As explained here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocol drivers cannot depend on symbols exported by switch
drivers, because this creates a circular dependency that breaks module
autoloading.
The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function
exported by the common ocelot switch lib. This function looks at
OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the
DSA tag, for PTP timestamping (the command: one-step/two-step, and the
TX timestamp identifier).
None of that requires deep insight into the driver, it is quite
stateless, as it only depends upon the skb->cb. So let's make it a
static inline function and put it in include/linux/dsa/ocelot.h, a
file that despite its name is used by the ocelot switch driver for
populating the injection header too - since commit 40d3f295b5 ("net:
mscc: ocelot: use common tag parsing code with DSA").
With that function declared as static inline, its body is expanded
inside each call site, so the dependency is broken and the DSA tagger
can be built without the switch library, upon which the felix driver
depends.
Fixes: 39e5308b32 ("net: mscc: ocelot: support PTP Sync one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sad reality is that when a PTP frame with a TX timestamping request
is transmitted, it isn't guaranteed that it will make it all the way to
the wire (due to congestion inside the switch), and that a timestamp
will be taken by the hardware and placed in the timestamp FIFO where an
IRQ will be raised for it.
The implication is that if enough PTP frames are silently dropped by the
hardware such that the timestamp ID has rolled over, it is possible to
match a timestamp to an old skb.
Furthermore, nobody will match on the real skb corresponding to this
timestamp, since we stupidly matched on a previous one that was stale in
the queue, and stopped there.
So PTP timestamping will be broken and there will be no way to recover.
It looks like the hardware parses the sequenceID from the PTP header,
and also provides that metadata for each timestamp. The driver currently
ignores this, but it shouldn't.
As an extra resiliency measure, do the following:
- check whether the PTP sequenceID also matches between the skb and the
timestamp, treat the skb as stale otherwise and free it
- if we see a stale skb, don't stop there and try to match an skb one
more time, chances are there's one more skb in the queue with the same
timestamp ID, otherwise we wouldn't have ever found the stale one (it
is by timestamp ID that we matched it).
While this does not prevent PTP packet drops, it at least prevents
the catastrophic consequences of incorrect timestamp matching.
Since we already call ptp_classify_raw in the TX path, save the result
in the skb->cb of the clone, and just use that result in the interrupt
code path.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It appears that Ocelot switches cannot timestamp non-PTP frames,
I tested this using the isochron program at:
https://github.com/vladimiroltean/tsn-scripts
with the result that the driver increments the ocelot_port->ts_id
counter as expected, puts it in the REW_OP, but the hardware seems to
not timestamp these packets at all, since no IRQ is emitted.
Therefore check whether we are sending PTP frames, and refuse to
populate REW_OP otherwise.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When skb_match is NULL, it means we received a PTP IRQ for a timestamp
ID that the kernel has no idea about, since there is no skb in the
timestamping queue with that timestamp ID.
This is a grave error and not something to just "continue" over.
So print a big warning in case this happens.
Also, move the check above ocelot_get_hwtimestamp(), there is no point
in reading the full 64-bit current PTP time if we're not going to do
anything with it anyway for this skb.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.
This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).
I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present, there is a problem when user space bombards a port with PTP
event frames which have TX timestamping requests (or when a tc-taprio
offload is installed on a port, which delays the TX timestamps by a
significant amount of time). The driver will happily roll over the 2-bit
timestamp ID and this will cause incorrect matches between an skb and
the TX timestamp collected from the FIFO.
The Ocelot switches have a 6-bit PTP timestamp identifier, and the value
63 is reserved, so that leaves identifiers 0-62 to be used.
The timestamp identifiers are selected by the REW_OP packet field, and
are actually shared between CPU-injected frames and frames which match a
VCAP IS2 rule that modifies the REW_OP. The hardware supports
partitioning between the two uses of the REW_OP field through the
PTP_ID_LOW and PTP_ID_HIGH registers, and by default reserves the PTP
IDs 0-3 for CPU-injected traffic and the rest for VCAP IS2.
The driver does not use VCAP IS2 to set REW_OP for 2-step timestamping,
and it also writes 0xffffffff to both PTP_ID_HIGH and PTP_ID_LOW in
ocelot_init_timestamp() which makes all timestamp identifiers available
to CPU injection.
