b26a68c1fb ARM: dts: imx6: Do not hardcode the CLKO clock
Using "IMX6QDL_CLK_CKO" for the clock is easier to read instead of
the hardcoded clock number.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-27 10:55:50 +08:00
Dong Aisheng 89c1a8cf63 dts: imx6: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().

Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-07-24 10:18:35 +02:00
Iain Paton cb9456b538 ARM: dts: imx6: RIoTboard explicitly define pad settings
Instead of relying on defaults or bootloader settings, explicitly define
all pad settings.

This resolves reported issues of no analogue audio output.

Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-18 16:49:46 +08:00
Markus Pargmann 9eb0e5f9b2 ARM: dts: imx: remove ssi fsl,mode for audio cards
The DAI mode is and should be configured by the sound card driver as
codec and ssi have to be in the right modes to communicate with each
other. It is possible to operate the ssi unit or the codec in master mode,
sometimes even on the same board in different configurations.

With the latest changes in the fsl-ssi driver, the 'fsl,mode' property
is only handled as a fallback property. If the sound card sets the DAI
mode correctly, this fallback configuration is dropped.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-18 16:49:37 +08:00
Iain Paton ec55b15087 ARM: dts: imx6: add new board RIoTboard
add element14s RIoTboard http://www.riotboard.org which is an i.MX6Solo
based design targeted at makers.

Signed-off-by: Iain Paton<ipaton0@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16 23:02:12 +08:00