Therefore, we can make use of all 63 timestamp identifiers, which should
allow more timestampable packets to be in flight on each port. This is
only part of the solution, more issues will be addressed in future changes.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes: 994d2cbb08 ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes: 566b18c8b7 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Flip the sign of a return value check, thereby suppressing the following
spurious error:
port 2 failed to notify DSA_NOTIFIER_BRIDGE_LEAVE: -EOPNOTSUPP
... which is emitted when removing an unoffloaded DSA switch port from a
bridge.
Fixes: d371b7c92d ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211012112730.3429157-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On R-Car D3 and E3, the LVDS encoders provide the pixel clock to the DU,
even when LVDS outputs are not used. For this reason, the rcar-lvds
driver probes successfully on those platforms even if no further bridge
or panel is connected to the LVDS output, in order to provide the
rcar_lvds_clk_enable() and rcar_lvds_clk_disable() functions to the DU
driver.
If an LVDS output isn't connected, trying to create a DRM connector for
the output will fail. Fix this by skipping connector creation in that
case, and also skip creation of the DRM encoder as there's no point in
an encoder without a connector.
Fixes: e9e056949c ("drm: rcar-du: lvds: Convert to DRM panel bridge helper")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 187502afe8)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 846d6da1fc ("net/mlx5e: Fix division by 0 in
mlx5e_select_queue") makes mlx5e_build_nic_params assign a non-zero
initial value to priv->num_tc_x_num_ch, so that mlx5e_select_queue
doesn't fail with division by 0 if called before the first activation of
channels. However, the initialization flow of representors doesn't call
mlx5e_build_nic_params, so this bug can still happen with representors.
This commit fixes the bug by adding the missing assignment to
mlx5e_build_rep_params.
Fixes: 846d6da1fc ("net/mlx5e: Fix division by 0 in mlx5e_select_queue")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Due to current HW arch limitations, RX-FCS (scattering FCS frame field
to software) and RX-port-timestamp (improved timestamp accuracy on the
receive side) can't work together.
RX-port-timestamp is not controlled by the user and it is enabled by
default when supported by the HW/FW.
This patch sets RX-port-timestamp opposite to RX-FCS configuration.
Fixes: 102722fc68 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Before this patch, mlx5 representors advertised the
NETIF_F_VLAN_CHALLENGED bit, this could lead to missing features when
using reps with vxlan/bridge and maybe other virtual interfaces,
when such interfaces inherit this bit and block vlan usage in their
topology.
Example:
$ip link add dev bridge type bridge
# add representor interface to the bridge
$ip link set dev pf0hpf master
$ip link add link bridge name vlan10 type vlan id 10 protocol 802.1q
Error: 8021q: VLANs not supported on device.
Reps are perfectly capable of handling vlan traffic, although they don't
implement vlan_{add,kill}_vid ndos, hence, remove
NETIF_F_VLAN_CHALLENGED advertisement.
Fixes: cb67b83292 ("net/mlx5e: Introduce SRIOV VF representors")
Reported-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Do not allow configurations of MQPRIO channel mode that do not
fully define and utilize the channels txqs.
Fixes: ec60c4581b ("net/mlx5e: Support MQPRIO channel mode")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The device advertises 8 formats, but only a rate of 48kHz is honored
by the hardware and 24 bits give chopped audio, so only report the
one working combination. This fixes out-of-the-box audio experience
with PipeWire which otherwise attempts to choose S24_3LE (while
PulseAudio defaulted to S16_LE).
Signed-off-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211012200906.3492-1-hahnjo@hahnjo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Second (small) set of pdx86 fixes for 5.15.
The following is an automated git shortlog grouped by driver:
amd-pmc:
- Add alternative acpi id for PMC controller
dell:
- Make DELL_WMI_PRIVACY depend on DELL_WMI
gigabyte-wmi:
- add support for B550 AORUS ELITE AX V2
int1092:
- Fix non sequential device mode handling
intel_scu_ipc:
- Update timeout value in comment
- Increase virtual timeout to 10s
- Fix busy loop expiry time
intel_skl_int3472:
- Correct null check
platform/mellanox:
- mlxreg-io: Fix read access of n-bytes size attributes
- mlxreg-io: Fix argument base in kstrtou32() call
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmFlpcwUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9z1Owf/Xc2esJBtGaVww+A8DlXix8qzE31q
y0KgnBYj0NSU5FBkkcYIbTW2r8gAXmMryfKk9meguYTN6U6lyzOT4kty2Ct9TUSs
XpD1OwIIyUj07ptFlkGezGMHsqAMcZPLXDF0tqwxvrUUwndlh7Ead+3+Gc8o4fnb
6jClpVRIZ/NwtXmnq6oXqaD5zS+eFeTo6G+N4WOVEDJa0Z+2WR+HJkYlxqxVfAyW
l/MPoCM+EGz1bTSw5XRiQurv+aX7bEZOac/0cB038ANs/WRAelm7SQ4HhzAFPz+i
+UxZjFPxb2mwg02LOGvgBWlYW1yoDTUriuvsLL0wqSEuS5vGIrrD8lRPrQ==
=9FcO
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"A second (small) set of pdx86 bug-fixes and new hardware ids for 5.15"
* tag 'platform-drivers-x86-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: int1092: Fix non sequential device mode handling
platform/x86: intel_skl_int3472: Correct null check
platform/x86: gigabyte-wmi: add support for B550 AORUS ELITE AX V2
platform/x86: amd-pmc: Add alternative acpi id for PMC controller
platform/x86: intel_scu_ipc: Update timeout value in comment
platform/x86: intel_scu_ipc: Increase virtual timeout to 10s
platform/x86: intel_scu_ipc: Fix busy loop expiry time
platform/x86: dell: Make DELL_WMI_PRIVACY depend on DELL_WMI
platform/mellanox: mlxreg-io: Fix read access of n-bytes size attributes
platform/mellanox: mlxreg-io: Fix argument base in kstrtou32() call
DM uses blk-mq's quiesce/unquiesce to stop/start device mapper queue.
But blk-mq's unquiesce may come from outside events, such as elevator
switch, updating nr_requests or others, and request may come during
suspend, so simply ask for blk-mq to requeue it.
Fixes one kernel panic issue when running updating nr_requests and
dm-mpath suspend/resume stress test.
Cc: stable@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Don't populate the read-only array descs on the stack but instead it
static and add extra const. Also makes the object code smaller by 66
bytes:
Before:
text data bss dec hex filename
42382 11140 512 54034 d312 ./drivers/md/dm-clone-target.o
After:
text data bss dec hex filename
42220 11236 512 53968 d2d0 ./drivers/md/dm-clone-target.o
(gcc version 11.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Without FEC, dm-verity won't call verity_handle_err() when I/O fails,
but with FEC enabled, it currently does even if an I/O error has
occurred.
If there is an I/O error and FEC correction fails, return the error
instead of calling verity_handle_err() again.
Suggested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Akilesh Kailash <akailash@google.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix modpost Section mismatch error in next_platform_timer().
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e60): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e64): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
make[1]: *** [scripts/Makefile.modpost:59: vmlinux.symvers] Error 1
make[1]: *** Deleting file 'vmlinux.symvers'
make: *** [Makefile:1176: vmlinux] Error 2
[...]
Fixes: a712c3ed9b ("acpi/arm64: Add memory-mapped timer support in GTDT driver")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20210823092526.2407526-1-liu.yun@linux.dev
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
These variables are printed on the error path if match_int() fails so
they have to be initialized.
Fixes: 2958a995ed ("block/rnbd-clt: Support polling mode for IO latency optimization")
Fixes: 1eb54f8f5d ("block/rnbd: client: sysfs interface functions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Gioh Kim <gi-oh.kim@ionos.com>
Link: https://lore.kernel.org/r/20211012084443.GA31472@kili
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A series of devicetree fixes for the Raspberry Pi 4:
- Fix VEC reg address
- Fix MDIO address/size cells
- Fix regulator states
- Fix PCIe address formatting
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
dtbs_check currently complains that:
arch/arm/boot/dts/bcm2711-rpi-4-b.dts:220.10-231.4: Warning
(pci_device_reg): /scb/pcie@7d500000/pci@1,0: PCI unit address format
error, expected "0,0"
Unsurprisingly pci@0,0 is the right address, as illustrated by its reg
property:
&pcie0 {
pci@0,0 {
/*
* As defined in the IEEE Std 1275-1994 document,
* reg is a five-cell address encoded as (phys.hi
* phys.mid phys.lo size.hi size.lo). phys.hi
* should contain the device's BDF as 0b00000000
* bbbbbbbb dddddfff 00000000. The other cells
* should be zero.
*/
reg = <0 0 0 0 0>;
};
};
The device is clearly 0. So fix it.
Also add a missing 'device_type = "pci"'.
Fixes: 258f92d2f8 ("ARM: dts: bcm2711: Add reset controller to xHCI node")
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210831125843.1233488-1-nsaenzju@redhat.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
The snd_hdac_bus_reset_link() contains logic to clear STATESTS register
before performing controller reset. This code dates back to an old
bugfix in commit e8a7f136f5 ("[ALSA] hda-intel - Improve HD-audio
codec probing robustness"). Originally the code was added to
azx_reset().
The code was moved around in commit a41d122449 ("ALSA: hda - Embed bus
into controller object") and ended up to snd_hdac_bus_reset_link() and
called primarily via snd_hdac_bus_init_chip().
The logic to clear STATESTS is correct when snd_hdac_bus_init_chip() is
called when controller is not in reset. In this case, STATESTS can be
cleared. This can be useful e.g. when forcing a controller reset to retry
codec probe. A normal non-power-on reset will not clear the bits.
However, this old logic is problematic when controller is already in
reset. The HDA specification states that controller must be taken out of
reset before writing to registers other than GCTL.CRST (1.0a spec,
3.3.7). The write to STATESTS in snd_hdac_bus_reset_link() will be lost
if the controller is already in reset per the HDA specification mentioned.
This has been harmless on older hardware. On newer generation of Intel
PCIe based HDA controllers, if configured to report issues, this write
will emit an unsupported request error. If ACPI Platform Error Interface
(APEI) is enabled in kernel, this will end up to kernel log.
Fix the code in snd_hdac_bus_reset_link() to only clear the STATESTS if
the function is called when controller is not in reset. Otherwise
clearing the bits is not possible and should be skipped.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211012142935.3731820-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to define the codec pin 0x1b to be the mic, but somehow
the mic doesn't support hot plugging detection, and Windows also has
this issue, so we set it to phantom headset-mic.
Also the determine_headset_type() often returns the omtp type by a
mistake when we plug a ctia headset, this makes the mic can't record
sound at all. Because most of the headset are ctia type nowadays and
some machines have the fixed ctia type audio jack, it is possible this
machine has the fixed ctia jack too. Here we set this mic jack to
fixed ctia type, this could avoid the mic type detection mistake and
make the ctia headset work stable.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214537
Reported-and-tested-by: msd <msd.mmq@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20211012114748.5238-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When OP-TEE driver is built as a module, OP-TEE client devices
registered on TEE bus during probe should be unregistered during
optee_remove. So implement optee_unregister_devices() accordingly.
Fixes: c3fa24af92 ("tee: optee: add TEE bus device enumeration support")
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Commit 4dd0d5c33c ("ice: add lock around Tx timestamp tracker flush")
added a lock around the Tx timestamp tracker flow which is used to
cleanup any left over SKBs and prepare for device removal.
This lock is problematic because it is being held around a call to
ice_clear_phy_tstamp. The clear function takes a mutex to send a PHY
write command to firmware. This could lead to a deadlock if the mutex
actually sleeps, and causes the following warning on a kernel with
preemption debugging enabled:
[ 715.419426] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:573
[ 715.427900] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 3100, name: rmmod
[ 715.435652] INFO: lockdep is turned off.
[ 715.439591] Preemption disabled at:
[ 715.439594] [<0000000000000000>] 0x0
[ 715.446678] CPU: 52 PID: 3100 Comm: rmmod Tainted: G W OE 5.15.0-rc4+ #42 bdd7ec3018e725f159ca0d372ce8c2c0e784891c
[ 715.458058] Hardware name: Intel Corporation S2600STQ/S2600STQ, BIOS SE5C620.86B.02.01.0010.010620200716 01/06/2020
[ 715.468483] Call Trace:
[ 715.470940] dump_stack_lvl+0x6a/0x9a
[ 715.474613] ___might_sleep.cold+0x224/0x26a
[ 715.478895] __mutex_lock+0xb3/0x1440
[ 715.482569] ? stack_depot_save+0x378/0x500
[ 715.486763] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.494979] ? kfree+0xc1/0x520
[ 715.498128] ? mutex_lock_io_nested+0x12a0/0x12a0
[ 715.502837] ? kasan_set_free_info+0x20/0x30
[ 715.507110] ? __kasan_slab_free+0x10b/0x140
[ 715.511385] ? slab_free_freelist_hook+0xc7/0x220
[ 715.516092] ? kfree+0xc1/0x520
[ 715.519235] ? ice_deinit_lag+0x16c/0x220 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.527359] ? ice_remove+0x1cf/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.535133] ? pci_device_remove+0xab/0x1d0
[ 715.539318] ? __device_release_driver+0x35b/0x690
[ 715.544110] ? driver_detach+0x214/0x2f0
[ 715.548035] ? bus_remove_driver+0x11d/0x2f0
[ 715.552309] ? pci_unregister_driver+0x26/0x250
[ 715.556840] ? ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.564799] ? __do_sys_delete_module.constprop.0+0x2d8/0x4e0
[ 715.570554] ? do_syscall_64+0x3b/0x90
[ 715.574303] ? entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 715.579529] ? start_flush_work+0x542/0x8f0
[ 715.583719] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.591923] ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.599960] ? wait_for_completion_io+0x250/0x250
[ 715.604662] ? lock_acquire+0x196/0x200
[ 715.608504] ? do_raw_spin_trylock+0xa5/0x160
[ 715.612864] ice_sbq_rw_reg+0x1e6/0x2f0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.620813] ? ice_reset+0x130/0x130 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.628497] ? __debug_check_no_obj_freed+0x1e8/0x3c0
[ 715.633550] ? trace_hardirqs_on+0x1c/0x130
[ 715.637748] ice_write_phy_reg_e810+0x70/0xf0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.646220] ? do_raw_spin_trylock+0xa5/0x160
[ 715.650581] ? ice_ptp_release+0x910/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.658797] ? ice_ptp_release+0x255/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.667013] ice_clear_phy_tstamp+0x2c/0x110 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.675403] ice_ptp_release+0x408/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.683440] ice_remove+0x560/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.691037] ? _raw_spin_unlock_irqrestore+0x46/0x73
[ 715.696005] pci_device_remove+0xab/0x1d0
[ 715.700018] __device_release_driver+0x35b/0x690
[ 715.704637] driver_detach+0x214/0x2f0
[ 715.708389] bus_remove_driver+0x11d/0x2f0
[ 715.712489] pci_unregister_driver+0x26/0x250
[ 715.716857] ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.724637] __do_sys_delete_module.constprop.0+0x2d8/0x4e0
[ 715.730210] ? free_module+0x6d0/0x6d0
[ 715.733963] ? task_work_run+0xe1/0x170
[ 715.737803] ? exit_to_user_mode_loop+0x17f/0x1d0
[ 715.742509] ? rcu_read_lock_sched_held+0x12/0x80
[ 715.747215] ? trace_hardirqs_on+0x1c/0x130
[ 715.751401] do_syscall_64+0x3b/0x90
[ 715.754981] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 715.760033] RIP: 0033:0x7f4dfe59000b
[ 715.763612] Code: 73 01 c3 48 8b 0d 6d 1e 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 1e 0c 00 f7 d8 64 89 01 48
[ 715.782357] RSP: 002b:00007ffe8c891708 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ 715.789923] RAX: ffffffffffffffda RBX: 00005558a20468b0 RCX: 00007f4dfe59000b
[ 715.797054] RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005558a2046918
[ 715.804189] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 715.811319] R10: 00007f4dfe603ac0 R11: 0000000000000206 R12: 00007ffe8c891940
[ 715.818455] R13: 00007ffe8c8920a3 R14: 00005558a20462a0 R15: 00005558a20468b0
Notice that this is the only case where we use the lock in this way. In
the cleanup kthread and work kthread the lock is only taken around the
bit accesses. This was done intentionally to avoid this kind of issue.
The way the lock is used, we only protect ordering of bit sets vs bit
clears. The Tx writers in the hot path don't need to be protected
against the entire kthread loop. The Tx queues threads only need to
ensure that they do not re-use an index that is currently in use. The
cleanup loop does not need to block all new set bits, since it will
re-queue itself if new timestamps are present.
Fix the tracker flow so that it uses the same flow as the standard
cleanup thread. In addition, ensure the in_use bitmap actually gets
cleared properly.
This fixes the warning and also avoids the potential deadlock that might
have occurred otherwise.
Fixes: 4dd0d5c33c ("ice: add lock around Tx timestamp tracker flush")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two problems found in the strrchr() implementation for s390
architectures: evaluate empty strings (return the string address instead of
NULL, if '\0' is passed as second argument); evaluate the first character
of non-empty strings (the current implementation stops at the second).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reported-by: Heiko Carstens <hca@linux.ibm.com> (incorrect behavior with empty strings)
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Link: https://lore.kernel.org/r/20211005120836.60630-1-roberto.sassu@huawei.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
I currently don't have time to act as vfio-ccw maintainer
anymore, but I trust that I leave it in capable hands.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eric Farman <farman@linux.ibm.com>
Acked-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Link: https://lore.kernel.org/r/20211006160120.217636-3-cohuck@redhat.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
I currently don't have time anymore to review KVM/s390
code.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Link: https://lore.kernel.org/r/20211006160120.217636-2-cohuck@redhat.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Justin Iurman says:
====================
Correct the IOAM behavior for undefined trace type bits
(@Jakub @David: there will be a conflict for #2 when merging net->net-next, due
to commit [1]. The conflict is only 5-10 lines for #2 (#1 should be fine) inside
the file tools/testing/selftests/net/ioam6.sh, so quite short though possibly
ugly. Sorry for that, I didn't expect to post this one... Had I known, I'd have
made the opposite.)
Modify both the input and output behaviors regarding the trace type when one of
the undefined bits is set. The goal is to keep the interoperability when new
fields (aka new bits inside the range 12-21) will be defined.
The draft [2] says the following:
---------------------------------------------------------------
"Bit 12-21 Undefined. These values are available for future
assignment in the IOAM Trace-Type Registry (Section 8.2).
Every future node data field corresponding to one of
these bits MUST be 4-octets long. An IOAM encapsulating
node MUST set the value of each undefined bit to 0. If
an IOAM transit node receives a packet with one or more
of these bits set to 1, it MUST either:
1. Add corresponding node data filled with the reserved
value 0xFFFFFFFF, after the node data fields for the
IOAM-Trace-Type bits defined above, such that the
total node data added by this node in units of
4-octets is equal to NodeLen, or
2. Not add any node data fields to the packet, even for
the IOAM-Trace-Type bits defined above."
---------------------------------------------------------------
The output behavior has been modified to respect the fact that "an IOAM encap
node MUST set the value of each undefined bit to 0" (i.e., undefined bits can't
be set anymore).
As for the input behavior, current implementation is based on the second choice
(i.e., "not add any data fields to the packet [...]"). With this solution, any
interoperability is lost (i.e., if a new bit is defined, then an "old" kernel
implementation wouldn't fill IOAM data when such new bit is set inside the trace
type).
The input behavior is therefore relaxed and these undefined bits are now allowed
to be set. It is only possible thanks to the sentence "every future node data
field corresponding to one of these bits MUST be 4-octets long". Indeed, the
default empty value (the one for 4-octet fields) is inserted whenever an
undefined bit is set.
[1] cfbe9b0021
[2] https://datatracker.ietf.org/doc/html/draft-ietf-ippm-ioam-data#section-5.4.1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The output behavior for undefined bits is now directly tested inside the bash
script. Trying to set an undefined bit should be refused.
The input behavior for undefined bits has been removed due to the fact that we
would need another sender allowed to set undefined bits.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for undefined bits in the trace type is moved from the input side to
the output side, while the input side is relaxed and now inserts default empty
values when an undefined bit is set.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ksz module is installed and removed using rmmod, kernel crashes
with null pointer dereferrence error. During rmmod, ksz_switch_remove
function tries to cancel the mib_read_workqueue using
cancel_delayed_work_sync routine and unregister switch from dsa.
During dsa_unregister_switch it calls ksz_mac_link_down, which in turn
reschedules the workqueue since mib_interval is non-zero.
Due to which queue executed after mib_interval and it tries to access
dp->slave. But the slave is unregistered in the ksz_switch_remove
function. Hence kernel crashes.
To avoid this crash, before canceling the workqueue, resetted the
mib_interval to 0.
v1 -> v2:
-Removed the if condition in ksz_mib_read_work
Fixes: 469b390e1b ("net: dsa: microchip: use delayed_work instead of timer + work")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following build/link errors by adding a dependency on
CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32:
ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum':
r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash'
ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest'
ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm'
ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode':
r8152.c:(.text+0xdcb0): undefined reference to `crc32_le'
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_port_ppu_updates() interpretes data in the PORT_STS
register incorrectly for internal ports (ie no PPU). In these
cases, the PHY_DETECT bit indicates link status. This results
in forcing the MAC state whenever the PHY link goes down which
is not intended. As a side effect, LED's configured to show
link status stay lit even though the physical link is down.
Add a check in mac_link_down and mac_link_up to see if it
concerns an external port and only then, look at PPU status.
Fixes: 5d5b231da7 (net: dsa: mv88e6xxx: use PHY_DETECT in mac_link_up/mac_link_down)
Reported-by: Maarten Zanders <m.zanders@televic.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/mscc/ocelot.c:474:duplicated argument to & or |
drivers/net/ethernet/mscc/ocelot.c:476:duplicated argument to & or |
drivers/net/ethernet/mscc/ocelot_net.c:1627:duplicated argument
to & or |
These DEV_CLOCK_CFG_MAC_TX_RST are duplicate here.
Here should be DEV_CLOCK_CFG_MAC_RX_RST.
Fixes: e6e12df625 ("net: mscc: ocelot: convert to phylink")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Then name of this protocol changed in commit 94531cfcbe ("af_unix: Add
unix_stream_proto for sockmap") because that commit added stream support
to the af_unix protocol. Renaming the existing protocol makes a ChromeOS
protocol test[1] fail now that the name has changed in
/proc/net/protocols from "UNIX" to "UNIX-DGRAM".
Let's put the name back to how it was while keeping the stream protocol
as "UNIX-STREAM" so that the procfs interface doesn't change. This fixes
the test and maintains backwards compatibility in proc.
Cc: Jiang Wang <jiang.wang@bytedance.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Cong Wang <cong.wang@bytedance.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Link: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/tast-tests/src/chromiumos/tast/local/bundles/cros/network/supported_protocols.go;l=50;drc=e8b1c3f94cb40a054f4aa1ef1aff61e75dc38f18 [1]
Fixes: 94531cfcbe ("af_unix: Add unix_stream_proto for sockmap")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last byte of "pad" is used without being initialized.
Fixes: 55dba3120f ("libata: update ->data_xfer hook for ATAPI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
* Fix a new crash on dev file close if the dev file was opened when
GPU is not loaded (such as missing fw in initrd)
* Switch to single drm_sched_entity per priority level per drm_file
to unbreak multi-context userspace
* Serialize GMU access to fix GMU OOB errors
* Various error path fixes
* A couple integer overflow fixes
* Fix mdp5 cursor plane WARNs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtD4u7yyiy+BQLmibUCbn=AdDRu7FrmdViHVx0QrcGf8g@mail.gmail.com
This disables a lock which wasn't enabled and it does not disable
the first lock in the array.
Fixes: 6e0eb52eba ("drm/msm/dsi: Parse bus clocks from a list")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211001123409.GG2283@kili
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Vladimir Oltean
Jakub Kicinski
Alvin Šipraga
Baowen Zheng
Laurent Pinchart
Maxim Mikityanskiy
Aya Levin
Saeed Mahameed
Valentine Fatiev
Tariq Toukan
Shay Drory
Jonas Hahnfeld
Linus Torvalds
Jiazi Li
Ming Lei
Colin Ian King
Akilesh Kailash
Jackie Liu
Dan Carpenter
Florian Fainelli
Nicolas Saenz Julienne
Kai Vehmanen
Konstantin Komarov
Sachi King
Hui Wang
Sumit Garg
Jacob Keller
Roberto Sassu
Cornelia Huck
David S. Miller
Justin Iurman
Arun Ramadoss
Vegard Nossum
Maarten Zanders
Wan Jiabing
Stephen Boyd
Dave Airlie